boot DODGE RAM 1999 Service Manual PDF
[x] Cancel search | Manufacturer: DODGE, Model Year: 1999, Model line: RAM, Model: DODGE RAM 1999Pages: 1691, PDF Size: 40.34 MB
Page 1360 of 1691

Grease seal torn ........ 2 ......... (5) Suggest replacement
of seal.
Greaseable tie rod end
won't take grease ...... 2 ...... ( 6) Suggest replacement of
grease fitting.
Looseness (perceptible
horizontal movement) ... 1 ........ ( 7) Suggest replacement.
Looseness exceeds
manufacturer's
specifications ......... B ............ Require replacement.
Looseness that is
excessive .............. B ..... ( 7)( 8) Require replacement.
Nut on stud loose ....... A ........... ( 9) Require repair or
replacement of nut.
Seized .................. A ............. Require replacement
Stud bent ............... B ....... ( 10) Require replacement.
Stud broken ............. A ....... ( 10) Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped
(threads missing) ...... A ....... ( 10) Require replacement.
( 1) - Only required if toe needs to be adjusted.
( 2) - If greaseable, grease joint. If problem persists or
joint is non-greaseable, require replacement.
( 3) - Cracked grease boot will allow contaminants to enter
joint and will accelerate wear.
( 4) - Lack of grease boot will allow contaminants to enter
joint and will accelerate wear.
( 5) - Torn grease boot will allow contaminants to enter joint
and will accelerate wear.
( 6) - If greaseable tie rod end will not take grease after
replacing the grease fitting, suggest replacement of
tie rod end.
( 7) - If manufacturer's procedures for inspection exist, use
those procedures; otherwise, use an approved inspection
method such as the dry park check.
CAUTION: DO NOT use pliers or pry bar to check ball and socket
movement. Use only moderate hand pressure.
( 8) - Excessive looseness is defined as being significant enough
to affect vehicle handling or structural integrity.
( 9) - Check for bent stud or damaged taper hole.
( 10 ) - Check for damaged taper hole.
\
\
\
\
\
\
\
TRACK BARS
TRACK BAR INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
incorrect .............. A .......... Require replacement of
incorrect part, if available;
otherwise, replace track bar.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part, if available;
otherwise, replace track bar.
Attaching hardware
missing ................ C .. Require replacement of missing
part, if available; otherwise,
replace track bar.
Attaching hardware
Page 1361 of 1691

threads damaged ........ A ... Require repair or replacement
of part with damaged threads,
if available; otherwise,
replace track bar.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads, if
available; otherwise, replace
track bar.
Bent .................... B ............ Require replacement.
Corroded, affecting
structural integrity ... A ............ Require replacement.
Grease boot cracked ..... 2 ........ (1) Suggest replacement.
Grease boot missing ..... 2 ........ ( 2) Suggest replacement.
Grease boot torn ........ 2 ........ ( 3) Suggest replacement.
Holes distorted ......... A ............ Require replacement.
Looseness (perceptible
horizontal movement) ... 1 ........ ( 4) Suggest replacement.
Looseness that is
excessive .............. B ..... ( 4)( 5) Require replacement.
Nut on stud loose ....... A ........... ( 6) Require repair or
replacement of nut.
Seized .................. A ............ Require replacement.
Stud bent ............... B ........ ( 7) Require replacement.
Stud broken ............. A ........ ( 7) Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ........ ( 7) Require replacement.
Wear exceeds
manufacturer's
specifications ......... B ............ Require replacement.
( 1) - Cracked grease boot will allow contaminants to enter
joint and will accelerate wear.
( 2) - Lack of grease boot will allow contaminants to enter
joint and will accelerate wear.
( 3) - Torn grease boot will allow contaminants to enter joint
and will accelerate wear.
( 4) - If manufacturer's procedures for inspection exist, use
those procedures; otherwise, use an approved inspection
method such as the dry park check.
CAUTION: DO NOT use pliers or pry bar to check ball and socket
movement. Use only moderate hand pressure.
( 5) - Excessive looseness is defined as being significant
enough to affect vehicle handling or structural integrity.
( 6) - Check for bent stud or damaged taper hole.
( 7) - Check for damaged taper hole.
\
\
\
\
\
\
\
TRAILING ARMS
TRAILING ARM INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require replacement of broken
part, if available; otherwise,
replace trailing arm.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part, if available;
Page 1580 of 1691

NOTE: Set each front wheel at 1/2 of total toe specification. On
vehicles equipped with power steering, set wheel toe position
with engine running.
Except Ram Van/Wagon & 4WD Models
Center steering wheel and hold with steering wheel clamp.
Loosen tie rod lock nuts. Rotate rods to set toe to specification. See
WHEEL ALIGNMENT SPECIFICATIONS table. Tighten tie rod lock nuts to
specification. See TORQUE SPECIFICATIONS table. Adjust steering gear
to tie rod boots at tie rod. Remove steering wheel clamp. See Fig. 10.
Ram Van/Wagon & 4WD Models
Center steering wheel and hold with steering wheel clamp.
Loosen tie rod adjustment sleeve clamp bolts. Rotate adjustment sleeve
to align toe to specification. See ALIGNMENT SPECIFICATIONS table.
Position sleeve clamps on underside of sleeve so clamp ends are not
over sleeve slot, and tighten adjustment sleeve clamp bolts to
specification. See TORQUE SPECIFICATIONS table. Remove steering wheel
clamp. See Fig. 11.
Fig. 10: Adjusting Front Wheel Toe With Tie Rod (Except Ram
Van/Wagon & 4WD Models)
Courtesy of Chrysler Corp.