gearbox DACIA SUPERNOVA 2004 User Guide

ENGINE E7J-A-2/6010
10 - 3
ENGINE AND LOWER ENGINE UNITS
MOTOR-PROPELLING GROUP
Di sconnect the wiring c onnector from t he
reverse driving contact. The right-side planetary transmission is un-
coupled as follows:
-the brake-stirrup set is dismantled;
-disconnect the wire for the brake pads
wear indicator; -the t wo screws for fixing the shock-
absorber of the steering-swivel stand are taken
off;
The steering-swivel stand is tipped up and
the planetary t ransmission is taken out from
the planetary pinion of the gearbox;
The l eft-side planetary transm ission is un-
coupled as follows:
-the steering-swivel screw-nut is dis-
mantled; -t he scre ws for fi xi ng t he pl a neta ry
transmission on the gearbox a re taken off; -the brake-stirrup set is dismantled;
-the e lectric wire of the wear-and-abra -
sion light-i ndicator is taken off; -the t wo screws for fixing the shock-
absorber of the steering-swivel stand are taken
off; -the steeri ng-swivel stand is t ipped up
and the planetary tra nsmission is taken out; The fuse-box in the engine compartment
is dismantled.The following are disconnected: -connector 1 from the UCE injection
(pull flap 2, then disconnect);
-the front cabling of the engine;
-the connector of t he shock-sensor;
-the ventilator connector;
-the mass wire on the gearbox.
The battery protection screen is dis-
mantled.
The following are taken off:-the linking pipes coming from the ra -
diator, by using the pincers for elastic pipe-
collars MOT.1202-01B ;
-the linking pipes coming from the de-
gassing vessel, by using the pincers for elas-
tic pipe-collars MOT.1202-01B ;
-the pipes for a ir-conditioning coming
from the therm ostat stand and the water-pi pe;
12
vnx.su

ENGINE E7J-A-2/6010
10 - 4
ENGINE AND LOWER ENGINE UNITS
The following are uncoupled:-the end of acceleration cable 1 from
the command lever of t he clapper; it is then
extracted off m uff 2 in the stand;
-the mileage cable: the two clamps are
pressed, and the cable is extra cted; -t he ri ght -si de he a dlight adjust m ent
cable, which is then positioned by the car
bodywork;
-the l inking pipes c oming from t he c arbon
canister and the canister-draining valve; -the fue l supply pi pes (both t he going- and
the re turn one) from the i njection ra mp, by
using MOT.1311-06 ;
The scre w linking the gear- bar and t he
auxiliary connecting rod to the gearbox is
dismantled.
MOTOR-PROPELLING GROUP
-the hydra ulic command con duit of the
clutch; fastener 1 is taken out and supply pipe
2 is withdrawn in the dire ction shown by the
arrow.
vnx.su

ENGINE E7J-A-2/6010
10 - 5
ENGINE AND LOWER ENGINE UNITS
MOTOR-PROPELLING GROUP
The screw- nut of t he hyd ro- e l a st ic
buffer is taken off (right);
The Motor-Propelling set is taken out and
then placed on a stand.
Re- Mounting
The steps are taken in the re verse order (see dismantling / taking apart).
To do:
-the filling-up a nd the drainage of the cooling circuit (see Chapter “ Filling-up and
Dr aining”).
CAUTION! USE ONLY TYPE D A NTIFREEZE.
- filling-up the engine and the gearbox with oil;
- filling-up and draining the clutch hydraulic command circuit (see Chapter “Draining
of the clutch hydraulic command circuit”); The liquid to use is brake fluid type SAE J 1703, DOT 3, DOT 4.
The screws and the screw-nuts of the couple are fastened back.
When mounting, line up markings from hoses and related parts.
The Motor-Propelling set is upheld by
the two handles, by means of a m oving
lifting device (a mobile crane);
The four screws fixing the Motor-Propel-
ling set ba ttery stand are taken off, as well
as the screw-nut of t he elastic buffer;
vnx.su

ENGINE E7J-A-2/6010
10 - 7
ENGINE AND LOWER ENGINE UNITS
Rotation sensor 2 is taken off;
The electric connections of the start er are undone;
The start er is taken off;
Electric connector 1 of the backwards motion contactor is taken off;
The engine cabling fa stening to the gearbox is dismantled;
The screws and screw-nuts of the gearbox assembly are taken off; SEP
ARATION ENGINE - GEARBOX
RE -ASSEMBLY ENGINE - GEARBOX
The separa tion operations are executed in the re verse order;
The screws and screw-nuts are tightened onto the couple.
TIGHTENING COUPLES (daNm) Rota tion sensor 0,8
Screws of the starter 4,4
Fixing the gearbox onto the engine:
- screw-nuts M 10 4,4
- screws M 10 - 90 4,4
- screws M 10 - 35 2,1
SEPARA TION - DISMANTLING
vnx.su

ENGINE E7J-A-2/6010
10 - 37
ENGINE AND LOWER ENGINE UNITS
TIG H TENING CO UPL E S (daNm)
Screws for fixing at front of motor-propelling frame 6.2
Screws for fixing at back of motor-propelling fram 10.2
Lower crankcase screws 1
Screws for fixing steering wheel lower axis 1.4
Screws of wheel 7.5
Screw of the ball-and-socket joint 5.5
Screw-nut of the steering ball-and-socket joint 3.5
Screw for fixing anti-swing auxiliary connecting rod (on frame) 6.2
Screw for fixing anti-swing auxiliary connecting rod (on gearbox) 10.5
D
IS M O UNT ING
The c ar i s placed on a l ifting stand with
two columns; The battery i s disconnected;
The engine is emptied of oil;
The engine-shield is taken apart ;
To take apart :
-front wheels;
-screw-nut for fixing the lower steer-
ing wheel axis on the pinion of t he steer-
ing case; -the steering ball-and-socket joints
and the arm ball-and-socket joints; -side clearance devices;
-thermic protection screen;
-catalytic convert er;
-front bumper ba r;
-anti-swing auxiliary connecting rod.
The screws for fixing the motor-propelling
s et fra me are taken a part, and the frame is
lowered; The lower c rankcase is taken apart.
R
E-MOUNT ING
The lower c rankcase is cleaned.
A ca. 3 mm-thick girdl e of RHODERSEAL
5661 is applied, as in the adjoining drawing. Do not forget to replace the two cres-
cent-sha ped fitti ngs at the e nds of the
crankcase.
Mind that the relative displacement be-
tween the lower crankcase and the cylin-
d er crankcase, along the gearbox-assem-
b ly surface, should not exceed 0.3 mm.
LOWER CRANKCASE MOUNTED ON THE CAR
LOWER CRANKCASE
vnx.su

ENGINE E7J-A-2/6012
FUEL MIXTURE
CH ARACTERISTICS
ENGINE
Car Gearbox Ty p e Index Cylinder Stroke Cylinder
bore length volume
(mm) (mm) (cm3)
SupeRNova JH3-050 E7J A-2/60 75,8 77 1390 9,5/1
Check-ups in idle mood*
Motor Emisii poluan
i
Fuel
Type Index Mode CO(%) CO2(%) HC Lambda (minimum
(rot/min) (1) ppm l octanic number)
E7 J A-2/60 750+/50 0,5 14,5 100 0,97.. .. Unleaded petrol
max min max ....1,03 (CO95)
(1) at 2500 rot /min the CO value must be max. 0.30%;
* For water t emperature over 80
oC and after stabilizing at 2500 rot/mi n for 30
seconds; then turn ba ck into idle mode and the level of fumes is measured. The water-tempera ture a nd air-t emperature sensors are type NTC (negative
temperature coefficient), and the vari ation of their re sistance as to temperature
has the following evolution:
T (0C ) 0 20 40 80 90
A ir-T sensor
11970 - 7470 4045 - 3060 1600 - 1315 - -
R (Ohm)
Engine T 8000 - 67 00 3000 - 2600 1300 - 1100 300 - 270 215 -200
sensor
R (Ohm)
12 - 1
vnx.su

16E7J-A-2/60 ENGINE
16 - 6
ST ARTING AND CHARGING
DIS M O UNT ING
(in the air -conditioning variant)
The car is placed on a two-column lifting stand;
The electric connections are uncoupled from the battery;
The following are taken apart: -the top scre w of the alternator;
-the belt of the alternator;
The right-side front wheel of the car is taken apart;
The car is suspended;
The two screws fixing the shock-absorber on the steeri ng swivel stand are taken off;
The steeri ng swivel stand is lowered and the right-side planetary tra nsmission is taken
off the planetary pi nion of the gearbox; The electric conductors of the alternator a re disconnected;
The screw of the alternator is taken off;
The alterna tor is taken apart laterally past the right-side planetary tra nsmission.
R
E-MOUNT ING
The taking-apart opera tions are done in the reverse order;
The carrying belt of the alternator is stretched to obtain the mounting tension recom-
mended (263 Hz +/- 10% );
The position of the alternator i s blocked;
The engine is revolved thre e and a half cra nkshaft turns;
The reading end of the MOT. 1505 measuring device is placed in the measuring area;
The tension in the belt is measured;
It is checked whether t his fits into the mounting tension tolera nce; if not , the belt will be
str etched again until the re commended tension ( 263 Hz +/- 10%) is reached.
The i nspection and the adjustment of the belt are done with the engine at ambient
temperature .
Tighten at the require d moment, the alternator a ttachment screws :- screw M10 (lower attachment)-5 daNm
-screw M10 (upper attachment)-2.2 daNm.
Remark: Once dismounted, a belt is not to be remounted, but replaced.
AL TERNATOR
vnx.su

16E7J-A-2/60 ENGINE
16 - 8
ST ARTING AND CHARGING
DIS M O UNT ING
The car is put on a two-column lifting stand;
The battery of storage cells is disconnected;
The screw-nuts fixing the degassing vessel are taken apart.
The degassing vessel is re moved (without disconnecting the link conduits) to the fore
part of the car i n order to facilitate access to the screws fixing the starter; The screws fixing the command bar on the connecting rod of the gearbox are taken off
(the jack is retrieved);
The screws no. 1 fixing the start er are taken;
STA RTER
The car is suspended;
The electric connectors of the starter are disconnected;
The start er is taken out through the bottom of the engine compartment. R
E-MOUNT ING
The taking-apart opera tions are done in the reverse order.
The screws are tightened at a 4.4 daNm couple.
vnx.su

20
CLUTCH
The ge arbo x has a noise / rattle
The clutch pe dal pushed to the fullest:
-stopped car
-eng ine not running.
The comp lete return of the
clutch peda l is checked
The state of the
pedal is checked
The state of the hydraulic
ci rc uit, that of the emitting
cylinder and of the hydrau-
lic receiver, are checked
The state of the
clutch is checked
The fau lty parts
are replaced
The state of the hydraulic
circu it is checked and the
circu it is drained
The state of the
hydrau lic receiver is
checkedThe fa ulty parts
are replaced
The stroke of the
hydrau lic receiver
is checked
The state of the
clutch is checked
NON-CO NFORMING




CONFORMING

CONFORMING
CONFORMING

CONFORMING

NON-
CONFORMING
CONFORMING

NON-CONFORMING
D I A G N O STIC

CONFORMING
NON-CONFORMING
NON-
CONFORMING

The defect is looked
for at the level of the
gearbox
20 - 6
vnx.su

20
CLUTCH
Trepidation
(t he car starts “by fits”)
The sta te of the props
of the gearbox is checked
Oiled clutch, or clutch hav-
ing a beat
The fau lty parts are replaced.
The o rigin of the beat is elimi-
nated.
The pr ops are replaced and the tight-
ening of the gearbox fixing spots on
the engine is checked, and also the
fixing of the engine
Clutch pedal has a “creak”
The axis of the clutch
pedal is oiled
Pedal axis worn-out
The fau lty parts are replaced
NON-CONFORMING



NON-
CONFORMING

CONFORMING



D I A G N O STIC
20 - 8
vnx.su