speaker DODGE RAM 1500 1998 2.G Owner's Manual

DEFROSTER DUCT
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
BAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.(1) Remove the instrument panel from the vehicle
(Refer to 23 - BODY/INSTRUMENT PANEL/IN-
STRUMENT PANEL ASSEMBLY - REMOVAL).
(2) Disconnect the wire harness connector from the
center radio speaker (Fig. 7).
(3) Position the speaker wire harness connector
out of the way.
(4) Remove the screw that secures the defroster
duct adapter to the instrument panel support.
(5) Remove the defroster duct adapter from the
defroster duct.
(6) Remove the six screws that secure the
defroster duct to the instrument panel.
(7) Remove the defroster duct from the instrument
panel.
INSTALLATION
(1) Install the defroster duct into the instrument
panel.
(2) Install the six screws that secure the defroster
duct to the instrument panel. Tighten the screws to
2.2 N´m (20 in.lbs.).
(3) Install the defroster duct adapter onto the
defroster duct.
(4) Install the screw that secures the defroster
duct adapter to the instrument panel support.
Tighten the screw to 2.2 N´m (20 in.lbs.).
(5) Connect the wire harness connector to the cen-
ter radio speaker.
(6) Install the instrument panel (Refer to 23 -
BODY/INSTRUMENT PANEL/INSTRUMENT
PANEL ASSEMBLY - INSTALLATION).
Fig. 6 HVAC Housing - Dual Zone Shown, Single
Zone Typical
1 - NUT
2 - PASSENGER BLEND DOOR ACTUATOR
3 - NUT
4 - INLET BAFFLE
5 - RECIRCULATION DOOR ACTUATOR
6 - RECIRCULATION DOOR
7 - DRIVER SIDE BLEND DOOR ACTUATOR
8 - HVAC HOUSING
9 - BOLT
10 - DEFROSTER DOOR ACTUATOR
11 - MODE DOOR ACTUATOR
24 - 32 DISTRIBUTIONDR
DEFROST DOOR (Continued)

FLOOR DISTRIBUTION DUCT
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN AN ACCIDENTAL
AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
(1) Remove the HVAC housing from the vehicle
(Refer to 24 - HEATING & AIR CONDITIONING/
DISTRIBUTION/HVAC HOUSING - REMOVAL).
(2) Remove the screws that secure the floor distri-
bution duct to the bottom of the HVAC housing.
(3) Remove the floor distribution duct from the
HVAC housing.
Fig. 7 Defroster Duct
1 - SPEAKER WIRE HARNESS CONNECTOR
2 - DEFROSTER DUCT SCREWS (6)
3 - DEFROSTER DUCT ADAPTER4 - DEFROSTER DUCT ADAPTER SCREW
5 - DEFROSTER DUCT
Fig. 8 Floor Distribution Duct
1 - FLOOR DISTRIBUTION DUCT
2 - HVAC HOUSING
3 - SCREWS (5)
DRDISTRIBUTION 24 - 33
DEFROSTER DUCT (Continued)

SOLENOID - DESCRIPTION, EVAP/PURGE . 25-12
SOLENOID - INSTALLATION, EVAP/
PURGE.............................25-12
SOLENOID - OPERATION..............21-252
SOLENOID - OPERATION, EVAP/PURGE . . . 25-12
SOLENOID - REMOVAL, EVAP/PURGE.....25-12
SOLENOID SWITCH VALVE -
DESCRIPTION......................21-398
SOLENOID SWITCH VALVE - OPERATION . 21-398
SOLENOIDS - DESCRIPTION...........21-398
SOLENOIDS - OPERATION.............21-399
SOLENOID/TRS ASSEMBLY -
DESCRIPTION, TRANSMISSION........21-406
SOLENOID/TRS ASSEMBLY -
INSTALLATION, TRANSMISSION........21-408
SOLENOID/TRS ASSEMBLY -
OPERATION, TRANSMISSION..........21-406
SOLENOID/TRS ASSEMBLY - REMOVAL,
TRANSMISSION.....................21-407
SOLID LIFTERS/TAPPETS - CLEANING....9-279
SOLID LIFTERS/TAPPETS - INSPECTION . . 9-279
SOLID LIFTERS/TAPPETS -
INSTALLATION.......................9-280
SOLID LIFTERS/TAPPETS - REMOVAL....9-279
SPARE / TEMPORARY TIRE -
DESCRIPTION.......................22-15
SPARE TIRE / TEMPORARY -
DESCRIPTION........................22-6
SPARE WHEEL WITH MATCHING TIRE -
DESCRIPTION, FULL SIZE..............22-15
SPARK PLUG - DESCRIPTION...........8I-17
SPARK PLUG - REMOVAL..............8I-19
SPARK PLUG CABLE - DESCRIPTION.....8I-21
SPARK PLUG CABLE - INSTALLATION.....8I-22
SPARK PLUG CABLE - OPERATION.......8I-21
SPARK PLUG CABLE - REMOVAL........8I-22
SPARK PLUG CABLE RESISTANCE,
SPECIFICATIONS......................8I-4
SPARK PLUG CONDITIONS - DIAGNOSIS
AND TESTING........................8I-17
SPARK PLUGS, SPECIFICATIONS..........8I-4
SPEAKER - DESCRIPTION..............8A-13
SPEAKER - DIAGNOSIS AND TESTING....8A-13
SPEAKER - INSTALLATION.............8A-15
SPEAKER - OPERATION...............8A-13
SPEAKER - REMOVAL.................8A-14
SPECIFICATIONS......................7-20
SPEED CONTROL - DESCRIPTION........8P-1
SPEED CONTROL - OPERATION..........8P-2
SPEED CONTROL - TORQUE.............8P-3
SPEED SENSOR - DESCRIPTION........21-253
SPEED SENSOR - DESCRIPTION, FRONT
WHEEL.............................5-47
SPEED SENSOR - DESCRIPTION, INPUT . 21-382
SPEED SENSOR - DESCRIPTION,
OUTPUT...........................21-391
SPEED SENSOR - DIAGNOSIS AND
TESTING, REAR WHEEL................5-49
SPEED SENSOR - INSTALLATION, FRONT
WHEEL.............................5-48
SPEED SENSOR - INSTALLATION, INPUT . 21-382
SPEED SENSOR - INSTALLATION,
OUTPUT...........................21-392
SPEED SENSOR - INSTALLATION, REAR
WHEEL.............................5-48
SPEED SENSOR - OPERATION.........21-253
SPEED SENSOR - OPERATION, FRONT
WHEEL.............................5-47
SPEED SENSOR - OPERATION, INPUT . . . 21-382
SPEED SENSOR - OPERATION, OUTPUT . . 21-391
SPEED SENSOR - REMOVAL, FRONT
WHEEL.............................5-48
SPEED SENSOR - REMOVAL, INPUT.....21-382
SPEED SENSOR - REMOVAL, OUTPUT . . . 21-391
SPEED SENSOR - REMOVAL, REAR
WHEEL.............................5-48
SPEEDOMETER - DESCRIPTION.........8J-37
SPEEDOMETER - OPERATION...........8J-37
SPEEDS - DESCRIPTION, TIRE
PRESSURE FOR HIGH
..................22-7
SPLASH SHIELD - INSTALLATION,
FRONT WHEELHOUSE
.................23-41
SPLASH SHIELD - INSTALLATION, REAR
WHEELHOUSE
.......................23-41
SPLASH SHIELD - REMOVAL, FRONT
WHEELHOUSE
.......................23-41
SPLASH SHIELD - REMOVAL, REAR
WHEELHOUSE
.......................23-41SPLICE INFORMATION - DESCRIPTION,
CONNECTOR, GROUND..............8W-01-7
SPLICING - STANDARD PROCEDURE,
WIRE...........................8W-01-15
SPRING - DESCRIPTION................2-44
SPRING - INSTALLATION.......2-23,2-39,2-44
SPRING - OPERATION..................2-44
SPRING - REMOVAL...........2-22,2-39,2-44
SPRING AND SHOCK - DIAGNOSIS AND
TESTING............................2-41
SPRING BUMPERS (3500) -
INSTALLATION, AUXILIARY..............2-43
SPRING BUMPERS (3500) - REMOVAL,
AUXILIARY..........................2-43
SPRING TIP INSERTS - INSTALLATION....2-45
SPRING TIP INSERTS - REMOVAL........2-44
SPRINGS - DESCRIPTION, VALVE . . . 9-126,9-32,
9-38
SPRINGS - INSTALLATION, VALVE . . 9-127,9-204,
9-32,9-38
SPRINGS - REMOVAL, VALVE . 9-126,9-204,9-32,
9-38
SPRINGS - STANDARD PROCEDURE,
VALVES, GUIDES.....................9-256
SPRINGS AND SEALS - REMOVAL,
VALVE .............................9-260
SPROCKETS - INSPECTION, TIMING
BELT/CHAIN.....................9-174,9-84
SPROCKETS - INSTALLATION, TIMING
BELT/CHAIN.....................9-176,9-85
SPROCKETS - INSTALLATION,
TIMING/CHAIN........................9-228
SPROCKETS - REMOVAL, TIMING
BELT/CHAIN.....................9-172,9-83
SPROCKETS - REMOVAL, TIMING/CHAIN . . 9-228
SQUEAK & RATTLE - STANDARD
PROCEDURE, BUZZ...................23-11
STABILIZER BAR - DESCRIPTION.........2-24
STABILIZER BAR - INSTALLATION....2-25,2-40
STABILIZER BAR - OPERATION...........2-25
STABILIZER BAR - REMOVAL........2-25,2-39
STAKING - STANDARD PROCEDURE,
HEAT ...............................23-3
STANDARD CAB - INSTALLATION . . 8O-35,8O-61
STANDARD CAB - REMOVAL......8O-32,8O-59
STARTER MOTOR - DIAGNOSIS AND
TESTING...........................8F-32
STARTER MOTOR - INSTALLATION.......8F-34
STARTER MOTOR - REMOVAL..........8F-33
STARTER MOTOR RELAY - DESCRIPTION . 8F-35
STARTER MOTOR RELAY -
INSTALLATION.......................8F-37
STARTER MOTOR RELAY - OPERATION . . . 8F-36
STARTER MOTOR RELAY - REMOVAL.....8F-37
STARTER RELAY - DIAGNOSIS AND
TESTING...........................8F-36
STARTING - DESCRIPTION.............8F-26
STARTING - OPERATION...............8F-26
STARTING - STANDARD PROCEDURE,
JUMP...............................0-19
STARTING SYSTEM - DIAGNOSIS AND
TESTING...........................8F-27
STARTING SYSTEM - SPECIFICATIONS,
TORQUE............................8F-32
STARTING SYSTEM, SPECIFICATIONS
.....8F-31
STATE DISPLAY TEST MODE -
DESCRIPTION
........................25-1
STEERING - DESCRIPTION
..............19-1
STEERING - OPERATION
................19-1
STEERING COLUMN - DIAGNOSIS AND
TESTING
............................19-7
STEERING COLUMN OPENING COVER -
INSTALLATION
.......................23-60
STEERING COLUMN OPENING COVER -
REMOVAL
..........................23-60
STEERING COLUMN OPENING SUPPORT
BRACKET - INSTALLATION
.............23-60
STEERING COLUMN OPENING SUPPORT
BRACKET - REMOVAL
.................23-60
STEERING COUPLING - INSTALLATION,
UPPER
.............................19-13
STEERING COUPLING - REMOVAL,
UPPER
.............................19-13
STEERING FLOW AND PRESSURE -
DIAGNOSIS AND TESTING, POWER
.......19-4
STEERING FLUID - DESCRIPTION,
POWER
..............................0-3STEERING FLUID LEVEL CHECKING -
STANDARD PROCEDURE, POWER.......19-43
STEERING GEAR INPUT SHAFT SEAL -
INSTALLATION.......................19-29
STEERING GEAR INPUT SHAFT SEAL -
REMOVAL..........................19-27
STEERING GEAR, SPECIAL TOOLS -
POWER............................19-23
STEERING GEAR, SPECIFICATIONS -
POWER............................19-22
STEERING LINKAGE, SPECIAL TOOLS....19-35
STEERING PRESSURE SWITCH -
DESCRIPTION, POWER................19-46
STEERING PRESSURE SWITCH -
OPERATION, POWER..................19-46
STEERING PUMP - INITIAL OPERATION -
STANDARD PROCEDURE, POWER.......19-40
STEERING, SPECIAL TOOLS.............19-5
STEERING SYSTEM - DIAGNOSIS AND
TESTING, POWER.....................19-2
STEERING SYSTEM - STANDARD
PROCEDURE, FLUSHING POWER........19-40
STEERING WHEEL - INSTALLATION......19-15
STEERING WHEEL - REMOVAL..........19-15
STEM SEALS - DESCRIPTION, VALVE....9-127,
9-203
STOP LAMP - INSTALLATION, CENTER
HIGH MOUNTED.....................8L-11
STOP LAMP - REMOVAL, CENTER HIGH
MOUNTED..........................8L-11
STOP LAMP UNIT - INSTALLATION,
CENTER HIGH MOUNTED..............8L-11
STOP LAMP UNIT - REMOVAL, CENTER
HIGH MOUNTED.....................8L-11
STORAGE BIN - INSTALLATION..........23-61
STORAGE BIN - INSTALLATION, UNDER
SEAT ..............................23-80
STORAGE BIN - REMOVAL.............23-61
STORAGE BIN - REMOVAL, UNDER SEAT . . 23-80
STORAGE BIN COVERING -
INSTALLATION, UNDER SEAT...........23-80
STORAGE BIN COVERING - REMOVAL,
UNDER SEAT........................23-80
STORAGE BIN LATCH - INSTALLATION,
UNDER SEAT........................23-80
STORAGE BIN LATCH - REMOVAL,
UNDER SEAT........................23-80
STORAGE BIN LID - INSTALLATION,
UNDER SEAT........................23-80
STORAGE BIN LID - REMOVAL, UNDER
SEAT ..............................23-80
STRAP - DESCRIPTION, RADIO NOISE
SUPPRESSION GROUND................8A-9
STRAP - INSTALLATION, RADIO NOISE
SUPPRESSION GROUND...............8A-10
STRAP - OPERATION, RADIO NOISE
SUPPRESSION GROUND................8A-9
STRAP - REMOVAL, RADIO NOISE
SUPPRESSION GROUND................8A-9
STRIKER - INSTALLATION, LATCH . . 23-17,23-23,
23-33
STRIKER - REMOVAL, LATCH . 23-16,23-23,23-33
STRIKER / SECONDARY CATCH -
INSTALLATION, LATCH................23-48
STRIKER / SECONDARY CATCH -
REMOVAL, LATCH....................23-47
STRUCTURAL ADHESIVE LOCATIONS -
SPECIFICATIONS....................23-112
STRUCTURAL COVER - DESCRIPTION....9-145,
9-216,9-57
STRUCTURAL COVER - INSTALLATION . . . 9-145,
9-216,9-57
STRUCTURAL COVER - OPERATION.....9-145,
9-216,9-57
STRUCTURAL COVER - REMOVAL . . 9-145,9-216,
9-57
STUDS - INSTALLATION...............22-14
STUDS - REMOVAL...................22-14
SUCTION LINE - DESCRIPTION..........24-70
SUN VISOR - INSTALLATION...........23-70
SUN VISOR - REMOVAL
...............23-70
SUN VISOR SUPPORT - INSTALLATION
. . . 23-71
SUN VISOR SUPPORT - REMOVAL
.......23-70
SUPPLEMENTAL RESTRAINT
DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER A
.........8O-7
SUPPLEMENTAL RESTRAINT SYSTEM -
DIAGNOSIS AND TESTING
..............8O-6
DRINDEX 31
Description Group-Page Description Group-Page Description Group-Page