engine electrical DAEWOO LACETTI 2004 Service Owners Manual

1F – 306IENGINE CONTROLS
DAEWOO V–121 BL4
DTC P1385 – Rough Road Sensor Circuit Fault (NON ABS)
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Turn the ignition ON, with engine OFF.
2. Install a scan tool to the Data Link Connector
(DLC).
3. Review and record the scan tool Failure Re-
cords data.
4. Operate the vehicle within Failure Records
conditions as noted.
5. Using the scan tool, monitor specific Diagnostic
Trouble Code (DTC) info for DTC P1385.
Does the scan tool indicate that DTC P1385 failed?–Go to Step 4Go to Step 3
31. Check for the following conditions and repair as
needed:
2. VR sensor seal missing or damaged.
3. VR sensor mounting flanges cracked, missing,
or incorrectly installed.
Is the repair complete?–Go to Step 14Go to
”Diagnostic
Aids”
41. Turn the ignition OFF.
2. Disconnect the VR sensor electrical connector.
3. Turn the ignition ON, with the engine OFF.
4. Observe the VR sensor value displayed on the
scan tool.
Is the VR sensor value near the specified value?0VGo to Step 5Go to Step 12
51. Jumper the 5 volt reference circuit, terminal C
and the VR sensor signal circuit, terminal 1 to-
gether at the VR sensor harness connector.
2. Observe the VR sensor value displayed on the
scan tool.
Is the VR sensor value near the specified value?4.95VGo to Step 14Go to Step 10
61. Turn the ignition OFF.
2. Disconnect the Engine Control Module (ECM)
and check the sensor ground circuit for high
resistance, an open between the ECM and the
VR sensor, or for a poor connection at the ter-
minal 53 of the ECM and repair as needed.
Is the repair complete?–Go to Step 14Go to Step 10
7Check the 5 volt reference circuit for high resistance,
an open between the ECM and the VR sensor, or a
poor connection at the terminal 84 of the ECM and
repair as needed.
Is the repair complete?–Go to Step 14Go to Step 8
81. Turn the ignition OFF.
2. Disconnect the ECM and check the VR sensor
signal circuit for high resistance, an open, a low
voltage, or a short to the sensor ground circuit
and repair as needed.
Is the repair complete?–Go to Step 14Go to Step 9

ENGINE CONTROLS 1F – 311
DAEWOO V–121 BL4
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive trip with a fail.
S The ECM will record operating conditions at the
time the diagnostic fail. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
Due to moisture associated with exhaust systems, the
EGR valve may freeze and stick in cold weather at times.
After the vehicle is brought into a warm shop for repairs,
the valve warms and the problem disappears.
By watching the Actual EGR and desired EGR positions
on a cold vehicle with a scan tool, the fault can be easily
verified. Check the Freeze Frame data to determine if the
DTC set when the vehicle was cold by viewing the Engine
Coolant Temperature (ECT).
DTC P1403 – Exhaust Gas Recirculation Valve Failure
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Turn the ignition switch to with the engine OFF.
2. Install the scan tool.
3. Command the exhaust gas recirculation (EGR)
valve to the specified values.
Does the Actual EGR Position follow the desired
EGR position?25%, 50%
75%, 100%Go to Step 19Go to Step 3
31. Turn the ignition switch to ON.
2. Disconnect the EGR valve electrical connector.
3. With a test light connected to B+, probe the
ground circuit to the EGR valve.
Does the test light illuminate?–Go to Step 4Go to Step 5
41. Connect the test light to ground.
2. Probe the EGR control circuit at terminal 3 to
the EGR valve.
3. Command the EGR valve to the specified val-
ues using a scan tool.
After the command is raised, does the test light glow
brighter, flash or maintain a steady glow?25%, 50%
75%, 100%Go to Step 6Go to Step 7
5Repair the open or poor connection in the EGR
ground circuit.
Is the repair complete?–Go to Step 19–
6With a test light still connected to ground, probe the
signal circuit at terminal 3.
Does the test light illuminate?–Go to Step 8Go to Step 9
7With a test light still connected to ground, again
probe the signal circuit without commanding the
EGR valve with the scan tool.
Does the test light illuminate?–Go to Step 10Go to Step 11
8Check the signal circuit for a short to voltage and re-
pair as necessary.
Is a repair necessary?–Go to Step 19Go to Step 12

1F – 312IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
9With a digital voltmeter (DVM) connected to ground,
probe the 5V reference circuit at terminal 1.
Is the voltage measured near the specified value?5VGo to Step 13Go to Step 14
10Check the control circuit for a short to battery voltage
and repair as necessary.
Is a repair necessary?–Go to Step 19Go to Step 12
11Connect the test light to B+ and again probe the con-
trol circuit at terminal 4.
Does the test light illuminate?–Go to Step 15Go to Step 16
12Replace the engine control module (ECM).
Is the replacement complete?–Go to Step 19–
13Check the EGR ground circuit for a poor connection
or proper terminal tension at the ECM and repair as
necessary.
Is a repair necessary?–Go to Step 19Go to Step 17
14Check the 5V reference circuit for a shortage to bat-
tery voltage and repair as necessary.
Is a repair necessary?–Go to Step 19Go to Step 12
15Check the control circuit for a shortage to ground
and repair as necessary.
Is a repair necessary?–Go to Step 19Go to Step 12
16Check the control circuit for an open or poor connec-
tion at the EGR valve electrical connector and repair
as necessary.
Is a repair necessary?–Go to Step 19Go to Step 18
17Replace the EGR valve.
Is the replacement complete?–Go to Step 19–
18Check the ECM electrical connector for a poor con-
nection and repair as necessary.
Is a repair necessary?–Go to Step 19Go to Step 12
191. Using the scan tool, clear the Diagnostic
Trouble Codes (DTCs).
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting the DTC as specifiec in the supporting
text.
Does the scan tool indicate that this diagnostic ran
and passed?–Go to Step 20Go to Step 2
20Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
Applicable DTC
tableSystem OK

1F – 314IENGINE CONTROLS
DAEWOO V–121 BL4
Diagnostic Aids
Due to moisture associated with exhaust systems, the
EGR valve may freeze and stick in cold weather at times.
After the vehicle is brought into a warm shop for repairs,
the valve warms and the problem disappears. By watchingthe Actual EGR and desired EGR positions on a cold ve-
hicle with a scan tool, the fault can be easily verified.
Check the Freeze Frame data to determine if the DTC set
when the vehicle was cold by viewing the Engine Coolant
Temperature (ECT).
DTC P1404 – Exhaust Gas Recirculation Closed
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Turn the ignition switch ON with the engine
OFF.
2. Install the scan tool.
3. Command the Exhaust Gas Recirculation
(EGR) valve to the specified values.
Does the Actual EGR Position follow the Desired
EGR Position?25%, 50%
75%, 100%Go to Step 13Go to Step 3
3Disconnect the EGR valve electrical connector.
Is the Actual EGR Position near the specified value?100%Go to Step 4Go to Step 5
4Check the signal circuit terminal 3 for a short to volt-
age and repair as necessary.
Is a repair necessary?–Go to Step 13Go to Step 6
5With a Digital Voltmeter (DVM) connected to ground,
probe the 5 volt reference circuit terminal 1 to the
EGR valve.
Does the DVM read near the specified valve?5VGo to Step 7Go to Step 8
61. Turn the ignition OFF.
2. Replace the Engine Control Module (ECM).
Is the repair complete?–Go to Step 13–
71. Connect a test light to ground.
2. Probe the EGR control circuit to the EGR
valve.
Does the test light illuminate?–Go to Step 9Go to Step 10
8Check the 5 volt reference circuit for a short to volt-
age and repair as necessary.
Is a repair necessary?–Go to Step 13Go to Step 6
9Check the control circuit for a short to voltage and re-
pair as necessary.
Is a repair necessary?–Go to Step 13Go to Step 6
10Check the EGR valve ground circuit for an open or
poor connection at the EGR valve electrical connec-
tor and repair as necessary.
Is a repair necessary?–Go to Step 13Go to Step 12
11Replace the EGR valve.
Is a action complete?–Go to Step 13–
12Check the EGR electrical connector for a poor con-
nection and repair as necessary.
Is a repair necessary?–Go to Step 13–

1F – 350IENGINE CONTROLS
DAEWOO V–121 BL4
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
2. This step will determine if DTC P0107 is the result
of a hard failure or an intermittent condition.
3. Jumpering harness terminals 2 to 1 (signal circuit to
5 volts) will determine if the sensor is malfunction-
ing or if there is a problem with the ECM or wiring.6. The scan tool may not display 5 volts. The Impor-
tant thing is that the ECM recognizes the voltage as
more than 4 volts, indicating that the ECM and the
signal circuit are OK. A test light that illuminates
indicates a short to ground in the signal circuit.
7. A short to ground in the 5 volt reference circuit
could also set additional DTCs.
11. The replacement ECM must be programmed. Refer
to the latest Techline procedure for the ECM repro-
gramming.
DTC P0107 Manifold Absolute Pressure Low Voltage
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data Link Connector
(DLC).
2. Start the engine.
3. Read the Manifold Absolute Pressure (MAP).
Does the scan tool display a MAP below the speci-
fied value?12 kPaGo to Step 3Go to Step 4
31. Turn the ignition switch OFF.
2. Disconnect the MAP sensor electrical connec-
tor.
3. Jumper the MAP signal circuit at terminal 2 to
the 5 volt reference circuit at terminal 1.
4. Turn the ignition switch ON.
Does the MAP read more than the specified value?96 kPaGo to Step 5Go to Step 6
41. Turn the ignition switch ON with the engine
OFF, review the Freeze Frame data, and note
the parameters.
2. Operate the vehicle within the freeze frame
conditions and Conditions For Setting the DTC
as noted.
Does the scan tool display MAP below the specified
value?12 kPaGo to Step 3Go to
”Diagnostic
Aids”
5Inspect the MAP sensor harness electrical connec-
tor terminals for the following conditions:
S Poor connections.
S Proper contact tension.
S Poor terminal to wire connection.
Is a problem found?–Go to Step 8Go to Step 9
61. Turn the ignition switch OFF.
2. Remove the jumper wire.
3. Probe the MAP sensor signal circuit terminal 2
with a test light to B+.
4. Turn the ignition switch ON.
Does the scan tool read over the specified value?90 kPaGo to Step 7Go to Step 12
7Check the MAP sensor 5 volt reference circuit at ter-
minal 1 for an open or short to ground.
Is a problem found?–Go to Step 10Go to Step 11

ENGINE CONTROLS 1F – 353
DAEWOO V–121 BL4
If DTC P0172 is also set, check 5 volt reference circuit for
short to voltage.
Test Description
Numbers below refer to the step numbers on the Diagnos-
tic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
2. This step will determine if DTC P0108 is the result
of a hard failure or an intermittent condition.
3. This step simulates conditions for a DTC P0107. If
the ECM recognizes the change, the ECM, the 5
volt reference and the sensor signal circuits are
OK.5. This step also looks for an open in the sensor
ground circuit. If the circuit was open, additional
DTCs will also be set. If no other DTCs are set and
the circuit is found to be open, then the open must
be between the MAP sensor and the electrical con-
nector ground splice.
6. When the sensor signal circuit is shorted to battery
voltage, the TP will be displayed above 0% at all
times and A/C High Side will be displayed high. The
vehicle will also remain in Open Loop.
8. The MAP sensor vacuum source should only sup-
ply vacuum to the MAP sensor. Check the vacuum
port for a restriction caused by casting flash.
9. Disconnect all sensors that use a 5 volt reference
one at a time while monitoring the short on the 5
volt reference circuit. Replace any sensor that may
have caused the short on the 5 volt reference cir-
cuit.
11. The replacement ECM must be programmed to the
latest Techline procedure for the ECM reprogram-
ming.
DTC P0108 – Manifold Absolute Pressure High Voltage
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data Link Connector
(DLC).
2. Start the engine.
3. Read the Manifold Absolute Pressure (MAP).
Does the scan tool display a MAP of the specified
value or over?85 kPaGo to Step 3Go to Step 4
31. Turn the ignition switch OFF.
2. Disconnect the MAP sensor electrical connec-
tor.
3. Turn the ignition switch ON.
Does the MAP read less than the specified value?28 kPaGo to Step 5Go to Step 6
41. Turn the ignition switch ON with the engine
OFF, review the Freeze Frame data, and note
the parameters.
2. Operate the vehicle within the freeze frame
conditions and Conditions For Setting the DTC
as noted.
Does the scan tool display MAP equal to or greter
than the specified value?85 kPaGo to Step 3Go to
”Diagnostic
Aids”
5Probe the MAP sensor signal ground circuit at termi-
nal 3 with a test light connected to battery +.
Does the test light illuminate?–Go to Step 7Go to Step 11
6Check the MAP sensor signal circuit at terminal M8
of ECM for a short to voltage and repair as needed.
Is a repair necessary?–Go to Step 14Go to Step 12

1F – 356IENGINE CONTROLS
DAEWOO V–121 BL4
DTC P0112 – Intake Air Temperature Low Voltage
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data Link Connector
(DLC).
2. Turn the ignition ON.
Is the Intake Air Temperature (IAT) value greater
than the specified value?128°C
(262 °F)Go to Step 4Go to Step 3
31. Turn the ignition switch ON with the engine
OFF, review Freeze Frame data, and note the
parameters.
2. Operate the vehicle within the Freeze Frame
conditions and Conditions for Setting The DTC
as noted.
Is the IAT sensor value greater than the specified
value?128°C
(262 °F)Go to Step 4Go to
”Diagnostic
Aids”
41. Turn the ignition switch OFF.
2. Disconnect the IAT sensor electrical connector.
3. Turn the ignition switch ON.
Is the IAT sensor value below the specified value?–30 °C
(–22 °F)Go to Step 5Go to Step 6
5Replace IAT sensor.
Is the repair complete?–Go to Step 10–
6With a test light connected to battery +, probe the
IAT sensor signal circuit, terminal 2 at the IAT sensor
connector.
Does the test light illuminate?–Go to Step 7Go to Step 9
71. Turn the ignition switch OFF.
2. Disconnect the Engine Control Module (ECM)
connector.
3. With a test light connected to B+, probe the
IAT sensor signal circuit, terminal 2 at the IAT
sensor electrical connector.
Does the test light illuminate?–Go to Step 8Go to Step 9
8Repair the short to ground circuit in the IAT sensor
signal circuit as needed.
Is the repair complete?–Go to Step 10–
91. Turn the ignition OFF.
2. Replace the ECM.
Is the action complete?–Go to Step 10–

ENGINE CONTROLS 1F – 359
DAEWOO V–121 BL4
DTC P0113 Intake Air Temperature High Voltage
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data Link Connector
(DLC).
2. Turn the ignition ON.
Is the Intake Air Temperature (IAT) value less than
the specified value?–30 °C
(–22 °F)Go to Step 4Go to Step 3
31. Turn the ignition switch ON with the engine
OFF, review Freeze Frame data, and note the
parameters.
2. Operate the vehicle within the Freeze Frame
conditions and Conditions for Setting The DTC
as noted.
Is the IAT sensor value less than the specified val-
ue?–30 °C
(–22 °F)Go to Step 4Go to
”Diagnostic
Aids”
41. Turn the ignition switch OFF.
2. Disconnect the IAT sensor electrical connector.
3. Turn the ignition switch ON.
4. Jumper the IAT sensor signal circuit terminal 2
and ground circuit terminal 1.
Is the IAT sensor value greater than the specified
value?130 °C
(266 °F)Go to Step 6Go to Step 5
5Jumper the IAT sensor signal circuit at terminal 1 to
ground.
Is the IAT sensor value greater than the specified
value?130 °C
(266 °F)Go to Step 7Go to Step 8
6Check for a poor connection at the IAT sensor con-
nector and repair or replace any malfunctioning ter-
minal as needed.
Is the repair necessary?–Go to Step 12Go to Step 10
7Check the IAT sensor ground circuit for an open and
repair as needed.
Is the repair complete?–Go to Step 12Go to Step 9
8Check the IAT sensor signal circuit for an open and
repair as needed.
Is the repair complete?–Go to Step 12Go to Step 9
9Check for a poor IAT sensor ground circuit at termi-
nal M64 or a poor IAT sensor signal circuit terminal
M7 connection at Engine Control Module (ECM) and
repair as needed.
Is the repair necessary?–Go to Step 12Go to Step 11
10Replace the IAT sensor.
Is the action complete?–Go to Step 12
111. Turn the ignition OFF.
2. Replace the ECM.
Is the action complete?–Go to Step 12–

1F – 386IENGINE CONTROLS
DAEWOO V–121 BL4
S Damaged harness
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
2. This step determines if DTC P0135 is the result of
a hard failure or an intermittent condition. With the
ignition ON, engine OFF, the HO2S1 voltage dis-played on the scan tool should change within sever-
al minutes toward 0 or 1 volt, indicating that the
heater is working properly.
3. Probing terminal 2 of the HO2S1 connector verifies
if voltage is available to the HO2S1 heater.
4. If voltage is available at the connector, than it be-
comes a good voltage source to check for a ground
at terminal 3.
5. Determines if voltage is not available at the HO2S1
due to an open in the HO2S1 fuse or open ignition
feed circuit. If the fuse is open, determine if it was
due to a short in the ignition feed circuit before re-
placing the fuse.
DTC P0135 – Front Heated Oxygen Sensor (HO2S1) Heater Circuit
Not Functioning
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
2Notice : If the engine has just been operating, allow
the engine to cool for about one–half hour before
proceeding.
1. Turn the ignition switch ON, with the engine
OFF.
2. Install a scan tool.
Does the Front Heated Oxygen Sensor (HO2S1)
voltage gradually change toward the specified volt-
age?0 v or 1 vGo to Step 13Go to Step 3
31. Disconnect the HO2S1 electrical connector.
2. With a test light connected to ground, probe
the ignition feed circuit, terminal 4 of the con-
nector.
Does the test light illuminate?–Go to Step 4Go to Step 5
4Connect a test light between the ignition feed and
ground circuits, terminal 4 and 3 of the connector.
Does the test light illuminate?–Go to Step 6Go to Step 7
5Inspect the fuse in the engine fuse block.
Is the fuse open?–Go to Step 8Go to Step 9
6Check the connections terminal 4 and 1 at the
HO2S1 connector and repair as necessary.
Is a repair necessary?–Go to Step 13Go to Step 10
7Check the connections terminal 3 at the HO2S1 con-
nector and repair as necessary.
Is a repair necessary?–Go to Step 13Go to Step 11
81. Check for a short to ground in the HO2S1 igni-
tion feed circuit and repair as necessary?
2. Replace open fuse.
Is the action complete?–Go to Step 13–

1F – 402IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
61. Disconnect the Manifold Absolute Pressure
(MAP) sensor electrical connector.
2. Operate the vehicle in Closed Loop while moni-
toring the Long Term Fuel Trim value.
Is the Long Term Fuel Trim value below the specified
value?25%Go to Step 15Go to Step 9
71. Repair the malfunction found in Step 5.
2. Recheck the Long Term Fuel Trim value while
operating the engine.
Is the Long Term Fuel Trim value below the specified
value?25%Go to Step 8Go to Step 9
8Lean condition is not present.
Does a driveability problem exist?–Go to
”Symptom
Diagnosis”Go to Step 16
91. Visually/physically inspect the following items
for vacuum leaks:
S Intake manifold.
S Throttle body.
S Injector O–rings.
2. Repair any leaks found as necessary.
Is the repair complete?–Go to Step 16Go to Step 10
10Allow the engine to idle.
Are the Idle Air Control (IAC) counts above the spe-
cified value?5Go to Step 11Go to Step 12
11Check the fuel for excessive water, alcohol, or other
contaminants and correct the contaminated fuel
condition if present.
Is the repair complete?–Go to Step 16Go to Step 13
12Check the IAC valve performance. Refer to ”DTC
P0506 Idle Speed RPM Lower Than Desired Idle
Speed” or ”DTC P0507 Idle Speed RPM Higher
Than Desired Idle Speed” in this section and repair
as necessary.
Is the repair complete?–Go to Step 16Go to Step 13
131. Connect a fuel pressure gauge to the fuel sys-
tem.
2. Turn the ignition OFF for at least 10 seconds.
3. Turn the ignition ON, with the engine OFF. The
fuel pump will run for approximately 2–3 sec-
onds. It may be necessary to cycle the ignition
switch ON more than once to obtain maximum
fuel pressure.
4. Note the fuel pressure with the fuel pump run-
ning. The pressure should be within the speci-
fied value. When the fuel pump stops, the pres-
sure may vary slightly then hold steady.
Is the fuel pressure steady and does the fuel pres-
sure hold?241–276 kPa
(35–40 psi)Go to Step 14Go to
”Fuel System
Diagnosis”