ECU DACIA SUPERNOVA 2004 User Guide

82A
HORN - ENGINE IMMOBILISER
82A - 11
A.
ECU DECODER REPLACEMENT PROCEDURE AND ANTI STARTING
CODE MEMORISING
The new E.C.U. decoder is always not coded. After its mounting on the vehicle it is necessary
that this one is memorising the anti starting code in order to be operational.
NOTE
If only the E.C.U. decoder i s replaced, there i s no need of an i ntervention to t he
E.C.U. injection (injection computer), which will keep the old anti starting code.
AT TENT ION
After the E.C.U. de coder memorised the anti starting c ode, this code cannot be erased
or replaced with another one.
In order t o perform this procedure, one of the keys of t he ve hicle and the CLIP tester are
needed. Perform as follows: 1. Connect the CLIP tester to the diagnostic socket and to the battery (or the lighter
socket) of the vehicle. 2. Read the configuration of the old E.C.U. decoder in the following way, before dismounting
it from the vehicle:
- select t he type “SUPERNOVA” and the “050” equipping level;
- enter the menu “ COMPUTER TEST” then choose “ ANTI STARTING”
- access “COMMAND MODE” then “CONFIGURATIONS READING”
- note the configurations found : petrol/d iesel, programming with 1 or 2 keys, ceiling delay,
the type of the doors’ blocking switch (CPE), etc.;
3. Get back to the m enu “TEST COMPUTERS”
4. Remove the old E .C.U. decoder and replace it with a new one, the contact being off.
5. Enter the menu “ANTI STARTING”, then select “ STATE LIST”. If the E.C.U. decoder
is new, you must find the following states:
18G FIRST CYCLE MEMORISING………………........................ ACTIVE
19G NOT PERFORMED KEY PROGRAMMING……………….. ACTIVE
19D UNLOCKED KEY PROGRAMMING………………............. ACTIVE
OBSERVAT ION
If the states 19G and 19D are not “ACTIVE” this means the E.C.U. decoder has
been already used, so it isn’t new and cannot memorise another anti starting code.
Access the menu “COMMAND MODE” and then “CONFIGURA TION”, where you will
configure the new E.C.U. decoder in the same way as the old one: petrol, 1 key, ceiling delay,
impulsion doors blocking switch, etc. selecting one by one these configurations, which you’ll
validate with “CLICK” on the blue button on right top of the screen. PROCEDURES
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 16
D. SIMPLE S
YNCHRONISED PROCEDURE
This procedure allows the synchronisation of a RF remote control with E.C.U. decoder and
is to be applied in the following situations:
- the RF remote control c ode is no longer i n the range of the E.C.U. decoder re ception,
because of consecutive pushing over a 1000 time on the RF remote control button.;
- the replacement of the E.C.U. decoder with a new one;
- the replacement of the RF remote control if the E.C.U. decoder is new (E.C.U. decoder
replacement plus a RF key.)
The following operations will be performed: - take off t he contact
- push and maintain like that for about 5 seconds, the doors locking switch located on the
dashboard ; the doors actuators are performing a closing/opening course.
- during the next 10 seconds, confirmed by the permanent lightening of the anti starting
system indicator, push twice the RF remote control button; the doors actuators are performing a
closing/o pening course.
- the procedure of synchronisation is finished; check the blocking/ unlocking by pushing
the RF remote control.
OBSERVAT ION
Duri ng those 10 seconds you can visualise by means of the CLIP tester the state 17G
“THE PROGRAMMING IN PROGRESS OR THE TIR/TRF
RESYNCHRONISATION” which must be ACTIVE.
E. SPECIFIC SYNCHRONISED PROCEDURE
This procedure is used for the synchronisation of the second RF key with E .C.U. decoder
and will be performed as follows:
- connect the CLIP tester to the diagnostic socket and the battery (or the lighter socket) of
the vehicle. - select the vehicle type “SUPERNOVA” and the “050” equipping level;
- select the m enu “ COMPUTERS TEST” then “ ANTI STARTING”
- enter the m enu “COMMAND MODE” and select “CONFIGURATION”
- validate the command “ PROGRAMMI NG THE SECOND TIR / TRF KEY” launching
the command from the blue button situated on the right top of the screen; the doors actuators are
performing a closing/opening course.
- during the next 10 seconds, confirmed by the permanent lightening of the anti starting
system, push twice the RF remote control button; the doors will block and then unlock and the
anti starting indicator will t urn off. The second remote control is now synchronised. Check the
blocking/ unlocking by pushing the RF remote control. PROCEDURES
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 18
If the states
remain unchanged, check the following:
- electric connections of the decoding bushing
- the electric connections between the E.C.U. decoder and the decoding bushing
- the tension of the battery must have more than 8V when the starter is activated.
If all these are conformable, proceed to the replacement of the decoding bushing, and then
check again the a .m. states.
II. SOLVING MODE
When an electric ke y head (or both) is damaged, order (Info TECH LINE 0248/213766) a
new set of two electronic heads, subject to the vehicle type, as follows: TRF key head set – item no. 6001 543 684, 1 set, for DSN equipped with
anti intrusion (CLIMA or RAPSODIE)
TR-TRF key head set – item no. 6001 544 452, 1 set, for DSN without anti
intrusion (CLIMA or RAPSODIE)
TR key head set – item no. 6001 543 683, 1 set, for DSN EUROPA
Send to Tech Line (0248 213766), the chassis series no, the anti starting code of the damaged
key heads, the a nti starting code of the ne w key heads, and they will sent at their turn, to the
service center, the repairing code (taking into account that this code has a special regime). Additionally , there are necessary the new key heads, the E.C.U. decoder (obligatory TRF, if
the vehicle is equipped with central locking), the repairing code of the computer; proceed then to
the replacemen t of these items performing the following operation:
A) Replacement- c hecking electronic key heads :
Replace t he damaged key heads with the new ones (the metal insertions remain the same),
then by means of the CLIP tester, selecting COMPUTER TEST- ANTI STARTING- STATE
LIST, check following states with both keys:
If the states are in the following configuration, when setting the contact on, consecutively with
both keys:
ANTI STARTING……………………………………………..........ACTIVE
RECEIVED KEY CODE………………………………………….. ACTIVE
ACCEPTED KEY CODE…………………………………………PASSIVE DIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 24
4. FAILURE: MISSING SIGNAL ON TH E CODED LINE E.C.U. DECODER-
C
OMPUTER INJECTION
RECOMMENDATION
Check the continuity and the isolation related to the ground and + 12 V of the wiring between
the E.C.U. decoder PinA6 pin58 i njection computer.
Fix it if necessary.
S et the c ontact on and perform the detection test by the CLIP tester at pi n A 6 of the ECU
decoder.
Are there any impulses?
YES
NO Replace the injection
computer.
Replace the E .C.U. decoder.
Remove the memorised failure by means of the CLIP tester.
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
DIAGNOSTIC
vnx.su

82B
HORN - ENGINE IMMOBILISER
82B - 41
GENERALITIES
DESCRIPTION
The a nti intrusion system has t he purpose of peripheral prot ection of the ve hicle a nd the
volumetric protecti on of the passengers compartment (cockpit) and has the following components:
The ECU anti intrusion (1) is located under the central console, being attached under the
climate control unit and receives information from the volumetric sensors and from the contacts
of: front doors, engine hood and tail hatchback.
In case of an intrusion into the vehicle, when the system is activated, ECU will start t he siren
combined with intermittent lightening of the turning lamps.
The volumetric sensors (2) are fixed on the upholstery of the left and right upper part of the
pillars. After the activation of the anti intrusion system with the remote control, the sensors c an
supply information to the ECU concerning the interior volume of the cockpit, which, in case of its
modification will produce the siren starting and the intermittent lightening of the turning lamps.
The siren (3) is fixed on a frame, being located in the climate control unit and it is controlled by
the ECU anti intrusion.
The intrusion LED indicator (4) is located on the dashboard, on the left side and it indicates if
the system is activated or not and in case of an aggression on the vehicle, the indicator will show
the type of aggression.
The contacts of the front and rear doors (5), of the e ngine hood (6) a nd of the hatchback (7)
are supplying information concerning their opening, to the ECU anti intrusion, when the system is
activated.
1 3
6
4
7
5
2
vnx.su

82B
HORN - ENGINE IMMOBILISER
82B - 43
THE PIN CODE
The PIN code is formed of four figures and it can be used only for deactivating the anti intrusion
s ystem, if this operation can not be performed by pushing the deactivating button from the RF
remote control of the vehicle. For introducing the PIN code, perform as follows:-set on the contact key in the M position and take it off it for three times in seven seconds,
after which the anti intrusion LED indicator will switch on for three seconds; -set on the contact again on the M position and maintain it until the number of the L ED
blinks is e qual with the first figure of the PIN code, then take off the contact; -set on the contact in the M position and maintain it until the number of LED blinks is equal
w ith the second figure of the PIN code, then take off the contact;
-perform the above mentioned method in order to introduce the third and the fourth figure
of the PIN code;
-after that, the system is deactivated and the siren stops automatically;
- set on the contact again – the anti LED indicator must switch on, confirming in this way
that the c orrect introduction of the PIN code.
AT TENT ION
If it i s necessary the checking of the PIN code, t his will be pe rformed
only after al least 20 seconds have passed, since the anti intrusion ECU has been
connected to the vehicle’s wiring or since the connecting of t he vehicle’s battery.
The COBRA anti intrusion system can operate in t hree different modes (2,3 or 4).
For the Super Nova vehicles, the system has been programmed to work in the second operation
mode. If by mistake the PIN code was introduced in less than 20 seconds since the battery
connecting or since connecting the anti intrusion ECU, this can involve the change of the operation
way of the system, which will generate errors during the operation. There is, although, the possibility
of reprogramming the correct operation way (type 2) and in this purpose, perform the following
operations : - disconnect and then reconnect the anti intrusion ECU; when connecting the anti intrusion
ECU the anti intrusion LED indicator will switch on once, confirming the correct connecting;
-af ter at least 5 seconds from the previous operation, but no more than 20 second from it,
perform the following operation s:
-s et on the contact key in the M position for three times and then release it;
- the anti intrusion LED indicator will switch on for three seconds and then will switch off;
- set on again the contact key in the “M” position and maintain it, counting two blinks of the
anti intrusion LED indicator, then take off the contact;
- the LED indicator will blink for two times in two series, confirming in this way the proper
performance of the previous operations;
press the doors locking button of the dashboard, in order to lock and unlock the doors; the anti
intrusion LED indicator must not blink;
vnx.su

82B
HORN - ENGINE IMMOBILISER
82B - 46
AT TENT ION
Checking t he wiring c ontinuity between the components of the anti intrusion
sy stem shall be performed only after disconnecting the anti intrusion ECU and the
siren.
CHARACTERISTICS
- nominal supply tension ……………………………………… 12 V after contact
- operation tension …………………………………………..9 –16 V after c ontact
- consumption at 12 V after contact:
- on deactivated state ………………………………………….< 8mA
- on activated state ……………………………………………...\
< 13mA
- operation t emperature anti i ntrusion E CU …………………- 40 +85º C
- operation tempera ture of siren ………………………………- 40 +85º C
acoustic power …………………………………………………> 118 dB (A) from a distance
of 1 meter
FUNCTIONAL CHECKING OF THE SYSTEM
vnx.su

82B
HORN - ENGINE IMMOBILISER
82B - 51
If after a complete checking of the anti intrusion system,
the replacement of the E.C.U. anti
intrusion is required, proceed as follows:
- remove from the central console the tape recorder’s frame and the tape recorder pulling
backward but without disconnecting the tape recorder from the vehicle’s wiring;
- dismount by detaching the aeration grill located on the right side of the central console ;
- dismount the t wo screws attaching t he E CU support i n t he ri ght side of the climate
control unit;
- take off the anti intrusion ECU together with its support through the central zone of the
central console; - disconnect the 24 ways connector from the anti intrusion ECU proceeding as follows:
remove towards exterior the two blocking clips of the connector and then carefully pull out the
connector; - dismount carefully the two way connector from the anti intrusion ECU;
- dismount the two screw attaching the anti intrusion ECU on its support;
- proceed the in reverse order of the dismounting;
- check the proper operation of the anti intrusion system. DISMOUNTING – REMOUNTING
OF THE ANTI INTRUSION ECU
vnx.su

85
WINDSCR EEN WIPERS
85-1
DISMOUNTING-REMOUNTING OF TH E WINDSCREEN
WIPER MECHANISM
The windscreen wiper mechanism is mounted into the climate control box. This one, and his
components too, are in the next detailed drawing.
DISMOUNTING Disconnect the battery.
Release the protectors (A) from the axles.
Di smount the attachment nut ( B) of the
windscreen wiper mechanism’s arms and blades.
Dismount the attachment nut (C) of the axles from the windscreen’s lower frame; recuperate
the ruber gaskets and retaining washers.
Disconnect the wirring connectors from the windscreen wiper electric motor.
Dismount the mechanism’s attachment screw on the lower traverser windscreen.
Get off the mechanism.
REMOUNTING
Perform the dismounting operations in the reverse order.
NOTE:
When mounting the windscreen wiper mechanism’s arms the windscreen wiper
electric motor will be aligned in“stopped at fix point”.
WINDSCREEN WIPER MECHANISM
vnx.su

89A
ELECTRICAL DIAGRAMS
89A - 6
PA
RTICULARITIES REGARDING THE CONNECTORS
DISCONNECTING METHOD
Because this vehicle is equipped with electronics systems controlling and checking different
functions, it is necessary the execution of the electric connection by means of some connectors
provided with securing de vices after coupling performing. Due t o this reason, i n c ase t heir
disconnecting is necessary, proceed observing the following observations:
- connectors for: ignition coil (pos.1), canister purging valve (pos.2), AC pressure sensor (pos.3),
atmospheric pre ssure sensor(pos.4), siren(pos.4), step-by-step engine (pos.5), valve potentiometer
(p os.6), cooling blower (pos.7) are to be disconnected after easy pulling the locking clamp in the
di rection shown by the arrow.
- the connectors for: RPM sensor (pos.8), front hood contact (pos.9) are to be disconnected
after easy pulling the locking clamp (A) in the arrow direction, for unlocking.
pos. 8
A
pos. 9
A
pos. 1pos. 2pos. 3
pos. 5 pos. 6
pos. 7pos. 4
C
B
A
pos.10
GENERALITIES
vnx.su