Ignition system DODGE RAM 1999 Service User Guide

AIR B AG R ESTR AIN T S YSTE M
1999 D odge P ic ku p R 1500
1999 AIR BAG RESTRAINT SYSTEMS
DaimlerChrysler Corp.
Dodge: Ram Pickup
DESCRIPTION & OPERATION
* PLEASE READ THIS FIRST *
WARNING: To avoid injury from accidental air bag deployment, read and
carefully follow all WARNINGS and SERVICE PRECAUTIONS.
Supplemental Restraint System (SRS) is designed to work in
conjunction with seat belts. SRS helps to reduce the risk or severity
of serious injury during a front-end collision. Driver-side air bag is
stored in a module in steering wheel hub. All models are equipped with
passenger-side air bags. Passenger-side air bag is stored in the
instrument panel, above glove box. All air bags are covered by a pad
bearing the air bag SRS logo.
Air bag(s) inflate and deflate within 1/10th of a second of
impact sensor switches closing. This creates a cushion of air between
driver and steering wheel and passenger and instrument panel.
System consists of an AIR BAG warning light, clockspring,
driver-side and passenger-side air bag modules, Air Bag Control Module
(ACM), one impact sensor (located inside ACM) and an energy reserve
capacitor. The ACM monitors system, stores fault codes (messages) and
provides information to AIR BAG warning light and Data Link Connector
(DLC). When a malfunction occurs, a fault code is stored and AIR BAG
warning light is activated for more than 12 seconds.
When impact sensor registers sufficient deceleration force
during a front-end collision, an electrical charge is sent from ACM to
air bag module inflator via the clockspring. Inflator actuates and
produces nitrogen gas, which inflates air bag(s).
AIR BAG WARNING LIGHT
Whenever ignition switch is in RUN or START position, AIR BAG
warning light on instrument panel will illuminate for 6-8 seconds and
then turn off. This signifies ACM has checked the system and found
that it is functioning properly. If AIR BAG warning light illuminates
for 12 seconds or more, stays on all the time or does not come on, a
system malfunction exists and trouble code will be stored.
IMPACT SENSOR
All models have one impact sensor located inside ACM. Impact
sensor is an accelerometer that measures deceleration. During a front-
end collision, a signal is sent that completes an electrical circuit
to inflators. Inflators actuate and produce nitrogen gas, which
inflates each air bag. Impact sensor is calibrated for a specific
vehicle and react to severity and direction of vehicle impact.
AIR BAG MODULE
WARNING: DO NOT attempt to disassemble air bag modules. Air bag
modules are not serviceable.
Driver-Side
Air bag module is mounted on front face of steering wheel. A

PASSENGER AIR BAG DISARM (PAD) SWITCH
PAD switch is mounted on instrument panel. Switch allows
passenger-side airbag module to be disarmed when rear facing child
safety seat is being used. PAD switch is operated with ignition key.
SYSTEM OPERATION CHECK
Turn ignition on and observe AIR BAG warning light. AIR BAG
warning light should illuminate for 6-8 seconds and then go out,
indicating system is functioning properly. If AIR BAG warning light
either fails to illuminate or illuminates continuously, a system
malfunction exists. Perform self-diagnostics. See DIAGNOSIS & TESTING.
After completing necessary repairs, turn ignition switch to
ON position. Ensure no one is inside vehicle, then connect negative
battery cable. Using DRB, erase stored Diagnostic Trouble Codes (DTC).\
See DIAGNOSIS & TESTING .
SERVICE PRECAUTIONS
These precautions should be observed when working with air
bag systems:
* Disable air bag system before servicing any air bag system
or steering column component. Failure to do this could
result in accidental air bag deployment and possible
personal injury. See DISABLING & ACTIVATING AIR BAG SYSTEM .
* Back-up power supply maintains deployment voltage for about
2 minutes after battery is disconnected. When disabling air
bag system, always wait at least 2 minutes after
disconnecting battery cables to resume procedure.
* After repairs, ensure AIR BAG warning light works
properly and no system faults are indicated. See
SYSTEM OPERATION CHECK .
* Always wear safety glasses when servicing or handling an
air bag.
* All SRS component fasteners are specially coated and are
designed with a specific function. Never replace SRS
component fasteners with other than original equipment parts.
* Air bag module must be stored in its original special
container until used for service. It must be stored in a
clean, dry, place, away from sources of extreme heat, sparks
and high electrical energy.
* When placing a live air bag on a bench or other surface,
always face air bag and trim cover up, away from surface.
This will reduce motion of module if accidentally deployed.
* After deployment, air bag surface may contain deposits of
sodium hydroxide, which irritates skin. Always wear safety
glasses, rubber gloves, and long-sleeved shirt during
clean-up and wash hands using mild soap and water. Follow
correct disposal procedures. See DISPOSAL PROCEDURES.
* Because of critical system operating requirements, DO NOT
attempt to service any air bag components. Corrections are
only made by replacing defective part.
* Electrical sources should never be allowed near inflator on
back of air bag module.
* When carrying a live air bag module, trim cover should be
pointed away from your body to minimize injury in case of
deployment.
* When testing voltage or continuity at Air Bag Control Module

(ACM), use wire side (not terminal end) of connector.
* DO NOT probe a wire through insulator, as this will damage
it and eventually cause failure.
* When performing electrical tests, prevent accidental
shorting of terminals. Such shorts can damage fuses or
components and may cause a second fault code to set, making
diagnosis of original problem more difficult.
* When diagnosing air bag system, use DRB volt/ohmmeter
unless instructed to use an external volt/ohmmeter. NEVER
use an analog volt/ohmmeter or test light in place of a
digital volt/ohmmeter.
* When using DRB to diagnose an air bag system problem,
operate DRB from outside of vehicle. DO NOT sit inside of
vehicle.
* Never use an ohmmeter to measure resistance of air bag
module. Accidental air bag deployment may occur, causing
personal injury.
* If air bag system is not fully functional for any reason,
vehicle should not be driven until system is repaired and
again becomes operational. DO NOT remove bulbs, modules,
sensors, or other components or in any way disable system
from operating normally. If air bag system is not
functional, park vehicle until it is repaired and functions
properly.
* When battery is disconnected, vehicle computer and memory
systems may lose memory data. Driveability problems may
exist until computer systems have completed a relearn cycle.
See COMPUTER RELEARN PROCEDURES in GENERAL INFORMATION
before disconnecting battery.
DISABLING & ACTIVATING AIR BAG SYSTEM
WARNING: Wait at least 2 minutes after disconnecting negative battery
cable before servicing air bag system. System reserve
capacitor, integral to ACM, maintains air bag system voltage
for about 2 minutes after battery is disconnected. Servicing
air bag system before 2-minute period may cause accidental
deployment of air bag(s) and possible personal injury. DO NOT\
use computer system memory saving devices. Enough voltage to
deploy air bag(s) may be provided from device.
CAUTION: When battery is disconnected, vehicle computer and memory
systems may lose memory data. Driveability problems may
exist until computer systems have completed a relearn cycle.
See COMPUTER RELEARN PROCEDURES in GENERAL INFORMATION
before disconnecting battery.
Disabling System
To disable air bag system for repairs, ensure ignition switch
is in OFF position. Disconnect and shield negative battery cable.
After disconnecting negative battery cable, wait at least 2 minutes
for reserve capacitor to discharge before servicing air bag system.
Activating System
Reconnect negative battery cable. From a position clear of air bag(s),\
turn ignition on. Perform system operation check. See
SYSTEM OPERATION CHECK .
DISPOSAL PROCEDURES
DEPLOYED AIR BAG CLEAN-UP

CAUTION: When removing a deployed air bag, wear eye protection, rubber
gloves and a long-sleeve shirt. Powder residue from air bag
deployment may irritate skin and eyes.
CAUTION: Before removing steering wheel, position front wheels in
straight-ahead position and lock steering column by removing
ignition key. Failure to do so could damage clockspring or
cause clockspring to be off-centered. DO NOT hammer on
steering wheel during removal, or collapsible column could be
damaged.
Removal
1) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM . Air bag module
is mounted on face of steering wheel. Ensure wheels are pointed
straight-ahead and steering wheel is locked.
2) Remove air bag module-to-steering wheel screws from back
side of steering wheel. Lift air bag module and disconnect electrical
connectors from rear of module.
Installation
Connect air bag, cruise control and horn harness connectors
to rear of air bag module. Secure module to steering wheel. Tighten
air bag module-to-steering wheel screws to specification. See
TORQUE SPECIFICATIONS . DO NOT connect negative battery cable at this
time. Go to SYSTEM OPERATION CHECK .
PASSENGER-SIDE AIR BAG MODULE
Removal
1) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Open glove box. Holding glove box door, push center of
glove box bin towards front of vehicle. Flex glove box bin far enough
so glove box stops will clear sides of instrument panel opening. Roll
glove box down until stop bumpers are beyond sides of instrument panel
opening. Release bin. Lift bottom of glove box upward to disengage
hinge hooks form hinge pins.
3) Remove 3 screws securing instrument panel glove box
opening upper trim strip to instrument panel glove box opening upper
reinforcement, then remove trim strip. Remove 4 screws that secure 2
plastic support brackets of passenger-side air bag door panel outlet
housing to glove box opening upper reinforcement.
4) Reach through and above glove box opening to access and
disconnect air bag module harness connector. Remove 2 screws securing
passenger-side air bag module front bracket to instrument panel
structural support. Remove 3 screws securing passenger-side air bag
module rear bracket to glove box opening upper reinforcement.
5) Using trim stick, gently pry passenger-side air bag door
(starting at lower left edge) away from instrument panel top cover.
Remove air bag module, air bag door and panel outlet housing and
barrel assembly from instrument panel as a unit.
Installation
To install, reverse removal procedure. Ensure air bag door is
securely attached to instrument panel. Ensure air bag harness
connector latches fully engaged. DO NOT connect negative battery cable
at this time. Go to SYSTEM OPERATION CHECK .
CLOCKSPRING
CAUTION: Failure to position wheels in the straight-ahead position
with steering wheel locked when removing steering wheel could

damage clockspring and/or require clockspring to be
readjusted.
NOTE: Clockspring is self-centering and will automatically lock in
the centered position when steering wheel is removed.
Adjustment is only required if centering position is
disturbed.
Removal
1) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Clockspring is located behind steering wheel. See Fig. 1.
Ensure front wheels are in straight-ahead position. Lock steering
wheel. Remove air bag module. See AIR BAG MODULE.
3) Remove steering wheel nut. Using appropriate steering
wheel puller, remove steering wheel. When steering wheel is removed,
self-centering clockspring will automatically lock in place. Remove
upper and lower steering column shrouds to gain access to clockspring
wiring.
4) Remove knee bolster (if equipped). Disconnect Yellow 2-wa\
y
clockspring harness connector between clockspring and instrument panel
wiring harness, at base of steering column. See Fig. 13. Remove
clockspring by releasing 2 tabs on side of clockspring. Clockspring
cannot be repaired and must be replaced if faulty.
Installation
1) Snap clockspring onto steering column. If clockspring
centering adjustment is disturbed, adjust clockspring before
installing steering wheel. See CLOCKSPRING CENTERING under
ADJUSTMENTS. Connect clockspring wiring connectors. Install steering
column covers. Install knee bolster (if removed).
2) Position steering wheel on steering column. Ensure flats
on steering wheel hub fit formations on inside of clockspring. Pull
clockspring, cruise control switch (if equipped) and horn wires
through lower large holes and upper small holes in steering wheel.
3) Install steering wheel retaining nut and tighten to 45 ft.
lbs. (61 N.m). Connect horn and cruise control wires (if equipped).
Connect clockspring wire to air bag module. To ensure complete
connector connection, latching arms must be visible on top of
connector housing. DO NOT connect negative battery cable at this time.
Go to SYSTEM OPERATION CHECK .
PASSENGER AIR BAG DISARM (PAD) SWITCH
Removal & Installation
1) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) If vehicle is equipped with automatic transmission, turn
ignition switch to UNLOCK position, set parking brake and place
transmission selector lever in LOW position. Tilt steering column to
lowest position (if equipped). Using trim stick, gently pry around
perimeter of cluster bezel and remove bezel.
3) Open glove box. Holding glove box door, push center of
glove box bin towards front of vehicle. Flex glove box bin far enough
so glove box stops will clear sides of instrument panel opening. Roll
glove box down until stop bumpers are beyond sides of instrument panel
opening. Release bin. Lift bottom of glove box upward to disengage
hinge hooks form hinge pins.
4) Reach through glove box opening to access and disconnect 2
passenger-side air bag disarm switch harness connectors. Connectors
are attached to bracket located on inboard glove box opening
reinforcement. See Fig. 4. Remove 3 screws retaining passenger-side
air bag disarm switch bezel to instrument panel.

as the malfunction is detected. A stored code indicates there was an
active code present at some time. However, the code currently may not
be present as an active code, although another active code could be.
When a trouble code occurs, the AIR BAG warning light
illuminates for 12 seconds minimum (even if problem existed for less
than 12 seconds). Code is stored, along with time in minutes it was
active, and number of times ignition has been cycled since problem was
detected.
When and if malfunction ceases to exist, an ignition cycle
count will be initiated for that code. If ignition cycle count reaches
100 without a reoccurrence of the same malfunction, DTC is erased and
that ignition cycle counter is reset to zero. If malfunction reoccurs
before count reaches 100, ignition cycle counter will be reset and DTC
will continue to be a stored code.
If a particular code is not active while performing
diagnostic test for that code, code diagnostic test may not locate the
source of the problem. In this case, stored code can only indicate an
area of system to inspect.
If no obvious problems are found, erase stored codes, and
with ignition on, wiggle wiring harness and connectors. Recheck for
codes periodically as you work through system. This procedure may
uncover a difficult problem to locate.
PRETEST INSPECTION & DIAGNOSTIC PROCEDURE
Following precautions and procedures must be followed:
* Always follow air bag service precautions to avoid air bag
deployment and possible personal injury. Refer to procedure
under See SERVICE PRECAUTIONS.
* After component replacement, ensure proper system operation.
See SYSTEM OPERATION CHECK .
* When testing voltage or continuity at ACM, use terminal side
(not wire end) of connector. DO NOT probe wire through
insulation.
* Always check if any TECH SERVICE BULLETINS (TSBs) apply to
vehicle.
* When using diagnostic charts, DO NOT skip any steps in chart
or incorrect diagnosis may result. Always perform
SYSTEM OPERATION CHECK after repairs are made.
* Always use most current DRB diagnostic program cartridge
available to prevent erroneous codes or test results.
* When using diagnostic charts, use DRB voltmeter unless
instructed to use an external voltmeter. Never use a test
light in place of a voltmeter.
* When performing electrical tests, prevent accidental
shorting of terminals. Such shorts can damage fuses or
components and may cause a second code (message) to be
set, making diagnosis of original problem more difficult.
* Vehicle must have a fully-charged battery and functional
charging system.
* Each time a connector is disconnected, inspect it to ensure
it is in good condition. Always focus on circuit being
tested. Dirt, water and corrosion, are most common problems
in connectors.
* Always disconnect DRB after use.
* Always disconnect DRB before charging battery.
USING DRB
1) Refer to DRB user guide for instructions and assistance
with reading trouble codes and other DRB functions. Under normal
operation DRB will display one of only 2 error messages: User-

3) Using DRB, read stored codes. If DRB displays stored
codes, perform appropriate diagnostic test. If DRB does not display
any stored codes, system is operating properly at this time.
COMPONENT VERIFICATION TEST
Reconnect all previously disconnected components and
connectors. Turn ignition on (engine off). Fully operate system that
was malfunctioning. If system operates properly, repair is complete.
If system does not operate properly, go to appropriate diagnostic
test.
VEHICLE COMMUNICATIONS
VEHICLE COMMUNICATION PROBLEMS
NOTE: Use this test only when instructed to do so by another
diagnostic test. Due to manufacturer changes in wire
colors, use terminal identification whenever possible.
DRB Blank Screen
If DRB Screen is blank, disconnect DRB from data link
connector. Ensure good ground exists at data link connector terminal
No. 4 (Black/Tan wire). Ensure 12-volts exists at data link connector
terminal No. 16 (Pink wire). If 12-volts does not exist, check for
blown fuse No. 12 located in power distribution center. If no problems
can be found, try a different DRB cable and/or a different DRB.
No Response Condition
If no response condition from Air Bag Control Module (ACM)
exists, go to NO RESPONSE FROM AIR BAG CONTROL MODULE .
NO RESPONSE FROM AIR BAG CONTROL MODULE
NOTE: Perform COMPONENT VERIFICATION TEST under DIAGNOSTIC TESTS
after all repairs. Each time a connector is disconnected,
inspect it to ensure it is in good condition. Always focus on
circuit being tested. Dirt, water and corrosion, are most
common problems in connectors. Due to manufacturer changes in
wire colors, use terminal identification whenever possible.
1) Remove and inspect fuse No. 19. If fuse is blown, go to
OPEN FUSED IGNITION SWITCH OUTPUT (RUN/START) CKT . If not, go to next
step.
2) Using a voltmeter, measure ignition switch output
RUN/START at fuse No. 19. See WIRING DIAGRAMS. If voltage is more than
10 volts, go to next step. If voltage is less than 10 volts, repair
open ignition switch output RUN/START circuit.
3) Turn ignition off and wait 2 minutes. Disconnect ACM
connector. Reinstall fuse No. 19. Turn ignition on (engine off). Using\
a voltmeter, check voltage at ACM connector terminal No. 14 (Light
Green/Yellow wire). If voltage is more than 10 volts, go to next step.
If voltage is less than 10 volts, repair open in Light Green/Yellow
wire.
4) Turn ignition off. Using DRB in ohmmeter mode, check
resistance at ACM connector terminal No. 4 (Black/Pink wire). If
resistance is more than 5 ohms, repair open in Black/Pink wire. If
resistance is less than 5 ohms, go to next step.
5) Turn ignition on (engine off). Using DRB in voltmeter
mode, check voltage at ACM connector terminal No. 21 (Violet/Brown
wire). If voltage is 1.8-2.6 volts, go to next step. If voltage is not
1.8-2.6 volts, repair open in Violet/Brown wire.

inspect it to ensure it is in good condition. Always focus on
circuit being tested. Dirt, water and corrosion, are most
common problems in connectors. Due to manufacturer changes in
wire colors, use terminal identification whenever possible.
1) Ensure ignition switch is in the RUN position. Disconnect
Powertrain Control Module (PCM) connectors. If DRB does not display
BUS SHORT TO BATTERY, to step 8). If DRB displays BUS SHORT TO
BATTERY, go to next step.
2) Disconnect instrument cluster connectors. If DRB does not
display BUS SHORT TO BATTERY, replace instrument cluster. If DRB
displays BUS SHORT TO BATTERY, go to next step.
3) Turn ignition off and wait 2 minutes before proceeding.
Disconnect air bag control module connector. Turn ignition on (engine
off). If DRB does not display SHORT TO BATTERY, replace ACM. If DRB
displays SHORT TO BATTERY, go to next step.
4) Disconnect Central Timer Module (CTM) 18-pin connector. I\
f
DRB does not display BUS SHORT TO BATTERY, replace CTM. If DRB
displays BUS SHORT TO BATTERY, go to next step.
5) Disconnect anti-lock brake controller. If DRB does not
display BUS SHORT TO BATTERY, replace anti-lock brake controller. If
DRB displays BUS SHORT TO BATTERY, go to next step.
6) Disconnect DRB from Data Link Connector (DLC). Using a
voltmeter, check voltage between ground and DLC connector terminal No.
3 (Violet/Brown wire). If voltage is more than 0.2 volt, repair short
in Violet/Brown wire. If voltage is less than 0.2 volt, go to next
step.
7) Using a voltmeter, check voltage between ground and DLC
connector terminal No. 11 (White/Black wire). If voltage is more than
0.2 volt, repair short in White/Black wire. If voltage is less than 0.
2 volt, replace DRB or DRB cable as necessary.
8) Turn ignition off. Using an ohmmeter, check resistance
between ground and PCM Black connector terminal A31 (Black/Tan wire).
If resistance is more than 10 ohms, repair open in Black/Tan wire). If
resistance is less than 10 ohms, go to next step.
9) Using an ohmmeter, check resistance between ground and PCM
Black connector terminal A32 (Black/Tan wire). If resistance is more
than 10 ohms, repair open in Black/Tan wire). If resistance is less
than 10 ohms, replace Powertrain Control Module (PCM).
NO RESPONSE FROM INSTRUMENT CLUSTER
NOTE: Perform COMPONENT VERIFICATION TEST under DIAGNOSTIC TESTS
after all repairs. Each time a connector is disconnected,
inspect it to ensure it is in good condition. Always focus on
circuit being tested. Dirt, water and corrosion, are most
common problems in connectors. Due to manufacturer changes in
wire colors, use terminal identification whenever possible.
1) Remove Instrument cluster. Using DRB, turn on INTERNAL BUS
BIAS under SYSTEM MONITORS CCD BUS VOLTAGE. Connect a jumper wire from
Black instrument cluster 10-pin connector "A" terminal No. 9
(White/Black wire) to ground. Observe CCD BUS voltage on DRB. If
voltage did not drop to about zero volt, repair open in White/Black
wire. If voltage drops to about zero volt, go to next step.
2) Leave internal DRB CCD BUS BIAS turned on. Connect a
jumper wire from ground to Black instrument cluster 10-pin connector
"A" terminal No. 10 (Violet/Brown wire). Go to next step.
3) Observe CCD BUS voltage on DRB. If voltage did not drop to
about zero volt, repair open in Violet/Brown wire. If voltage drops to
about zero volt, replace instrument cluster.

AN TI- L O CK B RAK E S A FE TY P R EC AU TIO NS

1999 D odge P ic ku p R 1500
GENERAL INFORMATION
Anti-Lock Brake Safety Precautions
* PLEASE READ THIS FIRST *
This article is intended for general information purposes
only. This information may not apply to all makes and models. If
vehicle is equipped with Anti-Lock Brake System (ABS), refer to
appropriate ANTI-LOCK BRAKE SYSTEM article in the BRAKES section for
description, operation, depressurizing, testing, system bleeding,
trouble shooting and servicing of specific system.
WARNING: Failure to depressurize ABS could lead to physical injury.
ANTI-LOCK BRAKE SAFETY PRECAUTIONS
WARNING: Failure to depressurize ABS could lead to physical injury.
* NEVER open a bleeder valve or loosen a hydraulic line
while ABS is pressurized.
* NEVER disconnect or reconnect any electrical connectors
while ignition is on. Damage to ABS control unit may result.
* DO NOT attempt to bleed hyudarulic system without first
referring to the appropriate ANTI-LOCK BRAKE SYSTEM article
in the BRAKES section.
* Only use specially designed brake hoses/lines on ABS equipped
vehicles.
* DO NOT tap on speed sensor components (sensor, sensor rings).
Sensor rings must be pressed into hubs, NOT hammered into
hubs. Striking these components can cause demagnetization or
a loss of polarization, affecting the accuracy of the speed
signal returning to the ABS control unit.
* DO NOT mix tire sizes. Increasing the width, as long as tires
remain close to the original diameter, is acceptable. Rolling
diameter must be identical for all 4 tires. Some
manufacturers recommend tires of the same brand, style and
type. Failure to follow this precaution may cause inaccurate
wheel speed readings.
* DO NOT contaminate speed sensor components with grease. Only
use recommended coating, when system calls for an
anti-corrosion coating.
* When speed sensor components have been removed, ALWAYS check
sensor-to-ring air gaps when applicable. These specifications
can be found in each appropriate article.
* ONLY use rocommended brake fluids. DO NOT use silicone brake
fluids in an ABS equipped vehicle.
* When instlling transmittion devices (CB's, telephones, etc.)
on ABS equipped vehicles, DO NOT locate the antenna near the
ABS control unit (or any control unit).
* Disconnect all on-board computers, when using electric
welding equipment.
* DO NOT expose the ABS control unit to prolonged periods of
high heat (185
F/85C for 2 hours is generally considered a
maximum limit).


AN TI- T H EFT S YSTE M

1999 D odge P ic ku p R 1500
1999 ACCESSORIES & EQUIPMENT
CHRY - Anti-Theft Systems
Ram Pickup, Ram Van & Ram Wagon
DESCRIPTION
The Vehicle Theft Security System (VTSS) provides an engine
no-run feature, flashes headlights and sounds horn if any door or hood
is opened without using key or remote keyless entry transmitter, or if
battery cables are disconnected then reconnected when system is
activated.
Anti-theft system is controlled by Central Timer Module
(CTM). CTM is located under driver's side of dash panel, right of
steering column. If CTM is faulty, CTM cannot be repaired and must be
replaced.
VTSS is also equipped with a power-up mode. If battery is
disconnected or looses power while VTSS is armed, VTSS system remains
armed when power is restored. A temper alert signal is sounded on
vehicle entry if VTSS was triggered while away from vehicle. Horn will
sound 3 times alerting owner VTSS was triggered.
OPERATION
ARMING PROCEDURE (PASSIVE)
Remove key from ignition. Ensure headlights are off. Lock
doors while open, using power lock switch. Power lock switch will not
operate with key in ignition or headlights on while door is open.
Vehicle Theft Security System (VTSS) will not arm using key in lock
cylinder or mechanical lock button. While system is arming, SECURITY
light will flash rapidly for 15 seconds. Opening any door or turning
the ignition key while light is flashing will abort arming process.
Once arming process is complete, SECURITY light will go out.
ARMING PROCEDURE (ACTIVE)
Pressing Remote Keyless Entry (RKE) transmitter LOCK button
will actively arm Vehicle Theft Security System (VTSS). All doors must\
be closed and ignition switch in OFF position. While system is arming,
SECURITY light will flash rapidly for 15 seconds. Opening any door or
turning the ignition key while light is flashing will abort arming
process. Once arming process is complete, SECURITY light will go out.
DISARMING
Vehicle Theft Security System (VTSS) can be disarmed 2 ways:
unlock vehicle using key in any door and pressing remote keyless entry
transmitter UNLOCK button. If alarm has been set off, either method
can be used to disarm and shut-off horn.
CENTRAL TIMER MODULE (CTM)
Central Timer Module (CTM) is Vehicle Theft Security System
(VTSS) processor. CTM uses the data bus network to allow sharing and
reporting of sensor information. If a door ajar sensor is opened while
VTSS is set, a signal is sent to flash headlights and sound horn. PCM
is also notified through bus network to enable engine no-run feature.