low beam DACIA SOLENZA 2004 Repair Manual

19
19 - 5
COOLING - EXHAUST - TANK
Radiator
SPECIAL TOOLS
MOT 1202 - 01
Pliers for elastic clips
MOT 453Hoses clamp
DISMOUNTIN G
Drain the air conditioning unit – for the ve-
hicles with air conditioning (see chapter 62” Fill-
ing –Draining the air conditioning circuit”). Disconnect the battery
Dismount the air inlet duct from the battery
screen. Detach from clips the oi l reservoir from the
battery screen, for the ve hicles equipped with
power steering. Clamp the hoses from radiator by means of
MOT 453 device.
Dismount the hoses from radiator by means
of the pliers for elastic clips MOT 1202-01 and
recover the cooling fluid.
Disconnect the engine fan connector (1).
Detach the wiring from clips ( 2) and (3).
Di sconnect the resistance connector ( 4), for
the vehicles with air conditioning. Carefully release the engine fan from the four
attachment clips ( 5) on the radiator- for the
ve hi c l e s e qui ppe d wi t h a i r c ondi t i oni ng,
c onsequently, the four screws ( 6) are
di sm ount e d, f or t he ve hi c l e s without a i r
conditioning.
The vehicles without air conditioning. Carefully remove the engine fan from the
sustaining p oints (7).
Dism oun t t he ra di a t or of f t he si de
attachment supports on the radiator upper
cross beam. Disconnect the two pipes from condenser.
Re l ease t he ra di ator from the lowe r
su p po r tin g buffers togeth er with the
condenser and recover the cooling fluid from
the radiator. Dismount t he condense r a ttachm ent
sc rews on the cooling radiator (for vehicles
with air conditioning).
For vehicles with air conditioning.
REMOU NT I NG
Mount the condenser on the new cooling
radiator (for vehicles with air conditioning).
M ount the radiator-condenser assembly
on the vehicle, by supporting it in the lower
elastic supports and attach it in the supports
of the radiator upper cross beam. Mount the engine fan assembly on the
sustaining supports (7) and attach it in the four
screws (for vehicles without air conditioning).
54
3
1
5
2
vnx.su

36
STEERING ASSEMBLY
36 - 3
Manual steering box
SPECIAL TOOLS
P. F. 476 Device for ball joints depressing
Wheels screws 7.5
St eering ball joint nut 4
St eering box attachment screws on crossbeam 5
Cardan joint connection screws with
column lower shaft 2.1
TIGHTENING MOMENTS (daNm)
Disconnect the battery.
Loosen the front wheels scr
ews.
Lift the vehicle by means of a two-column elevator.
Dismount the front wheels.
DISMOUNTIN G
In the engine compartment:
Cut the rubber bellows maintaining clip and push it towards cowl panel.
By means of the PF 476 device, depress the ball joints of the steering rods funnel from the
steering knuckle.
Dismo unt :
- connection screw between the cardan joint of the steering column lower shaft and the
steering rack gear shaft;
- steering box attachment screws on the crossbeam.
Detach the steering box assembled with the steering rods.
R EMOU NT I NG
Perform the dismounting operations in the reverse order, observing the required tightening
moments. In case a new steering box is mounted, the parallelism is obligatory to be adjusted, observing
the parallelism adjusting procedure described in chapter 31.
vnx.su

36
STEERING ASSEMBLY
36 - 14
Steering column
TIGHTENING MOMENTS (d aNm)
Steering wheel attachment screw 4.4
Steering column attachment screw
on driving post 2.1
Connection screw steering column lower
s haft- steering box gear s haft 2.1
DISMOUNTIN G
Disconnect the battery.
Dismount :
- steering wheel cover, clips attached;
- steering wheel attachme nt screw on the
steering column upper shaft, by means of a Torx
wrench (T50);
- steering wheel ( 1) not before ensuring
that that front wheels are straight line disposed
( steering at center point); -half-cases (2) and ( 3) attached t o the
steering column by means of three screws ( 4).
Disconnect the contacts:
- lights, windscreen wiper;
- anti-theft mechanism.
Loosen the screw (5) and dismount the
control under steeri ng wheel ( 6) from the
steering column upper shaft.
Di smount the side attachment screws ( 7)
of the upper part dashboard, by means of a
Torx wrench (T20), “L” shaped.
Dismount the attachment screws (8) of the
upper part dashboard from the l ower part
dashboard. Detach from clips in points ( 9) the upper
part dashboard.
Detach from clips the 3 attachment points
(10) of t he upper pa rt dashboard from the
windscreen lower cross-beam. Sw ing over the upper part dashboard
towards windscreen. For the vehicles equipped with radio:
-d ismount the radio from its support and
disconnect the connectors.
7
97
8
10
vnx.su

40
GENERAL
40 - 1
Lower structure composing elements
1. Front anti-shock cross member
2. Front cross beam
3. Longitudinal girder closing plate
4. Upper front longitudinal girder
5. Front longitudinal girder
6. Central cross member
7. Front floor
8. Threshold closing plate
9. Seat attachment structure
10. Tank front cross member 11 . Rear floor
12. Rear longitudinal girder
13. Tank towing hook
14. Rear anti-shock cross member
15. Rear extreme cross member
16. Tank rear cross member 1 7
11
9865432 131415161210
vnx.su

40
GENERAL
40 - 2
Upper structure composing elements
1.Headlam p support
2. Upper radiator cross bar
3. Front grill
4. Front wing lining
5. Front pillar lining
6. Front pillar
7. Roof belt
8. Middle pillar
9. Inner wheel passage
10. S i d e frame lining
11. S i d e panel
12. Fillin g cap door assemb ly
13. Rear lamp support
14. Rear plate assembly
15. Roof
16. W indscreen frame
17. Driving post cross beam
18. W indscreen lower cross bar
19. Climate control box
20. Climate control box central part
21. Cow l panel 123 4
5
6 8
17
10
15
16
18
19
20
21 14
13
12
11
97
vnx.su

57
57 - 3
INSIDE ACCESSORIES
Dismo unt :
-t wo side attachment screws (8) of the
upper part dashboard by means of a wrench T
20(“L” shape);
-screws (9) attaching the upper part
dashboard with the l ower part on the driving
post cross member, by means of a screwdriver
with T20 head. Detach from clips placed in points (10) the
upper part dashboard. Sw ing over the windscreen the upper part
dashboard and de tach from c lips poi nts (11)
of the windscreen lower cross beam. Detach from clips the radio from i ts sup-
port.
Disconnect the connectors and the ra dio
antenna (for the vehicle provided with radio-
cassettes player). Disconnect the central l ocking connector
(for the vehicle provided with central locking).
Take out the upper part dashboard from the
cockpit.
REMARK :
Dismounting of the upper part dash-
board, does not imply steering wheel dis-
mounting.
Disconn ect the anti-star ting bushing connec-
tor.
Detach from clips the anti-starting bushing
(12).
8
8
10
9
11
12
13
13 Dismount
the attachme nt screws (13) of the
instrument panel and disconnect the four con-
nectors.
Dashboard
vnx.su

57
57 - 5
INSIDE ACCESSORIES
REMOU NT I NG
Perform the dismounting operations in the reverse order, taking into consideration the follow-
ing recommendations:
-ensure that steering is at middle point (wheels are in a direct line);
- mounting of the lower part dashboard is to be performed by guiding it on a centering part
placed on the driving post cross beam; -steering wheel must freely enter in grooves;
- check the operation of the dashboard instruments and switches.
AT T E N T I O N :
After each steering wheel dismounting, its attachment screw is to be replaced, ob-
s erving the required tightening moment of 4.4 daNm.
Dashboard
vnx.su

61
HEATING
61 - 5
123
Ve
ntilation-climate control air distributor (RACV)
DISMOUNTIN G
Disconnect the battery.
Dismount :
- dashboard (see chapter 57 “dash-
board”);
- central console;
- electric windows control connectors;
- front pillars coverings;
- driving post cross beam;
- climate control box protector;
- gas purge vessel;
- climate control box gasket;
- engine air filter;
- climate control box central part from
the eight attachment screws;
- attachment screws of the climate c on-
trol unit and release the climate control blower
after disconnecting it.
- RACV attachment screws (1) on the
climate control box.
Clamp t he two hoses from the heating ra-
diator by means of the MOT 453 device.
Disconnect then the fast couplings from the
RACV heating radiator, recovering the c ool-
ing fluid. Dismou nt then:
- acoustic plate ( 2);
- mixing a nd distribution fl aps control
cables attached on RACV. Release RACV (3).
REMOU NT I NG
Perform the dismounting operations in the
reverse order. Fill up the cooling fluid and perform the cool-
ing circuit purging (see chapter 19 “ Filling –
Purging cooling circuit”).
Check :
- good operation of the flaps cables;
- good attachment of t he air ducts.
The require d tightening moment of t he
RACV attachment screws (1) on the climate
control box is of 0,6 daNm.
vnx.su

80
BATTERY - FRONT HEADLIGHTS
80 - 9
MEETING LIGHTS ADJUSTMENT (LOW BEAM)This is performed by acting upon the V screw
(vertically plane adjustment) or H (horizontally
p lane adjustment). By screwing, the lighting beam
is ”lowering” and by unscrewing is “ascending”. Check if the l ighted area is centered on the
vertical axis and if the optical separation at 15°
coincide with the headlamp lighting. An error of
1 cm is admissible. A lighting beam displaced towards left has
the aspect shown in (p icture a) and a lighting
beam displaced towards right has the aspect
shown in (picture b )
ROAD LIGHTS ADJUSTMENT (LONG BEAM)
Check the position to c oincide with the
adjustment pe rformed for low beam and with
the lighting beam distributed between the two
vertical lines on the panel
When checking the long beam, the lighting
center of t he ellipse, must be l ocated on t he
cross marking the screen center. If a m ajor de viation c ompared with t he low be am i s noticed, i t is re commended t he bul b
replacement, this one being in most of the cases, responsible for such defect.
Headlamps adjustment
H
V
figura a figura b
vnx.su

81
INSIDE AND REAR LIGHTING
81 - 5
Bulbs
BULBS
Headlamps High/low beam lights Bulb H4, 12V-60/55W Parking lights Bulb W5W, 12 V-5W
Front turning lamp Bulb PY21W, 12V-21W (colored)
F og projectors Halogen bulb H11, 12V-55W
Rear Parking, stop lights Bulb AB1, 12V-21/5W
lamps Turning lights Bulb PY21W, 12V-21W Rear fog lamp and reverse driving Bulb P21W 12V/21W
Rear side signalin g lamps Bulb WY5W 12V-5W
Ceiling lamp Bulb C5W, 12V-5W
License plate lamp Bulb W 5W, 12V-5W
Additional STOP lamp Bulb C21W, 12V/21W Sv8,5
Instrument panel Bulb12V, 2W (brown holder)
Bulb 12V, 1,2W (black holder)
Climate control panel Bulb 12V, 1,2 W
(black holder
vnx.su