ECU DODGE RAM 1999 Service User Guide
[x] Cancel search | Manufacturer: DODGE, Model Year: 1999, Model line: RAM, Model: DODGE RAM 1999Pages: 1691, PDF Size: 40.34 MB
Page 108 of 1691
from housing. To install, reverse removal procedure. Install new "O"
rings to A/C fittings. Evacuate and charge A/C system.
Removal & Installation (Durango - Rear Evaporator Core)
1) Disconnect negative battery cable. Discharge A/C system,
using approved refrigerant recovery/recycling equipment. Remove
headliner from passenger compartment of vehicle. Remove sun visors and
sun visor arm supports.
2) Remove coat hooks, overhead assist handle and dome light.
If equipped, remove overhead console. Remove air outlet bezel from
rear A/C-heater assembly. Remove rear blower motor switch. Remove
upper liftgate opening trim. Disengage "A", "B", "C", and "D" pillar
trim as necessary to prevent trim panel interference.
3) Move second and third row seats to cargo position. Move
front seats to full recline position. Remove headliner fasteners.
Carefully bow headliner and remove through lift gate opening.
4) Disconnect "B" pillar drain hoses from "Y" fittings.
Disconnect "B" pillar refrigerant lines and plug or cover all openings
in A/C system. Remove lower A/C-heater assembly cover. Remove screws
securing refrigerant tube and retaining strap to right side of upper
housing cover. Remove evaporator core. To install, reverse removal
procedure. Install new "O" rings to A/C fittings. Evacuate and charge
A/C system.
Removal & Installation (Ram Pickup - Front)
1) Remove and disassemble A/C-heater housing. See
A/C-HEATER ASSEMBLY . Separate halves of A/C-heater housing and remove
top half. Remove evaporator or heater core from housing.
2) To install, reverse removal procedure. Install new "O"
rings to A/C fittings. Evacuate and charge A/C system. Fill cooling
system. On 5.9L diesel engine, engine is equipped with a one-way check
valve. DO NOT run engine while filling cooling system. Fill engine
with engine turned off.
INSTRUMENT PANEL
Removal & Installation (Dakota & Durango)
1) Disconnect negative battery cable. Disable air bag system.
See AIR BAG SYSTEM SAFETY article. Place front wheels in straight-
ahead position. Remove sill trim from both doorways. Remove kick panel
covers from both sides of vehicle. Remove mounting screws for hood
release handle.
2) Remove steering column trim panel and support bracket.
Remove tilt steering column lever (if equipped). Remove upper and
lower shrouds from steering column. Unplug driver's side air bag
module. Loosen multifunction switch wiring harness connector screw and
disconnect from switch. Screw will remain in connector.
3) Disconnect PRNDL cable. Disconnect shift cable from
steering column. Remove steering coupler lock pin. Remove toe plate
retaining screws. Remove steering column mounting bolts and remove
steering column from vehicle.
4) Remove screw from bulkhead wiring harness connector and
disconnect. Disconnect 2 body wiring harness connectors located next
to bulkhead connector. Disconnect 3 wiring harness connectors, from
junction block, located nearest to dash panel. Disconnect brake light
switch connector. Disconnect Rear Wheel Anti-Lock (RWAL) brake module
(if equipped), located near steering column support brackets.
5) Disconnect plastic retainer clip from parking brake
linkage rod, located at back of parking brake release handle. Remove
rod end from parking brake handle. Remove instrument panel center
support bracket. Unplug vacuum harness connector located at left end
of A/C-heater housing. Disconnect Air Bag Control Module (ACM)
connector.
Page 178 of 1691
foot wires to terminals of a 12-volt battery. After air bag module
deploys, let module cool off and allow dust to settle before
approaching.
POST-COLLISION INSPECTION
When a vehicle has been involved in a collision, certain
components of the passive restraint system must be inspected or
replaced. See PASSIVE RESTRAINT SYSTEM INSPECTION article in the
GENERAL INFORMATION section for post-collision inspection information.
REMOVAL & INSTALLATION
* PLEASE READ THIS FIRST *
WARNING: Failure to follow air bag service precautions may
result in air bag deployment and personal injury. See
SERVICE PRECAUTIONS . After component replacement,
ensure proper system operation. See SYSTEM OPERATION CHECK.
CAUTION: When battery is disconnected, vehicle computer and memory
systems may lose memory data. Driveability problems may
exist until computer systems have completed a relearn cycle.
See COMPUTER RELEARN PROCEDURES in GENERAL INFORMATION
before disconnecting battery.
AIR BAG CONTROL MODULE (ACM)
WARNING: ACM contains impact sensor, which enables SRS to activate air
bag. To avoid accidental air bag deployment, DO NOT connect
ACM electrically to system unless it is bolted to vehicle.
Removal
1) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM . Remove bottom
of center console (ACM trim cover).
2) On M/T models, remove center console from floor panel
transmission tunnel. On A/T models, remove screws securing trim cover
to ACM mounting bracket. See Fig. 2. Pull top of trim cover rearward
to release snap clips from instrument panel support bracket.
3) On all models, loosen but do not remove screws on sides
that secure instrument panel support bracket to ACM mounting bracket.
See Fig. 3 .
4) Remove nuts securing support bracket to studs on lower
instrument panel. Disconnect wire harness retainer from hole in
support bracket. Pull top of support bracket away from instrument
panel studs and fold down over ACM until it is laying on floor panel.
Unplug wire harness connector from ACM.
CAUTION: Always replace ACM and ACM mounting bracket as an assembly.
Replacement ACM includes a NEW mounting bracket. DO NOT mount
NEW ACM to old mounting bracket.
5) Remove screws securing mounting bracket to floor panel
transmission tunnel. Remove ACM, mounting bracket and support bracket
as a unit from floor panel.
Installation
To complete installation, reverse removal procedure. Install
ACM with arrow pointing toward front of vehicle. Connect ACM
connectors, ensuring connectors are locked into position. Tighten ACM
Page 180 of 1691
CAUTION: When removing a deployed air bag, wear eye protection, rubber
gloves and a long-sleeve shirt. Powder residue from air bag
deployment may irritate skin and eyes.
CAUTION: Before removing steering wheel, position front wheels in
straight-ahead position and lock steering column by removing
ignition key. Failure to do so could damage clockspring or
cause clockspring to be off-centered. DO NOT hammer on
steering wheel during removal, or collapsible column could be
damaged.
Removal
1) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM . Air bag module
is mounted on face of steering wheel. Ensure wheels are pointed
straight-ahead and steering wheel is locked.
2) Remove air bag module-to-steering wheel screws from back
side of steering wheel. Lift air bag module and disconnect electrical
connectors from rear of module.
Installation
Connect air bag, cruise control and horn harness connectors
to rear of air bag module. Secure module to steering wheel. Tighten
air bag module-to-steering wheel screws to specification. See
TORQUE SPECIFICATIONS . DO NOT connect negative battery cable at this
time. Go to SYSTEM OPERATION CHECK .
PASSENGER-SIDE AIR BAG MODULE
Removal
1) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Open glove box. Holding glove box door, push center of
glove box bin towards front of vehicle. Flex glove box bin far enough
so glove box stops will clear sides of instrument panel opening. Roll
glove box down until stop bumpers are beyond sides of instrument panel
opening. Release bin. Lift bottom of glove box upward to disengage
hinge hooks form hinge pins.
3) Remove 3 screws securing instrument panel glove box
opening upper trim strip to instrument panel glove box opening upper
reinforcement, then remove trim strip. Remove 4 screws that secure 2
plastic support brackets of passenger-side air bag door panel outlet
housing to glove box opening upper reinforcement.
4) Reach through and above glove box opening to access and
disconnect air bag module harness connector. Remove 2 screws securing
passenger-side air bag module front bracket to instrument panel
structural support. Remove 3 screws securing passenger-side air bag
module rear bracket to glove box opening upper reinforcement.
5) Using trim stick, gently pry passenger-side air bag door
(starting at lower left edge) away from instrument panel top cover.
Remove air bag module, air bag door and panel outlet housing and
barrel assembly from instrument panel as a unit.
Installation
To install, reverse removal procedure. Ensure air bag door is
securely attached to instrument panel. Ensure air bag harness
connector latches fully engaged. DO NOT connect negative battery cable
at this time. Go to SYSTEM OPERATION CHECK .
CLOCKSPRING
CAUTION: Failure to position wheels in the straight-ahead position
with steering wheel locked when removing steering wheel could
Page 182 of 1691
5) Remove 3 screws securing passenger-side disable switch to
back of switch bezel and remove switch from bezel.
6) To install, reverse removal procedure. Tighten PAD switch
mounting screws to specification. See TORQUE SPECIFICATIONS. DO NOT
connect negative battery cable at this time. Go to
SYSTEM OPERATION CHECK .
Fig. 4: Identifying PAD Switch Connectors
Courtesy of DaimlerChrysler Corp.
ADJUSTMENTS
Page 211 of 1691
AN TI- T H EFT S YSTE M
1999 D odge P ic ku p R 1500
1999 ACCESSORIES & EQUIPMENT
CHRY - Anti-Theft Systems
Ram Pickup, Ram Van & Ram Wagon
DESCRIPTION
The Vehicle Theft Security System (VTSS) provides an engine
no-run feature, flashes headlights and sounds horn if any door or hood
is opened without using key or remote keyless entry transmitter, or if
battery cables are disconnected then reconnected when system is
activated.
Anti-theft system is controlled by Central Timer Module
(CTM). CTM is located under driver's side of dash panel, right of
steering column. If CTM is faulty, CTM cannot be repaired and must be
replaced.
VTSS is also equipped with a power-up mode. If battery is
disconnected or looses power while VTSS is armed, VTSS system remains
armed when power is restored. A temper alert signal is sounded on
vehicle entry if VTSS was triggered while away from vehicle. Horn will
sound 3 times alerting owner VTSS was triggered.
OPERATION
ARMING PROCEDURE (PASSIVE)
Remove key from ignition. Ensure headlights are off. Lock
doors while open, using power lock switch. Power lock switch will not
operate with key in ignition or headlights on while door is open.
Vehicle Theft Security System (VTSS) will not arm using key in lock
cylinder or mechanical lock button. While system is arming, SECURITY
light will flash rapidly for 15 seconds. Opening any door or turning
the ignition key while light is flashing will abort arming process.
Once arming process is complete, SECURITY light will go out.
ARMING PROCEDURE (ACTIVE)
Pressing Remote Keyless Entry (RKE) transmitter LOCK button
will actively arm Vehicle Theft Security System (VTSS). All doors must\
be closed and ignition switch in OFF position. While system is arming,
SECURITY light will flash rapidly for 15 seconds. Opening any door or
turning the ignition key while light is flashing will abort arming
process. Once arming process is complete, SECURITY light will go out.
DISARMING
Vehicle Theft Security System (VTSS) can be disarmed 2 ways:
unlock vehicle using key in any door and pressing remote keyless entry
transmitter UNLOCK button. If alarm has been set off, either method
can be used to disarm and shut-off horn.
CENTRAL TIMER MODULE (CTM)
Central Timer Module (CTM) is Vehicle Theft Security System
(VTSS) processor. CTM uses the data bus network to allow sharing and
reporting of sensor information. If a door ajar sensor is opened while
VTSS is set, a signal is sent to flash headlights and sound horn. PCM
is also notified through bus network to enable engine no-run feature.
Page 212 of 1691
CTM has remote keyless entry receiver and control logic incorporated.
COMPONENT TESTS
RELAYS
NOTE: Headlight relay may also be referred to as the security
relay. On Ram Pickup, the headlight relay is located in Power
Distribution Center (PDC) in engine compartment. On Ram Van
and Ram Wagon, the headlight relay is taped to headlight
switch harness. On Ram Pickup, the horn relay is located in
Power Distribution Center (PDC) in engine compartment. On Ram\
Van and Ram Wagon, the horn relay is located in junction
block under left side of instrument panel. For circuit
testing, see WIRING DIAGRAMS.
Headlight Relay & Horn Relay
Remove relay to be tested. Measure resistance between
appropriate relay terminals with relay de-energized and energized. See
RELAY TEST SPECIFICATIONS table. See Fig. 1. If continuity or
resistance is not as specified, replace relay.
RELAY TEST SPECIFICATIONS
\
\
\
\
\
\
\
Terminals Condition
De-Energized
87A & 30 .............................................. Continuity
87 & 30 ............................................ No Continuity
85 & 86 .................................... 70-80 Ohms Resistance
Energized ( 1)
87 & 30 ............................................... Continuity
87A & 30 ........................................... No Continuity
( 1) - Apply position battery voltage to terminal No. 85 and ground
terminal No. 86.
\
\
\
\
\
\
\
Fig. 1: Identifying Relay Connector Terminals
Courtesy of Chrysler Corp.
SYSTEM TESTS
Page 213 of 1691
For Vehicle Theft Security System (VTSS) testing procedures,
see appropriate BODY CONTROL COMPUTER TESTS article.
REMOVAL & INSTALLATION
CENTRAL TIMER MODULE (CTM)
NOTE: Before removing Central Timer Module (CTM), use scan tool to
view settings for programmable features. Use these settings
to program replacement CTM.
Removal & Installation (Ram Pickup)
1) Disconnect negative battery cable. Remove left underdash
cover and knee bolster reinforcement. Remove 2 CTM retaining screws at
right side of underdash opening. See Fig. 2.
2) Slide CTM down into opening far enough to gain access to
connectors. Disconnect harness connectors and remove CTM from
underdash. To install, reverse removal procedure. Reprogram new CTM.
See appropriate BODY CONTROL COMPUTER TESTS article.
Removal & Installation (Ram Van & Ram Wagon)
1) Disconnect negative battery cable. Remove left underdash
cover and knee bolster reinforcement. Remove 3 CTM retaining screws
from left center instrument panel support. See Fig. 3.
2) Slide CTM away from mounting enough to gain access to
connectors. Disconnect harness connectors and remove CTM from
underdash. To install, reverse removal procedure. Reprogram new CTM.
See appropriate BODY CONTROL COMPUTER TESTS article.
Fig. 2: Identifying CTM Location (Ram Pickup)
Courtesy of Chrysler Corp.
Page 235 of 1691
problem is found, measure resistance between output speed sensor
terminals. If resistance is 300-1200 ohms, go to next step. If
resistance is not as specified, replace output speed sensor.
7) Reconnect output speed sensor. Measure resistance between
ground and output speed sensor ground circuit at PCM harness
connector. If resistance is greater than 5 ohms, go to next step. If
resistance is not as specified, repair output speed sensor ground
circuit for a short to ground.
8) Measure resistance between ground and output speed sensor
signal circuit at PCM harness connector. If resistance is less than 5
ohms, repair output speed sensor signal circuit for a short to ground.
If resistance is not as specified, go to next step.
9) Measure resistance between output speed sensor signal
circuit and ground circuit at PCM harness connector. If resistance is
300-1200 ohms, replace PCM. If resistance is not as specified, go to
next step.
10) Disconnect output speed sensor harness connector. Measure
resistance of output speed sensor signal circuit between output speed
sensor harness connector and PCM harness connector. If resistance is
greater than 5 ohms, repair open in output speed sensor signal
circuit. If resistance is not as specified, repair open in output
speed sensor ground circuit.
11) Turn ignition on. Measure voltage between ground and
speed sensor ground circuit at PCM harness connector. Place gearshift
lever in each gear position and record voltage at each position. If
voltage is greater than one volt in any gear position, repair speed
sensor ground circuit for a short to power. If voltage is not as
specified, go to next step.
12) Raise and support vehicle. Start engine. Place gearshift
lever in "OD" position. Release brakes and allow wheels to rotate.
Using scan tool, monitor output speed sensor. While monitoring output
speed sensor, wiggle harness between output speed sensor and PCM. If
reading dropped towards zero while wiggling harness, repair
intermittent short or open in harness. If reading does not drop
towards zero while wiggling harness, problem is intermittent. See
INACTIVE DTC CONDITION under SELF-DIAGNOSTIC SYSTEM. Testing is
complete.
DTC P0740: TORQ CONV CLU, NO RPM DROP AT LOCKUP
Circuit Description
Circuit is monitored continuously while key is on, and gear
selector is not in Park or Neutral. Code sets if Torque Converter
Clutch (TCC) does not achieve desired drop in RPM when TCC solenoid is\
near maximum duty cycle. A bad test 3 consecutive times is required to
set code.
Possible Causes
* Misfire trouble code set.
* Vehicle stalls (faulty TCC solenoid).
* TCC shaft seal/seal defective.
* Transmission fluid contaminated.
* TCC solenoid wiring harness defective.
* TCC defective.
* TCC hydraulic circuit damaged.
Diagnostic Procedure
1) Using scan tool, read DTCs. On all bodies except AB and WJ
bodies, go to next step. On AB and WJ bodies, if DTC SPECIFIC GOOD
TRIPS counter is not displayed or displayed count is not "0", go to
step 10). If DTC SPECIFIC GOOD TRIPS counter is displayed and
displayed count is "0", indicating DTC still exists, go to next step.
Page 267 of 1691
6) Disconnect PNP switch harness connector. Measure
resistance of PNP switch sense circuit between Black PCM harness
connector C1 and PNP switch harness connector. If resistance is less
than 5 ohms, replace PNP switch. If resistance is not as specified,
repair open in PNP switch sense circuit.
7) Conditions required to set DTC P1899 are not present at
this time. Using scan tool, check and record FREEZE FRAME data. Ensure
"CAUSED BY DTC" "P" code matches code on DTC screen. Using wiring
diagram as a guide, inspect wiring and connectors. Repair wiring
harness as necessary. If wiring and connectors are okay, does not
reset, see INACTIVE DTC CONDITION under SELF-DIAGNOSTIC SYSTEM.
Testing is complete.
TEST VER-2A (EXCEPT DIESEL)
NOTE: If Powertrain Control Module (PCM) is replaced, correct
vehicle mileage and Vehicle Identification Number (VIN) must
be programmed into PCM to prevent Diagnostic Trouble Codes
(DTCs) from being set in Anti-Lock Brake System (ABS) modul\
e
and Supplemental Restraint System (SRS) module. To program
PCM and clear DTCs from ABS and SRS modules, proceed to
appropriate procedure listed below. On models equipped with a
Smart Key Immobilizer Module (SKIM), if replacing Powertrain
Control Module (PCM), secret key data must also be updated to\
enable engine starting. To update secret key data, proceed to
appropriate procedure listed below.
Procedure For Programming PCM & Clearing DTCs From ABS & SRS
Modules
Connect scan tool to Data Link Connector (DLC). Using scan
tool, enter correct VIN and mileage into PCM. Using scan tool
manufacturer's instructions, clear DTCs from ABS and SRS modules. Go
to step 1)).
Procedure For Updating Secret Key Data
Connect scan tool to Data Link Connector (DLC). Go to ENGINE
and then MISC menus on scan tool. Place SKIM in SECURED ACCESS MODE by
using appropriate Personal Identification Number (PIN) for this
vehicle. PIN may be obtained from owner, vehicle's invoice, or from
manufacturer. Select UPDATE THE SECRET KEY DATA. Data will be
transferred from Smart Key Immobilizer Module (SKIM) to PCM. Go to
step 1)).
1) Inspect vehicle to ensure all engine components are
connected. Reassemble and reconnect components as necessary. If test
is being performed after performing a NO TROUBLE CODE (NTC) test, go
to next step. If test is being performed after performing an OBD-II
TROUBLE CODE test, perform TEST VER-5A. If test is being performed
after any other TROUBLE CODE test, go to step 3).
2) Check if initial symptom still exists. If initial or
another symptom exists, repair is not complete. Check for Technical
Service Bulletins (TSBs) that apply to symptom and see appropriate
TEST NTC-1A: NO TROUBLE CODE TEST MENU in ENGINE PERFORMANCE, or
appropriate TROUBLE SHOOTING - NO CODES article in ENGINE PERFORMANCE
for diagnosis by symptom. If initial symptom no longer exists, test is
complete. Go to step 8).
3) If any DTCs have not been diagnosed, perform appropriate
test(s) see appropriate SELF-DIAGNOSTIC TESTS in ENGINE PERFORMANCE.
If all DTCs have been diagnosed and repaired, go to next step.
4) If Powertrain Control Module (PCM) has not been replaced,\
use scan tool to clear DTCs from PCM. Using scan tool, reset all
values in adaptive memory. To ensure no other DTCs remain, go to next
step.
Page 268 of 1691
5) If PCM has not been replaced, and TEST VER-2A is being
performed after an A/C relay control circuit DTC test, ensure A/C is
on and go to next step.
6) Road test vehicle for at least 5 minutes. Road test
vehicle at a speed of at least 40 MPH at some point during road test.
Stop vehicle. Turn engine off for at least 10 seconds. Start engine
and continue road test. Ensure transmission shifts through all gears.
After road test, turn engine off and go to next step.
7) Using scan tool, read DTCs. If any DTC returns, perform
appropriate test(s). If no DTCs return, test is complete. Go to next
step.
8) Turn ignition on, with engine off. Using scan tool, erase
DTCs. Turn ignition off. Disconnect scan tool. Test is complete.
TEST VER-2A (DIESEL)
NOTE: If Accelerator Pedal Position Sensor (APPS), battery, Engine
Control Module (ECM) or Powertrain Control Module (PCM) has\
been disconnected or replaced, APPS must be reprogrammed and
correct vehicle mileage and Vehicle Identification Number
(VIN) must be programmed into PCM to prevent Diagnostic
Trouble Codes (DTCs) from being set in Anti-Lock Brake System\
(ABS) module and Supplemental Restraint System (SRS) module\
.
To program PCM and clear DTCs from ABS and SRS modules,
proceed to appropriate procedure listed below. On models
equipped with a Smart Key Immobilizer Module (SKIM), if
replacing Powertrain Control Module (PCM), secret key data
must also be updated to enable engine starting. To update
secret key data, proceed to appropriate procedure listed
below.
CAUTION: DO NOT attempt to adjust screws or disassemble APPS. Settings
are preset at factory and are not intended to by changed.
Procedure For Programming APPS
Reassemble all components. Turn ignition switch to ON or RUN
position without starting engine. Slowly press accelerator pedal to
floor once and slowly release. This procedure programs APPS
calibration in ECM. Go to step 1)).
Procedure For Programming PCM & Clearing DTCs From ABS & SRS
Modules
Connect scan tool to Data Link Connector (DLC). Using scan
tool, enter correct VIN and mileage into PCM. Using scan tool
manufacturer's instructions, clear DTCs from ABS and SRS modules. Go
to step 1)).
Procedure For Updating Secret Key Data
Connect scan tool to Data Link Connector (DLC). Go to ENGINE
and then MISC menus on scan tool. Place SKIM in SECURED ACCESS MODE by
using appropriate Personal Identification Number (PIN) for this
vehicle. PIN may be obtained from owner, vehicle's invoice, or from
manufacturer. Select UPDATE THE SECRET KEY DATA. Data will be
transferred from Smart Key Immobilizer Module (SKIM) to PCM. Go to
step 1)).
1) If PCM has not been replaced, and TEST VER-2A (DIESEL) is\
being performed after a No Trouble Code (NTC) test, inspect vehicle to\
ensure all engine components are connected. Reassemble and reconnect
components as necessary. Check if initial symptom still exists. If
initial symptom exists, check for Technical Service Bulletins (TSBs)
that apply to vehicle and see TEST NTC-1A: NO TROUBLE CODE TEST MENU
in ENGINE PERFORMANCE, or appropriate TROUBLE SHOOTING - NO CODES