brakes DAEWOO MATIZ 2003 Service Repair Manual

SECTION INDEX
FRONT MATTER
0A
GENERAL INFORMATION
0B
ENGINE1
SERVICE
MATIZ
FOREWORD
This manual includes procedure for maintenance,
adjustment, service operation and removal and
installation of components.
All information, illustrations and specifications con-
tained in this manual are based on the latest prod-
uct information available at the time of manual ap-
proval.
The right is reserved to make changes at any time
without notice.
DAEWOO MOTOR CO., LTD.
INCHON, KOREA
MANUAL
SUSPENSION
2
DRIVELINE/AXLE 3
BRAKES
4
TRANSAXLE
5
STEERING
6
RESTRAINTS
8
BODY AND ACCESSORIES9 7 HVAC
(HEATING, VENTILATION,
AND AIR CONDITIONING)
(MY2003)

BRAKES
CONTENTS
SECTION 4A HYDRAULIC BRAKES
SECTION 4B MASTER CYLINDER
SECTION 4C POWER BOOSTER
SECTION 4D FRONT DISC BRAKES
SECTION 4E REAR DRUM BRAKES
SECTION 4F ANTILOCK BRAKE SYSTEM
SECTION 4G PARKING BRAKE

1A–6 GENERAL ENGINE INFORMATION
DAEWOO M-150 BL2
GENERAL DIAGNOSIS (Cont’d)
 Condition Probable cause Correction
Hard Starting (WithOthers
Broken timing belt.
Replace the belt.
normal cranking)
Malfunction of Positive
Crankcase Ventilation (PCV)
valve.
Check and replace Positive
Crankcase Ventilation (PCV)
valve if needed.

Loosening, damage or
leakage of the vacuum hose.
Connect the hose correctly
or replace it.

Leakage of intake system.
Replace intake system.
Lack of Engine PowerDecline of
Compression
Pressure
Refer to “Page 1A–5”.
Refer to “Page 1A–5”.
Malfunction of
Improper ignition timing.
Adjust the ignition timing.
Ignition System
Faulty spark plug.
Adjust or replace the spark
plug.

Malfunction of the distributor.
Repair or replace the
distributor. Check the rotor.

Electric leakage or poor
connection of the high
tension cable.
Connect the cable correctly
or replace it.
Malfunction of
Clogged fuel pipe.
Clean the pipe.
Fuel System
Clogged or contaminated
fuel filter.
Replace the filter.
Others
Clogged exhaust system.
Check and repair the
system.

Clogged or contaminated air
cleaner element.
Clean or replace the air
cleaner element.

Leak of the intake manifold
gasket.
Replace the gasket.

Dragging brakes.
Repair or replace the
brakes.

Slipping clutch.
Adjust or replace the clutch.
Rough Engine IdlingDecline of
Compression
Pressure
Refer to “Page 1A–5”.
Refer to “Page 1A–5”.
Malfunction of
Clogged fuel pipe.
Clean the pipe.
Fuel System
Clogged or contaminated
fuel filter.
Replace the filter.

Malfunction of the fuel
pressure regulator.
Replace the regulator.
Malfunction of
Ignition System
Malfunction of the spark
plug.
Adjust or replace the spark
plug.

Electric leakage or poor
connection of the high
tension cable.
Connect the cable correctly
or replace it.

Worn distributor cap terminal
or accumulated carbon in
the distributor cap.
Replace or clean the
distributor cap.

1F–296 ENGINE CONTROLS
DAEWOO M-150 BL2
POOR FUEL ECONOMY
Definition: Fuel economy, as measured by an actual
road test, is noticeably lower than expected. Also, fuel
economy is noticeably lower than it was on this vehicle
at one time, as previously shown by an actual road test.
Important: Driving habits affect fuel economy. Check
the owner’s driving habits by asking the following ques-
tions:1. Is the A/C system (i.e. defroster mode) turned on all
the time?
2. Are the tires at the correct air pressure?
3. Have excessively heavy loads been carried?
4. Does the driver accelerate too much and too often?
Suggest the driver read the section in the owner’s
manual about fuel economy.
StepActionValue(s)YesNo
1
Were the Important Preliminary Checks performed?
–
Go to Step 2
Go to
“Important
Preliminary
Checks”
2
1. Inspect the air filter for excessive contamination.
2. Inspect for fuel system leaks.
Are all needed checks complete?
–
Go to Step 3
–
3
1. Inspect the spark plugs for excessive wear,
insulation cracks, improper gap, or heavy
deposits.
2. Replace any faulty spark plugs.
3. Inspect the ignition wires for cracking, hardness,
and proper connections.
Are all needed checks and repairs complete?
–
Go to Step 4
–
4
1. Inspect the engine coolant level.
2. Check the thermostat for being always open or for
an incorrect heat range.
3. Replace the thermostat as needed.
Are all needed checks and repairs complete?
–
Go to Step 4
–
5
1. Check the transaxle shift pattern. Ensure all
transaxle gears are functioning.
2. Check for proper calibration of the speedometer.
3. Check the brakes for dragging.
4. Check the cylinder compression.
5. Repair, replace, or adjust any components as
needed.
Are all checks and needed repairs complete?
–
System OK
–

2A–2 SUSPENSION DIAGNOSIS
DAEWOO M-150 BL2
Condition Probable Cause Correction
Car Lead/Pull
Mismatched or uneven tires.
Replace the tires.

A broken or a sagging coil spring.
Replace the coil spring.

A improperly radial tire lateral force.
Check the wheel alignment.

Switch the tire and wheel assemblies.

Replace the tires as needed.

The front–wheel alignment is
out–of–align.
Align the front wheels.

Off–center steering gear.
Reseat the pinion valve assembly.

Replace the pinion valve assembly as
needed.

Front–brake dragging.
Adjust the front brakes.
Abnormal or Excessive
Tire Wear
The front–wheel and rear–wheel
alignment is out–of–align.
Align the front and the rear wheels.

Excessive toe.
Adjust the toe.

A broken or a sagging coil spring.
Replace the coil spring.

Out–of–balance tires.
Balance the tires.

Worn strut dampeners.
Replace the strut dampeners.

A failure to rotate tires.
Rotate the tires.

Replace the tires as needed.

Overloaded vehicle.
Maintain the proper load weight.

Low tire inflation.
Inflate the tires to the proper pressure.
Scuffed Tires
Incorrect toe.
Adjust the toe.

A twisted or a bent suspension arm.
Replace the suspension arm.
Wheel Tramp
An out–of–balance tire or wheel.
Balance the tire or the wheel.

Improper strut dampener action.
Replace the strut dampeners.
Shimmy, Shake, or
An out–of–balance tire or wheel.
Balance the tire or the wheel.
Vibration
Excessive wheel hub runout.
Measure the hub flange runout.

Replace the hub as needed.

Excessive brake drum or brake rotor
imbalance.
Adjust the brakes.

Replace the brake rotor or the brake
drum as needed.

Worn tie rod ends.
Replace the tie rod ends.

Wheel trim imbalance.
Balance the wheel.

A worn ball joint.
Replace the control arm and ball joint
assembly.

Excessive wheel runout.
Measure the wheel runout.

Replace the wheel as needed.

Excessive loaded radial runout on the
tire and wheel assembly.
Match–mount the tire and wheel
assembly.

FRONT SUSPENSION 2C–9
DAEWOO M-150 BL2
D106B507
4. Remove the control arm from the knuckle assembly.

Remove the stud bolt (1).

Separate the control arm from the knuckle assem-
bly (2).
D106B508
5. Remove the brake caliper from the knuckle assembly.
Refer to Section 4D, Front Disc Brakes.
6. Remove the ABS wheel speed sensor from the
knuckle assembly, if applicable. Refer to Section 4F,
Anti–lock Brake System.
7. Remove the steering knuckle assembly from the ve-
hicle.

Remove the strut bracket bolts (1).

Separate the knuckle assembly from the drive
shaft by pulling the steering knuckle assembly (2).
D16B509A
70–90 Nm
50–70 Nm
Installation Procedure
1. Install in the reverse order of removal.
2. Install the steering knuckle assembly in the vehicle
with strut bracket bolts (1).
Tighten
Tighten the strut bracket bolts to 70–90 Nm (52–66
lb-ft).
3. Install the brake caliper from the knuckle assembly.
4. Install the control arm into the knuckle assembly with
the stud bolt (2).
Tighten
Tighten the stud bolt to 50–70 Nm (36–52 lb-ft).
D16B510B
5. Install the tie rod end to the knuckle assembly.
6. Install the tie rod end–to–knuckle castellated nut (1)
and the cotter pin.
Tighten
Tighten the castellated nut to 30–55 Nm (22–41 lb-
ft).
7. Install the caulking nut (2).

Bend the caulking nut flange (3).
Tighten
Tighten the caulking nut to 210 Nm (155 lb-ft).

REAR SUSPENSION 2D–9
DAEWOO M-150 BL2
D16C515A
Installation Procedure
1. Install the trailing arm.

Install the trailing arm–to–body bracket bolt (1).
Tighten
Tighten the trailing arm–to–body bracket bolt to 70–
90 Nm (55–66 lb-ft).

Install the trailing arm–to–rear axle bolts (2).
Tighten
Tighten the trailing arm–to–rear axle bolts to 80–90
Nm (59–66 lb-ft).
2. Install the rear shock absorber. Refer to “Shock Ab-
sorber” in this section.
D106C516
D106C517
REAR AXLE ASSEMBLY
(INCLUDING COIL SPRING)
Removal Procedure
1. Remove the rear brake drum, shoe and brake plate.
Refer to Section 4E, Rear Drum Brakes.
2. Remove the lateral rod. Refer to “Lateral Rod” in this
section.
3. Disconnect the rear axle and the trailing arm.

Support the rear axle with adjustable jack stands
(1).

Remove the shock absorber–to–rear axle bolt (2).

Loosen the shock absorber–to–body bracket nut
(3).

Remove the trailing arm–to–rear axle bolt (4).
Caution: When disconnecting the rear axle and the
trailing arm, coil spring tension may cause the ad-
justable jack stand to slip from the rear axle. This
may result in personal injury. Carry out the opera-
tion with co–worker.
D106C518
4. Remove the rear axle from the vehicle.

Remove the coil spring by lowering the jack stand
slowly (1).

Lower the support jack and remove the rear axle
(2).

2D –12 REAR SUSPENSION
DAEWOO M-150 BL2
UNIT REPAIR
D106C701
HUB AND BEARING ASSEMBLY
Tools Required
DW 340–010 Front Wheel Hub Remover
DW 350–030 Rear Wheel Bearing Race Installer
Disassembly Procedure
1. Remove the rear brake drum. Refer to Section 4E,
Rear Drum Brakes.
2. Remove the rear wheel bearing.

Remove the outer tapered roller bearing (1).
D106C702

Remove the oil seal (2).

Remove the inner tapered roller bearing (3).
D106C703
3. Remove the bearing races from the brake drum.

Remove the inner bearing race (1).

2D –14 REAR SUSPENSION
DAEWOO M-150 BL2
D106C708

Install the outer bearing (3).
3. Install the brake drum. Refer to Section 4E, Rear
Drum Brakes.
4. Adjust the end play and free load of the bearing. Re-
fer to “Check and Adjustments” in this section.

REAR SUSPENSION 2D–15
DAEWOO M-150 BL2
SPECIFICATIONS
GENERAL SPECIFICATIONS
Application Unit Description
Suspension Type– Isolated Trailing Link
Maximum Lengthmm (in.) 394.5 ± 3 (15.53 ± 0.12)
Shock Absorber Minimum Lengthmm (in.) 257.5 ± 3 (10.14 ± 0.12)

Shock Absorber
Strokemm (in.) 137 (5.39)
Clearancemm (in.) 0
Rear Wheel Bearing No LoadNm (lb-in.) 0.137 – 0.422 (0.9 – 3.7)
Coil Spring Height (No Load)mm (in.) 291 (11.46)
Grease Type (Rear Wheel Bearing and Hub)–M–8143 ANTIF BRG GREASE
FASTENER TIGHTENING SPECIFICATIONS
Application Nm Lb-Ft Lb-In Shock Absorber–to–Body Bracket Nut 45 – 70 33 – 52 – Shock Absorber–to–Rear Axle Bolt 45 – 70 33 – 52 – Trailing Arm–to–Rear Axle Bolt 80 – 90 59 – 66 – Trailing Arm–to–Body Bracket Bolt 70 – 90 55 – 66 – Lateral Rod–to–Body Bracket Bolt 50 – 70 37 – 52 – Lateral Rod–to–Rear Axle Nut 35 – 55 25 – 41 – Rear Axle Castellated Nut* – – – ABS Rear Speed Sensor Retaining Bolt 9 – 13 – 80 – 11 5

Rear Axle Castellated Nut : Refer to Section 4E, Rear Drum Brakes