wheel DACIA SUPERNOVA 2004 Manual PDF

33
REAR BEARING ELEMENTS
SHOCK ABSORBER
TIGHTENING MOMENTS
Shock absorber inner attachment nut 8
Shock absorber upper attachment nut 1,45+/-0,3
NOTE
The storage of the shock absorbers in the
s pare part s shops i s made i n hori zontal
position.
In these conditions, the shock absorbers,
which are vertically functioning, may de-
st rike.
So, it is enough that before mounting on
the v ehicle, t o proceed on striking the shock
absorbe rs by al t ernat i ve movi ng up and
down of the shock absorber rod in vertical
position.
1. Upper attachment nuts
2. Protector
3. Upper buffer
4. Inner attachment screw.
DISMOUNTING
Remove the shock absorber prot ector (2).
Di smount the upper attachment scre ws (1) (through the trunk).
Loosen the scre ws of the wheel.
Di smount the wheel.
Lift the vehicle by means of an elevator and dismount the inner attachment scre w (4).
Di smount the shock absorber.
REMOUNTING
Pe rform in reverse order the dismounting operations.
Remount: - the shock absorber a t the lower side;
- the shock absorber a t the upper side.
Tighten the nuts at the re quired moment.
33 - 5
vnx.su

33
REAR BEARING ELEMENTS
SPRING
DISMOUNTING Place t he locking clamp of t he SUS 600
device in order to maintain the spring
compressed. Loosen the screws of the wheel on the side
where the dismounting is performed.
Dismount the wheel.
Di smount the shock absorber lower attach-
ment nut and screw. Push the axle and remove the spring.
REMOUNTING
Pe rform in reverse order the dismounting operations.
NOTE
M ake sure that springs of each axle have the same characteristics.
REAR SPRING
Coil diameter (mm) Length under load (mm)
F 14,3 230 +/- 10 / 330 daN
33 - 6
vnx.su

33
REAR BEARING ELEMENTS
BRAKE DRUM
The t wo brake drums having the same di ameter; t he rectifyi ng of one of t hem obligatory
implies the same opera tion for t he other one.
SPECIAL TOOLS
DISMOUNTING
Extract the plug out of the drum using the
extracting pliers RO441.
Release the hand bra ke, loosening the sec-
ondary cables in order t o allow the hand brake
lever re turn. Pass a screwdriver through the wheel at-
tachment whole from the drum and operate
on the brake lever sector loosening the its
gearing with the hand brake lever. Dismount:
- the steering knuckle nut and washer;
- the drum using PF600 extractor.
REMOUNTING
Clean the drum and the brake plate assembly by means of a cleaner (vacuum cleaner)
for brake. Place back:
- the drum;
- the steering knuckle washer and nut tightening them at the re quired moment;
- the drum plug.
A djust:
- the shoes by applying a repeated pressure to the brake pedal;
- hand brake ( see chapter 37-“Controls”).
DENOMINATION
CODE
Plug extracting pliers RO441
Dr um extractor PF600
TIGHTENING MOMENTS (daNm)
Wheel attachment screw 7.5
Steering knuckle nut16
33 - 7
vnx.su

33
REAR BEARING ELEMENTS
BRAKE CYLINDER
TIGHTENING MOMENTS (daNm)
Wheel attachment scre w 7.5
Rear wheel steeri ng knuckle nut 16
Pu rging screw 1
Brake rigid piping connection screw 1.5
DISMOUNTING
With the vehicle placed on an elevator
w ith two columns, dismount:
- the wheel;
- the drum plug;
- brake drum;
- upper spring of shoes return, using
pliers FR03.
Space the brake shoes.
Unscrew: - the rigid piping connection on the brake
cylinder by means of an open-end wrench; - the two attachment screws of the
brake cylinder on t he brake plate, loosen-
ing the connection. Check the condition of the shoes brake gas-
kets; if oi l tra ces are present, replace them.
REMOUNTING
Clean t he drums and the brake shoes as-
sembly by means of a cleaner (vacuum
cleaner) for brake. Perform in re verse order t he dismounting
operations. Purge the braking system (see chapter 38).
DEN
OMINATION CODE
Di smounting pliers for shoes return spring FR03
Plug extractor pliers RO441
SPECIAL TOOLS
33 - 8
vnx.su

33
REAR BEARING ELEMENTS
BRAKE CYLINDER
A djust:
- the shoes, by applying a repeated pressure to the brake pedal;
- the rear axle bearing clearance.
Mount the wheel.
Lower the vehicle from the elevator.
Pu rge the braking system (see chapter 38).
Adjust the hand bra ke.
REPAIRING
DISMOUNTING
Di smount the bra ke cylinder off the vehicle;
Di smount:
- the purging screw;
- the protection bellows;
- the Ö22 pistons assembled with the pressure ga skets.
Check the condition of the cylinder boring, any trace of wear, oxidation or scratches
implies the re placement of the assembled bra ke cylinder.
If the cylinder components are in a good condition, lubri cate them with brake fluid and
mount them in the reverse order of dismounting. Check the easy moving of the assembled pistons in the cylinder boring.
Mount the brake cylinder on the plate;
Mount the wheel brake drum .
Check the adjustment of t he hand bra ke.
Purge the braking system.
33 - 9
vnx.su

33
REAR BEARING ELEMENTS
BRAKE SHOES
DISMOUNTING
The re placement of brake shoes must
be performed in complete set, never mount
the brake shoes equipped with brake
linings of different brands and qualities. Dismount :
- t he brake drum ( see t he corre -
sponding paragraph); - the two m aintenance springs (R)
of the shoes with a brake cylinder rod (T). By means of the pliers FR05A the brake
cylinder pistons are immobilized. Remove t he return upper spri ng of the
shoes using the pliers FR03. Release the end of t he ha nd brake cable
off the hand brake lever.
Sw ing the adjustment lever (C) up t o t he
moment it c omes into contact with the re ar
wheel steering knuckle. Distance the shoes from the plate.
S
PECIAL TOOLS
DENOMINATION CODE
Plug extracting pliers RO441
Di smounting pliers for shoes return spring FR03
Pliers for maintaining brake cylinders pistons FR05A
TIGHTENING MOMENTS (daNm)
Wheel screw 7.5
Rear wheel steeri ng knuckle nut 16
33 - 10
vnx.su

33
REAR BEARING ELEMENTS
BEARING (25 x 52 x 37)CHECKING
Check by means of a comparing de vice attached on the drum , the axial cleara nce:
0 – 0.15 mm max after m ounting and tightening at the moment of 16 daNm.
DISMOUNTING
Di smount:
- the drum plug by means of the extra cting pliers RO441;
-r ear wheel steeri ng knuckle nut;
- the drum (see the corre sponding paragraph).
Di smount from the drum:
- the boring lock;
- the bearing by means of a tube F38mm.
If necessary, use the extractor CV28 A, in order to extract t he bearing inner ring, remained
on the steering knuckle. DENOMINATION
CODE
Plug extracting pliers RO441
Dr um extractor PF600
SPECIAL TOOLS
TIGHTENING MOMENTS (daNm)
Steering knuckle nut 16
Wheel attachment scre w 7.5
33 - 12
vnx.su

35
WHEELS AND TYRES
CARACTERISTICSRIMS
The wheels identification marking is represented in two ways:
- engraved marking for steel rims
- cast marking for aluminum rims
The marking enables acknowledgment of the main wheels dimensions criteria. This marking
may be:
complete,
Example: 5
1/2 B 13 4 CH 46 ; 5 1/2 J 13 4 H2 46
or simplified,
Example: 5
1/2 B 13 ; 5 1/2 J 13 H2
The wheel bolts (studs) are situated on a diameter of 100 mm.
Maximum axial runout : 1 mm measured on the rim edge ( in G ).
Maximum radial runout : 1 mm measured on the supporting side of the tires beads.
AB C D EF
Whe els Width The rim Æ Nominal Number of Tire Offset
type (in inches) edge profile rim (in inches) wholes under staffing profile (in mm) the tire bead
5
1/2B13 5 1/2B1 34C H46
4 CH48
5
1/2J13 5 1/2J1 34H 246
4H 2
35 - 1
vnx.su

WHEELS AND TYRES
35CARACTERISTICS
1 - 165 - Tire width in mm ( 1 )
2 - 70 - h / l height / width ratio;
4 - R - Radial structure
5 - 13 - Inner diameter in inches (Æ) ;
this is corresponding with the rim diameter
6 - 79 - Charging index
3 - T - Speed index max. 190 km/ h
Symbols speed
M ax speed
R 170
S 180
T 190
U 200
H 210
V 240
ZR more than 240
Stru cture types :
D iagonal No marking
Radial R
D iagonally belted B
TIRES
Identification marking examples: 165 / 70 R 13 79 T
165 / 70 R 13 79 T
1 2 4 5 6 3
35 - 2
vnx.su

35
WHEELS AND TYRES
CARACTERISTICSRIMS – TIRES
The wheels screws tightening moment : 7,5 daNm.
The inflating pressure must be checked at cold.
The temperature raising during driving, leads to a pressure increase from 0.2.
to 0.3 bars. In case temperature checking is done at warm, take i nto account this pressure increase and
never deflate it. A
ir filling pressure
(barr) at cold
Vehi cle Rim T i res Front Rear
R52315 5,5 B13 165/70R13 1,9 2,0
5,5 J13 165/70R13
35 - 3
vnx.su