driver DAEWOO LACETTI 2004 Service Repair Manual

5A2 – 82IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0758
SHIFT SOLENOID 2 (SS2) ELECTRICAL
Conditions for Setting the DTC
S TCM detects that the ON signal of the Shift Sole-
noid 2 (SS2) monitor during 0.5 seconds when SS2
driver outputs the OFF signal.(When the SS2 circuit
is open or short to battery).
S TCM detects that the OFF signal of the Shift Sole-
noid 2 (SS2) monitor during 0.3 seconds when SS2
driver outputs the ON signal.(When the SS2 circuit
is short to ground).
S The above detection 2 times at shifting continuous-
ly.
Action Taken When the DTC Sets
S TCM will request the illumination of MIL and store
DTC when TCM detects a failure on the first ignition
cycle.
S No lockup control
S No engine torque reduction control
S No engagement pressure control
S No timing solenoid control for N–D
S No self–learning control
S After failure decision : emergency modeTCM Shifting Pattern (Range : D)
Normal
SS2 FAIL
GearSS1SS2GearSS1SS2
1 stONON2 ndONFAIL
2 ndONOFF2 ndONFAIL
3 rdOFFOFF3 rdOFFFAIL
4 thOFFON3 rdOFFFAIL
Conditions for Clearing the DTC
S The TCM turns off the MIL when no further failures
detected for three consecutive ignition cycles.
S The scan tool can clear the DTC from the TCM his-
tory.
S The TCM clears the DTC from the TCM history
memory after forty consecutive warm up cycles
without fault.
S TCM detects the ON signal of the SS2 monitor dur-
ing 160 ms when SS2 driver outputs the ON signal
and TCM detects the OFF signal of the SS2 moni-
tor during 160 ms when SS2 driver outputs the
OFF signal.

AISIN AUTOMATIC TRANSAXLE 5A2 – 85
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0785
TIMING SOLENOID (ST) ELECTRICAL
Conditions for Setting the DTC
S TCM detects that the ON signal of the Timing Sole-
noid (ST) monitor during 0.5 seconds when ST driv-
er outputs the OFF signal.(When the ST circuit is
open or short to battery).
S TCM detects that the OFF signal of the Timing So-
lenoid (ST) monitor during 0.1 seconds when ST
driver outputs the ON signal.(When the ST circuit is
short to ground).
S The above detection 3 times at shifting continuous-
ly.
Action Taken When the DTC Sets
S TCM will request the illumination of MIL and store
DTC when TCM detects a failure on the first ignition
cycle.
S After failure decision : emergency modeConditions for Clearing the DTC
S The TCM turns off the MIL when no further failures
detected for three consecutive ignition cycles.
S The scan tool can clear the DTC from the TCM his-
tory.
S The TCM clears the DTC from the TCM history
memory after forty consecutive warm up cycles
without fault.
S TCM detects the ON signal of the ST monitor dur-
ing 100 ms when ST driver outputs the ON signal
and TCM detects the OFF signal of the ST monitor
during 160 ms when ST driver outputs the OFF sig-
nal.
Cause of Failure
S Wiring harness or connector between Timing Sole-
noid (ST) and TCM
S ST
S TCM

5A2 – 102IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
3. Remove the E–ring.
4. Disconnect the shift control cable from the TR
switch lever.
5. Remove the retaining nut and then remove the
washer and the control lever.
6. Using a driver, unstake the lock washer and re-
move the nut.
Installation Procedure
1. Install the Transmission Range (TR) switch onto the
manual valve lever shaft and temporarily install the
2 adjusting bolts.
2. Install the new lock washer and nuts.
Tighten
Tighten the nuts to 12 NSm (106 Ib–in).
3. Temporarily install the control lever.
4. Turn the lever counterclockwise until it stops, then
turn it clockwise 2 notches.
5. Remove the control lever.

AISIN AUTOMATIC TRANSAXLE 5A2 – 103
DAEWOO V–121 BL4
6. Aligh the groove with the neutral basic line, then
install the 2 bolts.
Tighten
Tighten the 2 bolts to 5.4 NSm (48 Ib–in).
7. Using a screw driver, stake the nut with the lock
washer.
8. Install the control lever, washer and nut.
Tighten
Tighten the nut to 12 NSm (106 Ib–in).
9. Connect the control cable to TR switch.
10. Connect the TR switch electrical connector.
11. Adjust the control cable. Refer to ”Control Cable
Adjustment” in this section.
12. Install the control cable adjusting nut.
Tighten
Tighten the control cable adjusting nut to 8 NSm (71
Ib–in).
13. Connect the negative battery cable.

AISIN AUTOMATIC TRANSAXLE 5A2 – 117
DAEWOO V–121 BL4
UNIT REPAIR
MAJOR COMPONENT DISASSEMBLY
Tools Required
DW240–020 Brake/Clutch Spring Compressor
DW240–050 Overdrive Brake Adapter
DW240–060–01 Brake Spring Compressor Bolt/Nut
DW240–070 1st & Reverse Brake Adapter
DW240–080 2nd Brake Adapter
DW240–090 Planetary Ring Gear Remover
DW240–150 Transaxle Case Side Bearing Outer Race
Adapter
DW240–170 Adapter Handle
DW260–021–02 Automatic Transaxle Overhaul Fixture
(81–40 LE)
DW260–041 Planetary Ring Gear Nut Removal/Installa-
tion Socket
Disassembly Procedure
1. Remove the transaxle assembly from the vehicle.
Refer to”Transaxle Assembly” in this section.
2. Install the transaxle assembly to the transaxle sup-
port stand using Automatic Transaxle Overhaul Fix-
ture DW260–021–02 (81–40 LE).
3. Remove the nut, washer and control lever.
4. Using a screwdriver, unstake the lock washer.
5. Remove the two bolts and nut and pull out the
transmission range (TR) switch.
6. Remove the two unions the transaxle case.
7. Remove the two O–rings from the unions.

5A2 – 132IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
73. Using a screwdriver, remove the oil seal.
74. Using brake spring compressor bolt/nut
DW240–060–01, 1st & reverse brake adapter
DW240–070 and planetary ring gear remover
DW240–090, remove the planetary ring gear.
75. Install the 3 bolts to the counter drive gear.
S Bolt (M6) : L= 40–80mm, Pich = 1.0mm
76. Rotate 3 bolts in order and remove the counter
drive gear and planetary ring gear.
WARNING : USE CAUTION WHEN REMOVING SNAP
RINGS OR PERSONAL INJURY MAY RESULT.
77. Using brake spring compressor bolt/nut
DW240–060–01 and 1st & reverse brake adapter
DW240–070, remove the snap ring of 1st & reverse
brake.

5A2 – 134IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
82. Using a suitable puller, remove the counter driven
gear outer tapered roller bearing race and shim
from the transaxle case.
83. Using a driver, remove the oil seal from the trans-
axle case.
Notice : Be careful not to damage the transaxle case
when removing the oil seal using a driver.
84. Using transaxle case side bearing outer race adapt-
er DW240–150 and adapter handle DW240–170,
remove the transaxle case side bearing outer race
and shim.
85. Remove the 3 bolts and oil reservoir lock plate from
the transaxle housing.
86. Remove the bolt and No.1 transaxle apply pipe
clamp from the transaxle housing.
87. Remove the transaxle lube apply pipe and differen-
tial gear lube apply pipe from the transaxle housing.

AISIN AUTOMATIC TRANSAXLE 5A2 – 135
DAEWOO V–121 BL4
88. Using a suitable puller, remove the counter driven
gear outer tapered roller bearing race from the
transaxle housing.
89. Using a driver, remove the oil seal from the trans-
axle housing.
Notice : Be careful not to damage the transaxle housing
when removing the oil seal using a driver.
90. Using a suitable puller, remove the side bearing
outer race from the transaxle housing.
WARNING : USE CAUTION WHEN REMOVING SNAP
RINGS OR PERSONAL INJURY MAY RESULT.
Notice : Stop the press when the O/D brake piston is low-
ered 1–2 mm (0.039–0.078 in.) from the snap ring groove,
preventing the O/D brake piston from being deformed.
91. Using brake/clutch spring compressor DW240–020,
overdrive brake adapter DW240–050 and a driver,
remove the snap ring.
92. Remove the O/D brake return spring.

5A2 – 138IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
5. Coat 2 new O–rings with ATF, install them to the
O/D brake piston.
6. Coat the O/D brake piston with ATF, install it to the
transaxle rear cover.
Notice : Be careful not to damage the O–rings of the O/D
brake piston.
7. Using brake/clutch spring compressor DW240–020,
overdrive brake adapter DW240–050 and a driver,
install the O/D brake return spring and snap ring to
the transaxle rear cover.
Notice : Stop the press when the O/D brake piston is low-
ered 1–2 mm (0.039
0.078 in.) from the snap ring groove,
preventing the O/D brake piston from being deformed.
8. Using transaxle housing side bearing outer race
adapter DW240–140 and adapter handle
DW240–170, install a new side bearing outer race
into the transaxle housing.

5A2 – 152IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
68. Using brake spring compressor bolt / nut
DW240–060–01 and 2nd brake adapter
DW240–080, compress the 2nd brake piston return
spring.
69. Using a screwdriver, install the snap ring.
Notice : Make sure that the snap ring is installed in the
groove of the transaxle case correctly.
70. Coat the thrust bearing race with petroleum jelly
and install it onto the front planetary sun gear.
S Race:
Inner diameter: 19.3 mm (0.760 in.)
Outer diameter : 29.0 mm (1.142 in.)
71. Install the front planetary sun gear to the transaxle
case.
72. Install the thrust washer and one–way clutch as-
sembly to the rear planetary sun gear.