boot DODGE RAM 1999 Service Owner's Guide
[x] Cancel search | Manufacturer: DODGE, Model Year: 1999, Model line: RAM, Model: DODGE RAM 1999Pages: 1691, PDF Size: 40.34 MB
Page 1283 of 1691
Stud loose in
taper hole ............. A ........... (7) Require repair or
replacement.
Taper hole elongated .... A ........ ( 8) Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ........ ( 7) Require replacement.
Wear exceeds
manufacturer's
specifications .......... B ............ Require replacement.
( 1) - If greaseable, grease joint. If problem persists or
joint is non-greaseable, require replacement.
( 2) - Cracked grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 3) - Lack of grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 4) - Torn grease boot will allow contaminants to enter the
joint and will accelerate wear.
( 5) - If manufacturer's procedures for inspection exist, use
those procedures; otherwise, use an approved inspection
method such as the dry park check.
CAUTION: DO NOT use pliers or pry bar to check ball and
socket movement. Use only moderate hand pressure.
( 6) - Excessive looseness is defined as being significant
enough to affect vehicle handling or structural
integrity.
( 7) - Check for damaged taper hole.
( 8) - Check for damaged stud.
\
\
\
\
\
\
\
SHOCK ABSORBERS, STRUT CARTRIDGES AND STRUT ASSEMBLIES
You are not required to replace shocks or struts in axle
sets. However, when replacing a shock or strut due to the conditions
that follow, you may suggest replacement of the other shock or strut
on the same axle for improved performance and preventive maintenance.
* Part is close to the end of its useful life
* To extend tire life
* To balance ride and handling
* To improve stopping distance
When replacing steering and/or suspension components which
may affect an alignment angle, you are required to check and adjust
alignment as needed. Refer to the OEM specifications.
Under no circumstances should a technician bend struts or
strut housings.
A vehicle's load-carrying and handling abilities are limited
by its suspension, tires, brakes, and driveline. Installing coil over
shocks or any other load assist device does not increase the vehicle's
load capacity. See the vehicle owner's manual for more details.
NOTE: If vehicle is equipped with original equipment coil over
shocks, apply the conditions for coil springs from the
SPRINGS - COIL, LEAF AND TORSION BAR section of the
STEERING AND SUSPENSION guidelines. If the vehicle is
equipped with add-on coil over shocks, you may suggest
replacing the shocks with standard shocks for any spring-
related condition.
SHOCK ABSORBER, STRUT CARTRIDGE AND STRUT ASSEMBLY INSPECTION
\
\
\
\
\
\
\
Page 1284 of 1691
Condition Code Procedure
Attaching hardware bent . B ... Require repair or replacement
of bent part, if available;
otherwise, replace shock or
strut.
Attaching hardware
broken ................. A ... Require replacement of broken
part, if available; otherwise,
replace shock or strut.
Attaching hardware
corroded, affecting
structural integrity ... A . Require replacement of corroded
part, if available; otherwise,
replace shock or strut.
Attaching hardware
incorrect .............. A .......... Require replacement of
incorrect part, if available;
otherwise, replace shock or
strut.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part, if available;
otherwise, replace shock or
strut.
Attaching hardware
missing ................ C .. Require replacement of missing
part, if available; otherwise,
replace shock or strut.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads,
if available; otherwise,
replace shock or strut.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads, if
available; otherwise, replace
shock or strut.
Binding ................. A ............ Require replacement.
Body dented ............. A .......... (1) Further inspection
required.
Body punctured .......... A ............ Require replacement.
Brake hose bracket
bent ................... B .. Require repair or replacement.
Brake hose bracket
missing ................ C ............ Require replacement.
Brake hose bracket
threads damaged ........ A .. Require repair or replacement.
Brake hose bracket
threads stripped
(threads missing) ...... C ............ Require replacement.
Compression bumper
missing ................ C .......... Require replacement of
compression bumper.
Compression bumper
split .................. 1 .......... Suggest replacement of
compression bumper.
Damping (none) .......... A ............ Require replacement.
Dust boot (bellows)
split .................. 2 ......... ( 2) Suggest replacement
of boot.
Page 1285 of 1691
Dust boot (bellows)
missing ................ 2 ......... (2) Suggest replacement
of boot.
Dust boot (bellows)
torn ................... 2 ......... ( 2) Suggest replacement
of boot.
Dust shield broken ...... 2 ........ ( 2) Suggest replacement.
Dust shield missing ..... 2 ........ ( 2) Suggest replacement.
Gland nut (strut housing
cap) is not removable
using appropriate tool . A .. ( 3) Require replacement of nut
and/or housing.
Gland nut (strut housing
cap) threads damaged ... A ... Require repair or replacement
of nut.
Gland nut (strut housing
cap) threads stripped
(threads missing) ...... A ..... Require replacement of nut.
Housing dented .......... A .......... ( 1) Further inspection
required.
Housing punctured ....... A ............ Require replacement.
Jounce bumper missing ... C ... Require replacement of jounce
bumper.
Jounce bumper split ..... 1 ... Suggest replacement of jounce
bumper.
Leaking oil, enough for
fluid to be running down
the body ............... A ........ ( 4) Require replacement.
Noise ................... 2 .......... ( 5) Further inspection
required.
Piston rod bent ......... A ............ Require replacement.
Piston rod broken ....... A ............ Require replacement.
Piston rod has surface
defect ................. 2 ............ Suggest replacement.
Piston rod threads
damaged ................ A .. Require repair or replacement.
Piston rod threads
stripped (threads
missing) ............... A ............ Require replacement.
Seized .................. A ............ Require replacement.
Shock missing ........... C ............ Require replacement.
Strut housing bent ...... A ............ Require replacement.
Strut housing cap (gland
nut) is not removable
using appropriate tool . A ......... ( 3) Require replacement
of nut and/or housing.
Strut housing cap (gland
nut) threads damaged ... A ... Require repair or replacement
of nut.
Strut housing cap (gland
nut) threads stripped
(threads missing) ...... A ..... Require replacement of nut.
Strut housing severely
corroded, affecting
structural integrity ... A ............ Require replacement.
Strut housing threads
damaged ................ A .. Require repair or replacement.
Strut housing threads
stripped (threads
missing) ............... A ............ Require replacement.
Tire cupping ............ A .......... ( 6) Further inspection
required.
Page 1290 of 1691
replace steering damper.
Attaching hardware
corroded, affecting
structural integrity ... A . Require replacement of corroded
part, if available; otherwise,
replace steering damper.
Attaching hardware
incorrect .............. A .......... Require replacement of
incorrect part, if available;
otherwise, replace steering
damper.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part, if available;
otherwise, replace steering
damper.
Attaching hardware
missing ................ C .. Require replacement of missing
part, if available; otherwise,
replace steering damper.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads,
if available; otherwise,
replace steering damper.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads, if
available; otherwise, replace
steering damper.
Binding ................. A ............ Require replacement.
Damper body dented ...... A .......... (1) Further inspection
required.
Damper body punctured ... A ............ Require replacement.
Damping (none) .......... A ............ Require replacement.
Dust boot (bellows)
missing ................ 2 ......... ( 2) Suggest replacement
of boot.
Dust boot (bellows)
split .................. 2 ......... ( 2) Suggest replacement
of boot.
Dust shield broken ...... 2 ........ ( 2) Suggest replacement.
Dust shield missing ..... 2 ........ ( 2) Suggest replacement.
Leaking oil, enough for
fluid to be running
down the body .......... A ............ Require replacement.
Loose ................... A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Noise ................... 2 .......... ( 3) Further inspection
required.
Piston rod bent ......... A ............ Require replacement.
Piston rod broken ....... A ............ Require replacement.
Piston rod has surface
defect ................. 2 ............ Suggest replacement.
Piston rod threads
stripped (threads
missing) ............... A ............ Require replacement.
Piston rod threads
damaged ................ A .. Require repair or replacement.
Seized .................. A ............ Require replacement.
( 1) - Require replacement of units where dents restrict damper
Page 1292 of 1691
of seal and/or mating part.
Splines damaged ......... A ... Require repair or replacement
of splines.
Splines stripped ........ A . Require replacement of splines.
Steering coupler
shield cracked ......... 2 ............ Suggest replacement.
Steering coupler
shield missing ......... C ............ Require replacement.
Threads damaged ......... A ... Require repair or replacement
of part with damaged threads.
Threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads.
U-joint binding ......... A ... Require repair or replacement
of joint.
U-joint loose ........... A ... Require repair or replacement
of joint.
Unequal power assist .... A .. Require repair or replacement.
(1) - Determine and correct source of contamination. OEM
specifications must be followed for fluid type.
( 2) - If steering gear is source of inadequate assist, require
repair or replacement.
\
\
\
\
\
\
\
STEERING GEARS - RACK AND PINION
If diagnosis has determined that complete disassembly is
necessary to determine the extent of the system failure, the
suggestion may be made to rebuild or replace the power steering pump.
Repair or replacement of the following components may be required, if
performed as part of a power steering pump overhaul or rebuild service
to meet a minimum rebuild standard.
STEERING GEARS - RACK AND PINION INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ......... Require replacement of
broken part.
Attaching hardware
loose .................. A .. Require repair or replacement
of loose part.
Attaching hardware
missing ................ C ......... Require replacement of
missing part.
Attaching hardware
threads damaged ........ A .. Require repair or replacement
of part with damaged threads.
Attaching hardware
threads stripped
(threads missing) ...... A .... Require replacement of part
with stripped threads.
Balance tube blocked .... A .. Require repair or replacement
of balance tube.
Balance tube missing .... C .. Require replacement of balance
tube.
Balance tube restricted . A ... Require repair or replacement
of balance tube.
Bellows boot
clamp missing .......... C ... Require replacement of clamp.
Bellows boot cracked
Page 1293 of 1691
(not through) .......... 2 .. Suggest replacement of bellows
boot.
Bellows boot missing .... C .. Require replacement of bellows
boot.
Bellows boot
not sealing ............ A ... Require repair or replacement
of bellows boot.
Bellows boot torn ....... A .. Require replacement of bellows
boot.
Bellows boot twisted
(from toe adjustment) .. B ................. Require repair.
Fitting leaking ......... A .. Require repair or replacement.
Fitting missing ......... A . Require replacement of fitting.
Fitting threads
damaged ................ A ... Require repair or replacement
of part with damaged threads.
Fitting threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads.
Flex coupler binding .... A ... Require repair or replacement
of coupler.
Flex coupler loose ...... A ... Require repair or replacement
of coupler.
Flex coupler
missing parts .......... A ... Require repair or replacement
of coupler.
Flex coupler
soft/spongy ............ A . Require replacement of coupler.
Flex coupler torn ....... A . Require replacement of coupler.
Fluid contaminated ...... B ........ (1) Require flushing and
refilling of the system.
Gasket leaking .......... A .. Require repair or replacement.
Hard steering on cold
start-up ............... 1 ........... ( 2) Suggest repair or
replacement.
Housing cracked,
affecting structural
integrity .............. B ............ Require replacement.
Housing leaking ......... A ............ Require replacement.
Inadequate power assist . A .......... ( 3) Further inspection
required.
Lash exceeds
manufacturer's
specifications ......... B .. Require repair or replacement.
Seal leaking ............ A .. Require repair or replacement.
Splines damaged ......... A .. Require repair or replacement.
Splines stripped
(splines missing) ...... A ............ Require replacement.
Steel line blocked ...... A ... Require repair or replacement
of line.
Steel line leaking ...... A ... Require repair or replacement
of line.
Steel line missing ...... C .... Require replacement of line.
Steel line restricted ... A ... Require repair or replacement
of line.
Steering coupler shield
cracked ................ 2 ............ Suggest replacement.
Steering coupler shield
missing ................ C ............ Require replacement.
Steering coupler shield
torn ................... 2 ............ Suggest replacement.
Threads damaged ......... A ... Require repair or replacement
of part with damaged threads.
Page 1297 of 1691
specifications ......... B ............. Require replacement
of bearing.
Bearing binding ......... A ............. Require replacement
of bearing.
Bearing missing ......... C ............. Require replacement
of bearing.
Bearing seized .......... A ............. Require replacement
of bearing.
Bent .................... B ............ Require replacement.
Holes distorted ......... A ............ Require replacement.
Missing ................. C ............ Require replacement.
Severely corroded,
affecting structural
integrity .............. A ............ Require replacement.
\
\
\
\
\
\
\
SWAY BAR LINKS
SWAY BAR LINK INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
incorrect .............. A .......... Require replacement of
incorrect part, if available;
otherwise, replace link.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part, if available;
otherwise, replace link.
Attaching hardware
missing ................ C .. Require replacement of missing
part, if available; otherwise,
replace link.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads,
if available; otherwise,
replace link.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads, if
available; otherwise, replace
link.
Ball and socket has
looseness (perceptible
vertical movement) ..... 1 ........ ( 1) Suggest replacement.
Ball and socket has
looseness that is
excessive .............. B ..... ( 1)( 2) Require replacement.
Bent .................... B ............ Require replacement.
Broken .................. A ............ Require replacement.
Corroded, affecting
structural integrity ... A ............ Require replacement.
Grease boot cracked ..... 2 ........ ( 3) Suggest replacement.
Grease boot missing ..... 2 ........ ( 4) Suggest replacement.
Grease boot torn ........ 2 ........ ( 5) Suggest replacement.
Missing ................. C ............ Require replacement.
Nut on stud loose ....... A ............. ( 6) Require repair.
Stud bent ............... B ........ ( 7) Require replacement.
Stud broken ............. A ........ ( 7) Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Page 1298 of 1691
Threads stripped (threads
missing) ............... A ........ (7) Require replacement.
( 1) - If manufacturer's procedures for inspection exist, use
those procedures; otherwise, use an approved inspection
method such as the dry park check.
CAUTION: DO NOT use pliers or pry bar to check ball and
socket movement. Use only moderate hand pressure.
( 2) - Excessive looseness is defined as being significant
enough to affect vehicle handling or structural
integrity.
( 3) - Cracked grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 4) - Lack of grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 5) - Torn grease boot will allow contaminants to enter the
joint and will accelerate wear.
( 6) - Check for bent stud or damaged taper hole.
( 7) - Check for damaged taper hole.
\
\
\
\
\
\
\
SWAY BARS
SWAY BAR INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require replacement of broken
part, if available; otherwise,
replace sway bar.
Attaching hardware
corroded, affecting
structural integrity ... A .......... Require replacement of
corroded part, if available;
otherwise, replace sway bar.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part, if available;
otherwise, replace sway bar.
Attaching hardware
missing ................ C .. Require replacement of missing
part, if available; otherwise,
replace sway bar.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads,
if available; otherwise,
replace sway bar.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads, if
available; otherwise, replace
sway bar.
Bent .................... B ............ Require replacement.
Broken .................. A ............ Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped
(threads missing) ...... A ............ Require replacement.
\
\
\
\
\
\
\
TIE ROD ENDS (INNER AND OUTER)
Page 1299 of 1691
![DODGE RAM 1999 Service Owners Guide TIE ROD END (INNER AND OUTER) INSPECTION \
\
\
\
\
\
\
Condition](/img/12/56915/w960_56915-1298.png "DODGE RAM 1999 Service Owners Guide TIE ROD END (INNER AND OUTER) INSPECTION \
\
\
\
\
\
\
Condition")
TIE ROD END (INNER AND OUTER) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
incorrect .............. A .......... Require replacement of
incorrect part, if available;
otherwise, replace tie rod end.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part, if available;
otherwise, replace tie rod end.
Attaching hardware
missing ................ C .. Require replacement of missing
part, if available; otherwise,
replace tie rod end.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads,
if available; otherwise,
replace tie rod end.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads, if
available; otherwise, replace
tie rod end.
Adjusting sleeve bent ... B ... Require replacement of sleeve
or tie rod end.
Adjusting sleeve clamps
out of position ........ B ................. Require repair.
Adjusting sleeve
corroded, affecting
structural integrity ... A ... Require replacement of sleeve
or tie rod end.
Adjusting sleeve
missing ................ C ... Require replacement of sleeve
or tie rod end.
Adjusting sleeve
seized ................. A ........... (1) Require repair or
replacement.
Adjusting sleeve
threads damaged ........ A ... Require repair or replacement
of sleeve or tie rod end.
Adjusting sleeve
threads stripped
(threads missing) ...... A ... Require replacement of sleeve
or tie rod end.
Binding ................. A .......... ( 2) Further inspection
required.
Grease boot cracked ..... 2 ........ ( 3) Suggest replacement.
Grease boot missing ..... 2 ........ ( 4) Suggest replacement.
Grease boot torn ........ 2 ........ ( 5) Suggest replacement.
Grease fitting broken ... A ... Require replacement of grease
fitting.
Grease fitting missing .. C ... Require replacement of grease
fitting.
Grease fitting
won't seal ............. A ... Require replacement of grease
fitting.
Grease seal missing ..... 2 ......... ( 4) Suggest replacement
of seal.
Page 1300 of 1691
Grease seal torn ........ 2 ......... (5) Suggest replacement
of seal.
Greaseable tie rod end
won't take grease ...... 2 ...... ( 6) Suggest replacement of
grease fitting.
Looseness (perceptible
horizontal movement) ... 1 ........ ( 7) Suggest replacement.
Looseness exceeds
manufacturer's
specifications ......... B ............ Require replacement.
Looseness that is
excessive .............. B ..... ( 7)( 8) Require replacement.
Nut on stud loose ....... A ........... ( 9) Require repair or
replacement of nut.
Seized .................. A ............. Require replacement
Stud bent ............... B ....... ( 10) Require replacement.
Stud broken ............. A ....... ( 10) Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped
(threads missing) ...... A ....... ( 10) Require replacement.
( 1) - Only required if toe needs to be adjusted.
( 2) - If greaseable, grease joint. If problem persists or
joint is non-greaseable, require replacement.
( 3) - Cracked grease boot will allow contaminants to enter
joint and will accelerate wear.
( 4) - Lack of grease boot will allow contaminants to enter
joint and will accelerate wear.
( 5) - Torn grease boot will allow contaminants to enter joint
and will accelerate wear.
( 6) - If greaseable tie rod end will not take grease after
replacing the grease fitting, suggest replacement of
tie rod end.
( 7) - If manufacturer's procedures for inspection exist, use
those procedures; otherwise, use an approved inspection
method such as the dry park check.
CAUTION: DO NOT use pliers or pry bar to check ball and socket
movement. Use only moderate hand pressure.
( 8) - Excessive looseness is defined as being significant enough
to affect vehicle handling or structural integrity.
( 9) - Check for bent stud or damaged taper hole.
( 10 ) - Check for damaged taper hole.
\
\
\
\
\
\
\
TRACK BARS
TRACK BAR INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
incorrect .............. A .......... Require replacement of
incorrect part, if available;
otherwise, replace track bar.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part, if available;
otherwise, replace track bar.
Attaching hardware
missing ................ C .. Require replacement of missing
part, if available; otherwise,
replace track bar.
Attaching hardware