DACIA SOLENZA 2004 Repair Manual

BATTERY - FRONT HEADLIGHTS
80
80 - 10
FOG P ROJECTORS ADJUSTMENT
The fog projectors adjustment is to be performed in the following conditions:
- the vehicle to be placed on a horizontal surface;
- the vehicle has not passengers inside the cockpit or weights in the trunk;
- the tires a re pressurized a t the manufacturer prescribed pressure.
Further on, proceed as follows:
Bring the vehicle at the working place.
Position the adjustment device (headlamp adjustment device –E) in front of an optical center
of a fog lamp. Switch on the fog projectors. Rotate the adjustment screw of the fog lamp (D), by means of
a scre wdriver ( A), so that a n adjustment of 2 % i s obtained and t he separation between t he
lighted area and the dark one from the adjustment device is l ocated under the marked line (G)
This adjustment is to be performed in the same way as for the meeting lights adjustment.
Bring the adjustment device in front of the optical center of the second fog lamp;
Perform the fog projector adjustment;
Switch off the fog projectors.
H eadlamps adjustment
G
E
A
vnx.su

80
BATTERY - FRONT HEADLIGHTS
80 - 11
Disconnect the (-) plug of the battery;
Dismount
the headlamp adjusting control from the turning lamp-headlamp assembly:
- pull backward the gasket of the headlamp adjustment corrector ( 1);
- detach from clips the protector (2) of the headlamp adjustment mechanism;
- loosen the locking nut ( 3);
- detach from clips the he adlamp adjustment control cable ( 4) from the headlamp
adjustment corrector and then from the fork (5);
Dismount the headlamp adjusting control from the other turning lamp-headlamp assembly .
Detach from clips the headlamp adjustment control cables and cut the attachment collars.
Dismount the headlamps adjustment control button.
Dismount the attachment nut of the headlamp adjustment control on the dashboard.
Dismount the bonnet opening control cable from the opening handle (see chapter 52).
Detach from clips, by means of a straight screwdriver, the cables passing bushing from the
cowl panel.
Remove the headlamps adjusting control cables from the cowl-passin g hole. Mark the mounting
position of the headlamps adjustment control cables.
REMOU NT I NG
Insert the headlamps adjusting control cables through the cowl-passing hole, observing the
existent position prior to dismounting.
Insert the bonnet opening control cable through the cables passing bushing.
DISMOUNTIN G1
2
V
56 34
Replacement of the headlamps mechanic adjustment control
vnx.su

BATTERY - FRONT HEADLIGHTS
80
80 - 12
Replacement of the headlamps mechanic adjustment control
Attach on the cowl panel, by means of clips, the cables passing bushing, ensuring the cockpit
co mpartment sealing against possible water drain along the cables passing bushing.
Mount the bonnet opening control cable in the opening handle (see chapter 52). Position the
headlamp s adjustment control on the dashboard.
Mount the attachment nut of the headlamps adjustment control on the dashboard.
Mo unt the headlamps adjustment control button and turn it in the position “3”.
Mount the headlamp adjustment control to a turning lamp-headlamp assembly :
-a ttach in clips by means of a straight screwdriver, the headlamp adjustment control cable
in fork (5) a n d t h en in the headlamp adjustment corrector;
- tighten initially the cable by hand till the fork ( 5) is in contact with support ( 6) so that fork
is remaining at max. 0.5 mm again st the support;
-block the headlamp adjustment cable by means of the nut ( 3);
-a ttach in clips the protector ( 2) o f t h e headlamp adjustment mechanism;
- position correctly the gasket of the headlamp adjustment corrector – the vertical adjustment
screw ( V) mu st come out through the gasket.
Mount the headlamp adjustment control of the other turning lamp-headlamp assembly.
Attach in the attachment points, by means of clips, the headlamps adjusting control cables,
replace and mount the attachment collars, observing the mounting position prior to the dismounting.
Keep a distance of approximate 40 mm
± 10 mm between the right cable and the cylinder
no .1 spark plug cable, in order to avoid the loses due to electric-magnetic induction.
Reconnect the battery ( -) term inal.
Switch on the headlamps and check the operation of the headlamps mechanic adjusting control.
The adju stment of the luminous spot dip of the headlamps in the downward sense of the vehicle
loading condition is to be performed by bringing the headlamps adjusting button in the “ 0” position
an d then in the desired condition.
REMA RK : The r equired tighteni ng moment of the attachment nut of th e headlamps
adju stment control on the dashboard: 2 Nm.
vnx.su

81
INSIDE AND REAR LIGHTING
81 - 1
REAR LAMPS
RE AR LAMP REPLACEMENT
DISMOUNTIN G
Disconnect the battery (-) plug.
Disconnect the rear lamp connector .
Inside trunk, dismount the screw with triangle head ( A).
Extract the rear lamp towards outside.
R EMOU NT I NG
Perform the dismounting operations in the reverse order, positioning correctly the rear lamp in
its seat. Check the bulbs connections and operation.
Rear right lamp Rear left lamp
Rear right lamp connector Rear left lamp connector
Pin Denomination Pin Denomination
1+ Right stop lamp 1 Fog parking lamp supply
2+ Right parking lamp 2 Left turning lamp supply
3Free 3 Free
4 Mass 4 Mass
5 Right turning lamp supply 5 + Left stop lamp
6 Revere driving lamp supply 6 + Left parking lamp
Inside and rear lighting
A
6
1 B
B
B
B 6
1
vnx.su

INSIDE AND REAR LIGHTING
81
81 - 2
R
EPLACEMENT OF REAR TURNING,
P ARK ING, FOG, REVERSE DRIVING,
STOP BULB
DISMOUNTIN G
Disconnect the battery (-) terminal.
Disconnect the rear lamp connector
Dismount the screw with triangle head
Extract the rear lamp towards outside
Di smount the two attachment screws (B) of
the bulbs support on the lamp glass.
Dismount the worn bulb.
REMOU NT I NG
Perform the dismounting opera tions i n the
reverse order, checking the condition of the
s ealing ga sket between the lamp glass and the
bulbs support: if this one is not good, replace it.
Check the bulbs operation and connections.
REPLACEMENT OF LICENSE PLATE LAMP BULB
DISMOUNTIN G
Disconnect the battery (-) terminal.
Disconnect the license plate lamp connector.
Extract the license plate lamp holder.
Remove the worn bulb and replace it.
R EMOU NT I NG
Perform the dismounting opera tions i n the
reverse order. Check the bulb operation.
REPLACEMENT OF ADDITIONAL
STOP LAMP BULB
DISMOUNTIN G
Disconnect the battery (-) terminal.
Dismount the TORX 20 attachment screw
of the additional stop lamp. Mark the mounting
position of the lamp mass wire connector.
Inside and rear lighting
Disconnec t t he addit ional st op l amp
connector. Detach t he two side clips and extra ct the
reflector-glass assembly from the lamp body.
Detach carefully from clips the lamp glass,
by means of a straight screwdriver. Replace the worn bulb.
REMOU NT I NG
Perform the dismounting operations in the
reverse order. Check the bulb connections and
operation.
REPLACEMENT OF LICENSE PLATE LAMP
DISMOUNTIN G
Disconnect the battery (-) terminal.
Disco nnect the license plate lamp
connector. Detach from clips the license plate lamp.
REMOUNTING
Pe rform t he di smounting opera tions i n t he
reverse order. Check the bulb operation.
R EPLACEMENT OF ADDITIONAL
STOP LAMP
DISMOUNTIN G
Disconnect the battery (-) terminal.
Dismount the attachment screw TORX 20
of the additional stop lamp. Mark the mounting
position of the lamp mass wire connector.
Disconnec t t he addit ional st op l amp
connector.
R EMOU NT I NG
Perform the dismounting operations in the
reverse order. Check the bulb connections and operation.
vnx.su

81
INSIDE AND REAR LIGHTING
81 - 3
R
EPLACEMENT OF THE SIDE REAR LAMP
DISMOUNTIN G
Dismount the attachment screws of the wing protector.
Dismount the wing protector
Disconnect the connector
Detach from clips the side rear lamp.
REMOU NT I NG
Perform the dismounting operations in the reverse order.
Inside and rear lighting
vnx.su

INSIDE AND REAR LIGHTING
81
81 - 4
The ceiling lamp is central located, between
the two sun visors.
The ceiling lamp has 3 operating positions
subject to ceiling lamp glass position (4):
- position 1 : ceiling lamp off
- position 2 delayed ceiling lighting; this
will light for 15 seconds after driver’s front door
closing or after the command of unlocking the
doors with the RF remote control . This delay
turns out in the moment of setting the contact.
- position 3 : c eiling lamp pe rmanently
lighting.
DISMOUNTIN G
Disconnect the battery ( -) terminal.
Detach from clips the assemb ly from the lamp
support by means of a little screwdriver acting in
front of the slot (A). Disconnect the connector
Remove the roof lining around ceiling lamp
support. Detach from clips the ceiling lamp support.
REMOU NT I NG
Perform the dismounting operations in t he
reverse order. Check the ceiling lamp operation. Ceiling lamp connector
Pin Denomination
1 Mass
2+
protected battery – exit fuse F02
3 Ceiling lamp control
REPLACEMENT OF CEILING LAMP BULB
DISMOUNTIN G
Disconnect the battery (-) terminal;
Detach care fully the lamp glass using a
small screwdriver acting in point ( B).
Remove the worn bulb and replace it.
R EMOU NT I NG
Perform the dismounting operations in the
reverse orde r, using for lamp glass clips
attachment, a small screwdriver positioned in
point (B).
Check the ceiling lamp operation.
Ceiling lamp
A
B
3 1
vnx.su

81
INSIDE AND REAR LIGHTING
81 - 5
Bulbs
BULBS
Headlamps High/low beam lights Bulb H4, 12V-60/55W Parking lights Bulb W5W, 12 V-5W
Front turning lamp Bulb PY21W, 12V-21W (colored)
F og projectors Halogen bulb H11, 12V-55W
Rear Parking, stop lights Bulb AB1, 12V-21/5W
lamps Turning lights Bulb PY21W, 12V-21W Rear fog lamp and reverse driving Bulb P21W 12V/21W
Rear side signalin g lamps Bulb WY5W 12V-5W
Ceiling lamp Bulb C5W, 12V-5W
License plate lamp Bulb W 5W, 12V-5W
Additional STOP lamp Bulb C21W, 12V/21W Sv8,5
Instrument panel Bulb12V, 2W (brown holder)
Bulb 12V, 1,2W (black holder)
Climate control panel Bulb 12V, 1,2 W
(black holder
vnx.su

INSIDE AND REAR LIGHTING
81
81 - 6
Lamps failures diagnostic
FOG LAMP NOT WORKING
Ye s
Ye s
Ye s Ye s
No
No No
No
Replace fuse F06
Replace the STOP contact
Replace fuse F19
Replace under steering
wheel control. Check fuse F06 from cockpit fuse box.
Is it worn?
Check the continuity and resistance against vehicle mass between:
- exit fuse F06 pin2 reverse driving contact c onnector
- pin1 reverse driving contact connector pin 6 right rear lam
connector
- pin 4 right rear l amp connector vehicle m ass
Ar e they good?
Defective wiring. Fix it.
Check fuse F19 from cockpit fuse box. Is
it worn? Check the continuity and
resistance against vehicle mass between:
- battery pin B2 light control lever and signaling,
- pin A3 inlet fuse F19,
- exit fuse F19 pi n 1 left rear lamp connector,
- pin 4 left rear l amp connector vehicle m ass.
Ar e they good?
Defective wiring. Fix it.

REAR DRIVI NG LAMP NOT WO RKING
vnx.su

81
INSIDE AND REAR LIGHTING
81 - 7
Lamps failures diagnostic
STOP LAMPS NOT WORKING
Check fuse F04 from cockpit fuse box.Is it good?
Replace fuse F04Yes
Yes
No No
No
Ye s
Replace t he Stop contact
The stop contact wire supply is broken or disconnected. Fix it. Bridge the Stop contact terminals.
Are the lamps working?
Is the Stop contact supplied ?
The stop contact wire supply is broken or disconnected. Fix it.
vnx.su