dashboard DACIA SOLENZA 2004 Owner's Manual

80
BATTERY - FRONT HEADLIGHTS
80 - 11
Disconnect the (-) plug of the battery;
Dismount
the headlamp adjusting control from the turning lamp-headlamp assembly:
- pull backward the gasket of the headlamp adjustment corrector ( 1);
- detach from clips the protector (2) of the headlamp adjustment mechanism;
- loosen the locking nut ( 3);
- detach from clips the he adlamp adjustment control cable ( 4) from the headlamp
adjustment corrector and then from the fork (5);
Dismount the headlamp adjusting control from the other turning lamp-headlamp assembly .
Detach from clips the headlamp adjustment control cables and cut the attachment collars.
Dismount the headlamps adjustment control button.
Dismount the attachment nut of the headlamp adjustment control on the dashboard.
Dismount the bonnet opening control cable from the opening handle (see chapter 52).
Detach from clips, by means of a straight screwdriver, the cables passing bushing from the
cowl panel.
Remove the headlamps adjusting control cables from the cowl-passin g hole. Mark the mounting
position of the headlamps adjustment control cables.
REMOU NT I NG
Insert the headlamps adjusting control cables through the cowl-passing hole, observing the
existent position prior to dismounting.
Insert the bonnet opening control cable through the cables passing bushing.
DISMOUNTIN G1
2
V
56 34
Replacement of the headlamps mechanic adjustment control
vnx.su

BATTERY - FRONT HEADLIGHTS
80
80 - 12
Replacement of the headlamps mechanic adjustment control
Attach on the cowl panel, by means of clips, the cables passing bushing, ensuring the cockpit
co mpartment sealing against possible water drain along the cables passing bushing.
Mount the bonnet opening control cable in the opening handle (see chapter 52). Position the
headlamp s adjustment control on the dashboard.
Mount the attachment nut of the headlamps adjustment control on the dashboard.
Mo unt the headlamps adjustment control button and turn it in the position “3”.
Mount the headlamp adjustment control to a turning lamp-headlamp assembly :
-a ttach in clips by means of a straight screwdriver, the headlamp adjustment control cable
in fork (5) a n d t h en in the headlamp adjustment corrector;
- tighten initially the cable by hand till the fork ( 5) is in contact with support ( 6) so that fork
is remaining at max. 0.5 mm again st the support;
-block the headlamp adjustment cable by means of the nut ( 3);
-a ttach in clips the protector ( 2) o f t h e headlamp adjustment mechanism;
- position correctly the gasket of the headlamp adjustment corrector – the vertical adjustment
screw ( V) mu st come out through the gasket.
Mount the headlamp adjustment control of the other turning lamp-headlamp assembly.
Attach in the attachment points, by means of clips, the headlamps adjusting control cables,
replace and mount the attachment collars, observing the mounting position prior to the dismounting.
Keep a distance of approximate 40 mm
± 10 mm between the right cable and the cylinder
no .1 spark plug cable, in order to avoid the loses due to electric-magnetic induction.
Reconnect the battery ( -) term inal.
Switch on the headlamps and check the operation of the headlamps mechanic adjusting control.
The adju stment of the luminous spot dip of the headlamps in the downward sense of the vehicle
loading condition is to be performed by bringing the headlamps adjusting button in the “ 0” position
an d then in the desired condition.
REMA RK : The r equired tighteni ng moment of the attachment nut of th e headlamps
adju stment control on the dashboard: 2 Nm.
vnx.su

INSIDE AND REAR LIGHTING
81
81 - 8
DISMOUNTING
Disconnect the (-) plug of the battery.
Pull the seat ( 1) of the access flap ( 2) to the fuse box located in the cockpit, at the l eft end of
the dashboard. Carefully remove flap ( 2).
Dismount the attaching screws ( 3) of the fuse box on the driving post crossbeam and detach
it from clips (4)
R EMOU NT I NG
Attach in clips ( 4) the fuse box on the driving post crossbeam and mount the screws ( 3).
Carefully mount, the access flap ( 2) to the fuse box.
Connect the battery (-) terminal.
Perform functional tests, noticing the correct operation of all consumers supplied by means
of the cockpit fuse box.
OBSERVATION:
For vehicle equipped with programmable radio-tape player and electronic c lock, af-
ter battery reconnecting, the radio code must be introduced and the clock re-programmed.
If COBRA 3800 or COBRA 3900 alarms have been mounted on the vehicle, in the
fuse box, may be found fuses F29 with value 15 A (mounted in seat (5)) and F 30 with
value 5A (mounted in seat (6)).
Cockpit fuse box
2
1
4
4 3
35 6
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 1
This type of anti starting system is based on the key recognition, which has a special constructio n.
It may be separated in two elements which can be identified in the following way: the key head
(position A.) made of plastic, which c an be dismounted and the metal insertion (position B),
which is fixed and ensured by clipping in the key head.
In the key head, there is a coded independent electronic circuit, which is functioning without
battery. When setting the contact on, the anti starting bushing, placed around the starting contact,
is enquiring and catching the coded signal emitted by the key head, then sends it to the Electronic
Control Unit (E.C.U.) decoder. This one is attached on the front left pillar, under the lower casing
of the dashboard and has the function of receiving the code sent from the bushing. If the decoder
recognises the key code then it will send a coded signal to the injection computer, which compares
it with the previous memorised code and will authorise or not the engine starting In case of the system with ra dio frequency remote control (RF) of the doors blocking /
unlocking, the key head has a different construction, having an activation button of the remote
control and a red L ED, which i s lighted i n the moment of bl ocking/unlocking the doors, by
pushing the key button. Inside t he ke y head there i s the coded electroni c c ircuit for the anti
starting system and a printed electronic circuit, supplied by a battery, for the RF remote control
operation of blocking/unlocking the vehicle doors.
The anti starting system is activated after approximate 10 seconds from the breaking of the
contact and is visualised by the blinking of the anti starting indicator placed on the instrument
panel.
AT T E N T I O N !
If the battery is low charged, the tension drop on the starter, at starting, may cause
the activation of the anti starting system and the engine starting is impossible.
General
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 17
Procedures
D. SIMPLE SYNCHRONISED PROCEDURE
This procedure allows the synchronisation of a RF remote control with E.C.U. decoder and
is to be applied in the following situations: -the RF remote control c ode is no longer in the range of the E .C.U. decoder reception,
because of blind consecutive pushing over a 1000 time on the RF remote control button.;
- the replacement of the E .C.U. decoder with a new one;
- the replacement of the RF remote control if the E.C.U. decoder is new (E.C.U. decoder
replacement plus a RF key.);
The following operations will be performed: -take off the contact;
- push and maintain like that for about 5 seconds, the doors locking switch located on the
dashboard ; the doors actuators are performing a closing/opening course;
- during the next 10 seconds, confirmed by the permanent lightening of the anti starting
system indicator, push twice the RF remote control button; the doors actuators are performing a
closing/opening course;
-the procedure of synchronisation is finished; check the doors blocking/ unlocking by
pushing the RF remote control.
OBSERVAT ION:
During those 10 seconds you can visualise by means of the CLIP tester t he state 17G
“PROGRAMMING OR TIR/TRF RESYNCHRONISATION” which must be ACTIVE.
E. SPECIFIC SYNCHRONISED PROCEDURE
This procedure is used for the synchronisation of the second RF key with E.C.U. decoder
and will be performed as follows:
-connect the CLIP tester to the diagnostic socket and the battery (or the lighter socket)
of the vehicle;
- select the vehicle type “B41”;
- select the menu “ COMPUTERS TEST” then “ ANTI STARTING”;
- enter the menu “COMMAND MODE” and select “CONFIGURATION”;
- validate the command “ PROGRAMMI NG THE SECOND TIR / TRF KEY” launching
the command from the blue button situated on the right top of the screen; the doors actuators are
performing a closing/opening course. - during the next 10 seconds, confirmed by the permanent lightening of the anti starting
system, push twice t he RF remote control button; the doors will block and then unlock and the
anti starting indicator will turn off. The second remote control is now synchronised. Check the
blocking/ unlocking by pushing the RF remote control.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 29
Diag nostic
ALP3. THE ANTI STARTING INDICATOR REMAINS PERMANENTLY LIGHTED
( even when the contact is taken off) OR IT REMAINS PERMANENTLY SWITCHED
OFF
RECOMMENDATION Check if the “Procedure E.C.U. decoder replacement” was correctly performed
Check the fuse F03 condition from the cockpit
fuse box.
Is the fuse good?
Is there the failure “DOORS BLOCKING
CONTACT”.
Check the continuity and the isolation related
to the mass, between the pin A 5 of the E.C.U.
decoder and the dashboard.(pin 6 from black
connector)
Is the wiring good?
Replace the fuse.
Analyse this failure and replace.
Fix the wiring.
Perform the following tests in order to find the
damaged element:
- if the anti starting indicator is permanently
lighted, disconnect the connector of the E.C.U.
decoder a nd check if t he indicator switches
off;
- if the anti starting system is turned off, connect
the pin A5 of t he wiring connector from the
E.C.U. decoder to an electric mass and check
if the indicator turns on.
Are the answers affirmatives?
Replace the instrument panel.
Replace the E .C.U. decoder.
Perform a conformity checking.
AFTER REPAIRING Check the operation of the anti starting system.
Remove by means of the CLIP tester the possible m emorised
failures.
No
No
No
Yes
Y e s
No
Yes
Yes
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 33
Diag nostic
ALP7. UNLOCKING DOORS NOT OPERATING BY RF REMOTE CONTROL
RECOMMENDATION Check the absence of failures with the CLIP tester.
If there are memorised failures, these must be repaired.
Are the states 11G and 11D be c om ing
A CTIVE when t he RF remote c ontrol is
activated?S ee the treatment of the states 11G
and 11D cf. chapter “Diagnostic”.No
Check the fuse F03 condition from the cockpit
fuse box.
Is it good?
Replace the fuse.No
Ye s
Yes
See the treatment of the failure
“Doors blocking contact” and the state 14 G cf. chapter
“Diagnostic”.
See ALP6.
Yes
No
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
Activate the doors’ locking switch from the
dashboard.
Are the doors blocking/ unlocking ?
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 40

Cockpit Central Unit
For anti-star ting function , the Cockpit Central Unit is ensuring the following functions:
- key signal decoding
- dialoguing with the injection computer.
- Conducting the anti-starting indicator placed on instrument panel.
- Dialoguin g with the diagnostic tester.
Cockpit Central Unit (C) is placed on the driving post left part, being attached on the dashboard
lateral side, in a protection box.
For dismounting please see Chapter 87.
Anti-starting indicator, placed on instrument panel, it is used to signal:
- anti-starting system activatio n
- key non-recognition
-a system failure
- key programming
C
Diagnostic – General
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 44
Diagnostic – General
-If doors are unlocked and none of them is
not opened in the next 30 seconds, the system
is automatically re-locking the vehicle doors
(without hazard lights blinking). -Cockpit central Unit is controlling the
vehicle inside lightening. In case a ceiling lamp
still lighted, Cockpit Central Unit is cutting the
supplying after approximately 30 minutes.
- The model “Full equipment” is controlling
the ceiling lamp progressive turning off, after
doors blocking by means of the remote control.
- Cockpit Central Unit may set on the hazard
lights in case of “shock connection” information
coming from UCE airbag.
-S pare parts keys are delivered not coded,
so they have no code.
-I t is possible in case of key’s l oss, theft or
by client’s request, that one vehicle ke y is
decommissioned. This one may be re-assigned
on the same vehicle, if necessary.
ATT E NT ION:
〈〈 〈〈
By this sy stem , i t i s i mp os s ib le th e
replacem ent of Coc kpit Central Unit and
keys in the same time. These parts are sold
not coded. 〈〈〈〈
The code me morized by the system’s
elements can not be erased (Cockpit
Central Unit and injection computer). The
memorized code can not be erased.
GENERAL
Cockpit Central Unit (UCH) is replacing
the UCE decoder.
Cockpit Ce ntral Unit is located under
dashboard, left side.
I MPORTANT
When replacing the Cockpit central Unit
it will be necessary to set the function
correspon ding to the vehicle equipment level,
by means of the CLIP tester.
ATT E NT ION
Starting is impossible unless the anti-
starting programming procedure is
performed.
When replacing a Cockpit Central Unit, it
is necessary to perform the programming and
settin g corresponding to the vehicle equipment
level.
When adding a key it is necessary that keys
re-assignation procedure be performed.
System’s characteristics.
- This system may work with maximum 4
remote controls (Cockpit central unit can
manage only 4 different codes).
-Radio-fr equenc y si gnal receive r i s
integrated in Cockpit Central Unit
-D oors central locking button is not
activated when doors ha ve be en c losed by
means of the remote control.
-Doors locking and unlocking using the
remote control may be visualized by hazard
lights signals (if all doors are properly closed);
- locking : 2 signals
- unlocking: 1 signal
vnx.su

INSTRUMENT PANEL
83
83 - 4
DISMOUNTIN G
Disconnect the battery (-) terminal.
Dismount the 3 attachment screws of the steering wheel half-casing, by means of a TORX 20
screwdriver. Detach from clips the steering wheel half-casings and remove them.
By means of a TORX 20 wrench (“L” shaped), dismount the side attachment screws of the
upper dashboard. By means of a TORX 20 screwdriver dismount the two front attachment screws of the upper
dashboard. Detach from the three clips of the windscreen lower crossbeam, the upper dashboard.
Di smount the radio-tape pl ayer from the upper dashboard (if the vehicle is equipped with
radio): press its side c lips and extract it from the upper da shboard. Disconnect the a ntenna’s
connector and the radio-tape two connectors. Disconn ect the central locking switch connector (if the vehicle is provided with central locking).
Remove the upper dashboard towards vehicle right part.
By means of a TORX 20 screwdriver, dismount the a ttachment screws of the i nstrument
panel on the lower dashboard. Disconnect the four connectors of the instrument panel. Mark the identification mounting
position of the connectors.
R EMOU NT I NG
Perform the dismounting operations in the reverse order.
Perform functional tests of the instrument panel.
OBSERVATION: After battery reconnecti ng, re-program the clock and for the
vehicles equipped with programmable radio, reinsert the radio code.
P erform functional instrument panel
vnx.su