battery DAEWOO LACETTI 2004 Service Repair Manual

SECTION : 8B
SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
CAUTION : Disconnect the negative battery cable before removing or installing any electrical unit or when a tool
or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable will help
prevent personal injury and damage to the vehicle. The ignition mujst be also be in LOCK unless otherwise noted
TABLE OF CONTENTS
SPECIFICATIONS8B–3 . . . . . . . . . . . . . . . . . . . . . . . . . .
General Specifications 8B–3. . . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications 8B–3. . . . . . . . . . .
SPECIAL TOOLS8B–3 . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS TABLE 8B–3. . . . . . . . . . . . . . . . . . .
SCHEMATIC AND ROUTING DIAGRAMS8B–4 . . . . .
Supplemental Inflatable Restraints(SIR)
Electronical Schematic 8B–4. . . . . . . . . . . . . . . . . . . .
SIR Component Locator 8B–5. . . . . . . . . . . . . . . . . . . .
DIAGNOSIS8B–6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) 8B–6. . . . . . . . . . . . . .
Scan Tool Diagnostics 8B–7. . . . . . . . . . . . . . . . . . . . . .
SIR Diagnostic System Check 8B–8. . . . . . . . . . . . . . .
Sensing and Diagnostic Module (SDM) Integrity
check 8B–10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC 1 Driver Airbag Deployment Loop Resistance
Is High 8B–12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC 2 Driver Airbag Deployment Loop Resistance
Is Low 8B–14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC 3 Driver Airbag Deployment Loop Is Shorted
To Ground 8B–16. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC 4 Driver Airbag Deployment Loop Is Shorted
To Power 8B–18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC 5 Passenger Airbag Deployment Loop
Resistance Is High 8B–20. . . . . . . . . . . . . . . . . . . . . .
DTC 6 Passenger Airbag Deployment Loop
Resistance Is Low 8B–22. . . . . . . . . . . . . . . . . . . . . .
DTC 7 Passenger Airbag Deployment Loop Is
Shorted To Ground 8B–24. . . . . . . . . . . . . . . . . . . . . .
DTC 8 Passenger Airbag Deployment Loop Is
Shorted To Power 8B–26. . . . . . . . . . . . . . . . . . . . . . .
DTC 9 Driver Belt Pretensioner Deployment
Loop Resistance Is High 8B–28. . . . . . . . . . . . . . . . .
DTC 10 Driver Belt Pretensioner Deployment
Loop Resistance Is Low 8B–30. . . . . . . . . . . . . . . . . .
DTC 11 Driver Belt Pretensioner Deployment
Loop Is Shorted To Ground 8B–32. . . . . . . . . . . . . . . DTC 12 Driver Belt Pretensioner Deployment
Loop Is Shorted To Power 8B–34. . . . . . . . . . . . . . . .
DTC 13 Passenger Belt Pretensioner Deployment
Loop Resistance Is High 8B–36. . . . . . . . . . . . . . . . .
DTC 14 Passenger Belt Pretensioner Deployment
Loop Resistance Is Low 8B–38. . . . . . . . . . . . . . . . . .
DTC 15 Passenger Belt Pretensioner Deployment
Loop Is Shorted To Ground 8B–40. . . . . . . . . . . . . . .
DTC 16 Passenger Belt Pretensioner Deployment
Loop Is Shorted To Power 8B–42. . . . . . . . . . . . . . . .
DTC 23 Battery Voltage high 8B–44. . . . . . . . . . . . . . .
DTC 24 Battery Voltage Low 8B–46. . . . . . . . . . . . . . .
DTC 25 Airbag Warning Lamp Failure 8B–48. . . . . . .
DTC 31 Internal Sensing Diagnostic Module
(SDM) Failure 8B–50. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC 32 Airbag Inflation Record By Frontal
Collision 8B–51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC 33 Driver Side Airbag Inflation Record By
Side Impact 8B–52. . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC 34 Passenger Side Airbag Inflation Record
By Side Impact 8B–53. . . . . . . . . . . . . . . . . . . . . . . . .
DTC 35 Belt Pretensioner Explosion Record 8B–54. .
DTC 38 Side Airbag And Belt Pretensioner
Explosion Count Over 5 8B–55. . . . . . . . . . . . . . . . . .
DTC 52 Driver Side Airbag Deployment Loop
Resistance Is High 8B–56. . . . . . . . . . . . . . . . . . . . . .
DTC 53 Driver Side Airbag Deployment Loop
Resistance Is Low 8B–58. . . . . . . . . . . . . . . . . . . . . .
DTC 54 Driver Side Airbag Deployment Loop Is
Shorted To Ground 8B–60. . . . . . . . . . . . . . . . . . . . . .
DTC 55 Driver Side Airbag Deployment Loop Is
Shorted To Power 8B–62. . . . . . . . . . . . . . . . . . . . . . .
DTC 56 Passenger Side Airbag Deployment Loop
Resistance Is High 8B–64. . . . . . . . . . . . . . . . . . . . . .
DTC 57 Passenger Side Airbag Deployment Loop
Resistance Is Low 8B–66. . . . . . . . . . . . . . . . . . . . . .
DTC 58 Passenger Side Airbag Deployment Loop
Is Shorted To Ground 8B–68. . . . . . . . . . . . . . . . . . . .
DTC 59 Passenger Side Airbag Deployment Loop
Is Shorted To Power 8B–70. . . . . . . . . . . . . . . . . . . . .

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 3
DAEWOO V–121 BL4
SPECIFICATIONS
GENERAL SPECIFICATIONS
ApplicationDescription
Airbag System Deployment Time<20ms
Detection Time<5ms
Operating Temperature–40°C~+85°C
Storage Temperature–40°C~+90°C
Voltage Range9~16 V
Current consumption5ms after ignition switch ON <1A
5ms
5sec<300Ma, after 5sec.<100Ma
Acceleration Range+/– 50g
Maximum Acceleration+/– 600g pulse
Voltage Ramp0.2~2.0 V/s
Energy Reservation150ms after battery disconnection
Inflator Ignition Energy4.3mj
Squib Resistance2.15 +/– 0.35Ω
Airbag Warning Lamp ON Time(When Ignition ON)6sec
FASTENER TIGHTENING SPECIFICATIONS
ApplicationN·mLb–FtLb–In
Clock Spring Retaining Screws3–27
Driver Airbag Module Mounting Bolts11–97
Passenger Airbag Module Mounting Bolts8–71
Sensing and Diagnostic Module(SDM) Mounting Bolts10–89
SPECIAL TOOLS
SPECIAL TOOLS TABLE
Scan Tool

8B – 6ISUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO V–121 BL4
DIAGNOSIS
DIAGNOSTIC TROUBLE CODE (DTC)
When the sensing and diagnostic module (SDM) detects
any problem it illuminates the airbag warning indicator and
stores the diagnostic trouble codes (DTCs).
The supplemental inflatable restraints (SIR) diagnostic
system check must be always the starting point for any
SIR diagnosis. The diagnostic system check reveals diag-
nostic trouble codes (DTCs) through the use of scan tool.
It also checks for proper airbag warning lamp operation.
The two types of DTCs that may be recorded are as fol-lows :
1. Active DTCs represent malfunction being detected
during the current ignition cycle. Active DTCs are
stored in random access memory (RAM).
2. Historic DTCs represent malfunctions detected sin-
cethe last time the historic memory was cleared.
Historic DTCs are stored in the electrically erasable
programmable read–only memory (EPROM).
Diagnostic Trouble Code Table
DTCDescription
1Driver Airbag Deployment Loop Resistance Is High
2Driver Airbag Deployment Loop Resistance Is Low
3Driver Airbag Deployment Loop Is Shorted To Ground
4Driver Airbag Deployment Loop Is Shorted To Power
5Passenger Airbag Deployment Loop Resistance Is High
6Passenger Airbag Deployment Loop Resistance Is Low
7Passenger Airbag Deployment Loop Is Shorted To Ground
8 Passenger Airbag Deployment Loop Is Shorted To Power
9Driver Belt Pretensioner Deployment Loop Resistance Is High
10Driver Belt Pretensioner Deployment Loop Resistance Is Low
11Driver Belt Pretensioner Deployment Loop Is Shorted To Ground
12 Driver Belt Pretensioner Deployment Loop Is Shorted To Power
13Passenger Belt Pretensioner Deployment Loop Resistance Is High
14Passenger Belt Pretensioner Deployment Loop Resistance Is Low
15Passenger Belt Pretensioner Deployment Loop Is Shorted To Ground
16Passenger Belt Pretensioner Deployment Loop Is Shorted To Power
23Battery Voltage High
24 Battery Voltage Low
25 Airbag Warning Lamp Failure
31Internal Sensing Diagnostic Module(SDM) Failure
32 Airbag Inflation Record By Frontal Collision
33 Driver Side Airbag Inflation Record By Side Impact
34Passenger Side Airbag Inflation Record By Side Impact
35Belt Pretensioner Explosion Record
38Side Airbag And Belt Pretensioner Explosion Count Over 5
52 Driver Side Airbag Deployment Loop Resistance Is High
53Driver Side Airbag Deployment Loop Resistance Is Low
54Driver Side Airbag Deployment Loop Is Shorted To Ground
55 Driver Side Airbag Deployment Loop Is Shorted To Power
56Passenger Side Airbag Deployment Loop Resistance Is High

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 19
DAEWOO V–121 BL4
DTC 4
Driver Airbag Deployment Loop Is Shorted To Power
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute to discharge the SDM char-
ger.–Go to Step 2–
2Visually inspect the connector and the wiring of driv-
er airbag. Is the airbag wiring damaged?–Replace the
airbag wiring.Go to Step 3
31. Confirm the ignition switch ”OFF”.
2. Remove the driver airbag module.
3. Disconnect the connector of SDM wiring.
4. Check the resistance between the high, low
wiring of driver airbag module and the battery.
Is the resistance 10KΩ?10 KΩGo to Step 4Go to Step 5
41. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Erase the DTC using scan tool.
4. Perform the SIR Diagnostic System Check.
5. If the DTC is not removable, then replace the
driver airbag module.–––
51. Remove the connector from the clock spring
wiring.
2. Check the resistance between the high, low
wiring of clock spring and the battery. Is the
resistance 10KΩ?10 KΩReplace the
clock spring.Replace the
airbag wiring.

8B – 26ISUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO V–121 BL4
J3B18B04
1 2
21
SDM Driver Airbag Module
Clock SpringDK GRN/
WHT
BLK/WHT
G202
10 11146
Passenger Airbag Module
BRN
BRNDK BLU
WHT/
BLK
DK BLU
13
12
DIAGNOSTIC TROUBLE CODE (DTC) 8
PASSENGER AIRBAG DEPLOYMENT LOOP IS SHORTED
TO POWER
Circuit Description
When the ignition switch is turned to ON, the sensing and
diagnostic module(SDM) will perform turn–on test to diag-
nose critical malfunctions within SDM itself.
Upon passing these test ignition and deployment loop volt-
ages are measured to ensure that they are within their nor-
mal voltage ranges. The SDM monitors the voltages at the
driver low and the passenger low to detect shorts to
ground or voltage in the deploy loops.The SDM checks the wiring connection to the passenger
airbag module by letting the infinitesimal current flow
through the internal circuit and verify the resistance. If the
resistance is in the 2 kilo ohms between 10 kilo ohms, the
defect may occur depending upon SDM. The normal re-
sistance is over 10 kilo ohms.
DTC 8 Will Set When
S The airbag wiring of passenger’s high is shorted to
battery wiring.
S The airbag wiring of passenger’s low is shorted to
battery wiring.

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 27
DAEWOO V–121 BL4
DTC 8
Passenger Airbag Deployment Loop Is Shorted To Power
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute to discharge the SDM char-
ger.–Go to Step 2–
2Visually inspect the connector and the wiring of pas-
senger airbag. Is the airbag wiring damaged?–Replace the
airbag wiring.Go to Step 3
31. Confirm the ignition switch ”OFF”.
2. Remove the passenger airbag module.
3. Disconnect the connector of SDM wiring.
4. Check the resistance between the SDM and
the high, low wiring of passenger airbag mod-
ule and the battery. Is the resistance 10KΩ?10 KΩGo to Step 4Replace the
airbag wiring.
41. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Erase the DTC using scan tool.
4. Perform the SIR Diagnostic System Check.
5. If the DTC is not removable, then replace the
passenger airbag module.–––

8B – 34ISUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO V–121 BL4
J3B18B05
341 2
SDM Driver
Pretensioner
ModulePassenger
Pretensioner
Module
PNKPNK/
DK BLUDK BLU/
WHT BLK/WHT PPL YEL/
DK BLUDK BLU/
WHTRED/
BLK
DK
BLU
G202 C301
126 1
2
38 76
DIAGNOSTIC TROUBLE CODE (DTC) 12
DRIVER BELT PRETENSIONER DEPLOYMENT LOOP IS
SHORTED TO POWER
Circuit Description
When the ignition switch is turned to ON, the sensing and
diagnostic module(SDM) will perform turn–on test to diag-
nose critical malfunctions within SDM itself.
Upon passing these test ignition and deployment loop volt-
ages are measured to ensure that they are within their nor-
mal voltage ranges. The SDM monitors the voltages at the
driver low and the passenger low to detect shorts to
ground or voltage in the deploy loops.The SDM checks the wiring connection to the passenger
airbag module by letting the infinitesimal current flow
through the internal circuit and verify the resistance. If the
resistance is in the 2 kilo ohms between 10 kilo ohms, the
defect may occur depending upon SDM. The normal re-
sistance is over 10 kilo ohms.
DTC 12 Will Set When
S The belt pretensioner wiring of driver’s high is
shorted to battery wiring.
S The belt pretensioner wiring of driver’s low is
shorted to battery wiring.

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 35
DAEWOO V–121 BL4
DTC 12
Driver Belt Pretensioner Deployment Loop Is Shorted To
Power
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute to discharge the SDM char-
ger.–Go to Step 2–
2Visually inspect the connector and the wiring of air-
bag. Is the airbag wiring damaged?–Replace the
airbag wiring.Go to Step 3
3Check the resistance between the SDM and the
high, low wiring of driver belt pretensioner and the
battery. Is the resistance 10KΩ?
10K ΩGo to Step 4Replace the
airbag wiring.
41. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Erase the DTC using scan tool.
4. Perform the SIR Diagnostic System Check.
5. If the DTC is not removable, then replace the
driver belt pretensioner.–––

8B – 42ISUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO V–121 BL4
J3B18B05
341 2
SDM Driver
Pretensioner
ModulePassenger
Pretensioner
Module
PNKPNK/
DK BLUDK BLU/
WHT BLK/WHT PPL YEL/
DK BLUDK BLU/
WHTRED/
BLK
DK
BLU
G202 C301
126 1
2
38 76
DIAGNOSTIC TROUBLE CODE (DTC) 16
PASSENGER BELT PRETENSIONER DEPLOYMENT
LOOP IS SHORTED TO POWER
Circuit Description
When the ignition switch is turned to ON, the sensing and
diagnostic module(SDM) will perform turn–on test to diag-
nose critical malfunctions within SDM itself.
Upon passing these test ignition and deployment loop volt-
ages are measured to ensure that they are within their nor-
mal voltage ranges. The SDM monitors the voltages at the
driver low and the passenger low to detect shorts to
ground or voltage in the deploy loops.The SDM checks the wiring connection to the passenger
airbag module by letting the infinitesimal current flow
through the internal circuit and verify the resistance.
DTC 16 Will Set When
S The belt pretensioner wiring of passenger’s high is
shorted to battery wiring.
S The belt pretensioner wiring of passenger’s low is
shorted to battery wiring.

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 43
DAEWOO V–121 BL4
DTC 16
Passenger Belt Pretensioner Deployment Loop Is
Shorted Power
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute to discharge the SDM char-
ger.
3. Visually inspect the connector and the air wir-
ing.
Is the connector disconnected?–Connect the
connector.Go to Step 2
21. Check the resistance between the SDM and
the high, low wiring of passenger belt preten-
sioner and the battery.
Is the resistance 10KΩ?
10K ΩGo to Step 3Replace the
airbag wiring.
31. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Erase the DTC using scan tool.
4. Perform the SIR Diagnostic System Check.
Does the DTC still exist?–Go to Step 4System is OK.
4Replace the passenger belt pretensioner.–––