check engine DAEWOO NUBIRA 2004 Service Service Manual

ENGINE COOLING 1D – 9
DAEWOO V–121 BL4
THERMOSTAT (1.4L/1.6L DOHC)
Removal Procedure
CAUTION : To prevent personal injury, do not remove
the surge tank cap while the engine and the radiator
are hot because the heat causes the system to remain
under pressure. Scalding fluid and steam may be
blown out under pressure.
1. Drain the coolant. Refer to ”Draining and Refilling
the Cooling System” in this section.
2. Loosen the hose clamp on the upper radiator hose
at the thermostat housing.
3. Disconnect the upper radiator hose from the ther-
mostat housing.
4. Loosen the clamp on the bypass hose.
5. Disconnect the bypass hose from the thermostat
housing.
6. Remove the mounting bolts that hold the thermo-
stat housing to the cylinder head.
7. Remove the thermostat housing from the head.
8. Remove the O–ring seal from the head.
9. Check the valve seat for foreign matter that could
prevent the valve from seating properly.
10. Check the thermostat for proper operation. Refer to
”Thermostat Test” in this section.
11. Clean the thermostat housing and the cylinder head
mating surfaces.
Installation Procedure
1. Coat the sealing surface of a new O–ring seal with
Lubriplater®.
2. Install a new O–ring seal into the recess in the cyl-
inder head.
3. Secure the thermostat housing to the cylinder head
with the mounting bolts.
Tighten
Tighten the thermostat housing mounting bolts to 20
NSm (15 lb–ft).

SECTION : 1E
ENGINE ELECTRICAL
CAUTION : Disconnect the negative battery cable before removing or installing any electrical unit or when a tool
or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable will help
prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise noted.
TABLE OF CONTENTS
SPECIFICATIONS1E–2 . . . . . . . . . . . . . . . . . . . . . . . . . .
Starter Specifications 1E–2. . . . . . . . . . . . . . . . . . . . . .
Battery Specifications 1E–2. . . . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications 1E–3. . . . . . . . . .
SCHEMATIC AND ROUTING DIAGRAMS1E–4 . . . . .
Startimg System 1E–4. . . . . . . . . . . . . . . . . . . . . . . . . .
Charging System 1E–5. . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS1E–6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
No Crank 1E–6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starter Motor Noise 1E–9. . . . . . . . . . . . . . . . . . . . . . .
Battery Load Test 1E–9. . . . . . . . . . . . . . . . . . . . . . . . .
Genrator Output Test 1E–10. . . . . . . . . . . . . . . . . . . . .
Generator System Check 1E–10. . . . . . . . . . . . . . . . .
MAINTENANCE AND REPAIR1E–11 . . . . . . . . . . . . . .
ON–VEHICLE SERVICE 1E–11. . . . . . . . . . . . . . . . . . . .
Generator 1E–11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starter 1E–14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery and Battery Tray 1E–15. . . . . . . . . . . . . . . . . . . UNIT REPAIR 1E–17. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starter Motor 1E–17. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Generator 1E–25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION AND SYSTEM
OPERATION1E–30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery 1E–30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ratings 1E–30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reserve Capacity 1E–30. . . . . . . . . . . . . . . . . . . . . . . . .
Cold Cranking Amperage 1E–30. . . . . . . . . . . . . . . . . .
Built–In Hydrometer 1E–30. . . . . . . . . . . . . . . . . . . . . . .
Charging Procedure 1E–30. . . . . . . . . . . . . . . . . . . . . . .
Charging Time Required 1E–31. . . . . . . . . . . . . . . . . . .
Charging a Completely Discharged Battery
(OFF the Vehicle) 1E–31. . . . . . . . . . . . . . . . . . . . . . .
Jump Starting Procedure 1E–31. . . . . . . . . . . . . . . . . .
Generator 1E–32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Charging System 1E–32. . . . . . . . . . . . . . . . . . . . . . . . .
Starter 1E–32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting System 1E–32. . . . . . . . . . . . . . . . . . . . . . . . . .

1E – 6IENGINE ELECTRICAL
DAEWOO V–121 BL4
DIAGNOSIS
NO CRANK
StepActionValue(s)YesNo
11. Turn the headlamps ON.
2. Turn the dome lamps ON.
3. Turn the ignition to START.
Did the lights dim or go out?–Go to Step 2Go to Step 8
2Check the battery state of charge.
Is the green eye showing from the built–in hydrome-
ter?–Go to Step 3Go to
”Charging Pro-
cedure”
31. Connect the voltmeter positive lead to the posi-
tive battery terminal.
2. Connect the voltmeter negative lead to the
negative battery terminal.
3. Turn the ignition to START.
Does the voltmeter indicate the value specified?< 9.6 vGo to
”Charging Pro-
cedure”Go to Step 4
41. Connect the voltmeter negative lead to the
negative battery terminal.
2. Connect the positive voltmeter lead to the en-
gine block.
Does the voltmeter indicate the value specified?> 0.5 vGo to Step 5Go to Step 6
5Clean, tighten, or replace the negative battery cable.
Is the repair complete?–System OK–
61. Connect the voltmeter positive lead to the start-
er ”B+” terminal.
2. Connect the voltmeter negative lead to the
negative battery terminal.
Does the voltmeter indicate the value specified?< 9 vGo to Step 7Go to Step 13
7Clean, tighten, or replace the positive battery cable.
Is the repair complete?–System OK–
8Inspect the engine fuse block fuse Ef5.
Is the fuse OK?–Go to Step 10Go to Step 9
9Inspect the engine fuse block fuse Ef4.
Is the fuse OK?–System OK–
10Check the connection at the starter ”ST” terminal.
Is the connection OK?–Go to Step 12Go to Step 11
11Clean or tighten the connection as needed.
Is the repair complete?–System OK–
121. Connect the voltmeter positive lead to the start-
er ”ST” terminal.
2. Connect the voltmeter negative lead to the
negative battery terminal.
3. Turn the ignition to START.
Does the voltmeter indicate the value specified?< 7 vGo to Step 13Go to Step 14
13Repair or replace the starter as needed.
Is the repair complete?–System OK–
14Determine the type of transaxle on the vehicle.
Is the vehicle equipped with an automatic transaxle?–Go to Step 15Go to Step 32

ENGINE ELECTRICAL 1E – 9
DAEWOO V–121 BL4
STARTER MOTOR NOISE
To correct starter motor noise during starting, use the following procedure:
Checks
Action
Check for a high–pitched whine during cranking, before
the engine fires. The engine cranks and fires properly.The distance is too great between the starter pinion and
the flywheel. Shimming the starter toward the flywheel is
required.
Check for a high–pitched whine after the engine fires, as
the key is being released. The engine cranks and fires
properly. This intermittent complaint is often diagnosed as
”starter hang–in” or ”solenoid weak.”The distance is too small between the starter pinion and
the flywheel. Shimming the starter away from the flywheel
is required.
Check for a loud ”whoop” after the engine fires but while
the starter is still held engaged. The sound is like a siren
if the engine is revved while the starter is engaged.The most probable cause is a defective clutch. A new
clutch will often correct this problem.
Check for a ”rumble,” a ”growl,” or, in severe cases, a
”knock” as the starter is coasting down to a stop after start-
ing the engine.The most probable cause is a bent or unbalanced starter
armature. A new armature will often correct this problem.
If the complaint is noise, correction can be achieved by
proper shimming as follows:
1. Check for a bent or a worn flywheel.
2. Start the engine and carefully touch the outside di-
ameter of the rotating flywheel ring gear with chalk
or a crayon to show the high point of the tooth run-
out. Turn the engine OFF and rotate the flywheel so
that the marked teeth are in the area of the starter
pinion gear.
3. Disconnect the negative battery cable to prevent
cranking the engine.
4. Check the pinion–to–flywheel clearance by using a
wire gauge of 0.5 mm (0.02 inch) minimum thick-
ness (or diameter). Center a pinion tooth between
two flywheel teeth and the gauge. Do not gauge in
the corners, where a misleading larger dimension
may be observed. If the clearance is under this
minimum, shimming the starter away from the fly-
wheel is required.
5. If the clearance approaches 1.5 mm (0.06 inch) or
more, shimming the starter toward the flywheel is
required. This condition is generally the cause of
broken flywheel teeth or the starter housing. Shim
the starter toward the flywheel by shimming only
the outboard starter mounting pad. A shim of 0.40
mm (0.016 inch) thickness at this location will de-
crease the clearance by approximately 0.30 mm
(0.012 inch). If normal starter shims are not avail-
able, plain washers or other suitable material may
be used as shims.BATTERY LOAD TEST
1. Check the battery for obvious damage, such as a
cracked or broken case or cover, which could per-
mit the loss of electrolyte. If obvious damage is
noted, replace the battery.
CAUTION : Do not charge the battery if the hydrome-
ter is clear or light yellow. Instead, replace the battery.
If the battery feels hot, or if violent gassing or spew-
ing of electrolyte through the vent hole occurs, dis-
continue charging or reduce the charging rate to
avoid personal injury.
2. Check the hydrometer. If the green dot is visible, go
to the load test procedure. If the indicator is dark
but green is not visible, charge the battery. For
charging a battery removed from the vehicle, refer
to ”Charging a Completely Discharged Battery” in
this section.
3. Connect a voltmeter and a battery load tester
across the battery terminals.
4. Apply a 300–ampere load for 15 seconds to remove
any surface charge from the battery.
5. Remove the load.
6. Wait 15 seconds to let the battery recover, and ap-
ply a 270–ampere load.
Important : The battery temperature must be estimated
by touch and by the temperature condition the battery has
been exposed for the preceding few hours.
7. If the voltage does not drop below the minimum
listed, the battery is good and should be reinstalled.
If the voltage is less than the minimum listed, re-
place the battery. Refer to ”Battery Specifications”
in this section.

1E – 10IENGINE ELECTRICAL
DAEWOO V–121 BL4
GENRATOR OUTPUT TEST
1. Perform the generator system test. Refer to ”Gen-
erator System Check”in this section.
2. Replace the generator if it fails that test. Refer to
”Generator” in the On–Vehicle Service portion of
this section. If it passes the test, perform the on–
vehicle output check which follows.
Important : Always check the generator for output before
assuming that a grounded ”L” terminal circuit has dam-
aged the regulator.
3. Attach a digital multimeter, an ammeter, and a car-
bon pile load to the vehicle.
Important : Be sure the vehicle battery is fully charged,
and the carbon pile load is turned off.
4. With the ignition switch in the OFF position, check
and record the battery voltage.
5. Remove the harness connector from the generator.
6. Turn the ignition to RUN with the engine not run-
ning. Use a digital multimeter to check for voltage in
the harness connector ”L” terminal.
7. The reading should be near the specified battery
voltage of 12 volts. If the voltage is too low, check
the indicator
L" terminal circuits for open and
grounded circuits causing voltage loss. Correct any
open wires, terminal connections, etc., as neces-
sary. Refer to”Charging System” in this section.
8. Attach the generator harness connector.
9. Run the engine at a moderate idle, and measure
the voltage across the battery terminals. The read-
ing should be above that recorded in step 14, but
less than 16 volts. If the reading is over 16 volts or
below the previous reading, replace the generator.
Refer to”Generator” in the On–Vehicle Service sec-
tion.
10. Run the engine at a moderate idle, and measure
the generator amperage output.
11. Turn on the carbon pile, and adjust it to obtain the
maximum amps while maintaining the battery volt-
age above 13 volts.
12. If the reading is within 15 amps of the generator’s
rating noted on the generator, the generator is
good. If not, replace the generator. Refer to”Gener-
ator” in the On–Vehicle Service section.
13. With the generator operating at the maximum out-
put, measure the voltage between the generator
housing and the battery negative terminal. The volt-
age drop should be 0.5 volt or less. If the voltage
drop is more than 0.5 volt, check the ground path
from the generator housing to the negative battery
cable.
14. Check, clean, tighten, and recheck all of the ground
connections.
GENERATOR SYSTEM CHECK
When operating normally, the generator indicator lamp will
come on when the ignition is in RUN position and go out
when the engine starts. If the lamp operates abnormally
or if an undercharged or overcharged battery condition oc-
curs, the following procedure may be used to diagnose the
charging system. Remember that an undercharged bat-
tery is often caused by accessories being left on overnight
or by a defective switch that allows a lamp, such as a trunk
or a glove box lamp, to stay on.
Diagnose the generator with the following procedure:
1. Visually check the belt and the wiring.
2. With the ignition in the ON position and the engine
stopped, the charge indicator lamp should be on. If
not, detach the harness at the generator and
ground the ”L” terminal in the harness with a 5–am-
pere jumper lead.
S If the lamp lights, replace the generator. Refer to
”Generator” in the On–Vehicle Service section.
S If the lamp does not light, locate the open circuit
between the ignition switch and the harness
connector. The indicator lamp bulb may be
burned out.
3. With the ignition switch in the ON position and the
engine running at moderate speed, the charge indi-
cator lamp should be off. If not, detach the wiring
harness at the generator.
S If the lamp goes off, replace the generator. Re-
fer to ”Generator” in the On–Vehicle Service
section.
S If the lamp stays on, check for a short to ground
in the harness between the connector and the
indicator lamp.
Important : Always check the generator for output before
assuming that a grounded ”L” terminal circuit has dam-
aged the regulator. Refer to”Generator” in the Unit Repair
section.

ENGINE ELECTRICAL 1E – 15
DAEWOO V–121 BL4
4. Position the starter electrical wire on the solenoid
terminals and the ground wire on the lower stud.
5. Install the starter solenoid nuts and the ground wire
nut.
Tighten
Tighten the starter solenoid terminal–to–battery cable
terminal nut to 5.5 NSm (49 lb–in), and the starter sole-
noid terminal–to–ignition solenoid terminal nut to 5.5
NSm (49 lb–in).
Tighten the starter lower mounting stud ground wire
nut to 12 NSm (106 lb–in).
BATTERY AND BATTERY TRAY
Removal Procedure
1. Disconnect the negative battery cable and then dis-
connect the positive battery cable.
2. Remove the nuts from the battery rods that fasten
the battery hold–down bar clamp.
3. Check the battery carrier tray for obvious cracks or
damage. Unclip the lead to the negative battery
cable from the side of the battery tray (if applica-
ble). Detach the carrier tray if necessary by remov-
ing the upper battery carrier tray bolts, and the side
bolt that connects the hydraulic clutch hose bracket
to the battery carrier tray (if applicable).
4. Remove the lower battery tray bolts.
Installation Procedure
1. Install the battery carrier by fastening the carrier
tray upper, lower, and side bolts.
Tighten
Tighten the battery carrier tray upper, lower and side
bolts (if applicable) to 20 NSm (15 lb–ft).
2. Push in the clip of the negative battery lead to the
hole in the side of the battery tray (if applicable and
as shown).

ENGINE ELECTRICAL 1E – 17
DAEWOO V–121 BL4
UNIT REPAIR
STARTER MOTOR
Disassembly Procedure
1. Remove the starter. Refer to ”Starter” in this sec-
tion.
2. Remove the starter through–bolts.
3. Remove the commutator end frame and brush
holder assembly.
4. Inspect the brushes, the pop–out springs, and the
brush holders for wear and damage. Replace the
assembly, if needed.
5. Check the armature to see if it turns freely. If the
armature does not turn freely, break down the as-
sembly immediately, starting with Step 14. Other-
wise, give the armature a no–load test.
Notice : Complete the testing in a minimum amount of
time to prevent overheating and damaging the solenoid.
Important : If the specified current draw does not include
the solenoid, deduct from the armature reading the speci-
fied current draw of the solenoid hold–in winding.
6. To begin the no–load test, close the switch and
compare the rpm, the current, and the voltage read-
ings with the specifications. Refer to ”Starter Speci-
fications” in this section. Make disconnections only
with the switch open. Use the test results as fol-
lows:

ENGINE ELECTRICAL 1E – 19
DAEWOO V–121 BL4
9. Remove the plunger return spring.
Important : If the solenoid is not removed from the starting
motor, the connector strap terminals must be removed
from the terminal on the solenoid before making these
tests.
10. Test the solenoid windings by checking the current
draw.
1) Check the hold–in windings by connecting an
ammeter in series with a 12–volt battery, the
switch terminal, and to ground.
2) Connect the carbon pile across the battery.
3) Adjust the voltage to 10 volts. The ammeter
reading should be 13 to 19 amperes.Current will
decrease as the windings heat up. Current draw
readings that are over specifications indicate
shorted turns or a ground in the windings of the
solenoid. Both conditions require replacement of
the solenoid. Current draw readings that are un-
der specifications indicate excessive resistance.
No reading indicates an open circuit.
Important : Current will decrease as the windings heat up.
Current draw readings that are over specifications indicate
shorted turns or a ground in the windings of the solenoid.
Both conditions require replacement of the solenoid. Cur-
rent draw readings that are under specifications indicate
excessive resistance. No reading indicates an open cir-
cuit.
11. Check both windings, connecting them according to
the preceding test.
1) Ground the solenoid motor terminal.
2) Adjust the voltage to 10 volts. The ammeter
reading should be 59 to 79 amperes.
3) Check the connections and replace the sole-
noid, if necessary.

1E – 20IENGINE ELECTRICAL
DAEWOO V–121 BL4
12. Slide the field frame with enclosed armature as-
sembly away from the starter assembly.
13. Remove the shield.
14. Separate the field frame from the armature.
15. Inspect the shaft and the pinion for discoloration,
damage, or wear. Replace, if necessary.
16. Inspect the armature commutator. If the commuta-
tor is rough, it should be turned down. The outside
diameter of the commutator must measure at least
26.9 – 27.1mm (1.059 – 1.067 in.) after it is under-
cut or turned. Do not turn out–of–round commuta-
tors.
17. Inspect the points where the armature conductors
join the commutator bars. Make sure they have a
good connection. A burned commutator bar is usu-
ally evidence of a poor connection.
18. If test equipment is available, check the armature
for short circuits by placing it on a growler, and
holding back a saw blade over the armature core
while the armature is rotated. If the saw blade vi-
brates, replace the armature.
19. Recheck the armature after cleaning between the
commutator bars. If the saw blade vibrates, replace
the armature.

1E – 22IENGINE ELECTRICAL
DAEWOO V–121 BL4
24. Remove the plunger with the boot and the shift le-
ver assembly. Test the solenoid windings, if not
done in Step 11.
Important : The pinion clearance must be correct to pre-
vent the buttons on the shift lever yoke from rubbing on the
clutch collar during the cranking.
25. When the starter motor is disassembled and the
solenoid is replaced, it is necessary to check the
pinion clearance.
26. Disconnect the motor field coil connector from the
solenoid motor terminal and carefully insulate the
connector.
27. Connect one 12–volt battery lead to the solenoid
switch terminal and the other to the starter frame.
28. Flash a jumper lead momentarily from the solenoid
motor terminal to the starter frame, allowing shifting
of the pinion in the cranking position, where it will
remain until the battery is disconnected.
Important : A means for adjusting the pinion clearance is
not provided on the starter motor. If the clearance does not
fall within the limits, check for improper installation and re-
place all worn parts.
29. Push the pinion back as far as possible to take up
any movement, and check the clearance with a
feeler gauge. The clearance should be 0.25 to 3.56
mm (0.01 to 0.14 inch).
Assembly Procedure
1. Install the drive and the pinion stop on the drive-
shaft.