sensor DACIA SUPERNOVA 2004 Service Manual

82B
HORN - ENGINE IMMOBILISER
82B - 54
NOTE
If the dismounting / remounting of t he front doors or hatchback contacts,
check aft er that , the correct operation of the anti intrusion system.
LEFT SIDE VOLUME SENSOR REPLACEMENT
If sensor replacement is required, proceed as follows:
- take out carefully the sensor from its support by detaching from clips;
- dismount the attachment screw of the sensor support on the front left pillar upholstery.
- dismount the three attachment screws of the upper upholstery of the front left pillar and
carefully remove the upholstery;
- carefully disconnect the sensor connector from the vehicle’s wiring;
- mount the new volume sensor and its support performing the above mentioned operations
in reverse order, and then checking the proper operation of the anti intrusion system.
AT TENT ION
Be sure that the v olume sensor mounted on the l eft side has marked the
letter “T ” on the red colour collar.
Mo unt the volume sensor in such way, to be oriented towards the back of the vehicle,
parallel wi th the side windows.
RIGHT SIDE VOLUME SENSOR REPLACEMENT
If sensor replacement is required, proceed as follows:
- take out carefully the sensor from its support by detaching from clips;
- dismount the attachment screw of the sensor support on the front right pillar upholstery.
- dismount the three attachment screws of the upper upholstery of the front right pillar and
carefully remove the upholstery; - carefully disconnect the sensor connector from the vehicle’s wiring;
- mount the new volume sensor and its support performing the above mentioned operations
in reverse order, and then checking the proper operation of the anti intrusion system.
AT TENT ION
Be sure that the volume sensor mounted on the right side has marked t he l etter
“R” on the white colour collar. Mo unt the volume sensor in such way, to be oriented t owards the bac k of the v ehicle,
parallel wi th the side windows.
V OLUME SENSOR DISMOUNTING – REMOUNTING
vnx.su

83
INSTRUMENT PANEL
NOTE
Dismounting / re m ounting of t he spe e do c abl e, m ay be pe rform e d onl y aft e r
dismounting the instrument panel from the dashboard.
DISM OUNTING
Disconnect the battery;
Dismount the dashboard lower fairing;
Disconnect the RPM sensor connector;
Dismount the speedo cable from the gearbox;
Dismount the speedo cable from instrument panel back part, by detaching it from clips, pushing
in the direction of the A and B arrows, then extract it acting in t he direction of C arrow. Remove the speedo cable under the dashboard.
REMOUNTING
Perform the dismounting operations in the reverse order.
83-7
DISMOUNTING / REMOUNTING SPEEDOMETER CABLE ( FLEXIBLE SHAFT )
vnx.su

89A
ELECTRICAL DIAGRAMS
89A - 5
ATMOSPHERIC PESSURE SENSOR
Position Sectioning Destination

1 0,5 3DQDETONATION SE NSOR MASS

2 0,5 3S DETONATION INFO INJECTION COMPUTER
ENGINE WIRING B41
01
DETONATION SENSOR
11 12 13 2 5 3 4
6
14
7
8 9
10
88 - 07
15
1
1 2
3DQ 3S
X X
CY2AE M A
146
147 3GN 3F 3D
X X X
A B C
ZW3DT VE
GENERALITIES
vnx.su

89A
ELECTRICAL DIAGRAMS
89A - 6
PA
RTICULARITIES REGARDING THE CONNECTORS
DISCONNECTING METHOD
Because this vehicle is equipped with electronics systems controlling and checking different
functions, it is necessary the execution of the electric connection by means of some connectors
provided with securing de vices after coupling performing. Due t o this reason, i n c ase t heir
disconnecting is necessary, proceed observing the following observations:
- connectors for: ignition coil (pos.1), canister purging valve (pos.2), AC pressure sensor (pos.3),
atmospheric pre ssure sensor(pos.4), siren(pos.4), step-by-step engine (pos.5), valve potentiometer
(p os.6), cooling blower (pos.7) are to be disconnected after easy pulling the locking clamp in the
di rection shown by the arrow.
- the connectors for: RPM sensor (pos.8), front hood contact (pos.9) are to be disconnected
after easy pulling the locking clamp (A) in the arrow direction, for unlocking.
pos. 8
A
pos. 9
A
pos. 1pos. 2pos. 3
pos. 5 pos. 6
pos. 7pos. 4
C
B
A
pos.10
GENERALITIES
vnx.su

89A
ELECTRICAL DIAGRAMS
89A - 7
- the connector of the water temperature sensor (pos.10) shall be disconnected
as follows: push
the sensor connector in antipodes points, in the direction of the A and B arrows, achieving in this
way the unlocking of the ( C ) spur, then perform the disconnecting.
- the connectors of oil pressure contact (pos.11) and of the reverse driving contact shall be
disconnected as follows: push in antipodes points in the direction of the (A) and ( B) arrows, achieving
in this way the unlocking of the connector claw, then the connector may be disconnected by pulling
in the ( C) arrow direction.
- the connector of the choke sensor (pos.12) shall be unlocked by pushing the clamp in the (A)
arrow direction, then the connector disconnecting may be achieved.
- the injection computer (pos.13) – the unlocking is performed by acting upon the locking clamp
(A) in the (B) arrow direction, then lift the connector in the (C) arrow direction, achieving in this way
the computer disconnecting. For reconnecting, perform the disconnecting operations in the reverse
order.
pos . 11
A
B
C
pos . 12
A
pos.13B C
A
GENERALITIES
vnx.su

89A
ELECTRICAL DIAGRAMS
89A - 8
- the connector of the air temperature sensor (pos.14) and of the injectors (pos.14) – push the
locker (A) in the (B) arrow direction then the connector disconnecting may be achieved. The reconnecting of the a.m. connectors sha ll be performed after their correct positioning, followed
by their pushing till a “click” is he ard, that will confirm the firm and correct performing of the connecting.
The connecto r of the oxygen sensor, the coupling connections of the rear wiring to the vehicle
doors wiring, the connections between the doors actuators and the doors wiring are attached to the
car riage body by means of clamps (pos.15). To unlock the clamps maintaining these connectors on the
carriage body, disconnect these connectors, easy push the clamp terminal (I) in the (A) arrow direction
a nd move the connector in the (B) arrow direction, parallel cu the attachment surface on the clamp.
The a ttachment of the connector on the clamp is achieved, proceeding in the reverse order, then
the disconnecting may be performed.
The co nnections between front wiring, das hboard, rear and engine are attached by sliding in the
supports. Next, the disconnecting/reconnecting procedure of the front wiring-dashboard (pos.16) is
presented, which are attached on a support placed under the dashboard, left side:
-r em ove the connection form the support (A), by pulling it in the (B) arrow direction.
-push the (C)- locking spur, then the connections disconnecting may be achieved.
-a t reconnecting, push the two connectors till the correct connecting.
-p osition the connection in the (A) support guides, then push in the (D) arrow directions.
pos . 15
A
B
1
B
DA
C
pos . 16
pos . 14
BA
GENERALITIES
vnx.su

89A
ELECTRICAL DIAGRAMS
89A - 12
(until 01.06.2001)
21
101
102
103
104
105
107
113
120
121
122
123
124
125
128
137
138
139
140
141
145
146
147
149
155
156
160
163
165
168
171
172
173
175
176
177
180
181
184
185
188
189
190Right signalling anti-return diode
Electric lighter
Ashtr a y
Alternator
Anti-theft system
Acoustic alarm
Battery
Windscreen wiper timer
Injection computer (UCE)
Fog lights switch
Fog headlights switch
Door closing switch
Climate blower switch
Hazard switch
Rear window defrosting switch
Turning signalling relay
Right rear door actuator
Left rear door actuator
Left front door actuator
Right front door actuator
Windscreen wiper-washer switch
Detona tion sensor
Atmospheric pressure sensor
RPM s
ensor
Reverse driving contact
Handbrake contact
St op contact
Starte r
Trunk lighting lamp
Documents compartment lighting lamp
AC compressor clutch
Right rear lamp
Left rear lamp
Left fog lamp
Right fog headlight
Left fog headlight
Left front door contact
Right front door contact
Right front parking lamp
Left front parking lamp
Cooling motor fan
Right rear loud speaker
Left rear loud speakerRight front brake pad
Left front brake pad
Windscreen washing pump
Va l ve potentiometer
Diagnostic socket
Right headlamp
Left headlamp
Fog lamps relay
Fog headlights control relay
Cooling motor fan control relay
Fuel pump control relay
Actuators relay
Injection water temperature sensor
Instrument panel
V ehicle speed transducer
Right front turning lamp
Left front turning lamp
Cockpit fuse and relays box
Radio
Cooling motor fan and AC
Right side signalling lamp
Left side signalling lamp
Injection air temperature sensor
Rear window defrosting timer
Climate control lighting
AC starting button
Motor fan resistance ( f or AC)
Left front ceiling lamp
Right front ceiling lamp
Canister purging valve
UCE anti-intrusion
Engine hood contact
Siren
Vo l u metric sensor
AC relay ( on board)
UCE decoder
Hatchback contact
AC compressor clutch control relay
Engine compartment fuse and relays box
Climate control blower
STOP-S3 l amp
St ep-by-step engine
Anti-starting bushing
216
217
221
222
225
226
227
230
231
234
236
238
244
247
250
255
256
260
261
262
267
268
272
294
298
319
321
328
329
371
427
438
442
454
474
503
560
584
597
600
639
649
654
CODE COMPONENT DENOMINATIONCODE COMPONENT DENOMINATION
ELECTRIC COMPONENTS INDEX
vnx.su

89A
ELECTRICAL DIAGRAMS
89A - 13
191
192
193
194
195
196
199
205
209
210
212Cooling blower low speed control relay
Ignition coil
FLASH relay
Hatchback contact separation diode
Upstream oxygen sensor
C
hock sensor
Anti-intrusion indicator LED
Braking system ICP
AC pressure sensor (pressure controller)
Front ashtray lighting
Climate control blower control relay
700
778
857
871
887
927
993
109 1
120 2
133 5
142 8Right front door loud speaker
Left front door loud speaker
Injector 1
Injector 2
Injector 3
Injector 4
Fuel level transmitter and electric pump
Oil pressure contact
Lights, turning lights and horn switch
Electronic clock
Windscreen wiper motor
ELECTRIC COMPONENTS INDEX
vnx.su

89A
ELECTRICAL DIAGRAMS
89A - 16
Windscreen wiper timer
FLASH relay
Climate control lighting
AC starting button
AC relay ( on board)
Right front door actuator
Right rear door actuator
Right front door loud speaker
Right rear loudspeaker
Fuel level transmitt er and electric pump
Trunk lighting la mp
Left rear loud speaker
Left rear door actuator
Left fron t door actuator
Left fr ont door loud speaker
Right front door contact
Right volumetric sensor
Left vo lumetric sensor
Right front ceiling lamp
Hatchb ack contacts
Handbrake contact
Anti-starting bushing
Le ft front ceiling lamp
Anti-intrusion indicator LED
Left fron t door contact
UCE d ecoder
Siren
Vehicle speed transducer
Engine hood contact
Doors closing switch
UCE anti-intrusion
( until 01.06.2001)
Inje ctor 1
Inje ctor 2
Inje ctor 3
Inje ctor 4
Atmospheric pressure sensor
Detonation sensor
Starter
In jection air temperature sensor
Valve potentiometer
Step-by step engine
Alternator
Ignition c oil
Canister purging valve
AC pressure sensor(pressure controller)
Diagnostic socket
AC compressor clutch
Upstream oxygen sensor
Cooling blower and AC
Blower resistance for AC
Oil pressure contact
Injec tion computer
RPM sensor
Reverse driving contact
AC compressor clutch control relay (E)
Water temperature sensor
Blower lower speed control relay (B)
E ngine compartment fuse and relays box
Motor fan control relay ( C)
Fog headlamps control relay(A)
Fuel pump control relay (H)
Actuators relay(D)
Chock sensor
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32 33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
LOCATION OF ELECTRIC COUPLING ON THE VEHICLE
vnx.su

89A
ELECTRICAL DIAGRAMS
89A - 22
The fuse box placed in the engine compartment is attached in front of the left shock absorber
column and contains relays and fusible protecting the following electric circuits:
A.
for equipping E1, E2
( until 01.06.2001)
RELAY
RELAY TYPE
CONTROLLED
CIRCUIT
A
15A
Fog
headlamps
D
30A
Injector s, canister purging valve,
oxygen sensor heating
resistance, injection computer.
H
30A
F uel pump
Ignition coil
C
30A
C ooling blower
(vehicle without
AC)
FUSE
NUMB ER
F01
F02
F03
F04
F17 FUSE
TYPE
30A
25A
7,5A 5A
15A PROTECTED C IRCUIT
In jectors, oxygen sensor resistance heating, canister
purging valve, injection computer, fuel pump, ignition coil.
Cooling blower ( vehicles without AC)
Injection computer ( + DC)
In jection computer( (+IC)
Fog headlights
FUSE BOX FROM ENGINE COMPARTMENT
vnx.su