immobilizer DODGE NEON 2000 Service Owner's Manual

8W-40 INSTRUMENT CLUSTER
Component Page
A/C Heater Control..................8W-40-10
Airbag Control Module................8W-40-6
Brake Warning Indicator..............8W-40-11
Brake Warning Indicator Switch........8W-40-5
Center Stack Lamp..................8W-40-10
Circuit Breaker No. 2 (FB)............8W-40-12
Combination Flasher................8W-40-3, 4
Controller Anti-Lock Brake.............8W-40-5
Data Link Connector.................8W-40-5
Dome Lamp........................8W-40-9
Dome Lamp/Intrusion Sensor...........8W-40-9
Driver Door Ajar Switch.............8W-40-7, 8
Engine Coolant Temperature Sensor.....8W-40-5
Engine Oil Pressure Switch............8W-40-5
Front Fog Lamp Switch..............8W-40-14
Fuel Pump Module...................8W-40-6
Fuse 1 (FB).......................8W-40-3, 4
Fuse 10 (FB)........................8W-40-2
Fuse 11 (FB)........................8W-40-2
Fuse 13 (PDC)......................8W-40-2
Fuse 15 (FB)........................8W-40-2
Fuse 15 (PDC).....................8W-40-3, 4
Fuse 19 (FB).......................8W-40-13
Fuse 20 (FB).......................8W-40-14
Fuse Block................8W-40-2, 3, 4, 12, 13
G101..............................8W-40-5
G204............................8W-40-2, 9
G301.............................8W-40-11
Headlamp Beam Select...............8W-40-12
Headlamp Leveling Switch............8W-40-10
Headlamp Switch...............8W-40-2, 12, 14Component Page
High Beam Indicator.................8W-40-11
Ignition Switch....................8W-40-7, 8
Indicator Drivers....................8W-40-11
Instrument Cluster.......8W-40-2, 3, 4, 6, 7, 8, 9,
10, 11, 12, 13, 14
Instrument Panel Drivers......8W-40-6, 7, 8, 9, 14
Left Front Fog Lamp................8W-40-13
Left Front Turn Signal Lamp...........8W-40-3
Left Park/Turn Signal Lamp..........8W-40-3, 4
Left Rear Door Ajar Switch...........8W-40-7, 8
Map/Reading Lamps..................8W-40-9
Multi-Function Switch..........8W-40-2, 3, 4, 9,
11, 12, 13, 14
Park Brake Switch..................8W-40-11
Passenger Door Ajar Switch..........8W-40-7, 8
Power Distribution Center.......8W-40-2, 3, 4, 14
Powertrain Control Module............8W-40-5
PRNDL Lamp......................8W-40-10
Radio.............................8W-40-10
Rear Window Defogger Switch.........8W-40-10
Remote Keyless Entry Module........8W-40-6, 8
Right Front Fog Lamp...............8W-40-13
Right Front Turn Signal Lamp..........8W-40-3
Right Park/Turn Signal Lamp.........8W-40-3, 4
Right Rear Door Ajar Switch..........8W-40-7, 8
Seat Belt Indicator..................8W-40-11
Seat Belt Switch....................8W-40-11
Sentry Key Immobilizer Module.........8W-40-6
Traction Control Switch..............8W-40-10
Vehicle Speed Sensor.................8W-40-5
PL8W - 40 INSTRUMENT CLUSTER 8W - 40 - 1

INSTRUMENT
CLUSTER
A (8W-40-5)
21
193
AIRBAG
CONTROL
MODULE
FUEL
PUMP
MODULE
MODULE ENTRY
KEYLESS
REMOTEFROM
C104
A12C30512G4
18
DB
G4
18
DB
D25
18
VT/YLD25
20
VT/YLD25
22
VT/YL
D25
22
VT/YL
S217
FUEL
LEVEL
SENSOR
SIGNALPCI
BUS
BUSPCI
BUSPCI
VT/YL22 D25
2
MODULE IMMOBILIZER
KEY
SENTRY
2 7
INSTRUMENT
PANEL
DRIVERS
SPEEDOMETER FUEL
GAUGE
INDICATOR PRESSURE
OIL
LOW BRAKE
WARNING
INDICATOR TRACTION
OFF
INDICATOR AIRBAG
WARNING
INDICATORLOW
FUEL
INDICATOR ABS
INDICATOR CHECK
ENGINE
INDICATOR
GAUGE TEMPERATURE
COOLANT
ENGINE TACHOMETER
ODOMETER/TRIP
INDICATOR AJAR
DOOR TRACTION
CONTROL
OFF
INDICATOR INDICATOR
ENGAGED
CRUISE(8W-43-2)
(8W-30-10)
(8W-39-10)
(8W-39-11) (8W-39-3)
(8W-30-4)
8W - 40 - 6 8W-40 INSTRUMENT CLUSTERPL
008W-10PLI04006

Component Page
PRNDL Lamp......................8W-80-39
Proportional Evap/Purge Solenoid.......8W-80-39
Radiator Fan Motor.................8W-80-39
Radio.............................8W-80-39
Rear Window Defogger Switch.........8W-80-40
Remote Keyless Entry Module.........8W-80-40
Right Back-Up Lamp................8W-80-41
Right City Lamp....................8W-80-41
Right Front Door Speaker.............8W-80-41
Right Front Fog Lamp...............8W-80-41
Right Front Side Marker Lamp........8W-80-42
Right Front Turn Signal Lamp.........8W-80-42
Right Front Wheel Speed Sensor.......8W-80-42
Right Headlamp....................8W-80-42
Right Headlamp Leveling Motor........8W-80-43
Right Instrument Panel Speaker.......8W-80-43
Right License Lamp.................8W-80-43
Right Park/Turn Signal Lamp..........8W-80-43
Right Rear Door Lock Motor...........8W-80-43
Right Rear Fog Lamp................8W-80-44
Right Rear Speaker..................8W-80-44
Right Rear Turn Signal Lamp..........8W-80-44Component Page
Right Rear Wheel Speed Sensor........8W-80-44
Right Repeater Lamp................8W-80-44
Right Tail/Stop Lamp................8W-80-45
Right Tail/Stop/Turn Signal Lamp......8W-80-45
Seat Belt Switch....................8W-80-45
Sentry Key Immobilizer Module........8W-80-45
Siren.............................8W-80-45
Sunroof Control Module..............8W-80-46
Sunroof Motor......................8W-80-46
Sunroof Switch.....................8W-80-46
Sunroof Vent Switch.................8W-80-46
Throttle Position Sensor..............8W-80-46
Torque Converter Clutch Solenoid.......8W-80-47
Traction Control Switch..............8W-80-47
Trunk Key Cylinder Switch............8W-80-47
Underhood Lamp...................8W-80-47
Vehicle Speed Control Servo...........8W-80-47
Vehicle Speed Sensor................8W-80-48
Windshield Washer Pump.............8W-80-48
Wipe/Wash Switch...................8W-80-48
Wiper Motor.......................8W-80-48
PL8W - 80 CONNECTOR PIN-OUTS 8W - 80 - 3

CAV CIRCUIT FUNCTION
1
Z1 18BK GROUND
2
L7 18BK/YL HEADLAMP SWITCH OUTPUT
3 L62 18BR/RD RIGHT TURN SIGNAL
RIGHT TAIL/STOP/
TURN SIGNAL LAMP
SEAT BELT SWITCH
1 2
BLACK
SEAT BELT SWITCH SENSE 20LG/RD G10 1
GROUND 18BK Z1 2
FUNCTION CIRCUIT CAV
(EXCEPT BUILT-UP-EXPORT)
M1 20PKFUSED B(+) GROUND
Z1 18BK X5 20WT/RDDISPLAY BACKLIGHT
4
1
SIREN
DISPLAY BACKLIGHT
X5 20WT/RDFUNCTION
CAV CIRCUIT
1
2
4 3
MODULE IMMOBILIZER
- -- -
FUSED B(+)
M1 20PKGROUND
Z2 20BK/LGFUSED IGNITION SWITCH OUTPUT (ST-RUN)
G5 20DB/WTPCI BUS D25 22VT/YL1
6
SENTRY KEY
FUNCTION
CAV CIRCUIT
1
2
4 3
6 5
RIGHT TAIL/STOP
LAMP
(BUILT-UP-EXPORT)
1 3
HEADLAMP SWITCH OUTPUTGROUND Z1 18BK
3
CAV CIRCUIT FUNCTION
1
L50 18WT/TN BRAKE LAMP SWITCH OUTPUT 2 L7 18BK/YL
(BUILT-UP-EXPORT)
31
BLACK
BLACK
BLACK
PL8W-80 CONNECTOR PIN-OUTS 8W - 80 - 45
PLI08045008W-10

Connector
Name/NumberColor Location Fig.
Proportional
EVAP/Purge
SolenoidBK Left Rear of
Engine
Compartment2
Radiator Fan
MotorBK Front of
Engine
Compartment2
Radio - C1 BK Rear of Radio 7
Radio - C2 GY Rear of Radio 7
Rear Window
Defogger
SwitchBK Center of
Instrument
Panel7
Remote
Keyless Entry
ModuleBK Center of
Instrument
Panel7
Right Back-Up
LampBK At Lamp 12
Right City
Lamp
(Built-Up-
Export)GY Right
Headlamp
OpeningN/S
Right Front
Door SpeakerBK At
Passengers
Door15
Right Front
Fog LampBK At Lamp N/S
Right Front
Side Marker
LampNAT At Lamp N/S
Right Front
Turn Signal
Lamp
(Built-Up-
Export)NAT At Lamp 3
Right Front
Wheel Speed
SensorBK At Right Front
Wheel
Opening1, 3
Right
HeadlampBK At Lamp 3
Right
Headlamp
Leveling Motor
(Built-Up-
Export)GY Rear of Right
HeadlampN/S
Right
Instrument
Panel SpeakerBK At Speaker 6, 7Connector
Name/NumberColor Location Fig.
Right License
Lamp
(Built-Up-
Export)NAT At Lamp 13
Right
Park/Turn
Signal Lamp
(Except
Built-Up-
Export)BK At Lamp N/S
Right Rear
Door Lock
MotorBK At Motor 16
Right Rear
Fog Lamp
(Built-Up-
Export)GY At Lamp 13
Right Rear
SpeakerBK At Speaker 11
Right Rear
Turn Signal
Lamp
(Built-Up-
Export)GY At Lamp 12
Right Rear
Wheel Speed
SensorBL At Right Rear
Wheel
OpeningN/S
Right
Repeater
Lamp
(Built-Up-
Export)BL At Lamp 1
Right Tail/Stop
Lamp
(Built-Up-
Export)BK At Lamp 12
Right
Tail/Stop/ Turn
Signal Lamp
(Except
Built-Up-
Export)BK At Lamp N/S
Seat Belt
SwitchBK Under Drivers
SeatN/S
Sentry Key
Immobilizer
ModuleBK Left Side of
Instrument
Panel6
Siren
(Built-Up-
Export)Left Front of
Vehicle1
PL8W - 90 CONNECTOR/GROUND LOCATIONS 8W - 90 - 5
DESCRIPTION AND OPERATION (Continued)

Connector
Name/NumberColor Location Fig.
Right Tail/Stop
LampBK At Lamp 31
Seat Belt
SwitchBK Under Drivers
SeatN/S
Sentry Key
Immobilizer
ModuleBK Right Side of
Instrument
Panel25
Siren Left Front of
Vehicle18
Sunroof
Control
ModuleAt Sunroof N/S
Sunroof Motor At Sunroof N/S
Sunroof
SwitchBK At Switch N/S
Sunroof Vent
SwitchAt Switch N/S
Throttle
Position
SensorBK On Throttle
Body19
Torque
Converter
Clutch
Solenoid
(ATX)BK On
Transmission19Connector
Name/NumberColor Location Fig.
Traction
Control SwitchWT Center of
Instrument
Panel24
Trunk Key
Cylinder
SwitchGY On Decklid 36
Underhood
LampBK At Lamp N/S
Vehicle Speed
Control ServoBK At Left Front
Strut Tower19
Vehicle Speed
SensorBK On
Transmission22
Windshield
Washer PumpRD At Right Front
Wheel
Opening18
Wipe/Wash
SwitchGY Center of
Instrument
Panel25
Wiper Motor BK Right Side of
Engine
Compartment23
PL8W - 90 CONNECTOR/GROUND LOCATIONS 8W - 90 - 25
DESCRIPTION AND OPERATION (Continued)

(20) Lower the steering column away from the
instrument panel.
(21) Disconnect the wiring harness electrical con-
nector from the clockspring (Fig. 13).
(22) Disconnect the wiring harness electrical con-
nectors from the multi-function switch, windshield
wiper switch, and ignition switch (Fig. 14).(23) If the vehicle is equipped with a Sentry Key
Immobilizer Module (SKIM), disconnect its electrical
connector (Fig. 15).
(24) Remove the steering column from the vehicle.
(25) If the steering column is being replaced, per-
form the following:
(a) Remove the ignition key cylinder from the
steering column. To do this, insert the key and
turn the ignition key cylinder to the ON position.
Next, depress the retaining tab and remove the
Ignition key cylinder by pulling the key and cylin-
der straight out of the column together (Fig. 16).
Fig. 11 Interlock Cable
1 ± IGNITION SWITCH
2 ± CLIP
3 ± INTERLOCK CABLE
4 ± BTSI SOLENOID
Fig. 12 Steering Column Mounting Nuts
1 ± UPPER MOUNTING NUTS
2 ± STEERING COLUMN
3 ± LOWER MOUNTING NUTS
Fig. 13 Clockspring Electrical Connector
1 ± STEERING COLUMN
2 ± CLOCKSPRING
3 ± CLOCKSPRING ELECTRICAL CONNECTOR
4 ± IGNITION SWITCH ELECTRICAL CONNECTOR
Fig. 14 Electrical Connectors
1 ± MULTI-FUNCTION SWITCH ELECTRICAL CONNECTOR
2 ± WINDSHIELD WIPER SWITCH ELECTRICAL CONNECTOR
3 ± IGNITION SWITCH ELECTRICAL CONNECTOR
19 - 34 STEERINGPL
REMOVAL AND INSTALLATION (Continued)

(b) Disengage the latch hooks on the back of the
clockspring by lifting the clockspring slightly to
clear the column housing with the top latch hook.
Next, lower the clockspring slightly to do the same
for the lower latch hook (Fig. 17). Remove the
clockspring from the column.
(c) Remove the two screws securing the multi-
function/windshield wiper switch to the steering
column (Fig. 18). Pull the switch straight away
from the column to remove it.
(d) If the column is equipped with a SKIM,
remove the module from the column by removing
the two mounting screws and sliding the SKIM off
the non-halo trim ring (Fig. 19).
(e) Remove the non-halo trim ring from the col-
umn by unclipping it from the ignition cylinder
housing (Fig. 19).
(f) Remove the ignition switch from the steering
column by first removing the mounting screw (Fig.
20). Once the screw is removed, pull the switch
straight out away from the column ignition cylin-
der housing.
INSTALLATION
(1) If the steering column is being replaced, per-
form the following on the column before installing it
on the vehicle:
(a) Ensure the ignition switch is positioned in
the ON position.
(b) Install the ignition switch on the steering
column by pushing the tapered end onto the shaft
and steering column ignition cylinder housing.
Install the screw securing the switch to the column
(Fig. 20).(c) Install the non-halo trim ring on the column
until its tabs snap into place on the ignition cylin-
der housing (Fig. 19).
(d) If the column is equipped with a Sentry Key
Immobilizer Module (SKIM), install the module on
the column by sliding the module onto the non halo
trim ring and installing the two mounting screws
(Fig. 19). Tighten the mounting screws to a torque
of 3 N´m (25 in. lbs.).
(e) Position the multi-function/windshield wiper
switch in onto the top of the column and install the
two screws securing the switch in place (Fig. 18).
(f) Place the clockspring onto the end of the col-
umn engaging the clockspring latch hooks into the
column (Fig. 17).
Fig. 15 SKIM Electrical Connector
1 ± STEERING COLUMN
2 ± SKIM ELECTRICAL CONNECTOR
3 ± SKIM
Fig. 16 Ignition Key Cylinder Retaining Tab
1 ± IGNITION KEY
2 ± RETAINING TAB
3 ± STEERING COLUMN
Fig. 17 Clockspring Latch Hooks
1 ± CLOCKSPRING
2 ± LATCH HOOKS
3 ± STEERING COLUMN
PLSTEERING 19 - 35
REMOVAL AND INSTALLATION (Continued)

(M) Check Engine Lamp (MIL) will illuminate during engine operation if this Diagnostic Trouble Code was recorded.
P1684 The battery has been disconnected within the last 50
starts.
P1685 Skim Invalid Key The engine controler has received an invalid key from
the SKIM.
P1686 No SKIM BUS Messages Received No CCD/J1850 messages received from the Smart Key
Immobilizer Module (SKIM).
P1687 No MIC BUS Message No CCD/J1850 messages received from the Mechanical
Instrument Cluster (MIC) module.
P1693 DTC Detected in Companion
ModuleA fault has been generated in the companion engine
control module.
P1694 Fault In Companion Module No CCD/J1850 messages received from the powertrain
control module-Aisin transmission.
P1695 No CCD/J1850 Message From
Body Control ModuleNo CCD/J1850 messages received from the body
control module.
P1696 (M) PCM Failure EEPROM Write
DeniedUnsuccessful attempt to write to an EEPROM location
by the control module.
P1697 (M) PCM Failure SRI Mile Not Stored Unsuccessful attempt to update Service Reminder
Indicator (SRI or EMR) mileage in the control module
EEPROM.
P1698 (M) No CCD/J1850 Message From TCM No CCD/J1850 messages received from the electronic
transmission control module (EATX) or the Aisin
transmission controller.
P1719 Skip Shift Solenoid Circuit An open or shorted condition detected in the
transmission 2-3 gear lock-out solenoid control circuit.
P1756 GOV Press Not Equal to Target @
15-20 PSIThe requested pressure and the actual pressure are not
within a tolerance band for the Governor Control
System which is used to regulate governor pressure to
control shifts for 1st, 2nd, and 3rd gear. (Mid Pressure
Malfunction)
P1757 GOV Press Not Equal to Target @
15-20 PSIThe requested pressure and the actual pressure are not
within a tolerance band for the Governor Control
System which is used to regulate governor pressure to
control shifts for 1st, 2nd, and 3rd gear (Zero Pressure
Malfunction)
P1762 Gov Press Sen Offset Volts Too Lo
or HighThe Governor Pressure Sensor input is greater than a
calibration limit or is less than a calibration limit for 3
consecutive park/neutral calibrations.
P1763 Governor Pressure Sensor Volts
To o H iThe Governor Pressure Sensor input is above an
acceptable voltage level.
P1764 Governor Pressure Sensor Volts
Too LowThe Governor Pressure Sensor input is below an
acceptable voltage level.
P1765 Trans 12 Volt Supply Relay CTRL
CircuitAn open or shorted condition is detected in the
Transmission Relay control circuit. This relay supplies
power to the TCC>
P1899 (M) P/N Switch Stuck in Park or in Gear Incorrect input state detected for the Park/Neutral
switch.
25 - 14 EMISSION CONTROL SYSTEMSPL
DESCRIPTION AND OPERATION (Continued)