engine DACIA SOLENZA 2004 Workshop Manual

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 42
Multi-purpose support
TIGHTENI NG MOMENTS (daNm)
Sup port attachment screws 4
Sup port upper attachment screws 2
DISMOUNTIN G
Place t he vehicle on a two-column elevator.
Disconnect the battery.
Dismount :
-compressor (see chapter 62”Air
conditioning ”) for vehicles equipped with a ir
conditioning unit; -power steering pump (see chapter 36 “
Power steering pump”) for vehicles equipped
with power steering.
- Dismoun t the support attachment screws.
2
2
REMOU NT I NG
Position the support and pre-tighten the
central screw (1) to the required moment of
0.25 daNm. Mount the others attachment screws.
Tighten to the required moment observing
the sequence shown in the drawing. Remount the other elements by
performing the dismounting operations in the
reverse order.
Supp Support AD S
upport AC/AD
vnx.su

ENGINE E7J-26211
11 - 1
DISTRIBUTION SYSTEMDistribution belt
DISMOUNTIN G
Place the vehicle on a two-column eleva-
tor.
Mount between chassis and cylinder casing,
the MOT. 545 device for sustainin g front part
engine.
TIGHTENING MOMENTS (daNm)
Wheels screws 7.5
C rankshaft pulley screw 2+68
0 ± 60
Te nsioning roller nut 5
R ight support screws 6.2
Hydro-elastic buffer nut 3.7
Dismo unt :
-r ight front wheel;
-r ight pendular suspension support;-
accessories belt ( for vehicles provided
with air conditioning and/or power steering; -alternator’s belt;
-cr ankshaft’s pulley or pulleys and their
hub ; -distribution casings.
vnx.su

ENGINE E7J-26211
11 - 2
DISTRIBUTION SYSTEMDistribution belt
Set the engine at setting poi nt (see method described in chapter 10 “ Engine assembly”,
page 10 –19). Loosen the tensioning roller nut.
Dismount the distribution belt.
REMOU NT I NG
Mount a new distribution belt.
Tension the distribution belt to a value of 145 – 185 Hz by means of the MOT 1505 device
(see the method described in c hapter 10 “ Engine assembly”, page 10 –33 ).
Perform the dismounting operations in the reverse order.
Tighten to the required moment the screws.
Remount the pulley for accessories belt (for vehicles equipped with air conditioning and/or
power steering). Obligatory tighten the screw of the crankshaft pulley hub to the required moment of 2 daNm
plus an angle of 68° ± 6 °
Mount and tension the alternator belt and the accessories belt, observing the method for belts
tensioning described in chapter 07 “ Accessories belts tensioning “.
The belts te nsioning values are:
Alternator belt 253 – 273 Hz
Co mpressor belt 150 – 155 Hz
Power steering pump belt 151 – 161 Hz
Co mpressor / power steering pump belt 214 – 230 Hz
vnx.su

ENGINE E7J-26211
11 - 3
DISTRIBUTION SYSTEM
3
1
42
Cylinder head gasket
N
ecessary Special Tools
MOT 1202-01 Pliers for e lastic collars
MOT 1505 Belt te nsioning measurement device
MOT 484 Jackets clamping device Wrench for angle tightening
Wrench for “CLIC” collars
TIGHTENING MOMENTS ( daNm )
Te nsioning roller nut 5
Crankshaft pulley screw 2 + 68° ± 6°
Pendular suspension support screws 6.2
Hydro-elastic buffer nut 3.7
Wheels screws 7.5
C ylinder head screws ( see cylinder head tightening method)
DISMOUNTIN G
Place the vehicle on a two-columns eleva-
tor. Disc onnect the battery.
Dr ain the cooling circ uit by the radiator
lower part hose.
Dismount the distribution belt (see chap-
ter 11 “ D i s t ribution belt “)
Dismount t he air filter
Disconnect : - acceleration cable from the valve con-
trol lever; -valve position potentiometer connec-
tor (1);
-atmospheric pressure sensor connec-
tor (2);
-step-by-step engine connector( 3);
- temperature sensor connector ( 4)
from the inlet manifold .
Disconnect :
-induction coil connector ( 5);
-f uel hoses (supply/return);
- injectors connectors;
- spark plugs cables.
Dismount the three attachment screws of the
induction coil ( 6).
vnx.su

ENGINE E7J-26211
11 - 4
DISTRIBUTION SYSTEM
56
Cylinder head gasket
Dismount the hoses from the thermostat sup-
port.
Dismou nt :
- compressor (see chapter 62 “Air con-
ditioning”); -power steering pump (see chapter 36”
Power steering pump );
- alternator (see chapter 1 6 “Alterna-
tor” ); -
oil gauge guide;
- thermal screen;
- multi-purpose support;
- exhaust manifold.
Dismo unt :
- cylinder head screws except the screw
corresponding to A position, which is to be
loosen, then rotate the cylinder head around the
screw remained not-dismounted; - cylinder head.
vnx.su

ENGINE E7J-26211
11 - 5
DISTRIBUTION SYSTEM
MOT 484
Cylinder head gasket
Mount the MOT 484 device or MOT
588 clamps for jackets maintenance.
Check the cylinder head smoothness using
a lineal a nd a set of templates. The maximal admissible deformation: 0.05
mm. The cylinder head is not to be rectified!REMOU NT I NG
Clean the gasket-seating surface of the cyl-
inder head.
Mount the cylinder head with a new gasket.
Perform the dismounting operation s in the re-
verse order.
Tighten the cylinder head observing the cyl-
inder head tightening method described in chap-
ter 10 “Dismounting-Remounting” .
Mount the distribution belt ( see chapter 11
”Distribution belt”).
Adjust the tilters.
Perform the cooling circuit filling and purging
(see chapter 19 “ Filling and Purging” ).
REMARK:
At each operation implying battery dis-
mounting,
when reconnecting it, introduce the radio
code t hat is written on the vehicle-purchas-
ing invoice.
vnx.su

ENGINE E7J-26212
12 - 1
F UEL M IXTURE
Chara cteristics
ENGINE
VehicleGearbox Type Index Bo re StrokeCylinder
(mm) (mm)capacity
(cm3)
SOLENZA JH3-051 E7J 262 75,8 77 1390 9,5/1
T (0C) 250C500C800C1100C
Air T sensor 2058 - 20 45 816 - 804 315 - 303 141 - 129
R (Ohm)
Water T sensor 2300 - 2100 850 - 750 275 - 290 110 - 120
R (Ohm)
(1) The CO value at 2500 rpm must be maximum 0.3 %.
〈 For a water temperature of over 80 ° C and after a steady value of 2500 rpm during 30
sec; after this, return to idle running and perform measurement of polluting emissions level.
The water and air temperature sensors are of CTN type (negative coefficient of temperature)
and their resistance variation subject to the temperature, has the following evolution:
Verificãri efectuate la ralanti *
Engine Emisii poluan
i Fuel
Ty p e I ndex Revolution CO(%) CO
2(%) HC Lambda (minimum octane
(RPM) (1) (ppm) ( λλλλ
) number)
E7J262 750 ± 50 0,5 14,5 100 0,97.... Unleaded fuel
ma xm inmax ....1,03 (CO95)
vnx.su

ENGINE E7J-26212
12 - 2
F UEL M IXTURE
DENOMINATION PARTICU LARITIES
UCE injection SIEMENS - Connector with 90 ways
In jection system Sequential multi-point
I gnition Static with double coil PINI R (W)
I gnition control led by
RA- C0,52
ΩΩΩΩ

± 10%

































UCE in
jectionRB-C0,52
ΩΩΩΩ

± 10%
R 1 -47,2 KΩΩΩΩ ±
10%
R
2-37,2 KΩΩ ΩΩ ±
10%
Characteristics
Detonation sensor Sagem – piezo-electric type
Tightening moment = 2 daNm.
RPM sensor ELECTRICFIL or SIEMENS
R = 200………….270 Ù
Spa rk plugs SAGEM – Type RFC 52 LZ
Ti ghtening moment = 2.5 –3 daNm
Fuel filter For de-pollution norm 1504
Mounted under the vehicle in front the fuel tank.
Replacement at every scheduled checking
For EURO 00 and EURO 96;
Insi de the fue l tank, attached on the fuel pump assembly.
Do not replace it separately.
Feeding pump Immersed in the fuel tank
For de-pol lution norm 1504:
- Flow: 1.3 l/min. Pressure: 3 bars at 12 V ten sion.
For EURO 00 and EURO 96:
- Pressure: 3.5 bars at 12 V tension.
Pressure regulator For de-pollution norm 1504:
Regulator attached on the injection ramp.
Adjusted pressure : 3 ± 0.2 b ars at zero depression
2.5± 0.2 bars at 500 mbars depression
For EURO 00 and EURO 96:
Mounted inside the fuel tank on the fuel pump assembly.
Adjusted pressure : 3.5 bars
Electro-magnetic Injectors SIEMEN S
R = 14.5 Ù ± 5 % AT 20 º C
Supply + 12V
Step by step engine R
A-D = 53 Ù 10% at 25º C
R
B- C = 53 Ù 10% at 25 ºC
vnx.su

ENGINE E7J-26212
12 - 3
F UEL M IXTURE
Characteristics
DENOMINATION PARTICULARITIES
Potentiometer with
valve
At idling running At maximum acceleration
A - B 1200 ΩΩΩΩ
±
20% 1200
ΩΩΩΩ±
20%
A - C 1400 ΩΩΩΩ

±
20% 2000
ΩΩΩΩ±
20%
B - C 2000
ΩΩΩΩ

±
20% 1200
ΩΩΩΩ±
20%
Can purging valve SAGE M
Supply voltage = + 12V
R = 26 W
± 7% at 23 °C
O xygen sensor NGK
For EURO 96 : one oxygen se nsor mounted
upstream of the catalyst. Generate d voltage at 850 °C:
- rich mixt ure : min 850 mV
- poor mixture : max 100 mV
He ating resistance at 23 °C : 6 W
± 1
For EURO 00 : two oxygen sensors mounted
one upstream and one downstream of the catalyst.
Generate d voltage at 850 C:
- rich mixt ure : min 850 mV
- poor mixture : max 100 mV
He ating resistance at 23 °C : 3.3 W
± 0,7
Atmos pheri c DE L CO E L ECT RONICS
pres s ure s en s or
Stopped engine – shows atmospheric pressure 950......1050
mbars
Idling running engine – 330
± 40 mbars
vnx.su

ENGINE E7J-26212
12 - 4
F UEL M IXTURE
Body valve
2
2
1
I
II
DISMOUNTIN G
Disconnect the battery.
Dismount the air inlet duct from the battery
protection screen. Dismount the air filter four attachment
screws.
Disconnect the hose ( 1) for oil vapors re-
aspiration, between the cylinder head cover and
the air filter. Remove the air filter.
Disconnect :
〈 Dismount acceleration cable ( disconnect
the cable end from the body control lever and
extract it from the support sleeve) 〈 connectors
I – of the step-by-step engine
II – of the body potentiometer
( pull upwards the no.2 clamp and disconnect
the connector). Disconnect the body control lever
Dismount
the valve body.
REMOU NT I NG
Replace the valve body gasket.
Perform the dismounting operations in the
reverse order.
vnx.su