Oil DAEWOO MATIZ 2003 Service Workshop Manual

ENGINE CONTROLS 1F–107
DAEWOO M-150 BL2
DTC P0171 – Fuel Trim System Too Lean
StepActionValue(s)YesNo
1
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
1. Install the scan tool to the Data Link Connector
(DLC).
2. Turn the ignition ON.
Are any component related Diagnostic Trouble
Codes (DTCs) set?
–Go to
Applicable DTC
table
Go to Step 3
3
With the engine running, operate the vehicle until the
LOOP STATUS indicates closed.
Is the Long Term Fuel Trim value below the
specified value?
–22%Go to Step 4Go to Step 5
4
1. Turn the ignition switch ON, with the engine OFF.
2. Review the Freeze Frame data and note the
parameters.
3. Operate the vehicle within the Freeze Frame
conditions and Conditions for Setting The DTC as
noted.
Does the Long Term Fuel Trim value go below the
specified value while operating under the specified
conditions?
–22%Go to Step 16Go to Step 5
5
Visually/physically check the following items:

Vacuum hoses for splits, kinks and improper
connections.

Crankcase ventilation oil/air separator for proper
installation.

Exhaust system for corrosion, leaks, loose or
missing hardware.

Oxygen sensor (O2S) is installed securely and
the pigtail harness is not contacting exhaust
manifold or engine.

Fuel for excessive water, alcohol, or other
contaminants.

Engine Control Module (ECM) and sensor
grounds are clean, tight, and in their proper
locations.
Do any of the above checks isolate a condition
requiring repair?
–
Go to Step 7Go to Step 6
6
1. Disconnect the Manifold Absolute Pressure
(MAP) sensor electrical connector.
2. Operate the vehicle in Closed Loop while
monitoring the Long Term Fuel Trim value.
Is the Long Term Fuel Trim value below the
specified value?
–22%Go to Step 15Go to Step 9
7
1. Repair the malfunction found in Step 5.
2. Recheck the Long Term Fuel Trim value while
operating the engine.
Is the Long Term Fuel Trim value below the
specified value?
–22%Go to Step 8Go to Step 9
8
Lean condition is not present.
Does a driveability problem exist?
–
Go to
“Symptom
Diagnosis”
Go to Step 16

ENGINE CONTROLS 1F–137
DAEWOO M-150 BL2
DTC P0300 – Multiple Cylinder Misfire (Cont’d)
StepActionValue(s)YesNo
18
Repair the open or the shorted fuel injector driver
circuit.
Is the repair complete?
–
Go to Step 27
–
19
Repair the open ignition feed circuit between the fuel
injector harness connector and the fuel injector
connector.
Is the repair complete?
–
Go to Step 27
–
20
Measure the resistance of the spark plug cable that
the spark plug tester did not spark.
Is the resistance of the spark plug cable less than
the specified value?
30000ΩGo to Step 21Go to Step 25
21
Inspect the Engine Control Module (ECM) connector
and connections.
Are the connections OK?
–
Go to Step 22Go to Step 23
22
Check the affected cylinders ignition control circuit
for an open or short and repair as necessary.
Is the repair complete?
–
Go to Step 27Go to Step 26
23Repair the connector or connections.
Is the repair complete?–Go to Step 27–
24
1. Turn the ignition OFF.
2. Replace the ECM.
Is the repair complete?
–
Go to Step 27
–
25Replace the spark plug cable.
Is the repair complete?–Go to Step 27–
26Replace the faulty ignition coil.
Is the repair complete?–Go to Step 27Go to Step 24
27
1. Using the scan tool, clear the DTCs.
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting this DTC as supported in the text.
Does the scan tool indicate that this diagnostic ran
and passed?
–
Go to Step 28Go to Step 2
28
Check if any additional DTCs are set.
Are any DTCs displayed that have not been
diagnosed?
–
Go to
Applicable DTC
table
System OK

ENGINE CONTROLS 1F–141
DAEWOO M-150 BL2
DTC P0300 – Multiple Cylinder Misfire (Cont’d)
StepActionValue(s)YesNo
16Replace any malfunctioning fuel injectors.
Is the repair complete?–Go to Step 27–
17
Check the affected fuel injector driver circuit at
terminals 90, 58, and 89 for an open, short, or short
to voltage.
Is a problem found?
–
Go to Step 18Go to Step 24
18
Repair the open or the shorted fuel injector driver
circuit.
Is the repair complete?
–
Go to Step 27
–
19
Repair the open ignition feed circuit between the fuel
injector harness connector and the fuel injector
connector.
Is the repair complete?
–
Go to Step 27
–
20
Measure the resistance of the spark plug cable that
the spark plug tester did not spark.
Is the resistance of the spark plug cable less than
the specified value?
30000ΩGo to Step 21Go to Step 25
21
Inspect the Engine Control Module (ECM) connector
and connections.
Are the connections OK?
–
Go to Step 22Go to Step 23
22
Check the affected cylinders ignition control circuit
for an open or short and repair as necessary.
Is the repair complete?
–
Go to Step 27Go to Step 26
23Repair the connector or connections.
Is the repair complete?–Go to Step 27–
24
1. Turn the ignition OFF.
2. Replace the ECM.
Is the repair complete?
–
Go to Step 27
–
25Replace the spark plug cable.
Is the repair complete?–Go to Step 27–
26Replace the faulty ignition coil.
Is the repair complete?–Go to Step 27Go to Step 24
27
1. Using the scan tool, clear the DTCs.
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting this DTC as supported in the text.
Does the scan tool indicate that this diagnostic ran
and passed?
–
Go to Step 28Go to Step 2
28
Check if any additional DTCs are set.
Are any DTCs displayed that have not been
diagnosed?
–
Go to
Applicable DTC
table
System OK

1F–160 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F200
DIAGNOSTIC TROUBLE CODE (DTC) – P0351 IGNITION SIGNAL COIL A FAULT
Circuit Description
The engine control module (ECM) provides a ground for
the electronic spark timing 1 circuit. When the ECM re-
moves the ground path of the ignition primary coil, the
magnetic field produced by the coil collapses. The col-
lapsing magnetic field produces a voltage in the secon-
dary coil which fires the spark plug. The circuit between
the ECM and the electronic ignition system is monitored
for an open circuit, short to voltage, and low voltage.
When the ECM detects a problem in the spark timing 1
circuit, it will set DTC P0351.
Conditions for Setting the DTC

This DTC can be stored in “key-on” status.

Time of fault fall occurrence is greater than time of the
DIS fall occurrence.
Must receive more than 40 failure within 80 test
cycles.
Action Taken When the DTC Sets

The Malfunction Indicator Lamp (MIL) will illuminate.

The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Freeze Frame and Failure Records buffers.

A history DTC is stored.
Conditions for Clearing the MIL/DTC

The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.

A history DTC will clear after 40 consecutive warm-up
cycles without a fault.

ENGINE CONTROLS 1F–161
DAEWOO M-150 BL2

DTC(s) can be cleared by using the scan tool.

Disconnecting the ECM battery feed for more than 10
seconds.
DIAGNOSTIC AIDS
Check and correct any abnormal engine noise before
using the diagnostic table.
Any circuitry that is suspected as causing engine noise
complaint should be thoroughly checked for the follow-
ing conditions :
Backed-out terminals.

Improper mating.

Broken locks.

Improperly formed.

Damaged terminals.

Poor terminal-to-wire connections.

Physical damage to the wiring harness.
DTC P0351 – Ignition Signal Coil A Fault
StepActionValue(s)YesNo
1
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
Check for a faulty connection or a damaged terminal
1 at the ignition coil.
Is a problem found?
–
Go to Step 8Go to Step 3
3
Check for a faulty connection or a damaged terminal
31 at the engine control module(ECM) connector.
Is the problem found?
–
Go to Step 8Go to Step 4
4
1. Turn the ignition switch to LOCK.
2. Disconnect the ECM.
3. Check the ignition control circuit for a short to
ground.
Is the problem found?
–
Go to Step 8Go to Step 5
5
Check the ignition control circuit for a short to
battery voltage.
Is the problem found?
–
Go to Step 8Go to Step 6
6Check for an open in the ignition control.
Is the problem found?–Go to Step 8Go to Step 7
7Replace the ECM.
Is the replacement complete?–Go to Step 8–
8
1. Using the scan tool, clear the Diagnostic Trouble
Codes(DTCs).

Start the engine and Idle at normal operating
temperature.

Operate the vehicle within the conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic ran
and passed?
–
Go to Step 9
–
9
Check if any additional DTCs are set.
Are any DTCs displayed that have not been
diagnosed?
–
Go to
Applicable DTC
table
System OK

1F–162 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F200
DIAGNOSTIC TROUBLE CODE (DTC) – P0352 IGNITION SIGNAL COIL B FAULT
Circuit Description
The engine control module (ECM) provides a ground for
the electronic spark timing 3 circuit. When the ECM re-
moves the ground path of the ignition primary coil, the
magnetic field produced by the coil collapses. The col-
lapsing magnetic field produces a voltage in the secon-
dary coil, which fires the spark plug. The circuit between
the ECM and the electronic ignition system is monitored
for an open circuit, short to voltage, and low voltage.
When the ECM detects a problem in the spark timing 3
circuit, it will set DTC P0352.
Conditions for Setting the DTC

This DTC can be stored in “key-on” status.

Time of fault fall occurrence is greater than time of the
DIS fall occurrence.
Must receive more than 40 failure within 80 test
cycles.
Action Taken When The DTCs Sets

The Malfunction Indicator Lamp (MIL) will illuminate.

The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Freeze Frame and failure records buffers.

A history DTC is stored.

The ECM will default to 6 degree timing.
Conditions for Clearing the MIL/DTC

The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.

ENGINE CONTROLS 1F–163
DAEWOO M-150 BL2

A history DTC will clear after 40 consecutive warm up
cycles without a fault.

Using the scan tool can clear DTC(s).

Disconnecting the ECM battery feed for 10 seconds.
DIAGNOSTIC AIDS
Check and correct any abnormal engine noise before
using the diagnostic table.
Any circuitry that is suspected as causing engine noise
complaint should be thoroughly checked for the follow-
ing conditions :
Backed-out terminals.

Improper mating.

Broken locks.

Improperly formed.

Damaged terminals.

Poor terminal-to-wire connections.

Physical damage to the wiring harness.
DTC P0352 – Ignition Signal Coil B Fault
StepActionValue(s)YesNo
1
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
Check for a faulty connection or a damaged terminal
3 at the ignition coil.
Is a problem found?
–
Go to Step 8Go to Step 3
3
Check for a faulty connection or a damaged terminal
32 at the engine control module(ECM) connector.
Is the problem found?
–
Go to Step 8Go to Step 4
4
1. Turn the ignition switch to LOCK.
2. Disconnect the ECM.
3. Check the ignition control circuit for a short to
ground
Is the problem found?
–
Go to Step 8Go to Step 5
5
Check the ignition control circuit for a short to
battery voltage.
Is the problem found?
–
Go to Step 8Go to Step 6
6Check for an open in the ignition control.
Is the problem found?–Go to Step 8Go to Step 7
7Replace the ECM.
Is the replacement complete?–Go to Step 8–
8
1. Using the scan tool, clear the Diagnostic Trouble
Codes(DTCs).

Start the engine and Idle at normal operating
temperature.

Operate the vehicle within the conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic ran
and passed?
–
Go to Step 9
–
9
Check if any additional DTCs are set.
Are any DTCs displayed that have not been
diagnosed?
–
Go to
Applicable DTC
table
System OK

1F–164 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F200
DIAGNOSTIC TROUBLE CODE (DTC) – P0353 IGNITION SIGNAL COIL C FAULT
Circuit Description
The engine control module (ECM) provides a ground for
the electronic spark timing 3 circuit. When the ECM re-
moves the ground path of the ignition primary coil, the
magnetic field produced by the coil collapses. The col-
lapsing magnetic field produces a voltage in the secon-
dary coil, which fires the spark plug. The circuit between
the ECM and the electronic ignition system is monitored
for an open circuit, short to voltage, and low voltage.
When the ECM detects a problem in the spark timing 3
circuit, it will set DTC P0352.
Conditions for Setting the DTC

This DTC can be stored in “key-on” status.

Time of fault fall occurrence is greater than time of the
DIS fall occurrence.
Must receive more than 40 failure within 80 test
cycles.
Action Taken When The DTCs Sets

The Malfunction Indicator Lamp (MIL) will illuminate.

The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Freeze Frame and failure records buffers.

A history DTC is stored.

The ECM will default to 6 degree timing.
Conditions for Clearing the MIL/DTC

The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.

ENGINE CONTROLS 1F–165
DAEWOO M-150 BL2

A history DTC will clear after 40 consecutive warm up
cycles without a fault.

Using the scan tool can clear DTC(s).

Disconnecting the ECM battery feed for 10 seconds.
DIAGNOSTIC AIDS
Check and correct any abnormal engine noise before
using the diagnostic table.
Any circuitry that is suspected as causing engine noise
complaint should be thoroughly checked for the follow-
ing conditions :
Backed-out terminals.

Improper mating.

Broken locks.

Improperly formed.

Damaged terminals.

Poor terminal-to-wire connections.

Physical damage to the wiring harness.
DTC P0353 – Ignition Signal Coil C Fault
StepActionValue(s)YesNo
1
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
Check for a faulty connection or a damaged terminal
3 at the ignition coil.
Is a problem found?
–
Go to Step 8Go to Step 3
3
Check for a faulty connection or a damaged terminal
32 at the engine control module(ECM) connector.
Is the problem found?
–
Go to Step 8Go to Step 4
4
1. Turn the ignition switch to LOCK.
2. Disconnect the ECM.
3. Check the ignition control circuit for a short to
ground
Is the problem found?
–
Go to Step 8Go to Step 5
5
Check the ignition control circuit for a short to
battery voltage.
Is the problem found?
–
Go to Step 8Go to Step 6
6Check for an open in the ignition control.
Is the problem found?–Go to Step 8Go to Step 7
7Replace the ECM.
Is the replacement complete?–Go to Step 8–
8
1. Using the scan tool, clear the Diagnostic Trouble
Codes(DTCs).

Start the engine and Idle at normal operating
temperature.

Operate the vehicle within the conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic ran
and passed?
–
Go to Step 9
–
9
Check if any additional DTCs are set.
Are any DTCs displayed that have not been
diagnosed?
–
Go to
Applicable DTC
table
System OK

1F–226 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F090
DIAGNOSTIC TROUBLE CODE (DTC) – P0480 LOW SPEED COOLING FAN
RELAY CIRCUIT FAULT (WITHOUT A/C)
Circuit Description
Ignition voltage is supplied directly to the cooling fan
relay coil. The engine control module(ECM) controls the
relay by grounding the control circuit via an internal
switch called a driver. The primary function of the driver
is supply the ground for the component being controlled.
Each driver has a fault line which is monitored by the
ECM. When the ECM is commanding a component ON,
the voltage of the control circuit should be low (near
0volts). When the ECM is commanding the control cir-
cuit to a component OFF, the voltage potential of the cir-
cuit should be high(near battery voltage). If the fault
detection circuit senses a voltage other than what is ex-
pected, the fault line status will change causing the DTC
to set.
The relay is used to control the high current flow to the
cooling fan motors. This allows the ECM driver to only
have to handle the relatively low current used by the
relay.
Conditions for Setting the DTC

Diagnostic Trouble Codes (DTCs) P0117, P0118 not
set.

Ignition ON.
Ignition voltage is greater than 10 volts.

Engine run time is greater than 5 seconds.
Action Taken When the DTC Sets

The Malfunction Indicator Lamp (MIL) will not illumi-
nate.

The ECM will store conditions which were present
when the DTC was set as Failure Records data only.

This information will not be stored in the Freeze
Frame data.
Conditions for Clearing the MIL/DTC

A history DTC will clear after 40 consecutive warm-up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
Using Freeze Frame and/or failure records data may aid
in locating an intermittent condition. If the DTC cannot
be duplicated, the information included in the Freeze
Frame and/or failure records data can be useful in deter-
mining how many miles since the DTC set. The fail
counter and Pass Counter can also be used to deter-
mine how many ignition cycles the diagnostics reported