radiator DODGE RAM 1999 Service User Guide
[x] Cancel search | Manufacturer: DODGE, Model Year: 1999, Model line: RAM, Model: DODGE RAM 1999Pages: 1691, PDF Size: 40.34 MB
Page 634 of 1691
FITTINGS. Remove air cleaner, throttle body, drive belts, generator,
fan and fan pulley. Remove lower fan shroud.
CAUTION: When removing engine, DO NOT lift engine by intake manifold.
5) Remove intake manifold. See INTAKE MANIFOLD. Raise and
support vehicle. Remove starter. Remove exhaust pipe and heat shields.
Disconnect transmission shift linkage. Remove crank sensor.
6) On A/T models, remove transmission inspection cover. Mark
torque converter-to-flexplate position for installation reference.
Remove torque converter-to-flexplate bolts. On M/T models, disconnect
clutch release mechanism at clutch housing.
7) Attach engine hoist to cylinder heads (at intake manifold
flanges). On all models, support transmission using a floor jack.
Remove transmission or clutch housing-to-cylinder block bolts. Remove
engine mount bolts. Remove engine out front of vehicle.
Installation
To install, reverse removal procedure. Tighten bolts/nuts to
specification. See TORQUE SPECIFICATIONS table. On A/T models, ensure
reference marks on torque converter and flexplate are aligned.
Evacuate and charge A/C system.
Removal ( Dakota 2WD, Durango 2WD, Grand Cherokee & Ram
Pickup)
1) Release fuel pressure. See FUEL PRESSURE RELEASE.
Disconnect and remove battery. On all except Pickup, scribe hood
hinges for installation reference and remove hood.
2) On all models, drain cooling system. Disconnect coolant
hoses. Remove radiator, fan and shroud. Discharge A/C system (if
equipped) using approved refrigerant recovery/recycling equipment.
Disconnect A/C lines, and plug openings. On Pickup, remove upper core
support, transmission cooler and A/C condenser. On all models, remove
belt, air cleaner, vacuum lines, distributor cap and wiring.
3) Disconnect necessary electrical wiring. Disconnect fuel
lines. See FUEL LINE DISCONNECT FITTINGS. Remove throttle body and
linkage. Remove intake manifold. Remove starter, generator, charcoal
canister and horns. Disconnect power steering hoses (if equipped).
Raise and support vehicle. Drain oil. Disconnect exhaust pipe at
exhaust manifold.
4) On A/T models, remove transmission housing inspection
plate. Mark torque converter-to-flexplate position for installation
reference. Remove torque converter-to-flexplate bolts. Remove bracket
for transmission cooler lines.
NOTE: It may be necessary to remove manual transmission if
transmission cannot be supported using floor jack.
5) On M/T models, disconnect clutch release mechanism at
clutch housing. On all models, support transmission using a floor
jack. Remove transmission or clutch housing-to-cylinder block bolts.
Install engine lifting fixture, and attach chain.
CAUTION: When removing engine, DO NOT lift engine by intake manifold.
6) On Ram Pickup and Grand Cherokee, remove front engine
mount bolts. Remove engine from vehicle. On Dakota 2WD and Durango 2WD
models, remove front engine mount through-bolts. See Fig. 3. Remove
engine from vehicle.
Installation
To install, reverse removal procedure. Tighten bolts/nuts to
specification. See TORQUE SPECIFICATIONS table. On A/T models, ensure
Page 635 of 1691
reference marks on torque converter and flexplate are aligned.
Evacuate and charge A/C system.
Removal (Durango 4WD & Dakota 4WD)
1) Release fuel pressure. See FUEL PRESSURE RELEASE.
Disconnect and remove battery. Scribe hood hinges for installation
reference and remove hood.
2) Drain cooling system. Disconnect coolant hoses. Remove
radiator, fan and shroud. Discharge A/C system (if equipped) using
approved refrigerant recovery/recycling equipment. Disconnect A/C
lines, and plug openings. Remove air cleaner, vacuum lines,
distributor cap and wiring.
3) Disconnect necessary electrical wiring. Disconnect fuel
lines. See FUEL LINE DISCONNECT FITTINGS. Disconnect accelerator
linkage. Remove throttle body. Remove starter and generator.
Disconnect power steering hoses. Raise and support vehicle. Drain oil.
Disconnect exhaust pipe at exhaust manifold.
NOTE: Engine, transmission and front axle are connected and
supported with insulators and brackets. See Fig. 3.
4) On left side, remove 2 bolts attaching differential pinion
nose bracket-to-bellhousing bolts. Remove pinion nose bracket-to-
adapter bolts (located on top of differential, near pinion). Separate
engine from engine mount by removing engine mount through-bolt and nut
located on top of engine mount.
5) On right side, remove 2 axle-to-bracket bolts and bracket-
to-bellhousing bolt. Separate engine from engine mount by removing
engine mount through-bolt and nut located on top of engine mount.
Remove engine from vehicle.
Page 647 of 1691
CAUTION: After removing fan clutch assembly, DO NOT store fan clutch
with rear of shaft pointing downward. Silicone fluid from fan
clutch may drain into fan drive bearing, causing lubricant
failure.
Removal
1) Disconnect negative battery cable. Drain cooling system.
Remove throttle cable at top of fan shroud. Unsnap coolant overflow
tank from fan shroud and lay aside. DO NOT disconnect coolant hose.
2) Remove upper radiator hose. Using Fan Wrench (SP346) from\
Set (2017DSP), remove fan clutch assembly from water pump by turning
nut counterclockwise as viewed from front. DO NOT remove fan clutch
assembly at this time.
3) Remove fan shroud bolts and clips. Remove fan shroud and
fan clutch assembly as a unit. Locate accessory drive belt tensioner,
and rotate tensioner clockwise (counterclockwise on heavy-duty cycle
engines) to release tension on accessory drive belt.
4) Note drive belt routing for installation reference. Belt
must be correctly routed during installation, or engine will overheat
due to water pump rotating in wrong direction.
5) Remove bolts and water pump pulley. Disconnect lower
radiator hose and heater hoses. Remove coolant return tube from water
pump. Remove bolts, water pump and gasket.
Installation
To install, reverse removal procedure using NEW gasket.
Tighten bolts to specification. See TORQUE SPECIFICATIONS table. Fill
system with coolant. Ensure accessory drive belt is installed in
original direction to ensure proper rotation of water pump. See
Fig. 12 .
Fig. 12: Drive Belt Routing (Except 5.9L - Heavy Duty Cycle)
Courtesy of Chrysler Corp.
Page 706 of 1691
FUEL TANKS
GAS CAPS
GASKETS
GROMMETS (VALVE COVER)
HARMONIC DAMPERS
HEATER CONTROL VALVES
HEATER CORES
HOSE AND TUBE COUPLERS, CONNECTORS AND CLAMPS
HOSE CLAMPS
HOSE CONNECTORS
HOSE COUPLERS
HOSES AND TUBES (FUEL LINES, RADIATOR, VACUUM, BY PASS,
HEATER, RECOVERY TANK AND OIL COOLERS)
HOUSINGS
IDLE AIR CONTROLS
IDLE SPEED CONTROL ACTUATORS
IGNITION BOOTS
IGNITION COIL TOWERS
IGNITION COILS
IGNITION CONTROL MODULES (ICM)
IGNITION SWITCHES
IGNITION TERMINALS
IGNITION WIRES, BOOTS, COIL TOWERS AND TERMINALS (SECONDARY)
IN-TANK FUEL STRAINERS
INERTIA FUEL SHUT-OFF SWITCHES
INTAKE AIR TEMPERATURE SENSORS
INTAKE MANIFOLDS
INTERCOOLERS
KNOCK SENSORS
LIQUID VAPOR SEPARATORS
MANIFOLD ABSOLUTE PRESSURE (MAP) SENSORS
MASS AIR FLOW (MAF) SENSORS
METAL AIR MANIFOLDS AND PIPES
METAL AIR PIPES
MIX CONTROL SOLENOIDS
MOTOR MOUNTS
O-RINGS, GASKETS, SEALS AND SPRING LOCKS
O2 SENSORS
OIL PRESSURE SENDING UNITS
OIL PUMP PICK-UP SCREENS
OIL PUMPS
PARK NEUTRAL POSITION SWITCHES
PCV BREATHER ELEMENTS
PCV ORIFICES
PCV VALVES
PICK-UP ASSEMBLIES (INCLUDES MAGNETIC, HALL EFFECT AND
OPTICAL)
POWER STEERING PRESSURE SENSORS
POWERTRAIN CONTROL MODULES (PCM) AND PROM
POWERTRAIN CONTROL PROM
PRESSURIZED EXPANSION TANK CAPS
RADIATOR CAPS AND PRESSURIZED EXPANSION TANK CAPS
RADIATOR FAN BLADES
RADIATOR FAN CLUTCHES
RADIATORS
ROLL OVER VALVES
SEALING COMPOUNDS
SEALS
SECONDARY AIR INJECTION SYSTEM MANAGEMENT DEVICES
SENSORS AND ACTUATORS
SHROUDS, BAFFLES AND DEFLECTORS
SPARK PLUGS
SPRING LOCKS
Page 763 of 1691
affecting performance .. A .. Require repair or replacement.
Leaking ................. A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
\
\
\
\
\
\
\
HOSE AND TUBE COUPLERS, CONNECTORS AND CLAMPS
NOTE: When replacing fuel lines and hoses, replace with product
that meets or exceeds OEM design specifications.
HOSE AND TUBE COUPLER, CONNECTOR AND CLAMP INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Application incorrect ... B ............ Require replacement.
Connected incorrectly ... A ................. Require repair.
Corroded, not reusable .. 1 ............ Suggest replacement.
Cracked ................. A ............ Require replacement.
Insufficient clamping
force, allowing hose to
leak ................... A .. Require repair or replacement.
Leaking ................. A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Safety clip missing (not
leaking) ............... C ... Require replacement of safety
clip.
Stripped ................ A ............ Require replacement.
\
\
\
\
\
\
\
HOSE CLAMPS
See HOSE AND TUBE COUPLERS, CONNECTORS AND CLAMPS .
HOSE CONNECTORS
See HOSE AND TUBE COUPLERS, CONNECTORS AND CLAMPS .
HOSE COUPLERS
See HOSE AND TUBE COUPLERS, CONNECTORS AND CLAMPS .
HOSES AND TUBES (FUEL LINES, RADIATOR, VACUUM, BY PASS,
HEATER, RECOVERY TANK AND OIL COOLERS)
HOSE AND TUBE (FUEL LINE, RADIATOR, VACUUM, BY PASS, HEATER,
RECOVERY TANK AND OIL COOLER) INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Application incorrect ... B ............ Require replacement.
Connected incorrectly ... A ................. Require repair.
Corroded, not reusable .. 1 ............ Suggest replacement.
Cracked ................. A ............ Require replacement.
Dry-rotted .............. 1 .. Suggest repair or replacement.
Hard .................... 1 .. Suggest repair or replacement.
Inner fabric (webbing)
damaged ................ A ............ Require replacement.
Insufficient clamping
force, allowing hose to
leak ................... A .. Require repair or replacement.
Leaking ................. A .. Require repair or replacement.
Maintenance intervals ... 3 ............ Suggest replacement.
Page 785 of 1691
Terminal burned, affecting
performance ............ A ........... (2) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Wire lead conductors
exposed ................ B .. Require repair or replacement.
Wire lead corroded ...... A .. Require repair or replacement.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
( 1) - Refer to manufacturer's diagnostic trouble code
procedure and require repair or replacement of affected
component(s).
( 2) - Determine cause and correct prior to repair or
replacement of part.
( 3) - Determine source of contamination, such as engine coolant,
fuel, metal particles, or water. Require repair or
replacement.
( 4) - Includes inoperative, intermittent operation, failure to
perform all functions, or out of OEM specification.
\
\
\
\
\
\
\
POWERTRAIN CONTROL PROM
See POWERTRAIN CONTROL MODULES (PCM) AND PROM .
PRESSURIZED EXPANSION TANK CAPS
See RADIATOR CAPS AND PRESSURIZED EXPANSION TANK CAPS .
RADIATOR CAPS AND PRESSURIZED EXPANSION TANK CAPS
RADIATOR CAP AND PRESSURIZED EXPANSION TANK CAP INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Application incorrect ... B ........... Require replacement.
Coolant recovery check
valve inoperative ...... A ....... ( 1) Require replacement.
Fails to maintain proper
pressure ............... B ........... Require replacement.
Gasket missing .......... C . Require replacement of gasket.
Missing ................. C ........... Require replacement.
Seal missing ............ C ... Require replacement of seal.
( 1) - Inoperative includes intermittent operation or out of
OEM specification.
\
\
\
\
\
\
\
RADIATOR FAN BLADES
Page 786 of 1691
![DODGE RAM 1999 Service User Guide RADIATOR FAN BLADE INSPECTION \
\
\
\
\
\
\
Condition C](/img/12/56915/w960_56915-785.png "DODGE RAM 1999 Service User Guide RADIATOR FAN BLADE INSPECTION \
\
\
\
\
\
\
Condition C")
RADIATOR FAN BLADE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Application incorrect ... B ........... Require replacement.
Attaching hardware
broken ................. A .. Require repair or replacement
of hardware.
Attaching hardware
missing ................ C ......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A .. Require repair or replacement
of hardware.
Bent .................... A ........... Require replacement.
Broken .................. A ........... Require replacement.
Cracked ................. A ........... Require replacement.
Loose ................... A . Require repair or replacement.
Missing ................. C ........... Require replacement.
\
\
\
\
\
\
\
RADIATOR FAN CLUTCHES
NOTE: Some lateral movement, measured at the fan blade tip,
may be normal.
RADIATOR FAN CLUTCH INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Bearing noisy ........... A ............ Require replacement.
Bearing worn ............ A ............ Require replacement.
Fastener loose .......... A ... Require repair or replacement
of fastener.
Inoperative ............. A ........ ( 1) Require replacement.
Leaking ................. 1 ............ Suggest replacement.
Seized .................. A ............ Require replacement.
Slips (insufficient fan
speed) ................. A ............ Require replacement.
Thermal control
incorrect .............. B .. Require repair or replacement.
( 1) - Inoperative includes intermittent operation or out of
OEM specification.
\
\
\
\
\
\
\
RADIATORS
RADIATOR INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Air flow restriction .... A ................. Require repair.
Page 801 of 1691
![DODGE RAM 1999 Service User Guide check for accepted cleaning procedure. \
\
\
\
\
\
\
TUB](/img/12/56915/w960_56915-800.png "DODGE RAM 1999 Service User Guide check for accepted cleaning procedure. \
\
\
\
\
\
\
TUB")
check for accepted cleaning procedure. \
\
\
\
\
\
\
TUBE CLAMPS
See HOSE AND TUBE COUPLERS, CONNECTORS AND CLAMPS .
TUBE CONNECTORS
See HOSE AND TUBE COUPLERS, CONNECTORS AND CLAMPS .
TUBE COUPLERS
See HOSE AND TUBE COUPLERS, CONNECTORS AND CLAMPS .
TUBES
See HOSES AND TUBES (FUEL LINES , RADIATOR, BY PASS, HEATER,
RECOVERY TANK AND OIL COOLERS).
TURBO CHARGERS
TURBO CHARGER INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Boost pressure
incorrect .............. A ........... ( 1) Require repair or
replacement.
Leaking ................. A .. Require repair or replacement.
Noisy ................... 2 .. Suggest repair or replacement.
Oil seal (internal)
leaking ................ A .. Require repair or replacement.
Vibrates ................ A .. Require repair or replacement.
( 1) - Boost pressure problems may be caused by other systems
or components.
\
\
\
\
\
\
\
VACUUM CONNECTIONS
See VACUUM HOSES, TUBES AND CONNECTIONS (NON-METALLIC) .
VACUUM HOSES, TUBES AND CONNECTIONS (NON-METALLIC)
VACUUM HOSE, TUBE AND CONNECTION (NON-METALLIC) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Leaking ................. A .. Require repair or replacement.
Melted .................. A ............ Require replacement.
Missing ................. C ............ Require replacement.
Oil-soaked (spongy) ..... 1 ............ Suggest replacement.
Page 820 of 1691
GEN ER AL C O OLIN G S YSTE M S ER VIC IN G
1999 D odge P ic ku p R 1500
GENERAL INFORMATION
General Cooling System Servicing
* PLEASE READ THIS FIRST *
The following article is for general information only.
Information may not apply to all years, makes and models. See specific
article in the ENGINE COOLING section.
DESCRIPTION
The basic liquid cooling system consists of a radiator, water
pump, thermostat, electric or belt-driven cooling fan, pressure cap,
heater, and various connecting hoses and cooling passages in the block
and cylinder head.
MAINTENANCE
DRAINING
Remove radiator cap and open heater control valve to maximum
heat position. Open drain cocks or remove plugs in bottom of radiator
and engine block. In-line engines usually have one plug or drain cock,
while "V" type engines will have 2, one in each bank of cylinders.
CLEANING
A good cleaning compound removes most rust and scale. Follow
manufacturer's instructions in the use of cleaner. If considerable
rust and scale has to be removed, cooling system should be flushed.
Clean radiator air passages with compressed air.
FLUSHING
CAUTION: Some manufacturers use an aluminum and plastic radiator.
Flushing solution must be compatible with aluminum.
Back Flushing
Back flushing is an effective means of removing cooling
system rust and scale. The radiator, engine and heater core should be
flushed separately.
Radiator
To flush radiator, connect flushing gun to water outlet of
radiator and disconnect water inlet hose. To prevent flooding engine,
use a hose connected to radiator inlet. Use air in short bursts to
prevent damage to radiator. Continue flushing until water runs clear.
Engine
To flush engine, remove thermostat and replace housing.
Connect flushing gun to water outlet of engine. Flush using short air
bursts until water runs clean.
Heater Core
Flush heater core as described for radiator. Ensure heater
control valve is set to maximum heat position before flushing heater.
Page 821 of 1691
REFILLING
To prevent air from being trapped in engine block, engine
should be running when refilling cooling system. After system is full,
continue running engine until thermostat is open, then recheck fill
level. Do not overfill system.
TESTING
THERMOSTAT
1) Visually inspect thermostat for corrosion and proper
sealing of valve and seat. If okay, suspend thermostat and thermometer
in a 50/50 mixture of coolant and water. See Fig. 1. Do not allow
thermostat or thermometer to touch bottom of container. Heat water
until thermostat just begins to open.
2) Read temperature on thermometer. This is the initial
opening temperature and should be within specification. Continue
heating water until thermostat is fully open and note temperature.
This is the fully opened temperature. If either reading is not to
specification, replace thermostat.
Fig. 1: Testing Thermostat in Anti-Freeze/Water Solution
PRESSURE TESTING
A pressure tester is used to check both radiator cap and