battery DAEWOO LACETTI 2004 Service Repair Manual

BODY WIRING SYSTEM 9A – 13
DAEWOO V–121 BL4
FUSE CHART
Engine Room Fuse Block
FuseRating/SourceCircuit
EF130AB+Battery Main (F13~F16, F21~F24)
EF260AB+EBCM, Oil Feeding Connector
EF330AB+Blower Relay
EF430AB+Ignition Switch–2
EF530AB+Ignition Switch–1
EF620AB+Cooling Fan Low Relay
EF730AB+Defog Relay
EF830AB+Cooling Fan HI Relay
EF920AIGN 2Power Window Switch
EF1015AIGN 1Fuel Connector, ECM (MR–140), LEGR, EI Sys-
tem
EF1110AB+ECM, Main Relay (Sirius D4)
EF1225AB+Head Lamp Relay, ILLUM. Relay
EF1315AB+Brake Switch
EF1420AIGN 2Power Window Switch
EF1515ALightHead Lamp HI
EF1615AB+Horn Relay, Siren, Hood Contact Switch
EF1710AB+A/C Comp. Relay
EF1815AIGN 1Fuel Pump
EF1915AB+Cluster, Key Remind S/W, Folding Mirror Unit,
MAP Lamp, Room Lamp, Trunk Open Lamp,
Trunk Open S/W
EF2010ALightHead Lamp Low
EF2115AIGN 1/B+EVAP Canister Purge Solenoid, HO2S, Cooling
Fan Relay
EF2215AIGN 1/B+Injector, EGR, EEGR
EF2310AIlluminationLicense Plate Lamp, Chime Bell, Tail Lamp,
Head Lamp
EF2415AB+Fog LampRelay
EF2510AIGN 2Electric OSRV Mirror
EF2615AB+Central Door Lock Unit
EF2710ALightHead Lamp Low
EF2810AIlluminationILLUM. Circuit, Head Lamp, Tail Lamp
EF2910ASpareNot Used
EF3015ASpareNot Used
EF3125ASpareNot Used

SECTION : 9B
LIGHTING SYSTEMS
CAUTION : Disconnect the negative battery cable before removing or installing any electrical unit or when a tool
or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable will help
prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise noted.
TABLE OF CONTENTS
SPECIFICATIONS9B–2 . . . . . . . . . . . . . . . . . . . . . . . . . .
Bulb Usage Chart 9B–2. . . . . . . . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications 9B–2. . . . . . . . . . .
SCHEMATIC AND ROUTING DIAGRAMS9B–3 . . . . .
Backup Lamps Circuit 9B–3. . . . . . . . . . . . . . . . . . . . . .
Instruments Circuit (W/O Dimmer Control :
General Only) 9B–4. . . . . . . . . . . . . . . . . . . . . . . . . . .
Instruments Circuit (W/ Dimmer Control) 9B–5. . . . . .
Front And Rear Fog Lamps Circuit 9B–6. . . . . . . . . . .
Headlamps–On Reminder Chime Circuit 9B–7. . . . . .
Headlamps and Headlamp Leveling Circuit 9B–8. . . .
Daytime Running Lamps Circuit 9B–9. . . . . . . . . . . . .
Parking, Tail and License Lamps Circuit 9B–10. . . . . .
Stoplamps Circuit 9B–11. . . . . . . . . . . . . . . . . . . . . . . . .
Turn and Hazard Lamps Circuit 9B–12. . . . . . . . . . . . .
Interior Courtesy and Luggage Compartment Lamp
Circuit 9B–13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS9B–14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlamps–On Reminder Chime 9B–14. . . . . . . . . . .
Headlamps 9B–16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlamp Leveling 9B–20. . . . . . . . . . . . . . . . . . . . . . .
Daytime Running Lamps 9B–22. . . . . . . . . . . . . . . . . . .
Parking Lamps and Taillamps 9B–23. . . . . . . . . . . . . .
Interior Courtesy and Luggage Compartment
Lamps 9B–31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fog Lamps 9B–34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE AND REPAIR9B–36 . . . . . . . . . . . . . .
ON–VEHICLE SERVICE 9B–36. . . . . . . . . . . . . . . . . . . . Headlamps/Front Turn Signal Lamps 9B–36. . . . . . . .
Daytime Running Lamp Module 9B–37. . . . . . . . . . . . .
Parking Lamps 9B–37. . . . . . . . . . . . . . . . . . . . . . . . . . .
Side Turn Signal Lamps 9B–38. . . . . . . . . . . . . . . . . . .
Front Fog Lamps 9B–38. . . . . . . . . . . . . . . . . . . . . . . . .
Notchback Rear Combination Lamps 9B–39. . . . . . . .
Hatchback Rear Combination Lamps 9B–40. . . . . . . .
Hatchback Extension Lamps 9B–40. . . . . . . . . . . . . . .
Notchback Center High–Mounted Stoplamp 9B–41. .
Hatchback Center High–Mounted Stoplamp 9B–41. .
License Plate Lamps 9B–42. . . . . . . . . . . . . . . . . . . . . .
Door Jamb Switch 9B–42. . . . . . . . . . . . . . . . . . . . . . . .
Center Room Lamp 9B–43. . . . . . . . . . . . . . . . . . . . . . .
Map Lamp 9B–43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Luggage Compartment Lamp 9B–44. . . . . . . . . . . . . . .
Ashtray and Cigar Lighter Lamp 9B–44. . . . . . . . . . . .
GENERAL DESCRIPTION AND SYSTEM
OPERATION9B–46 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlamps–On Reminder Chime 9B–46. . . . . . . . . . .
Headlamps 9B–46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Daytime Running Lamps 9B–46. . . . . . . . . . . . . . . . . . .
Parking and Turn Signal Lamps 9B–46. . . . . . . . . . . . .
Fog Lamps 9B–46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Combination Lamps 9B–46. . . . . . . . . . . . . . . . . .
License Plate Lamp 9B–46. . . . . . . . . . . . . . . . . . . . . . .
Interior Courtesy Lamp 9B–46. . . . . . . . . . . . . . . . . . . .
Luggage Compartment Lamp 9B–46. . . . . . . . . . . . . . .
Backup Lamps 9B–47. . . . . . . . . . . . . . . . . . . . . . . . . . .

9B – 18ILIGHTING SYSTEMS
DAEWOO V–121 BL4
High–Beam and Low–Beam Headlamps Are Inoperative On Both
Left and Right Sides
StepActionValue(s)YesNo
1Check fuses F6, Ef2, Ef20, Ef27 and Ef15.
Is any fuse blown?–Go to Step 2Go to Step 3
21. Check for a short circuit and repair if neces-
sary.
2. Replace the fuse.
Is the repair complete?–System OK–
31. Turn the low–beam headlamps ON.
2. Check the voltage at fuses Ef20, Ef27 and
Ef15.
Does the voltage at the headlamps equal the value
specified?11–14 vGo to Step 4Go to Step 9
41. Turn the low–beam headlamps ON.
2. Check the voltage at the headlamp connector
terminal 5.
3. Turn the high–beam headlamps ON.
4. Check the voltage at headlamp connector ter-
minal 4.
Does the battery voltage available at the headlamps
equal the value specified?11–14 vGo to Step 6Go to Step 5
5Repair the open circuit between fuses Ef20, Ef27
and Ef15 and the headlamps.
Is the repair complete?–System OK–
6Use an ohmmeter to check between ground and
each headlamp connector terminal 6.
Is the resistance equal to the specified value?0 WGo to Step 8Go to Step 7
7Repair the ground circuit.
Is the repair complete?–System OK–
81. Replace the faulty headlamps.
2. Check the charging system to make sure that
charging voltage is not excessively high. Re-
pair if necessary.
Is the repair complete?–System OK–
9Temporarily substitute the illumination relay in place
of the headlamp relay.
Do the headlamps operate with the substituted
relay?–Go to Step 10Go to Step 11
10Install the illumination relay in its original position,
and install a new headlamp relay.
Is the repair complete?–System OK–
111. With the headlamp relay removed, turn the
headlamp switch to the low–beam position.
2. Use an ohmmeter to check the continuity be-
tween the connector for relay terminal 85 and
ground.
Does the ohmmeter indicate the specified value?
0 WGo to Step 17Go to Step 12

9B – 26ILIGHTING SYSTEMS
DAEWOO V–121 BL4
Backup Lamps Inoperative
StepActionValue(s)YesNo
11. Block the wheels.
2. Apply the parking brake to prevent the vehicle
from moving.
3. Turn the ignition on.
4. Put the transaxle in reverse (R).
5. Remove one of the backup lamps from its
socket.
6. Test the lamp socket positive terminal with a
voltmeter.
Does the battery voltage available at the backup
lamp socket positive terminal equal the specified
value?11–14 vGo to Step 3Go to Step 2
2Repair the open circuit between fuse F20 and the
backup lamps.
Is the repair complete?–System OK–
3Connect an ohmmeter between ground and the neg-
ative terminal at the bulb socket.
Is the resistance equal to the specified value?0 WGo to Step 4Go to Step 5
4Replace the faulty backup lamps.
Is the repair complete?–System OK–
51. Reinstall the backup lamps.
2. Disconnect the electrical connector at the re-
verse switch. (On automatic transaxle (A/T)
vehicles, disconnect the neutral safety/backup
switch.)
3. Turn the ignition on.
4. Put the transaxle in R.
5. Use a voltmeter to check for the reverse switch
terminal 1. (On A/T vehicles, test terminal 7 of
the neutral safety/backup switch).
Does the battery voltage available at terminal 1 (or
terminal 7, if equipped with A/T) equal the specified
value?11–14 vGo to Step 7Go to Step 6
6Repair the open circuit between the backup lamps
and the, reverse switch (or the neutral safety/backup
switch if equipped with A/T).
Is the repair complete?–System OK–
71. Put the transaxle in R.
2. Use an ohmmeter to check the continuity be-
tween reverse switch terminal 1 and terminal 2
(terminals 7 and 8 on the neutral safety/backup
switch, if equipped with A/T).
Does the continuity between terminals 1 and 2 (ter-
minals 7 and 8, if equipped with A/T) equal the speci-
fied value?0 WGo to Step 9Go to Step 8

9B – 28ILIGHTING SYSTEMS
DAEWOO V–121 BL4
Turn Signal Lamps and Hazard Lamps Do Not Work
StepActionValue(s)YesNo
1Check fuses F3 and F14.
Is either fuse blown?–Go to Step 2Go to Step 3
21. Check for a short circuit and repair it, if neces-
sary.
2. Replace the fuse.
Is the repair complete?–System OK–
31. Turn the ignition ON.
2. Check the voltage at fuses F3 and F14.
Does the battery voltage available at both fuses F3
and F14 equal the specified value?11–14 vGo to Step 4Go to Step 7
41. Turn the hazard switch on.
2. Remove each of the inoperative lamps from its
socket.
3. Test each lamp socket positive terminal with a
voltmeter.
Does the battery voltage pulsing at the turn signal
hazard lamp socket positive terminal equal the spe-
cified value?11–14 vGo to Step 5Go to Step 9
5At each bulb socket, use an ohmmeter to check the
ground circuit.
Is the resistance equal to the specified value?
0 WGo to Step 6Go to Step 8
6Replace any faulty turn signal/hazard bulbs.
Is the repair complete?–System OK–
7Repair the power supply circuit to fuses.
Is the repair complete?–System OK–
8Repair the open ground wires.
Is the repair complete?–System OK–
91. Turn on the hazard lamp switch.
2. Test the blinker unit connector terminal 49a
with a voltmeter.
Does the battery voltage pulsing at the blinker unit
terminal 49a equal the specified value?11–14 vGo to Step 15Go to Step 10
101. Turn on the hazard lamp switch.
2. Test the blinker unit connector terminal 49 with
a voltmeter.
Does the battery voltage available at the blinker unit
terminal 49 equal the specified value?11–14 vGo to Step 11Go to Step 14
111. Disconnect the blinker unit from the connector.
2. Use an ohmmeter to check between ground
and the connector for terminal 31 of the blinker
unit.
Is the resistance equal to the specified value?
0 WGo to Step 13Go to Step 12
12Repair the blinker unit ground connection.
Is the repair complete?–System OK–
13Replace the faulty blinker unit.
Is the repair complete?–System OK–

LIGHTING SYSTEMS 9B – 29
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
141. Disconnect the hazard lamp switch connector.
2. Check for voltage at terminal 8.
3. Turn the ignition ON.
4. Check for voltage at terminal 10.
Does the battery voltage available at both terminals
equal the specified value?11–14 vGo to Step 15Go to Step 20
151. Remove the hazard lamp switch.
2. Turn the hazard lamp switch off.
3. Check for continuity between terminals 7 and
10.
4. Turn the hazard lamp switch on.
5. Check for continuity between terminals 7 and
8.
Do both tests show the specified value?0 WGo to Step 18Go to Step 17
161. Remove the hazard lamp switch.
2. Turn the hazard lamp switch on.
3. Use an ohmmeter to check for continuity be-
tween terminals 5, 6, and 9.
Does the continuity between terminals 5, 6, and 9
equal the specified value?0 WGo to Step 19Go to Step 17
17Replace the faulty hazard lamp switch.
Is the repair complete?–System OK–
18Repair the open circuit between the hazard lamp
switch terminal 7 and the blinker unit terminal 49.
Is the repair complete?–System OK–
19Repair the open circuit between the hazard lamp
switch and the fuses F3 or F14.
Is the repair complete?–System OK–

9B – 30ILIGHTING SYSTEMS
DAEWOO V–121 BL4
Hazard Lamps Do Not Operate, Turn Signals Are OK
StepActionValue(s)YesNo
1Check fuse F14.
Is fuse F14 blown?–Go to Step 2Go to Step 3
21. Check for a short circuit and repair it, if neces-
sary.
2. Replace the fuse.
Is the repair complete?–System OK–
3Use a voltmeter to check for power to fuse F14.
Does the battery voltage available at fuse F14 equal
the value specified?11–14 vGo to Step 5Go to Step 4
4Repair the power supply circuit to fuse F14.
Is the repair complete?–System OK–
51. Disconnect the hazard switch connector.
2. Use a voltmeter to check power to the hazard
switch terminal 8.
Does the battery voltage available at connector ter-
minal 8 equal the value specified?11–14 vGo to Step 6Go to Step 9
61. Remove the hazard switch and disconnect it
for testing.
2. Turn the hazard switch on.
3. Test with an ohmmeter between terminals 7
and 8.
Is the resistance equal to the specified value?0 WGo to Step 7Go to Step 10
71. With the hazard switch still removed and dis-
connected for testing, turn the hazard switch
on.
2. Use an ohmmeter to check between terminals
5, 6, and 9.
Is the resistance equal to the specified value?0 WGo to Step 8Go to Step 10
8Repair the open circuit between the hazard lamp
switch connector and splice S202.
Is the repair complete?–System OK–
9Repair the open circuit between the hazard switch
connector terminal 8 and fuse F14.
Is the repair complete?–System OK–
10Replace the faulty hazard switch.
Is the repair complete?–System OK–

LIGHTING SYSTEMS 9B – 31
DAEWOO V–121 BL4
INTERIOR COURTESY AND LUGGAGE COMPARTMENT
LAMPS
Interior Courtesy Lamp Inoperative
CAUTION : Always make sure there is an electrical
load (lamp bulb, etc.) in any circuit between battery
terminals. Do not make a short circuit between bat-
tery terminals with a jumper wire. Hazardous spark-
ing would result and could cause injury.
Test Description
The number(s) below refer to step(s) on the diagnostictable.
1. Bulb test. Clip one end of a jumper wire to the neg-
ative battery terminal. Clip the other end of the
jumper wire onto one end of the bulb. Take the free
end of the bulb (the end without the jumper at-
tached) and touch it to the positive battery terminal.
Step
ActionValue(s)YesNo
11. Remove the interior courtesy lamp bulb and
inspect the filament.
2. If the filament is not broken, test the bulb using
the vehicle’s battery and a jumper wire.
Does the bulb pass the visual and physical checks?–Go to Step 3Go to Step 2
2Replace the bulb.
Is the repair complete?–System OK–
31. Reinstall the interior courtesy lamp bulb.
2. Check fuse Ef19.
Is fuse Ef19 blown?–Go to Step 4Go to Step 5
41. Check for a short circuit and repair it, if neces-
sary.
2. Replace the fuse.
Is the repair complete?–System OK–
5Check fuse Ef19.
Does the voltage at fuse Ef19 equal the specified
value?11–14 vGo to Step 7Go to Step 6
6Repair the open power supply circuit for fuse Ef19.
Is the repair complete?–System OK–
71. Disconnect the interior courtesy lamp electrical
connector.
2. Check the voltage at connector terminal 1.
Does the voltage at connector terminal 1 equal the
value specified?11–14 vGo to Step 8Go to Step 9
8Repair the open circuit between fuse Ef19 and the
interior courtesy lamp terminal 1.
Is the repair complete?–System OK–
91. With the interior courtesy lamp disconnected,
turn it to the on position.
2. Use an ohmmeter to check the resistance be-
tween ground and terminal 2 of the interior
courtesy lamp connector (harness side).
Is the resistance equal to the specified value?0WGo to Step 10Go to Step 11
10Replace the interior courtesy lamp switch assembly.
Is the repair complete?–System OK–
11Repair the ground circuit for the interior courtesy
lamp.
Is the repair complete?–System OK–

9B – 32ILIGHTING SYSTEMS
DAEWOO V–121 BL4
Luggage Compartment Lamp Inoperative
CAUTION : Always make sure there is an electrical
load (lamp bulb, etc.) in any circuit between battery
terminals. Do not make a short circuit between bat-
tery terminals with a jumper wire. Hazardous spark-
ing would result and could cause injury.
Test Description
The number(s) below refer to step(s) on the diagnostictable.
1. Bulb test. Clip one end of a jumper wire to the neg-
ative battery terminal. Clip the other end of the
jumper wire onto one end of the bulb. Take the free
end of the bulb (the end without the jumper at-
tached) and touch it to the positive battery terminal.
Step
ActionValue(s)YesNo
11. Remove the luggage compartment lamp bulb
and inspect the filament.
2. If the filament is not broken, test the bulb using
the vehicle’s battery and a jumper wire.
Does the bulb pass the visual and physical check?–Go to Step 3Go to Step 2
2Replace the bulb.
Is the repair complete?–System OK–
31. Reinstall the luggage compartment lamp bulb.
2. Check fuse Ef19.
Is fuse Ef19 blown?–Go to Step 4Go to Step 5
41. Check for a short circuit and repair it, if neces-
sary.
2. Replace the fuse.
Is the repair complete?–System OK–
5Check fuse Ef19.
Does the voltage at fuse Ef19 equal the specified
value?11–14 vGo to Step 7Go to Step 6
6Repair the open power supply circuit for fuse Ef19.
Is the repair complete?–System OK–
71. Disconnect the luggage compartment lamp
electrical connector.
2. Check the voltage at the orange wire.
Does the voltage at the ORN wire equal the specified
value?11–14 vGo to Step 8Go to Step 9
8Repair the open circuit between fuse Ef19 and the
luggage compartment lamp.
Is the repair complete?–System OK–
91. Reconnect the luggage compartment lamp.
2. Remove the luggage compartment lamp
switch.
3. With a voltmeter (or test lamp), test the PNK/
BLK wire at the luggage compartment lamp
switch.
Does the voltage at the luggage compartment lamp
switch equal the specified value?11–14 vGo to Step 11Go toStep 10
10Repair the open circuit between the luggage
compartment lamp and the luggage compartment
lamp switch.
Is the repair complete?–System OK–

9B – 34ILIGHTING SYSTEMS
DAEWOO V–121 BL4
FOG LAMPS
Diagnostic Aids
The front fog lamps will not operate unless the illumination lamps or daytime running lamps are on. If the illumination lamps
or daytime running lamps are not operating, repair that problem before attempting to diagnose the fog lamps.
Front Fog Lamps Inoperative
StepActionValue(s)YesNo
1Check fuse Ef24.
Is fuse Ef24 blown?–Go to Step 2Go to Step 3
21. Check for a short circuit and repair it, if neces-
sary.
2. Replace the fuse.
Is the repair complete?–System OK–
3Use a voltmeter to check fuse Ef24.
Does the battery voltage available at fuse Ef24 equal
the specified value?11–14 vGo to Step 5Go to Step 4
4Repair the open circuit from the battery to fuse Ef24.
Is the repair complete?–System OK–
5Remove the fog lamp relay and temporarily substi-
tute a known good relay, such as the headlamp relay.
(Do not substitute the illumination lamp relay.)
Do the fog lamps work with the substituted relay?–Go to Step 6Go to Step 7
61. Return the substituted relay to its original posi-
tion.
2. Replace the inoperative fog lamp relay.
Is the repair complete?–System OK–
71. Return the substituted relay to its original posi-
tion, but do not reinstall the fog lamp relay.
2. Turn on the exterior lamps and the front fog
lamps.
3. Using a voltmeter, check the fog lamp relay
socket at the connector for fog lamp relay ter-
minal 30.
Does the voltage available at the fog lamp relay
socket equal the specified value?11–14 vGo to Step 9Go to Step 8
8Repair the open circuit between fuse Ef24 and the
fog lamp relay.
Is the repair complete?–System OK–
9At the fog lamp relay socket, use an ohmmeter to
verify that the connector for relay terminal 85 is con-
nected to ground.
Does the resistance equal the specified value?0 WGo to Step 11Go to Step 10
10Repair the ground circuit for the fog lamp relay.
Is the repair complete?–System OK–
111. Reinstall the fog lamp relay.
2. Turn ON the exterior lamps and the front fog
lamps.
3. Test for voltage at terminal 2 of the fog lamp
connector.
Does the battery voltage available at terminal 2 of
the fog lamp connector equal the specified value?11–14 vGo to Step 13Go to Step 12