automatic transaxle DAEWOO NUBIRA 2004 Service Repair Manual

AISIN AUTOMATIC TRANSAXLE 5A2 – 145
DAEWOO V–121 BL4
36. Using 1st & reverse brake adapter DW240–070 and
brake spring compressor bolt/nut DW240–060–01,
install the snap ring.
Notice : Make sure that the snap ring is installed in the
groove of the transaxle case correctly.
37. Using a dial indicator, measure the 1st & reverse
brake piston stroke while applying and releasing
392–785 kPa (57–114 psi) of compressed air.
Notice : If the piston stroke is non–standard, inspect the
discs, plates and flange. Piston stroke 0.6
1.3 mm (0.024

0.051 in.)
38. Using counter drive gear installation adapter
DW240–100, brake spring compressor bolt/nut
DW240–060–01 and brake spring compressor plate
DW240–060–02, install the counter drive gear.
Notice : Be careful not to apply excessive force to the
transaxle case.
39. Coat a new oil seal with ATF.
40. Install the oil seal to the transaxle case.
S Oil seal in depth:
A: 1 ± 0.25 mm (0.39 ± 0.0098 in.)

5A2 – 146IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
41. Install the parking lock rod to the manual valve le-
ver.
42. Install a new spacer to the manual valve lever.
43. Install the manual valve lever shaft and manual
valve lever.
44. Using a pin punch and hammer, drive in a new pin.

AISIN AUTOMATIC TRANSAXLE 5A2 – 147
DAEWOO V–121 BL4
45. Turn the spacer and lever shaft to align the small
hole for locating the staking position in the spacer
with the staking position mark on the lever shaft.
46. Using a pin punch, stake the spacer through the
small hole.
47. Check that the spacer does not turn.
48. Install the manual detent spring with the bolt.
Tighten
Tighten the bolts to 9.8 NSm (87 lb–in).
49. Install the parking lock shaft, torsion spring and
parking lock pawl.
Notice : Check that the edge of torsion spring fits into the
groove securely.

5A2 – 148IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
50. Install the parking lock pawl bracket with the 2
bolts.
Tighten
Tighten the bolts to 7.4 NSm (65 lb–in).
51. Using counter drive gear installation adapter
DW240–100 and brake spring compressor bolt/nut
DW240–060–01,install the planetary ring gear.
S Before installing the planetary ring gear, be sure
to replace the planetary ring flange of the plane-
tary ring gear with a new one.
52. Fix the counter drive gear with parking lock pawl.
53. Using planetary ring gear nut removal/installation
socket DW260–041, install a new nut.
Tighten
Tighten the nut to 9.8 NSm (87 lb–in).

AISIN AUTOMATIC TRANSAXLE 5A2 – 149
DAEWOO V–121 BL4
54. Using a small torque wrench, while turning to count-
er drive gear 100 turn per minute and measure the
preload.
Notice : When the preload is smaller than the specifica-
tion, tighten the nut more and adjust the preload. Preload:
0.05–0.35 NSm (0.43–3.12 lb–in)
Tighten
Tighten the nut to 29 NSm (22 lb–ft) or less.
55. Stake the nut.
56. Install the planetary gear to the transaxle case.
57. Coat the planetary carrier thrust washer with petro-
leum jelly and install it onto the planetary gear.
58. Install the No.2 one–way clutch to the transaxle
case.

5A2 – 150IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
59. Check that the planetary gear turns freely counter-
clockwise and locks clockwise.
60. Install the anti–rattle clip in the place shown in the
illustration (the space between the No.2 one–way
clutch outer race and transaxle case), push the
anti–rattle clip in until you hear the ”click”.
61. Using vernier calipers, measure the free length of
the 2nd brake piston return spring together with
spring seat.
S Standard free length: 15.85 mm (0.6240 in.).
62. Check to see if the sliding surface of the disc, plate
and flange of 2nd brake are worn or burnt. If neces-
sary, replace them.
Notice : If the lining of the disc is peeling off or discolored,
or even if a part of the groove is defaced, replace all discs.
Notice : Before assembling new discs, soak them in ATF
for at least 15 minutes.

AISIN AUTOMATIC TRANSAXLE 5A2 – 151
DAEWOO V–121 BL4
63. Install the flange, 2 discs and 2 plates.
S Install in order : F
D
P
D
P
(D = Disc, P = Plate, F = Flange)
64. Install the 2nd brake return spring.
Notice : Make sure that the snap ring is installed in the
groove of the transaxle case correctly.
65. Coat 2 new O–rings with ATF, install them to the
2nd brake piston.
66. Install the 2nd brake piston into the 2nd brake
clutch cylinder.
Notice : Be careful not to damage the O–rings.
67. Install the 2nd brake clutch cylinder to the transaxle
case.

5A2 – 152IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
68. Using brake spring compressor bolt / nut
DW240–060–01 and 2nd brake adapter
DW240–080, compress the 2nd brake piston return
spring.
69. Using a screwdriver, install the snap ring.
Notice : Make sure that the snap ring is installed in the
groove of the transaxle case correctly.
70. Coat the thrust bearing race with petroleum jelly
and install it onto the front planetary sun gear.
S Race:
Inner diameter: 19.3 mm (0.760 in.)
Outer diameter : 29.0 mm (1.142 in.)
71. Install the front planetary sun gear to the transaxle
case.
72. Install the thrust washer and one–way clutch as-
sembly to the rear planetary sun gear.

AISIN AUTOMATIC TRANSAXLE 5A2 – 153
DAEWOO V–121 BL4
73. Coat the thrust bearing race with petroleum jelly
and install it onto the rear planetary sun gear and
one–way clutch assembly.
S Bearig:
Inner diameter: 42.5 mm (1.673 in.)
Outer diameter: 57.5 mm (2.264 in.)
Notice : Check the direction of the bearing.
74. Install the rear planetary sun gear and one–way
clutch assembly to the transaxle case.
75. Coat the thrust bearing race with petroleum jelly
and install it onto the transaxle case.
S Race:
Inner diameter: 34.95 mm (1.3760 in.)
Outer diameter: 45.50 mm (1.7913 in.)
Notice : Check the direction of race.
76. Coat the thrust needle roller bearing with petroleum
jelly and install it onto the forward clutch hub.
S Bearig:
Inner diameter: 33.3 mm (1.311 in.)
Outer diameter: 46.5 mm (1.831 in.)
Notice : Check the direction of bearing.

5A2 – 154IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
77. Install the forward clutch hub to the transaxle case.
78. Coat the thrust bearing race with petroleum jelly
and install it onto the forward clutch hub.
S Race:
Inner diameter: 19.3 mm (1.760 in.)
Outer diameter: 30.6 mm (1.205 in.)
79. Install the thrust bearing race and thrust needle roll-
er bearing to the forward & reverse clutch assem-
bly.
S Race and bearing diameter: mm(in.)
Inner diameterOuter diameter
Race18.1 (0.713)28.2 (1.110)
Bearing18.1 (0.713)29.6 (1.165)
80. Install the forward & reverse clutch assembly to the
transaxle case.