DACIA SOLENZA 2004 Manual PDF

ENGINE E7J-26211
11 - 4
DISTRIBUTION SYSTEM
56
Cylinder head gasket
Dismount the hoses from the thermostat sup-
port.
Dismou nt :
- compressor (see chapter 62 “Air con-
ditioning”); -power steering pump (see chapter 36”
Power steering pump );
- alternator (see chapter 1 6 “Alterna-
tor” ); -
oil gauge guide;
- thermal screen;
- multi-purpose support;
- exhaust manifold.
Dismo unt :
- cylinder head screws except the screw
corresponding to A position, which is to be
loosen, then rotate the cylinder head around the
screw remained not-dismounted; - cylinder head.
vnx.su

ENGINE E7J-26211
11 - 5
DISTRIBUTION SYSTEM
MOT 484
Cylinder head gasket
Mount the MOT 484 device or MOT
588 clamps for jackets maintenance.
Check the cylinder head smoothness using
a lineal a nd a set of templates. The maximal admissible deformation: 0.05
mm. The cylinder head is not to be rectified!REMOU NT I NG
Clean the gasket-seating surface of the cyl-
inder head.
Mount the cylinder head with a new gasket.
Perform the dismounting operation s in the re-
verse order.
Tighten the cylinder head observing the cyl-
inder head tightening method described in chap-
ter 10 “Dismounting-Remounting” .
Mount the distribution belt ( see chapter 11
”Distribution belt”).
Adjust the tilters.
Perform the cooling circuit filling and purging
(see chapter 19 “ Filling and Purging” ).
REMARK:
At each operation implying battery dis-
mounting,
when reconnecting it, introduce the radio
code t hat is written on the vehicle-purchas-
ing invoice.
vnx.su

ENGINE E7J-26212
12 - 1
F UEL M IXTURE
Chara cteristics
ENGINE
VehicleGearbox Type Index Bo re StrokeCylinder
(mm) (mm)capacity
(cm3)
SOLENZA JH3-051 E7J 262 75,8 77 1390 9,5/1
T (0C) 250C500C800C1100C
Air T sensor 2058 - 20 45 816 - 804 315 - 303 141 - 129
R (Ohm)
Water T sensor 2300 - 2100 850 - 750 275 - 290 110 - 120
R (Ohm)
(1) The CO value at 2500 rpm must be maximum 0.3 %.
〈 For a water temperature of over 80 ° C and after a steady value of 2500 rpm during 30
sec; after this, return to idle running and perform measurement of polluting emissions level.
The water and air temperature sensors are of CTN type (negative coefficient of temperature)
and their resistance variation subject to the temperature, has the following evolution:
Verificãri efectuate la ralanti *
Engine Emisii poluan
i Fuel
Ty p e I ndex Revolution CO(%) CO
2(%) HC Lambda (minimum octane
(RPM) (1) (ppm) ( λλλλ
) number)
E7J262 750 ± 50 0,5 14,5 100 0,97.... Unleaded fuel
ma xm inmax ....1,03 (CO95)
vnx.su

ENGINE E7J-26212
12 - 2
F UEL M IXTURE
DENOMINATION PARTICU LARITIES
UCE injection SIEMENS - Connector with 90 ways
In jection system Sequential multi-point
I gnition Static with double coil PINI R (W)
I gnition control led by
RA- C0,52
ΩΩΩΩ

± 10%

































UCE in
jectionRB-C0,52
ΩΩΩΩ

± 10%
R 1 -47,2 KΩΩΩΩ ±
10%
R
2-37,2 KΩΩ ΩΩ ±
10%
Characteristics
Detonation sensor Sagem – piezo-electric type
Tightening moment = 2 daNm.
RPM sensor ELECTRICFIL or SIEMENS
R = 200………….270 Ù
Spa rk plugs SAGEM – Type RFC 52 LZ
Ti ghtening moment = 2.5 –3 daNm
Fuel filter For de-pollution norm 1504
Mounted under the vehicle in front the fuel tank.
Replacement at every scheduled checking
For EURO 00 and EURO 96;
Insi de the fue l tank, attached on the fuel pump assembly.
Do not replace it separately.
Feeding pump Immersed in the fuel tank
For de-pol lution norm 1504:
- Flow: 1.3 l/min. Pressure: 3 bars at 12 V ten sion.
For EURO 00 and EURO 96:
- Pressure: 3.5 bars at 12 V tension.
Pressure regulator For de-pollution norm 1504:
Regulator attached on the injection ramp.
Adjusted pressure : 3 ± 0.2 b ars at zero depression
2.5± 0.2 bars at 500 mbars depression
For EURO 00 and EURO 96:
Mounted inside the fuel tank on the fuel pump assembly.
Adjusted pressure : 3.5 bars
Electro-magnetic Injectors SIEMEN S
R = 14.5 Ù ± 5 % AT 20 º C
Supply + 12V
Step by step engine R
A-D = 53 Ù 10% at 25º C
R
B- C = 53 Ù 10% at 25 ºC
vnx.su

ENGINE E7J-26212
12 - 3
F UEL M IXTURE
Characteristics
DENOMINATION PARTICULARITIES
Potentiometer with
valve
At idling running At maximum acceleration
A - B 1200 ΩΩΩΩ
±
20% 1200
ΩΩΩΩ±
20%
A - C 1400 ΩΩΩΩ

±
20% 2000
ΩΩΩΩ±
20%
B - C 2000
ΩΩΩΩ

±
20% 1200
ΩΩΩΩ±
20%
Can purging valve SAGE M
Supply voltage = + 12V
R = 26 W
± 7% at 23 °C
O xygen sensor NGK
For EURO 96 : one oxygen se nsor mounted
upstream of the catalyst. Generate d voltage at 850 °C:
- rich mixt ure : min 850 mV
- poor mixture : max 100 mV
He ating resistance at 23 °C : 6 W
± 1
For EURO 00 : two oxygen sensors mounted
one upstream and one downstream of the catalyst.
Generate d voltage at 850 C:
- rich mixt ure : min 850 mV
- poor mixture : max 100 mV
He ating resistance at 23 °C : 3.3 W
± 0,7
Atmos pheri c DE L CO E L ECT RONICS
pres s ure s en s or
Stopped engine – shows atmospheric pressure 950......1050
mbars
Idling running engine – 330
± 40 mbars
vnx.su

ENGINE E7J-26212
12 - 4
F UEL M IXTURE
Body valve
2
2
1
I
II
DISMOUNTIN G
Disconnect the battery.
Dismount the air inlet duct from the battery
protection screen. Dismount the air filter four attachment
screws.
Disconnect the hose ( 1) for oil vapors re-
aspiration, between the cylinder head cover and
the air filter. Remove the air filter.
Disconnect :
〈 Dismount acceleration cable ( disconnect
the cable end from the body control lever and
extract it from the support sleeve) 〈 connectors
I – of the step-by-step engine
II – of the body potentiometer
( pull upwards the no.2 clamp and disconnect
the connector). Disconnect the body control lever
Dismount
the valve body.
REMOU NT I NG
Replace the valve body gasket.
Perform the dismounting operations in the
reverse order.
vnx.su

ENGINE E7J-26212
12 - 5
F UEL M IXTURE
TIGHTENING MOMENT (d aN m)
Inlet manifold nuts and screws 2,5
Inlet manifold
32 5 7
416
3
1
42
DISMOUNTIN G
Place the vehicle on a two-columns
elevator. Disconnect the battery.
Dismo unt :
- the air filter assembly;
- the acceleration cable from the body
control lever; - the injection ramp ( see c hapter 13
“Injection ramp”).
Disconnect the electric connectors:
- body position potentiometer ( 1)
- atmospheric pressure sensor (2)
- step-by-step engine (3);
- air temperature sensor( 4)
Disconnect the fuel supply ducts (supply and return)
Disconnect the petrol vapors re-aspiration hose from the inlet manifold.
Uncouple the body control lever and remove the valve body.
Dismount the attachment nuts and screws of the inlet manifold.
Extract the inlet manifold .
REMOU NT I NG
Replace the inlet manifold gaskets.
Tighten at the required moment the inlet manifold nuts and screws, observing the sequence
shown in the drawing.
Perform the dismounting operations in the reverse order.
vnx.su

ENGINE E7J-26212
12 - 6
F UEL M IXTURE
TIGHTENING MOMENT (daNm)
Exhaust manifold attachment nuts 2.5
Downward pipe attachment nuts on
Exhaust manifold 2
Exhaust manifold
14
26 37
5
DISMOUNTIN
G
Dismount the multi-purpose support ( see chapter 10 “ Multi-purpose support”)
Dismount the thermal screen.
Dismount the descending pipe attachmen t nuts on the exhaust manifold
Dismount the exhaust manifold attachment nuts.
Remove the manifold and its gasket.
R EMOU NT I NG
Perform the dismounting operations in the reverse order.
Tighten at the required moment, the exhaust manifold attachment nuts, observing the sequence
shown in the drawing.
vnx.su

ENGINE E7J-26212
12 - 7
F UEL M IXTURE
Air filter
2 3
5
1
4
FILTER ELEMENT REPLACEMENT
Dismount the attachment
screws (1) of the air filter cover.
Detach the attachment clamps (2).
Remove the cover and replace the filter element ( 3).
DISMOUNTING OF THE AIR FILTER
Dismount the air filter inlet hose
Dismount the four-attachment screws (4)
of the air filter on the cylinder head cover and
inlet manifold. Lift the air filter and disconnect from the
filter, the oil vapors re-aspiration hose ( 5).
REMOU NT I NG
Perform the dismounting operations in the
reverse order.
vnx.su

MOTEUR E7J-26213
FUEL SUPPLY
13 - 1
REMARK:
Only vehicle observing the de -pollution norm EURO 00 are equipped wi th shock
se nsor.
Supply int erruption
1
PURPOSE
To avoid the fire hazard due to the fuel losses, that may occur in case of an accident.
OPERATION
The hazard sensor ( 1) is placed in the engine compartment, being mounted on the left shock
absorber column.
In case of shock, the sensor ball l eaves its lodgement, t hus interrupting the electric c ircuit
between the control relay of the petrol electric fuel pump and the electric petrol pump.
HAZARD SENSOR RE-STARTING
The upper part of the hazard sensor is to be pushed to re-position the ball i nto its lodgement
and thus to re-start the sensor.
vnx.su