wheel DACIA SUPERNOVA 2004 User Guide

ENGINE E7J-A-2/6010
10 - 1
ENGINE AND LOWER ENGINE UNITS
INGREDIENTS
TYPE
RHODORSEAL 5661
Loc tite FRENETANCH
Exhaust Pipe Paste
ORGANS
Lower ca sing, crankshaft bearing cap
Crankshaft pulley screws, flywheel
screws
Exhau st pipe sealing
IDENTIFICATION
Type / Mark Engine Gearbox
Cylinder
capa city
(cm
3) Cylinder
Bore
( mm) Stroke
( mm) Volumetric
Ratio
SupeRNova E7J
-A-2/60
JH3 - 050 1390 75,8 77 9,5/1
Id en tification is done by means of a plate located on the cylinder casing.
It includes:
A: type of engine
B: engine approval letter
D: identity RENAULT
E: index of engine
G: engine moun ting plant
F: engine ma nufacturing serial number
Loctite 518 Water-pump, thermostat stand, crank-
shaft closing end casing
Loc
tite AUTOFORM Flywheel face for mounting on crank-
shaft
INGR
EDIENTS
000 0 0 / 00
0 000000
A B D E
G F
E7J-260-MB
EURO 2
EURO 3
Engine o il DACIA OIL EXTRA
10 W40; AP I SJ/CF Engine o
iled
Decapjoint Cylinder head gasket surface cleaning
Depollution Norm
vnx.su

ENGINE E7J-A-2/6010
10 - 2
ENGINE AND LOWER ENGINE UNITS
MOTOR-PROPELLING GROUP
Di smounting and re -mounting the motor-propelling group i s done at the upper pa rt of the
engine compart ment by means of a moving lift ing device. C
OUPLES FO R S
CRE W-FIXING (daNm)
Screws for fixing right-side stand on engine 6,2
Hydro- elastic buffer attachment nut 3,7
Screw-nut for left-side elastic buffer 6,2
Wheel sc rews 7,5
Screws for fixing motor-propelling group-battery stand 2,1
Screw-nut for fixing small connecting rod on steering traverse 6,2
Screw for fixing anti-swing connecting rod on gearbox case 10,5
Control bars attachment screw on gearbox connecting rods 2,7
Car is placed on a lift-stand with two columns;
The fol lowing are taken down: battery, air-
filter case, engine bonnet, front wheels; Oxygen probe connector is taken off;
Dismantle: therm ic protection screen, cata-
lytic convert er on the exhaust collector;
DIS M O UNT ING
The fol lowing are eva cuated:
-the cooling circuit at the bottom par t
of the radiator ;
-the oil in the gearbox ;
-the oil in the engine, if necessary.
The fol lowi ng are ta ken dow n: -engine shield;
-the screws that fasten the catalyti c
converter on the stand;
-the pipe-collar between the catalyti c
converter and the trigger ;
-the catalytic converter;
-the anti-swing auxiliary connectin g
rod.
vnx.su

ENGINE E7J-A-2/6010
10 - 13
ENGINE AND LOWER ENGINE UNITS
PISTONS
The bol t i s steady i n the connecting rod
and loose in the piston.
Dir ection of mounting: with the arrow to-
wa rds the flywheel.
There are three classes of association with
the jacket.
Markings on the pistons:
1 - arrow towards the flywheel
2 - class of piston (A-B-C)
3 - line-up marks used by the supplier.
Piston
line-up Piston diameter (m m) Jacket diameter (m m)
marks
A 75,765 - 75,775
* 75,8 - 75,75,81*
B 75,775 - 75,785* 75,81 - 75,82*
C 75,785 - 75,795 75,82 - 75,83
The piston di ameter i s measured for t he
mark:
A = 46 mm. * - the respective values are not included in the classes
CH
ARASTERISTICS
vnx.su

ENGINE E7J-A-2/6010
10 - 16
ENGINE AND LOWER ENGINE UNITS
The amount of oil to be introduced in the
engine is 2.7 liters - without replacing the oi l-
filter - or 2.9 liters, after re placing the filter.
The minimum oil pre ssure at 80
o is:
-in the idle mode 1 bar
-at 4000 rot/min 3 bar
The oil pump belongs to the “gearwheel”
type. Take off the cap and a lso the clapper of
the oil-pump.
To check:
* play A (mm): - min. 0.110
- max. 0.294 * play B (mm):
-min. 0.02
- max. 0.86.
CAUTION!
P rotect the distribution and alternator belt in order to avoid water-
or cleaning substance projection on them.
OIL PUMP
* TO BE ADJUSTED TO TH E GAUGE
CH ARASTERISTICS
vnx.su

ENGINE E7J-A-2/6010
10 - 18
ENGINE AND LOWER ENGINE UNITS
DIS M OUNT ING
The oil and the cooling fluid are empties.
To be taken off:
-the electric connections;
-the alterna tor and its belt;
-the pulley of the crankshaft (in order to do that, t he flywheel is bl ocked with the
MOT 582 device)
-the protection cap of t he distri bution belt RE
CO VERY ENGINE
CYLINDER HEAD
vnx.su

ENGINE E7J-A-2/6010
10 - 27
ENGINE AND LOWER ENGINE UNITS
The arrow marke d by the end of the
piston must be directed towards the
flywheel. The conne c ting rods d o not ha ve a
mounting dire ction, but the spurs of t he
s emi-bushes will be positioned on the same
side. For the assembly of t he piston and the
connecting rod, the following directions
will be observe d:
-jack B13 is set onto the stand and t he pis-
ton (with the arrow pointing upwards) is
fixed on the jack;
-the centri ng device and the axis of
the piston are oiled with motor oil; -the free sliding of the piston axis is
checked, as well as the positioning of t he
piston. When the base of the connecting rod
reaches the needed tempera ture (ca. 250
o),
the speedy mounting of the pisto n axis
should be done in the following manner: -the centring guide is introduc ed in
the piston; -the rod i s positioned in the piston;
-the piston axis is pressed up to the
end. It should be checked if the piston axis
remains retracted as to the outer diameter
of the piston for any position of the con-
necting rod in the piston. The “ rod-piston-ring” sets a re mounted
in the cylinder jackets by using the
mounting jack. The waterti ght - se a l i ng f i t t i ngs a re
mounted onto the cylinder j ackets.
THE CYLINDER CRANKCASE
The rings are mounted: -the oiling ring;
-the watertight-sealing ring (with the
“TOP” mark pointing upwards); -the compression ring (with the “TOP”
mark pointing upwards). The slits of the ri ngs being adjusted, they
shall never be altered; they are oiled and the
rings are positioned; the slit of t he oi ling ring
will be placed opposite a full part of its channel.
RE CO VERY ENGINE
vnx.su

ENGINE E7J-A-2/6010
10 - 30
ENGINE AND LOWER ENGINE UNITS
Mount the lower c asing and tighten the scre ws at a moment of 1daNm.
The watertight-sealing is done with RHODORSEAL 5661; girdle D must be 3 mm thick.
Do not forget to replace the two crescent-shaped fittings (in the A are a) with new
ones.
-the fl ywheel: beforehand oil t he face for t he pl acing of the flywheel on the crank-
s haft, using LOCTITE AUTOFORM; apply on the screws one drop of LOCTITE
FRENETANCH and tighten them at 5 - 5.5 daNm, after having blocked the flywheel
by means of the cogged sector MOT 582.
-the clutch (be cautious about the centring): scre ws are tightened at 2 daNm;
-the water-pump (the watertight-sealing is done with LOCTITE 518, the H girdle
must be of 0.6 - 1 mm). The screws are tightened at a couple of 1 - 2 daNm.
LOWER CASE
RE-MOUNTING
THIS OPERATION IS ALSO VALID IN CASE THE CRANKCASE IS RE- MOUNTED ON THE CAR (SEE PAGE 10-36)
RECO VERY ENGINE
vnx.su

ENGINE E7J-A-2/6010
10 - 37
ENGINE AND LOWER ENGINE UNITS
TIG H TENING CO UPL E S (daNm)
Screws for fixing at front of motor-propelling frame 6.2
Screws for fixing at back of motor-propelling fram 10.2
Lower crankcase screws 1
Screws for fixing steering wheel lower axis 1.4
Screws of wheel 7.5
Screw of the ball-and-socket joint 5.5
Screw-nut of the steering ball-and-socket joint 3.5
Screw for fixing anti-swing auxiliary connecting rod (on frame) 6.2
Screw for fixing anti-swing auxiliary connecting rod (on gearbox) 10.5
D
IS M O UNT ING
The c ar i s placed on a l ifting stand with
two columns; The battery i s disconnected;
The engine is emptied of oil;
The engine-shield is taken apart ;
To take apart :
-front wheels;
-screw-nut for fixing the lower steer-
ing wheel axis on the pinion of t he steer-
ing case; -the steering ball-and-socket joints
and the arm ball-and-socket joints; -side clearance devices;
-thermic protection screen;
-catalytic convert er;
-front bumper ba r;
-anti-swing auxiliary connecting rod.
The screws for fixing the motor-propelling
s et fra me are taken a part, and the frame is
lowered; The lower c rankcase is taken apart.
R
E-MOUNT ING
The lower c rankcase is cleaned.
A ca. 3 mm-thick girdl e of RHODERSEAL
5661 is applied, as in the adjoining drawing. Do not forget to replace the two cres-
cent-sha ped fitti ngs at the e nds of the
crankcase.
Mind that the relative displacement be-
tween the lower crankcase and the cylin-
d er crankcase, along the gearbox-assem-
b ly surface, should not exceed 0.3 mm.
LOWER CRANKCASE MOUNTED ON THE CAR
LOWER CRANKCASE
vnx.su

ENGINE E7J-A-2/6010
10 - 39
ENGINE AND LOWER ENGINE UNITS
TIGHTENING COUPLES (daNm)
Screws for fixing combustion-head cap1
S crew-nut for stretching distribution belt runner/pulley 5
Screws and screw-nuts M 6 for water-pump 1
Screws and screw-nuts M 8 for water-pump 2.2
Screw of the crankshaft pulley 2+68
o+/-6o
Screw of cam-shaft pin 4.5
Screws of rocker-arm ramp 2.3
S crews of flywheel 5 - 5.5
Screws of oil-pump 2.5
Screws of oil-pump cap 1
Screws of bearing caps 2.5+43
o+/-6o
Screws of combustion-head 2+97o+/-2o
Screws of the exhaust gallery 2.5
Screws of the intake gallery 2.5
Sparking plugs 2.5 - 3
Screws of the oil-crankcase 1
Screws for rocker-arm adjustment 1.5
Emptying jack 2
S crews of the connecting rod caps 4.2
Oxygen probe 4.5
TIGHTENING COUPLES
vnx.su

ENGINE E7J-A-2/6011
UPPER AND FRONT ENGINE UNITS
Tightening couples (daNm)
Screws of wheels7.5
Screw of the crankshaft pulley 2+68
o+/-6o
S crew-nut of stretching runner 5
Screws right-side stand 6.2
Screw-nut hydroelastic buffer 3.7
DISMONTING
The car is placed on a lifting stand.
The fore part of the engine is proppe d
on the frame using the MOT.545 device.
The following are taken apart: -front right-side wheel;
-the right-side pendular suspension;
11 - 1 -the alterna tor belt;

-the carrying belt of the compressor
(AC) ;
-the pulley of the crankshaft and its hub;
-the carryi ng pulley of the compressor;
-the distri bution crankcases.
DIS TRIBUTION BELT
vnx.su