DACIA SOLENZA 2004 Repair Manual

CARRIAGE BODY INSIDE TRIMS
71
71 - 6
Trunk carpet
DISMOUNTING
Unstuck the trunk c arpet from the self-adhesive tapes placed on the rear floor.
REMOUNTING
Pe rform the dismounting operations in the reverse order.
vnx.su

71
CARRIAGE BODY INSIDE TRIMS
71 - 7
DISMOUNTING
Dismount :
- dashboard (see chapter 57 );
- driving post cross beam (see chapter 42 );
- centra l console ( see chapter 58);
- distributor of t he air ventilation climate maintenance RACV ( see chapter 61);
- attaching scre w of the steering column support on the dri ving post cross-beam;
- pedals support ( see chapter 37);
- partially the floor carpet ( i n the noise absorbent coveri ng area).
Detach the noise absorbent (2 ) from the cowl panel clips (1).
Cowl panel noise absorbent
REMOUNTING
Perform in the reverse orde r the dismounting opera tions.
A maximum 3 daN clips attaching effort is necessary for the noise absorbent attach-
ment clips.
21
vnx.su

CARRIAGE BODY INSIDE TRIMS
71
71 - 8
1 – cockpit carpe t
2 – clip
DISMOUNTING
Di
smount :
- front seats ( see chapter 78 );
- rear bench seat (see chapter 78);
- front seat belts lockers ( see chap-
ter 59 )
- centra l console ( see chapter 58);
- distributor of the air ventilation/cli-
mate maintenance RACV (see chapter 61 );
- front safety belts at lower part;
- accelera tion pedal limiter.
D etach from clips the cockpit carpet ( 1).
REMOUNTING
Perform the dismounting opera tions in the
reverse order.
The clips attaching is to be performed with
a maximum forc e of 3 daN.
Cockpit carpet
1
2
vnx.su

72
72 - 1
LATERAL OPENINGS TRIMS
Front door panel
DISMOUNTIN G
Disconnect the battery.
Dismount :
- window regulator crank (A) for glass
lifting , that is mounted by clips attachment on
the window regulator axle ( in case of the
vehicles provided with glass hand-drive lifting);
- attachment screw of the open ing
mechanism from inside (B), consequently the
mechanism. - locking handle (C) attached by screw.
Rotate the speaker grill (D) counter clock-
wise direction and extract it from the front door
panel.
Dismount the four attachmen t screws of the
s peaker on the door pa nel.
Disco n n ect the front door speaker
connector. Dismount the attachment screws (1 ) of the
door panel on the caisson.
D C
1
1
CD 1
2
B
A
Detach from clips the door panel in poi nts
(2) .
R EMOU NT I NG
Perform in the reverse order the dismounting
operations taking i nto account t he following
recommendations: - check the integrity of the deflective
panel and of the continuos layer of Romtix
1502 P sealing materi al on the front door
caisson; - for the mounting of the inside opening
mechanism, the opening control rod will be
placed in the position where the assemble d plate
with electric control is blocked;
- after mounting, check the operation of
the inside opening mechanism and its alignment
with the front door panel; - check t he ope ration of t he front door
speaker.
vnx.su

72
72 - 2
LATERAL OPENINGS TRIMSRear door panel
1 C
B
1A 2
C
2
DISMOUNTIN
G
Dismount :
- window regulator cra nk (A) for glass
lifting that is mounted by clips attachment on
the window regulator axle.
- attachment screw of the inside opening
mechanism (B), consequently, the mechanism;
- locking handle (C) attached by screw;
- attachment screws (1) of the rear door
panel on the caisson; Detach from clips the rear door panel from
points (2).
REMOU NT I NG
Perform the dismounting operations in the
reverse orde r, taking into considera tion the
followings recommendations: - check the integrity of the deflectiv e panel
and of the continuos sealant material layer
Romt ix 1502 P on the door caisson outliner;
- for the mounting of the inside opening
mechanism, the opening control rod will be
placed in the position where the assemble d plate
with electric control is unblocked. - after mounting, check the operation of
the inside opening mechanism and its alignment
w ith the rear door panel.
vnx.su

74
REAR TABLE
74 - 1
Lateral table
DISMOUNTING
Release t he t able cord from button (3)
that is attached on the hatchback by means
of the screw (2) and the nut (4).
Extract the panel (1).
Release the rear table (1) from t he latera l
s upports channel.
Di sconnect the battery.
Di sconnect the rear speaker connector.
Di smount the attachment screws of the
rear bench on its supports.
Recline the bench backrest.
Dismount:
-scr ew (8) from the maintaining c lip (7 )
attaching the table l ateral support on t he l at-
eral fra me lining; -scr ews (5) from maintaining clips (6)
attachin g the table later al suppor t on the
bench support.
Detach from clips, the table latera l sup-
port ( 9), from rear qua rter panel tri m. Di
smount the speaker from the table lat-
eral support.
REMOUNTING
Pe rform the dismounting operations in
the reverse order.
Attent ion !
The speaker is to be mounted with the
connector towards vehicle’s front part.
Check the operation of the rear speaker.
1 9
8
4
3
2
7
6
5
vnx.su

REAR TABLE
74
74 - 2
DISMOUNTING
Dismount the re ar plate.
Di smount by measn of a screwdriver, in
the arrow dire ction, the table pivot.
In case head of the pivot, its remaining is
inserted inside t he m etallic rod of the t able by
means of a screwdriver and a hammer, as per
bellow presented drawing.
REMOUNTING
Pe rform the dismounting operations in
the reverse order.
PIVOT
Lateral table
vnx.su

74
REAR TABLE
74 - 3
RE
AR PLATE BUFFER
DSIMOUNTING
Push the rear plate buffer by m eans of
a screwdriver accord ing to the bellow
presented dra wing
REMOUNTING
Pe rform the dismounting operations in
the reverse order. RE
AR PLATE CORD
DISMOUNTING
Dismount
-r ear table,
-the agra ffe of t he re ar plate cord
together with its c ord as pe r bellow presented
drawing.
REMOUNTING
Pe rform the di smounting opera tions in the
reverse order.
Lateral table
vnx.su

75
75 - 1
FRONT SEATS SLIDES GU IDES
Front seat
75 010
TIGHTENING
MOMENTS(daNm)
Fr ont seat attachment screws 2,1
DISMOUNTIN G
Dismount the attachment screws (1) of the
front seat on the side and central cross mem-
ber in the front part.
By acting upon the lever (2) in the arrow
direction, bring the seat in front position and
dismount the attachment screws (3) of the front
seat on the side and re ar c ross-beam in the
rear part.
1 2 3
4
5
Release the front chair.
Remove the headrests by simultaneously
pushing of the buttons (4) attached on the head-
rests sleeves.
R EMOU NT I NG
Perform the dismounting operations in the
reverse order.
The front seat attachment screws are to be
tighten to the required moment of 2,1 daNm.
ADJUSTMENTS
The front seats, have two possibilities of ad-
justment:
- front or rear longitudinal movement,
w hich can be performed by lever’s operation
(2); - seat back reclining up to the horizontal
position, by rotating the round button (5).
vnx.su

75
75 - 2
FRONT SEATS SLIDES GU IDES
DISMOUNTIN G
Dismount the front seat ( see chapter 78 “ Seats”).
In order to dismount the attachment screws (1) of the slides guides (2) and (3) on the front
s eat, it is necessary the backward and forward slides guides moving, by acting upon the lever
(4).
Release the slides guides from the front seat.
4
1 5
3
2
REMOU NT I NG
Perform the dismounting operations in the reverse order.
When remounting, observe the positioning of the four spacers (5).
Front seats slides guides
vnx.su