ECU DODGE RAM 1999 Service Owner's Guide
[x] Cancel search | Manufacturer: DODGE, Model Year: 1999, Model line: RAM, Model: DODGE RAM 1999Pages: 1691, PDF Size: 40.34 MB
Page 363 of 1691
being replaced, remove booster check valve and seal.
Installation
1) If new booster is being installed, install check valve and
seal. Position booster on dash, and install lock nuts on booster
mounting studs finger tight. Install booster push rod on brake pedal
pin, and secure rod with NEW retaining clip.
2) Tighten booster lock nuts to specification. Install master
cylinder on booster, and tighten mounting nuts to specification. See
TORQUE SPECIFICATIONS table. Connect vacuum hose to booster check
valve. Start vehicle and check booster operation.
COMBINATION VALVE
Removal & Installation
Raise and support vehicle. Mark brakelines for assembly
reference. Disconnect parking brake cable from clip on valve, if
necessary. Disconnect brake warning light connection at switch.
Disconnect all brake hydraulic lines at valve. Cap brakelines to
prevent dirt from entering system. Remove valve. To install, reverse
removal procedures. Bleed brake system. See BLEEDING PROCEDURES under
BLEEDING BRAKE SYSTEM.
AXLE BEARING & SEAL (FULL FLOATING AXLE)
Removal & Installation (Ram Pickup With 12" & 13" Drums)
1) Raise and support vehicle. Remove wheel. Remove axle shaft
nuts and washers. Strike center of axle flange to free cones. Remove
axle shaft and gasket.
2) Straighten and remove nut lock. Remove adjustment nut and
outer bearing. Remove drum assembly. Remove seal and inner bearing
from drum assembly.
3) Pack inner bearing, and install inner bearing and seal in
drum. Install drum assembly, outer bearing and adjustment nut. While
rotating drum, tighten adjustment nut to specification. See TORQUE
SPECIFICATIONS table.
4) Back off adjustment nut 1/8 turn to obtain .001-.010" (0.
025-0.254 mm) end play. Bend nut lock into spindle keyway. Install
gasket and axle shaft. Install wheel, and lower vehicle. See TORQUE
SPECIFICATIONS table.
OVERHAUL
NOTE: Use illustrations when overhauling components. See
Figs. 2-6.
DISC BRAKE SPECIFICATIONS
DISC BRAKE SPECIFICATIONS \
\
\
\
\
\
\
Application In. (mm)\
Disc Diameter
Dakota ............................................... 11.30 (287)\
Ram Pickup
1/2 Ton ............................................. 11.57 (294)\
3/4 & 1 Ton ......................................... 12.50 (318)\
Ram Van
1/2 & 3/4 Ton ....................................... 11.75 (299)\
1 Ton ............................................... 12.82 (326)\
Lateral Runout
Page 367 of 1691
CLU TC H
1999 D odge P ic ku p R 1500
1998-99 CLUTCHES
CHRY - RWD - Trucks
Dakota, Ram Pickup
DESCRIPTION
Clutches on all models are dry, single-disc design.
Adjustment for wear is not possible. Clutch pedal is connected to
release fork through a hydraulic master cylinder and slave cylinder
and is not adjustable. Pre-lubricated clutch bearing is constant
running type. External adjustments cannot be made.
All models are equipped with a clutch pedal position switch.
The switch completes the circuit to the starter relay and is mounted
on clutch master cylinder push rod. The position switch is an integral
part of clutch master cylinder push rod and cannot be serviced
separately.
TRANSMISSION/TRANSFER CASE APPLICATION
\
\
\
\
\
\
\
Transmission Transfer Case
Dakota
AX15, NV1500 & NV3500 .............................. NV231 & NV242
Ram Pickup
NV3500, NV4500, NV4500HD & NV5600 ..... NV231HD, NV241LD & NV241HD
\
\
\
\
\
\
\
ADJUSTMENTS
CLUTCH PEDAL FREE PLAY
NOTE: Clutches are a single, dry disc type. Adjustment for wear is
not possible. Clutch is actuated through hydraulic master
cylinder and slave cylinder, and is self-adjusting.
SHIFT LINKAGE ADJUSTMENT
NV231 (Dakota)
1) Shift transfer case into 4H position, and secure shift
lever in shift gate. See Fig. 1. Raise and support vehicle. Loosen
shift rod lock bolt at swivel. Ensure shift rod slides freely in
adjusting swivel.
2) Ensure transfer case range lever is in 4H position. Slide
adjusting swivel forward until shift rod contacts shift gate
crossover, then slide adjusting swivel back, allowing a .11-.20" (3-5
mm) gap between shift lever and shift gate.
3) Center pin on adjusting swivel in shift arm and tighten
lock bolt to 90 INCH lbs. (10 N.m.). Lower vehicle, making sure all
wheels are off floor. Start engine. Shift transfer case through all
ranges to verify correct adjustment.
NV231HD, NV241LD & NV241HD (Ram Pickup)
1) Place shift lever into 2H position. Raise and support
vehicle. Loosen shift rod lock bolt at swivel. See Fig. 2. Ensure
shift rod fits in swivel and does not bind.
2) Ensure transfer case shift lever is in 2H position. Lower
vehicle. Position shift lever in cab so distance between instrument
Page 368 of 1691
panel and 2H position dot in shift lever insert is 5.75" (14.6 cm).
Make measurement parallel to floor of vehicle.
3) Tighten shift rod lock bolt to 90 INCH lbs. (10 N.m).
Start engine. Shift transfer case through all ranges to verify proper
operation.
NV242 (Dakota)
1) Put shift lever into 4FT position and secure. Raise
vehicle. Loosen shift rod lock bolt at swivel. See Fig. 1. Ensure
shift rod slides freely in adjusting swivel.
2) Ensure transfer case shift lever is in 4FT position. Slide
adjusting swivel forward until shift lever contacts shifter gate
crossover then slide adjusting swivel back, allowing a 0.11-0.20" (3-5
mm) gap between shift lever and shift gate.
3) Center pin on adjusting swivel in shift arm and tighten
lock bolt to 90 INCH lbs. (10 N.m). Lower vehicle, making sure wheels
are off floor. Start engine. Shift transfer case through all ranges to
verify correct adjustment.
Fig. 1: Adjusting Transfer Case Shift Linkage (Dakota)
Courtesy of Chrysler Corp.
Page 374 of 1691
Removal (AX15 & NV1500)
1) Shift gear selector into 1st or 3rd gear. Raise and
support vehicle. Disconnect necessary exhaust system components.
Remove "Y" pipe and position remaining pipes for working clearance.
Support transmission adjustable jackstand. Disconnect rear cushion and
mounting bracket from transmission or transfer case.
2) Remove rear crossmember. If transmission will be
disassembled for repair, drain transmission fluid. Disconnect
transmission shift linkage, speedometer cable, transfer case vacuum
lines and clutch hydraulic lines. Lower transmission/transfer case
assembly no more than 3" (76 mm). Reaching around transmission case,
unseat and lift shift lever dust boot. Press shift lever retainer
downward, turn retainer counterclockwise, and lift lever and retainer
out of shift tower.
3) Mark front and rear drive shaft and "U" joint for
reassembly reference. Disconnect and remove both drive shafts. Remove
crankshaft position sensor (AX15). Disconnect transmission/transfer
case assembly vent hoses. Remove slave cylinder from clutch housing.
Remove wire harness from clips on transmission case and transfer case.
4) Support transmission/transfer case assembly with
transmission jack. Secure assembly to jack with safety chains.
Reposition adjustable jackstand under engine. Remove clutch housing
brace rod. Remove clutch housing nuts and bolts. Remove
transmission/transfer case assembly.
Installation
To install, reverse removal procedure. Apply high-temperature
grease to release fork, lever, pivot ball stud and pilot bushing
located in end of crankshaft. Fill transmission with appropriate
fluid, if necessary. Tighten all nuts and bolts to specification. See
TORQUE SPECIFICATIONS table.
Removal (NV 3500)
1) Disconnect negative battery cable. Shift transmission to
Neutral. Open console lid and remove bolts attaching console to floor
pan. Lift cup holder bin and remove bolt attaching console to floor
pan. Lift rear of console and pull console rearward to separate from
shift bezel. Remove console from vehicle. Remove screws attaching
shift boot to floor pan and slide boot upward on lever extension.
2) Remove shift lever extension. Raise and support vehicle.
On 4WD models, remove skid plate, if equipped. Mark drive shaft and
axle yoke for alignment reference. Remove drive shaft. Remove exhaust
"Y" pipe. On 4WD models, disconnect and lower remaining exhaust pipes
for clearance as necessary. Disconnect speed sensor harness connector
and back-up light harness connector.
3) Support engine using adjustable jackstand. If transmission
is to be disassembled for repair, drain lubricant from transmission.
On 4WD models, disconnect transfer case shift linkage at transfer case
range lever and remove shift lever from transmission. Remove
bolts/nuts attaching transmission to rear mount.
4) Support transmission with a transmission jack. Secure
transmission with safety chains. Remove rear crossmember. On 4WD
models, support transfer case with transmission jack and secure
transfer case to jack with safety chains. Remove transfer case
attaching nuts and move transfer case rearward until input gear clears
transmission output shaft.
5) Lower transfer case assembly and remove it from under
vehicle. On 4WD models, remove clutch slave cylinder splash shield, if
equipped. Remove clutch slave cylinder and move aside for working
clearance. Remove starter. Remove transmission splash shield. Remove
transmission harness wires from clips on transmission shift cover.
6) Lower transmission slightly. Remove shift tower and lever
assembly. Remove transmission-to-engine attaching bolts. Slide
Page 375 of 1691
transmission and jack rearward until input shaft clears clutch disc.
Lower transmission jack and remove transmission from under vehicle.
Installation
1) To install, reverse removal procedure. Apply high-
temperature grease to pilot bushing located in end of crankshaft. Also
apply grease to release bearing bore, release fork, release fork ball
stud and drive shaft slip yoke. Apply sealer to threads of drain plug
before installing in case.
2) Align reference marks made on drive shaft(s) and "U"
joints during removal. After installing clutch assembly and housing,
tighten housing bolts nearest alignment dowels first. During final
transmission installation, install shims between clutch housing and
transmission at appropriate bolt location. Tighten all nuts and bolts
to specification. See TORQUE SPECIFICATIONS table.
TRANSMISSION (RAM PICKUP)
Removal (NV3500 & NV5600)
1) Disconnect negative battery cable. Shift transmission to
Neutral. Remove shift boot bezel screws and slide boot upward on lever
extension. Remove shift tower and lever assembly. Raise and support
vehicle.
2) On 4WD models, remove skid plate, if equipped. Remove
crankshaft position sensor. Mark drive shaft and axle yoke for
alignment reference. Remove drive shaft. Remove exhaust "Y" pipe. On
4WD models, disconnect and lower remaining exhaust pipes for
clearance, as necessary. Disconnect speed sensor harness connector.
3) Support engine using adjustable jackstand. If transmission
is to be disassembled for repair, drain lubricant from transmission.
On 4WD models, disconnect transfer case shift linkage at transfer case
range lever and remove shift lever from transmission. Remove
bolts/nuts attaching transmission to rear mount.
4) Support transmission with a transmission jack. Secure
transmission with safety chains. Remove rear crossmember. On 4WD
models, support transfer case with transmission jack and secure
transfer case to jack with safety chains. Remove transfer case
attaching nuts and move transfer case rearward until input gear clears
transmission output shaft.
5) Lower transfer case assembly and remove it from under
vehicle. On 4WD models, remove clutch slave cylinder splash shield, if
equipped. Remove clutch slave cylinder and move aside for working
clearance. Remove starter. Remove transmission splash shield. Remove
transmission harness wires from clips on transmission shift cover. On
some models, it may be necessary to remove front axle struts and oil
filter for access and removal clearance.
6) Lower transmission slightly. Remove shift tower and lever
assembly. Remove transmission-to-engine bolts. Slide transmission and
jack rearward until input shaft clears clutch disc. Lower transmission
jack and remove transmission from under vehicle.
Installation
1) To install, reverse removal procedure. Apply high-
temperature grease to pilot bushing located in end of crankshaft. Also
apply grease to release bearing bore, release fork, release fork ball
stud and drive shaft slip yoke.
2) Apply sealer to threads of drain plug before installing in
case. Align reference marks made on drive shaft(s) and axle yoke(s)
during removal. After installing clutch assembly and housing, tighten
housing bolts nearest alignment dowels first. Tighten all nuts and
bolts to specification. See TORQUE SPECIFICATIONS table.
Removal (NV4500 & NV4500HD)
Page 376 of 1691
1) Disconnect negative battery cable. Shift transmission to
Neutral. Remove shift boot bezel screws and slide boot upward on lever
extension. Scribe mark position of extension on shank of shift lever.
2) Raise and support vehicle. On 4WD models, remove skid
plate, if equipped. Mark drive shaft and axle yoke for alignment
reference. Remove drive shaft. Remove exhaust "Y" pipe. On 4WD models,
disconnect and lower remaining exhaust pipes for clearance as
necessary. Disconnect speed sensor harness connector and back-up light
harness connector.
3) Support engine using adjustable jackstand. If transmission
is to be disassembled for repair, drain lubricant from transmission.
See Fig. 9 . On 4WD models, disconnect transfer case shift linkage at
transfer case range lever and remove shift lever from transmission.
Remove bolts/nuts attaching transmission to rear mount.
4) Support transmission with a transmission jack. Secure
transmission with safety chains. Remove rear crossmember. On 4WD
models, support transfer case with transmission jack and secure
transfer case to jack with safety chains. Remove transfer case
attaching nuts and move transfer case rearward until input gear clears
transmission output shaft.
5) Lower transfer case assembly and move it from under
vehicle. On 4WD models, remove clutch slave cylinder splash shield, if
equipped. Remove clutch slave cylinder, and move aside. Remove
starter. Remove transmission splash shield. Remove transmission
harness wires from clips on transmission shift cover. On some models,
it may be necessary to remove front axle struts and oil filter for
access and removal clearance.
6) Lower transmission slightly. Remove shift tower and lever
assembly. Remove transmission-to-engine bolts. Slide transmission and
jack rearward until input shaft clears clutch disc. Lower transmission
jack and remove transmission from under vehicle.
Installation
1) To install, reverse removal procedure. Apply high-
temperature grease to pilot bushing located in end of crankshaft. Also
apply grease to release bearing bore, release fork, release fork ball
stud and propeller shift slip yoke.
2) Apply sealer to threads of drain plug before installing in
case. Align reference marks made on drive shaft(s) and axle yoke(s)
during removal. After installing clutch assembly and housing, tighten
housing bolts nearest alignment dowels first.
3) During final transmission installation, install shims
between clutch housing and transmission at appropriate bolt location.
See CLUTCH HOUSING BORE RUNOUT and CLUTCH HOUSING FACE RUNOUT under
CLUTCH HOUSING (RAM PICKUP) under TESTING. Press extension to scribe
mark made during removal. A 0.12-0.20" (3-5 mm) space should exist
between shift lever isolator, top edge of stub shaft and tool lower
jaw. Tighten all nuts and bolts to specification. See TORQUE
SPECIFICATIONS table.
Fig. 9: Identifying Transmission Drain Bolt (NV4500 & NV4500HD)
Courtesy of Chrysler Corp.
CLUTCH ASSEMBLY
Page 378 of 1691
NOTE: Clutch release bearing is packed with grease. DO NOT use
cleaning solvent to clean release bearing.
Removal
1) Remove transmission and clutch housing. See TRANSMISSION
(DAKOTA) or TRANSMISSION (RAM PICKUP). Disconnect release bearing fr\
om
fork, and remove bearing. See Fig. 11. Remove release fork.
2) Inspect bearing. Bearing should turn smoothly under a
light thrust load. Inspect release fork and fork ball pivot for
distortion and wear.
Installation
1) Lubricate crankshaft pilot bearing, input shaft splines,
bearing retainer slide surface, fork pivot and release fork pivot
surface with high-temperature bearing grease.
2) Install release fork and release bearing. Ensure fork and
bearing are properly secured. Install transmission and clutch housing.
Fig. 11: Exploded View Of RWD Clutch Release Bearing Assembly
Courtesy of Chrysler Corp.
CLUTCH MASTER CYLINDER
Removal
1) Disconnect clutch pedal interlock switch wires. Remove
locating clip from clutch master cylinder mounting bracket. Remove
retaining clip, flat washer and wave washer that attach clutch master
cylinder push rod to clutch pedal. Slide clutch master cylinder push
rod off pedal pin. Ensure cap on clutch master cylinder reservoir is
tight.
2) Remove clutch fluid reservoir. Rotate clutch master
cylinder 45 degrees counterclockwise to unlock it. Remove cylinder
from dash panel. Remove clutch master cylinder rubber seal from dash
panel.
Installation
Lubricate cylinder seal with liquid soap to ease
installation. Seat seal in dash and around cylinder. To install,
reverse removal procedure.
Page 381 of 1691
![DODGE RAM 1999 Service Owners Guide DTCs from ABS and SRS modules.
Updating Secret Key Data
Connect scan tool to Data Link Connector (DLC) below drivers\
side of instrument panel. Go to ENGINE, then MISC menu on scan](/img/12/56915/w960_56915-380.png "DODGE RAM 1999 Service Owners Guide DTCs from ABS and SRS modules.
Updating Secret Key Data
Connect scan tool to Data Link Connector (DLC) below drivers\
side of instrument panel. Go to ENGINE, then MISC menu on scan")
DTCs from ABS and SRS modules.
Updating Secret Key Data
Connect scan tool to Data Link Connector (DLC) below driver's\
side of instrument panel. Go to ENGINE, then MISC menu on scan tool.
Place the SKIM in SECURED ACCESS MODE by using the appropriate
Personal Identification Number (PIN) for this vehicle. PIN may be
obtained from the owner, vehicle's invoice, or from the manufacturer.
Select UPDATE THE SECRET KEY DATA. The data will be transferred from
Smart Key Immobilizer Module (SKIM) to the PCM.
NOTE: If 3 attempts are made to enter the SECURED ACCESS MODE using
the incorrect Personal Identification Number (PIN), the
SECURED ACCESS MODE will be locked out for one hour. To exit
this locked-out mode, leave ignition switch in the ON
position for one hour with all accessories turned off. It may
be necessary to monitor battery state and connect a battery
charger.
FWD CARS & FWD VANS
Transaxle Shift Quality Quick Learn Procedure (All FWD Cars
Except Avenger & Sebring Coupe, & All FWD Vans)
1) Transaxle shift quality quick learn procedure must be
performed to provide proper transaxle operation if any of the
following have been done:
* Vehicle battery was disconnected.
* Transaxle assembly was replaced.
* Transmission Control Module (TCM) was replaced.
* Solenoid assembly was replaced.
* Valve body was reconditioned or replaced.
2) Transaxle shift quality quick learn procedure must be
performed using Chrysler's Diagnostic Readout Box III (DRB-III) scan
tool. Following conditions must be met when performing transaxle shift
quality quick learn procedure:
* Brakes must be applied.
* Engine speed must be greater than 500 RPM.
* Throttle position sensor angle must be less than 3 degrees.
* Shift lever must remain in designated position until prompted
to shift to overdrive.
* Shift lever must remain in overdrive after the shift to
overdrive until scan tool indicates procedure is complete.
* Calculated oil temperature must be within 60-200
F
(16-93 C).
3) Connect scan tool to Data Link Connector (DLC) below
driver's side of instrument panel. For DLC location, see appropriate
SELF-DIAGNOSTICS article in ENGINE PERFORMANCE.
4) Go to TRANSMISSION display on scan tool. Go to
MISCELLANEOUS display on scan tool. Select QUICK LEARN PROCEDURE
display on scan tool. Follow instructions displayed on scan tool to
perform transaxle shift quality quick learn procedure. Remove scan
tool.
Transaxle Shift Quality Quick Learn Procedure (Avenger &
Sebring Coupe)
1) Transaxle shift quality quick learn procedure must be
performed to provide proper transaxle operation after replacing or
overhauling transaxle. After transaxle work is completed, clear any
Diagnostic Trouble Codes (DTCs) as necessary. Connect Chrysler's
Page 384 of 1691
![DODGE RAM 1999 Service Owners Guide COMPONENT LOCATIONS
COMPONENT LOCATIONS \
\
\
\
\
\
\](/img/12/56915/w960_56915-383.png "DODGE RAM 1999 Service Owners Guide COMPONENT LOCATIONS
COMPONENT LOCATIONS \
\
\
\
\
\
\")
COMPONENT LOCATIONS
COMPONENT LOCATIONS \
\
\
\
\
\
\
Component Location
ABS Control Module
Ram Pickup ....................... Left Side Of Engine Compartment
Ram Van/Wagon ...................................... Under Battery
Data Link Connector (DLC) ...... Lower Left Side Of Instrument Panel\
Output Shaft Speed Sensor (OSS) .......... Left Side Of Transmission\
Park/Neutral Position (PNP) Switch ....... Left Side Of Transmission\
Powertrain Control Module (PCM)
Dakota & Durango ............... Right Front Of Engine Compartment
Ram Pickup ............... Right Rear Corner Of Engine Compartment
Ram Van/Wagon ..................... Under Hood Next To Wiper Motor
Vehicle Speed Sensor (VSS) ........ On Transmission Or Transfer Case\
Extension Housing
\
\
\
\
\
\
\
TROUBLE SHOOTING
ROAD TEST
Perform a road test to verify speed control malfunctions.
Ensure speedometer operation is smooth without flutter at all speeds.
Speedometer fluttering may cause surging in speed control system. For
speedometer diagnosis, see appropriate INSTRUMENT PANELS article. If
road test verifies a surge following speed control set and speedometer
operates smoothly, see OVERSHOOT/UNDERSHOOT FOLLOWING SPEED CONTROL
SET.
If road test verifies an inoperative system, and speedometer
operates smoothly, check for:
* Diagnostic Trouble Codes (DTCs). See SELF-DIAGNOSTIC
SYSTEM.
* Misadjusted brake switch. See BRAKE SWITCH under REMOVAL &
INSTALLATION.
* Poor electrical connections at servo.
* Leaking vacuum reservoir, check valve, hoses or connections.
See VACUUM SUPPLY under COMPONENT TESTS.
* Secure attachments of S/C servo cable.
* Smooth operation of throttle linkage.
* Defective PCM or wiring.
* Defective servo. See SPEED CONTROL SERVO under COMPONENT
TESTS.
To verify a speed control electronic malfunction, use scan
tool to check for DTCs. See SELF-DIAGNOSTIC SYSTEM. A speed control
malfunction may occur without setting a FTC. If no DTCs are stored, go
to CHECKING SPEED CONTROL OPERATION under SYSTEM TESTS.
OVERSHOOT/UNDERSHOOT FOLLOWING SPEED CONTROL SET
If operator repeatedly presses and releases set button with
their foot off accelerator (lift foot set) to begin speed control
operation, vehicle may accelerate and exceed desired set speed by 5
MPH and then decelerate to less than desired set speed before
achieving desired set speed.
Speed Control (S/C) has as adaptive strategy that compensates\
for variations in S/C cable lengths. When S/C is set with vehicle
Page 402 of 1691
Fully depress brake pedal and rotate brake switch
counterclockwise approximately 30 degrees. Remove brake switch from
bracket. Depress lock tabs holding brake switch mounting bracket and
separate harness connector from brake switch.
Installation
1) Before installing brake switch, reset adjustable plunger
by pulling on plunger head until plunger reaches end of travel.
Connect harness connector to brake switch. Depress brake pedal and
insert brake switch into keyed hole in mounting bracket. Rotate brake
switch clockwise into locked position.
2) Gently pull back on brake pedal until pedal will go no
further. This causes the brake switch plunger to ratchet backward to
the correct position. No further adjustment is required.
SPEED CONTROL SERVO
Removal (Except Ram Van & Ram Wagon)
1) Disconnect negative battery cable. Disconnect electrical
connector and vacuum hose from servo. Using finger pressure only, push
servo cable connector from throttle body bellcrank pin. DO NOT pull
cable connector perpendicular to bellcrank.
2) Remove 2 servo cable mounting nuts. Pull servo cable
sleeve away from mounting bracket to expose cable retaining clip.
Remove retaining clip. Remove servo.
Removal (Ram Van & Ram Wagon)
1) Disconnect negative battery cable. Remove engine cover.
Remove air cleaner assembly. Using finger pressure only, push servo
cable connector from throttle body bellcrank pin. DO NOT pull cable
connector perpendicular to bellcrank.
2) Remove right headlight assembly. Disconnect vacuum hose
and electrical connector at servo. Remove 2 servo mounting bracket
bolts. Remove 2 servo cable mounting nuts. Pull servo cable sleeve
away from mounting bracket to expose cable retaining clip. Remove
retaining clip. Remove servo.
Installation (All Models)
With throttle in full open position, align hole in speed
control cable sleeve with hole in servo pin. Install retaining clip.
To complete installation, reverse removal procedure. Tighten mounting
bolts/nuts to 75 INCH lbs. (8.5 N.m).
SPEED CONTROL SWITCHES
Removal & Installation
Turn ignition off. Disconnect negative battery cable. Wait 2
minutes for air bag system to discharge reserve voltage. Remove 2
screws holding air bag assembly to steering column. Separate air bag
assembly from steering column and disconnect air bag, horn and speed
control switch connectors. Remove screws securing speed control switch
to air bag assembly. Separate speed control switch from air bag
assembly. To install, reverse removal procedure.
WIRING DIAGRAMS