lock DAEWOO MATIZ 2003 Service Repair Manual

9P –30 DOORS
DAEWOO M-150 BL2
SCHEMATIC AND ROUTING DIAGRAMS
POWER DOOR LOCKS
(LEFT–HAND DRIVE)
D19C201B

DOORS 9P–31
DAEWOO M-150 BL2
POWER DOOR LOCKS
(RIGHT–HAND DRIVE)
D19C201S

9P –32 DOORS
DAEWOO M-150 BL2
POWER DOOR LOCKS
(W/ ANTI–THEFT CONTROL : LHD)
D19C201S

DOORS 9P–33
DAEWOO M-150 BL2
POWER DOOR LOCKS
(W/ ANTI–THEFT CONTROL : RHD)
D19C202S

9Q – 2 ROOF
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
ROOF
The roof is a one-piece painted metal unit which incorpo-
rates a single, solid headliner and two moldings, one on
each side of the vehicle’s roof.
The moldings, which enclose and hide the roof rail
seams, are serviceable as individual units.
The one-piece formed headliner, common to both the
notchback and the hatchback, consists of a molded sub-
strate covered with a foam-backed cloth facing. The
one-piece construction requires servicing the headliner
as a complete assembly.
MANUAL SUNROOF
The sunroof is

Intended to provide light and air through the roof of
the vehicle during the driving.

Built into the roof.

Made of glass.
SUN VISORS
The sun visors swing down or side in order to block out
glare. They also swing to the side when they are re-
leased from the support.
PASSENGER ASSIST HANDLE
There is a passenger assist handle for the front passen-
ger seat. Passengers can use these handles to assist in
keeping their balance over rough roads or during sharp
turns.
COAT HOOK
The coat hook is fastened to the headliner above the
left-hand rear passenger seat for Left–Hand Drive or
right hand rear passenger seat for Right–Hand Drive.
This position has a coat hook in the place of a passenger
assist handle.

ROOF 9Q–5
DAEWOO M-150 BL2
D109C557
MANUAL SUNROOF
Removal Procedure
1. Remove the sunroof screen.

Remove the clips (1).

Remove the lock (2).

Remove the screen (3).
D109C558
2. Remove the inside sunroof molding in the passenger
compartment.
a. Inside sunroof molding.
D109C559
3. Remove the lower sunroof frame.

Remove the screws (1).

Remove the lower sunroof frame (2).
D109C560
4. Remove the upper sunroof frame.
a. Upper sunroof frame.

9Q –6 ROOF
DAEWOO M-150 BL2
D19C561A
Installation Procedure
1. Install the upper sunroof frame.
2. Install the lower sunroof frame with the screws (a).
3. Install the inside sunroof molding.
4. Install the screen with the clips and the lock.
Tighten
Tighten the screws to 3 Nm (27 lb-in).
Notice: When installing the lower sunroof frame, make
sure to tighten the screws previously as shown the fig-
ure and tighten all the screws.
D109C562
SUN VISORS
Removal Procedure
1. Remove the sun visors.

Remove the screws (1).

Remove the sun visors (2).
D109C563
Installation Procedure
1. Install the sun visors with the screws.
D109C564
PASSENGER ASSIST HANDLE OR
THE COAT HOOK
Removal Procedure
1. Remove the passenger assist handle or the coat
hook from the headliner.

Remove the screws (1).

Remove the coat hook or the assist handle (2).

BODY FRONT END 9R–3
DAEWOO M-150 BL2
REPAIR INSTRUCTIONS
ON–VEHICLE SERVICE
D109C517
LUBRICATION
The hood hinges and the locking mechanisms require
periodic lubrication for proper operation. Refer to Sec-
tion 0B, General Information for the specific types and
intervals of lubrication.
D109C518
FASTENERS
Notice: Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use the correct
fasteners to prevent premature corrosion.
Many aluminum components are used on current models.
Aluminum in contact with steel may corrode rapidly if it is
not protected by special finishes or isolators.
The fasteners used have a special finish which provides
adequate protection from corrosion. These special fas-
teners differ in color in order to easily identify them from
the standard metric fasteners, which are medium blue in
color.
When replacing fasteners, avoid substituting otherwise
similar fasteners in the same location.
D109C519
ANTICORROSION MATERIALS
In order to provide rust resistance, anticorrosion materi-
als have been applied to the interior surfaces of most
of the metal panels. When you service these panels,
properly re-coat them with a service-type anticorrosion
material if any of the original material has been dis-
turbed.

9S –4 BODY REAR END
DAEWOO M-150 BL2
D109C549
3. Pry off the lower B–pillar trim panel. Refer to Section
9G, Interior Trim.
4. Pry off the rear rocker trim panel. Refer to Section to
9G, Interior Trim.
5. Pry off the luggage compartment wheelhouse trim
panel. Refer to Section to 9G, Interior Trim.
6. Remove the lock striker of the fuel filler.

Remove the lock striker by turning it rectangularly.
a. Lock striker
D19C550B
7. Remove the fuel filler door remote cable.

Remove the cable retaining strip.

Disconnect the fuel filler door remote cable (1).
D19C550C
Installation Procedure
1. Connect the fuel filler door remote cable to the fuel
filler door.
2. Retain the cable with the strip.
D19C549A
3. Install the lock striker of the fuel filler.
4. Install the luggage compartment wheelhouse trim
panel. Refer to Section 9G, Interior Trim.
5. Install the rear rocker trim panel. Refer to Section 9G,
Interior Trim.
6. Install the lower B–pillar trim panel. Refer to Section
9G, Interior Trim.

BODY REAR END 9S–5
DAEWOO M-150 BL2
D109C551
7. Connect the fuel filler door remote cable to the han-
dle.
8. Install the fuel filler door remote handle with the
screws.
D109C548
TAILGATE REMOTE CABLE AND
HANDLE
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Pry off the front rocker trim panel. Refer to Section
9G, Interior Trim.
2. Remove the tailgate remote handle.

Remove the screws (1).

Disconnect the cable (2).

Remove the tailgate remote handle (3).
D19C633A
3. Pry off the lower B–pillar trim panel. Refer to Section
9G, Interior Trim.
4. Pry off the rear rocker trim panel. Refer to Section
9G, Interior Trim.
5. Pry off the luggage compartment wheelhouse trim
panel. Refer to Section 9G, Interior Trim.
6. Disconnect the cable from the tailgate lock striker.
Refer to Section 9P, Doors.
7. Remove the tailgate remote cable.

Remove the cable retaining strip.

Disconnect the tailgate remote cable (1).
D109C551
Installation Procedure
1. Connect the tailgate remote cable to the tailgate lock
striker.
2. Retain the cable with the strip.
3. Install the luggage compartment wheelhouse trim
panel. Refer to Section 9G, Interior Trim.
4. Install the rear rocker trim panel. Refer to Section 9G,
Interior Trim.
5. Install the lower B–pillar trim panel. Refer to Section
9G, Interior Trim.
6. Connect the tailgate remote cable to the handle.
7. Install the tailgate remote handle with the screws.