cooling DAEWOO MATIZ 2003 Service Service Manual
[x] Cancel search | Manufacturer: DAEWOO, Model Year: 2003, Model line: MATIZ, Model: DAEWOO MATIZ 2003Pages: 1184, PDF Size: 36 MB
Page 332 of 1184
1F–234 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F090
DIAGNOSTIC TROUBLE CODE (DTC) – P0481 HIGH SPEED COOLING FAN
RELAY CIRCUIT FAULT (WITHOUT A/C)
Circuit Description
Ignition voltage is supplied directly to the cooling fan
relay coil. The engine control module(ECM) controls the
relay by grounding the control circuit via an internal
switch called a driver. The primary function of the driver
is supply the ground for the component being controlled.
Each driver has a fault line which is monitored by the
ECM. When the ECM is commanding a component ON,
the voltage of the control circuit should be low (near
0volts). When the ECM is commanding the control cir-
cuit to a component OFF, the voltage potential of the cir-
cuit should be high(near battery voltage). If the fault
detection circuit senses a voltage other than what is ex-
pected, the fault line status will change causing the DTC
to set.
The relay is used to control the high current flow to the
cooling fan motors. This allows the ECM driver to only
have to handle the relatively low current used by the
relay.
Conditions for Setting the DTC
Diagnostic Trouble Codes (DTCs) P0117, P0118 not
set.
Ignition ON.Ignition voltage is greater than 10 volts.
Engine run time is greater than 5 seconds.
Action Taken When The DTCs Sets
The Malfunction Indicator Lamp (MIL) will not illumi-
nate.
The ECM will store conditions which were present
when the DTC was set as Failure Records data only.
This information will not be stored in the Freeze
Frame data.
Conditions for Clearing the MIL/DTC
A history DTC will clear after 40 consecutive warm-up
cycles without a fault.
DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
Using Freeze Frame and/or failure records data may aid
in locating an intermittent condition. If the DTC cannot
be duplicated, the information included in the Freeze
Frame and/or failure records data can be useful in deter-
mining how many miles since the DTC set. The fail
counter and Pass Counter can also be used to deter-
mine how many ignition cycles the diagnostics reported
Page 333 of 1184
ENGINE CONTROLS 1F–235
DAEWOO M-150 BL2
a Freeze Frame conditions (rpm, load, vehicle speed, temperature, etc.) that .are noted. This will isolate when
the DTC failed.
DTC P0481 – High Speed Cooling Fan Relay Circuit Fault (without A/C)
StepActionValue(s)YesNo
1
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
1. Turn the ignition switch to ON with the engine
OFF.
2. Install a scan tool.
3. Command the relay ON and OFF.
Does the relay turn ON and OFF when
commanded?
–
Go to Step 3Go to Step 5
3
1. Turn the ignition switch to LOCK.
2. Disconnect the engine control module (ECM)
connector.
3. Turn the ignition switch to ON.
4. Using a digital voltmeter(DVM), measure the
current in high speed relay control circuit, at
terminal 5 to ground for 2 minutes.
Does the amperage measure less than the specified
value?
0.75 amps
Go to
“Diagnostic
Aids”
Go to Step 4
4
1. Turn the ignition switch to LOCK.
2. Disconnect the relay.
3. Using a DVM, measure the resistance between
terminals 85 and 5 in the relay control circuit in
the ECM harness connector to ground.
Does the DVM display infinite resistance?
–
Go to Step 12Go to Step 10
5
1. Turn the ignition switch to LOCK.
2. Disconnect the relay.
3. Connect a test light between the relay coil
terminals 86 and 85 in the relay harness
connector.
4. Turn the Turn the ignition switch to ON.
5. Using the scan tool, command the relay ON and
OFF.
Does the test light turn ON and OFF with each
commanded?
–
Go to Step 8Go to Step 6
6
With the test light connected to ground, probe the
ignition feed circuit in the relay harness connector.
Does the test light illuminate?
–
Go to Step 7Go to Step 11
7
1. Turn the ignition switch to LOCK.
2. Reconnect the relay.
3. Disconnect the ECM connector containing the
relay control circuit.
4. Turn the Turn the ignition switch to ON.
5. With a fused jumper wire connected to ground,
probe the relay control circuit at terminal 5 in the
ECM harness connector.
Does the relay operate?
–
Go to Step 9Go to Step 10
8Check the connections at the relay.
Is a problem found and corrected?–Go to Step 14Go to Step 12
Page 334 of 1184
1F–236 ENGINE CONTROLS
DAEWOO M-150 BL2
DTC P0481 – High Speed Cooling Fan Relay Circuit Fault (without A/C) (Cont’d)
StepActionValue(s)YesNo
9Check the connection at the ECM.
Is a problem found and corrected?–Go to Step 11Go to Step 13
10Repair the faulty relay control circuit.
Is the repair complete?–Go to Step 14–
11Repair the faulty relay ignition feed circuit.
Is the repair complete?–Go to Step 14–
12Replace the relay.
Is the replacement complete?–Go to Step 14–
13Replace the ECM.
Is the replacement complete?–Go to Step 14–
14
1. Using the scan tool, clear the Diagnostic Trouble
Codes (DTCs).
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting the DTC as specifiec in the supporting
text.
Does the scan tool indicate that this diagnostic ran
and passed?
–
Go to Step 15Go to Step 2
15
Check if any additional DTCs are set.
Are any DTCs displayed that have not been
diagnosed?
–
Go to
Applicable DTC
table
System OK
Page 336 of 1184
1F–238 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F270
DIAGNOSTIC TROUBLE CODE (DTC) – P0481 HIGH SPEED COOLING FAN
RELAY CIRCUIT FAULT (WITH A/C)
Circuit Description
Ignition voltage is supplied directly to the cooling fan
relay coil. The engine control module(ECM) controls the
relay by grounding the control circuit via an internal
switch called a driver. The primary function of the driver
is supply the ground for the component being controlled.
Each driver has a fault line which is monitored by the
ECM. When the ECM is commanding a component ON,
the voltage of the control circuit should be low (near
0volts). When the ECM is commanding the control cir-
cuit to a component OFF, the voltage potential of the cir-
cuit should be high(near battery voltage). If the fault
detection circuit senses a voltage other than what is ex-
pected, the fault line status will change causing the DTC
to set.
The relay is used to control the high current flow to the
cooling fan motors. This allows the ECM driver to only
have to handle the relatively low current used by the
relay.
Conditions for Setting the DTC
Diagnostic Trouble Codes (DTCs) P0117, P0118 not
set.
Ignition ON.Ignition voltage is greater than 10 volts.
Engine run time is greater than 5 seconds.
Action Taken When The DTCs Sets
The Malfunction Indicator Lamp (MIL) will not illumi-
nate.
The ECM will store conditions which were present
when the DTC was set as Failure Records data only.
This information will not be stored in the Freeze
Frame data.
Conditions for Clearing the MIL/DTC
A history DTC will clear after 40 consecutive warm-up
cycles without a fault.
DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
Using Freeze Frame and/or failure records data may aid
in locating an intermittent condition. If the DTC cannot
be duplicated, the information included in the Freeze
Frame and/or failure records data can be useful in deter-
mining how many miles since the DTC set. The fail
counter and Pass Counter can also be used to deter-
mine how many ignition cycles the diagnostics reported
Page 337 of 1184
ENGINE CONTROLS 1F–239
DAEWOO M-150 BL2
a Freeze Frame conditions (rpm, load, vehicle speed, temperature, etc.) that .are noted. This will isolate when
the DTC failed.
DTC P0481 – High Speed Cooling Fan Relay Circuit Fault (with A/C)
StepActionValue(s)YesNo
1
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
1. Turn the ignition switch to ON with the engine
OFF.
2. Install a scan tool.
3. Command the relay ON and OFF.
Does the relay turn ON and OFF when
commanded?
–
Go to Step 3Go to Step 5
3
1. Turn the ignition switch to LOCK.
2. Disconnect the engine control module (ECM)
connector.
3. Turn the ignition switch to ON.
4. Using a digital voltmeter(DVM), measure the
current in high speed relay control circuit, at
terminal 39 to ground for 2 minutes.
Does the amperage measure less than the specified
value?
0.75 amps
Go to
“Diagnostic
Aids”
Go to Step 4
4
1. Turn the ignition switch to LOCK.
2. Disconnect the relay.
3. Using a DVM, measure the resistance between
terminals 85 and 39 in the high speed cooling fan
relay control circuit in the ECM harness connector
to ground.
Does the DVM display infinite resistance?
–
Go to Step 12Go to Step 10
5
1. Turn the ignition switch to LOCK.
2. Disconnect the relay.
3. Connect a test light between the relay coil
terminals 86 and 85 in the relay harness
connector.
4. Turn the Turn the ignition switch to ON.
5. Using the scan tool, command the relay ON and
OFF.
Does the test light turn ON and OFF with each
commanded?
–
Go to Step 8Go to Step 6
6
With the test light connected to ground, probe the
ignition feed circuit in the relay harness connector.
Does the test light illuminate?
–
Go to Step 7Go to Step 11
7
1. Turn the ignition switch to LOCK.
2. Reconnect the relay.
3. Disconnect the ECM connector containing the
relay control circuit.
4. Turn the Turn the ignition switch to ON.
5. With a fused jumper wire connected to ground,
probe the relay control circuit at terminal 10 in the
ECM harness connector.
Does the relay operate?
–
Go to Step 9Go to Step 10
Page 338 of 1184
1F–240 ENGINE CONTROLS
DAEWOO M-150 BL2
DTC P0481 – High Speed Cooling Fan Relay Circuit Fault (with A/C) (Cont’d)
StepActionValue(s)YesNo
8Check the connections at the relay.
Is a problem found and corrected?–Go to Step 14Go to Step 12
9Check the connection at the ECM.
Is a problem found and corrected?–Go to Step 11Go to Step 13
10Repair the faulty relay control circuit.
Is the repair complete?–Go to Step 14–
11Repair the faulty relay ignition feed circuit.
Is the repair complete?–Go to Step 14–
12Replace the relay.
Is the replacement complete?–Go to Step 14–
13Replace the ECM.
Is the replacement complete?–Go to Step 14–
14
1. Using the scan tool, clear the Diagnostic Trouble
Codes (DTCs).
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting the DTC as specifiec in the supporting
text.
Does the scan tool indicate that this diagnostic ran
and passed?
–
Go to Step 15Go to Step 2
15
Check if any additional DTCs are set.
Are any DTCs displayed that have not been
diagnosed?
–
Go to
Applicable DTC
table
System OK
Page 348 of 1184
1F–250 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F300
DIAGNOSTIC TROUBLE CODE (DTC) – P1535 EVAPORATOR TEMPERATURE
SENSOR HIGH VOLTAGE
Circuit Description
A semiconductor which resistance is noticeably
changed as the change of temperature. When the refrig-
erant temperature of the evaporator drops to 0°C (0°F)
and below, the evaporator cores get stuck with frost or
ice, reducing the airflow, lowering the cooling capacity.
The thermistor is a sensor which is used to prevent from
frosting or icing. The thermistor is installed on the evap-
orator.
Conditions for Setting the DTC
A short to battery voltage condition exists and is pres-
ent for more the 2 seconds.
Action Taken When the DTC Sets
The ECM will not illuminate the Malfunction Indicator
Lamp (MIL).A history DTCs is stored.
The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored
Failure Records buffers.
The A/C compressor operation will be disabled while
the low voltage indication exists.
Update the fail record each time the diagnostic test
fail.
Conditions for Clearing the MIL/DTC
A history DTC will clear after 40 consecutive warm-up
cycles without a fault.
Usisng the scan tool can clear DTC(s).
Disconnecting the ECM battery feed for 10 seconds.
Page 350 of 1184
1F–252 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F300
DIAGNOSTIC TROUBLE CODE (DTC) – P1536 EVAPORATOR TEMPERATURE
SENSOR LOW VOLTAGE
Circuit Description
A semiconductor which resistance is noticeably
changed as the change of temperature. When the refrig-
erant temperature of the evaporator drops to 0°C (0°F)
and below, the evaporator cores get stuck with frost or
ice, reducing the airflow, lowering the cooling capacity.
The thermistor is a sensor which is used to prevent from
frosting or icing. The thermistor is installed on the evap-
orator.
Conditions for Setting the DTC
A short to battery voltage condition exists and is pres-
ent for more the 2 seconds.
Action Taken When the DTC Sets
The ECM will not illuminate the Malfunction Indicator
Lamp (MIL).A history DTCs is stored.
The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored
Failure Records buffers.
The A/C compressor operation will be disabled while
the low voltage indication exists.
Update the fail record each time the diagnostic test
fail.
Conditions for Clearing the MIL/DTC
A history DTC will clear after 40 consecutive warm-up
cycles without a fault.
Usisng the scan tool can clear DTC(s).
Disconnecting the ECM battery feed for 10 seconds.
Page 388 of 1184
1F–290 ENGINE CONTROLS
DAEWOO M-150 BL2
DETONATION/SPARK KNOCK
StepActionValue(s)YesNo
1
Were the Important Preliminary Checks performed?
–
Go to Step 2
Go to
“Important
Preliminary
Checks”
2
1. Fill the fuel tank with a known good grade of
gasoline that has the octane rating of the value
specified.
2. Reevaluate the vehicle’s performance.
Does the detonation problem still exist?
91 octaneGo to Step 3System OK
3
1. Inspect for low engine coolant level.
2. Check for restricted airflow to the radiator or
restricted coolant flow.
3. Check for a faulty thermostat.
4. Check for an incorrect coolant solution.
Is the problem found?
–
Go to Step 4Go to Step 5
4
Repair or replace any cooling system components
as needed.
Is the repair complete?
–
System OK
–
5
1. Check the engine coolant temperature using the
scan tool.
2. Replace the Engine Coolant Temperature (ECT)
sensor if the resistance is not within specifications
as listed in the Diagnostic Aids for diagnostic
trouble code P0118.
Is the problem found?
–
Go to Step 6Go to Step 7
6
Replace the ECT sensor or repair the circuit as
needed.
Is the repair complete?
–
System OK
–
7
1. Check the ignition system output with a spark
tester.
2. Inspect the spark plugs for the proper heat range
and gap.
3. Check for the proper operation of the ignition
controls.
Is the ignition system operating properly?
–
Go to Step 9Go to Step 8
8
Repair or replace the ignition system components as
needed.
Is the repair complete?
–
System Ok
–
9
1. Connect the scan tool to the Data Link Connector
(DLC).
2. Road test the vehicle at the speed of the
complaint.
3. Monitor the long term fuel trim reading from the
scanner data stream.
Is the long term fuel trim reading above the value
specified?
25%
Go to
“Diagnostic Aids
for DTC P0171”
Go to Step 10
10Check the fuel system pressure.
Is the problem found?380 kPa
(55 psi)
Go to Step 11Go to Step 12
11
Repair or replace the fuel system components as
needed.
Is the repair complete?
–
System OK
–
Page 409 of 1184
ENGINE CONTROLS 1F–311
DAEWOO M-150 BL2
MAA1F450
2. Remove the MAP sensor.
Remove the bolts (1).
Remove the MAP sensor with bracket (2).
MAA1F460
Installatin Procedure
1. Install in the reverse order of removal.
Inspect the MAP sensor vacuum hose for the tear
and damages.
2. Install the MAP sensor with the bolts and nuts.
Tighten
Tighten the MAP sensor bolts/nuts to 8–12 Nm
(71–106 lb-in).
Tighten the MAP sensor bracket bolt to 8–12 Nm
(71–106 lb-in).
D102F537
THROTTLE BODY
Removal Procedure
1. Remove the air cleaner/resonator assembly and air
intake tube. Refer to Section 1B, SOHC Engine Me-
chanical.
2. Drain the engine coolant. Refer to Section 1D, Engine
Cooling.
D102F538
3. Disconnect the throttle cable, the throttle position
sensor and the idle air control valve connectors.
Open the throttle valve (1).
Disconnect the throttle cable (2).
Disconnect the idle air control valve connector (3).
Disconnect the throttle position sensor connector
(4).