spark plugs replace DACIA SOLENZA 2004 Repair Manual

IGNITION AND INJECTION
17
17 - 52
RECOMMENDATIONS
Diagnostic – Failures interpretation
DF 109
DF 110
P RESENT
OR
ME MO RIZEDPOLLUTED COMBUSTION MISFIRE
DESTRUCTIVE COMBUSTION MISFIRE
St ate ET014 : Recognition of the cylinder 1 must be active, in order to
i dentify each cylinder.
ET093 : combustion misfire on cylinder 1
ET094 : combustion misfire on cylinder 2
ET095 : combustion misfire on cylinder 3
ET096 : combustion misfire on cylinder 4
These w ill provide information regarding failure cause and location.
In this situation, the problem is probably due to an element that can act
only on one cylinder:
- Problem at injector
A cylinder is declared - Problem at spark plug
damaged : ET093 or ET094 - Problem at high voltage cable.
or ET095 or ET096. Before replacement, try the spark plug or cable changing to anothe r
cylinder.
Cy linders 1 and 4 or In this cylinders 2 and 3 declared situation, the proble m is probably
damaged : ET093 and ET 0 96 due to an eleme nt that can act only this pair of cylinders:
or ET094 and ET095. - Problem at ignition coil, at the high voltage part. - Problem at ignition coil, at the control part
In this situation, the problem is probably due to an element tha t can
F our cylinders declared act only on all cylinders:
damaged : ET093 and -Problem at fuel filter
ET094 or ET095 and ET096. -Problem at fuel pump
-Problem on in use fuel type
-Problem of in use spark plugs
In case by using this method the problem is not solved, cons ult the fail ures diagnostic DF109 / DF
1 10 CONTINUA TION
Ensure that all failures are solved. Erase all memorized failures.
There is no need to erase the “adaptive values” memoriz ed by the injection computer.
In order to check the correct reparation of the system, the following conditions must be
AF TER accomplished:
REPARATION - No more electrical failures;
- All “adaptive values” to be memorized by the injection computer;
- Warm engine (minimum 75°C);
- Run at idling, all consumers being in use for 20 minutes (1 minute DF110);
- If the failure is again occurring, repeat the dia gnostic.
vnx.su

IGNITION AND INJECTION
17
17 - 60
Va l ve potentiometer resistance Track = 1200 Ω ± 20 %
Slider = < 1050 Ω
Idling regulator resistance at 25°C= 53 Ω ± 10%
Ignition coil resistance Primary= 0.5 Ω ± 5 %
Se condary = 7200 Ω ± 10 %
Injector ’s resistance at – 40°C= 11.1 Ω
at 20C = 14.5 Ω ± 5%
at 120°C =20.6 Ω
Se nsor atmospheric pressure r esistance =50 kΩ
Upstream oxygen sensor heating resistance
For engines E7J-260-MA and E7 J-262 MB at 23°C = 6 ± 1Ω
Downstream oxygen sensor heating resistance for engines
E7J-260-MB, E7J-262-MB or upstream
for engine E7J-262-MB at 23°C= 3.3
+0.7 Ω
RPM sensor resistance at 23°C = 200 - 270 Ω
C anister purging valve resistance at 23°C = 26 Ω ± 7 %
Te m perature ( °C ) -40 -10 25 50 80 110 120
Air tempe ratur e se nsor 50000 9500 2051 810 309 135 105
Resist ance (ohms) ± 14 % ± 10 % ± 6 % ± 6 % ± 6 % ± 6 % ± 7 %
Water temperature sensor 75780 12460 2252 811 282 115 88
Resist ance (ohms) ± 9 % ± 9 % ± 5 % ± 5 % ± 3 % ± 2 % ± 2 %
Ignition system checking:
C heck the condition, insulation and continuity of the high voltage cables.
R eplace them if necessary.
C heck the condition and correct tightening of the ignition spark plugs and if the spark plugs are corresponding
with the recommended ones.
R eplace them if necessary.
C heck the condition of the ignition coil connectors.
Replace if necessa ry.
C heck the condition and the primary and secondary resistance values of the ignition coil.
R eplace if necessary
C heck the coils supply:
Pr esence of the +12 volts supply (contact set on).
C heck the ele ctric routing between the coil and the actuators relay.
M end if necessary.
Diagnostic – Help
-0. 3
vnx.su