wheel DODGE RAM 1999 Service Workshop Manual
[x] Cancel search | Manufacturer: DODGE, Model Year: 1999, Model line: RAM, Model: DODGE RAM 1999Pages: 1691, PDF Size: 40.34 MB
Page 366 of 1691
![DODGE RAM 1999 Service Workshop Manual Wheel Lug Nuts
Dakota .......................................... 85-115 (115-156)\
Ram Pickup
5-Stud Wheel ........................................... 95 (129)\
8-Stud Wheel
Singl](/img/12/56915/w960_56915-365.png "DODGE RAM 1999 Service Workshop Manual Wheel Lug Nuts
Dakota .......................................... 85-115 (115-156)\
Ram Pickup
5-Stud Wheel ........................................... 95 (129)\
8-Stud Wheel
Singl")
Wheel Lug Nuts
Dakota .......................................... 85-115 (115-156)\
Ram Pickup
5-Stud Wheel ........................................... 95 (129)\
8-Stud Wheel
Single Wheel ........................................ 135 (183)\
Dual Wheel .......................................... 145 (197)\
Ram Van
15" Wheel (5 Stud) ............................. 80-110 (109-149\
)
16" Wheel (8 Stud) ............................ 120-150 (163-203\
)
INCH Lbs. (N.m)
Locking Hub Allen Screws ........................... 35-45 (4.0-5.0)\
\
\
\
\
\
\
\
Page 367 of 1691
CLU TC H
1999 D odge P ic ku p R 1500
1998-99 CLUTCHES
CHRY - RWD - Trucks
Dakota, Ram Pickup
DESCRIPTION
Clutches on all models are dry, single-disc design.
Adjustment for wear is not possible. Clutch pedal is connected to
release fork through a hydraulic master cylinder and slave cylinder
and is not adjustable. Pre-lubricated clutch bearing is constant
running type. External adjustments cannot be made.
All models are equipped with a clutch pedal position switch.
The switch completes the circuit to the starter relay and is mounted
on clutch master cylinder push rod. The position switch is an integral
part of clutch master cylinder push rod and cannot be serviced
separately.
TRANSMISSION/TRANSFER CASE APPLICATION
\
\
\
\
\
\
\
Transmission Transfer Case
Dakota
AX15, NV1500 & NV3500 .............................. NV231 & NV242
Ram Pickup
NV3500, NV4500, NV4500HD & NV5600 ..... NV231HD, NV241LD & NV241HD
\
\
\
\
\
\
\
ADJUSTMENTS
CLUTCH PEDAL FREE PLAY
NOTE: Clutches are a single, dry disc type. Adjustment for wear is
not possible. Clutch is actuated through hydraulic master
cylinder and slave cylinder, and is self-adjusting.
SHIFT LINKAGE ADJUSTMENT
NV231 (Dakota)
1) Shift transfer case into 4H position, and secure shift
lever in shift gate. See Fig. 1. Raise and support vehicle. Loosen
shift rod lock bolt at swivel. Ensure shift rod slides freely in
adjusting swivel.
2) Ensure transfer case range lever is in 4H position. Slide
adjusting swivel forward until shift rod contacts shift gate
crossover, then slide adjusting swivel back, allowing a .11-.20" (3-5
mm) gap between shift lever and shift gate.
3) Center pin on adjusting swivel in shift arm and tighten
lock bolt to 90 INCH lbs. (10 N.m.). Lower vehicle, making sure all
wheels are off floor. Start engine. Shift transfer case through all
ranges to verify correct adjustment.
NV231HD, NV241LD & NV241HD (Ram Pickup)
1) Place shift lever into 2H position. Raise and support
vehicle. Loosen shift rod lock bolt at swivel. See Fig. 2. Ensure
shift rod fits in swivel and does not bind.
2) Ensure transfer case shift lever is in 2H position. Lower
vehicle. Position shift lever in cab so distance between instrument
Page 368 of 1691
panel and 2H position dot in shift lever insert is 5.75" (14.6 cm).
Make measurement parallel to floor of vehicle.
3) Tighten shift rod lock bolt to 90 INCH lbs. (10 N.m).
Start engine. Shift transfer case through all ranges to verify proper
operation.
NV242 (Dakota)
1) Put shift lever into 4FT position and secure. Raise
vehicle. Loosen shift rod lock bolt at swivel. See Fig. 1. Ensure
shift rod slides freely in adjusting swivel.
2) Ensure transfer case shift lever is in 4FT position. Slide
adjusting swivel forward until shift lever contacts shifter gate
crossover then slide adjusting swivel back, allowing a 0.11-0.20" (3-5
mm) gap between shift lever and shift gate.
3) Center pin on adjusting swivel in shift arm and tighten
lock bolt to 90 INCH lbs. (10 N.m). Lower vehicle, making sure wheels
are off floor. Start engine. Shift transfer case through all ranges to
verify correct adjustment.
Fig. 1: Adjusting Transfer Case Shift Linkage (Dakota)
Courtesy of Chrysler Corp.
Page 370 of 1691
CLUTCH HOUSING (RAM PICKUP)
NOTE: Only NV4500 clutch housing can be checked using the following
bore and face runout procedures. The NV1500, NV3500 and
NV5600 clutch housings are an integral part of transmission
front case and can only be checked off vehicle.
Clutch Housing Bore Runout (NV4500)
1) Remove clutch housing. Remove clutch cover and disc. See
CLUTCH ASSEMBLY under REMOVAL & INSTALLATION. Replace one flywheel
bolt with a threaded rod. See Fig. 2. Remove release fork from clutch
housing. Reinstall clutch housing. Tighten housing bolts nearest
alignment dowels first. Mount dial indicator on threaded rod and
position indicator plunger on surface of clutch housing bore. See
Fig. 4 .
2) Rotate crankshaft until indicator plunger is at top center
of housing bore. Zero dial indicator. Rotate crankshaft and record
indicator readings at 8 points, 45 degrees apart, around bore. See
Fig. 5 .
3) Repeat measurement at least twice. Subtract each reading
from one 180 degrees opposite to determine magnitude and direction of
runout. For example: 0.000" minus (-0.007") = 0.007", 0.002" minus (-\
0.010") = 0.01", 0.004" minus (-0.005") = 0.009" or -0.001" minus (0\
.
001") = -0.002" which will be 0.002". In this example, largest
difference is 0.012" (total indicator reading). This means housing
bore is offset from crankshaft centerline by 0.006" (1/2 of 0.012").
4) On gas engines, acceptable total indicator reading is 0.
010". If measured total indicator reading is more than 0.010", bore
runout will have to be corrected using offset dowels. Offset dowels
are available in 0.007", 0.014" and 0.021". See DOWEL SELECTION table.
If total indicator reading is 0.053" or greater, replace clutch
housing. If dial indicator reads positive when plunger moves inward
(toward indicator) and negative when moves outward away from
indicator), lowest or most negative reading determines direction of
housing bore offset (runout).
5) On diesel engines, offset dowels are not available to
correct runout. If total indicator reading exceeds bore runout of 0.
015", replace either clutch housing, or transmission adapter plate. On
gas engines, if bore is offset, remove housing and original dowels,
install new offset dowels in direction need to center bore with
crankshaft centerline. Install new dowels with slotted side facing
out. Using a screwdriver, rotate dowels until total indicator reading
is less than 0.010". Ensure clutch housing face runout is within
specification.
DOWEL SELECTION
\
\
\
\
\
\
\
Application - In. (mm) Offset Dowel - In. (mm\
)
0.011-0.021 (0.2794-0.5334) ......................... 0.007 (0.1778\
)
0.022-0.035 (0.5588-0.8890) ......................... 0.014 (0.3556\
)
0.036-0.052 (0.9144-1.3208) ......................... 0.021 (0.5334\
)
\
\
\
\
\
\
\
Fig. 3: Manufactured Stud Or Threaded Rod
Courtesy of Chrysler Corp.
Page 377 of 1691
CAUTION: Clutch disc may contain asbestos fibers which can cause
serious health risk. DO NOT sand clutch components. DO NOT
clean components using compressed air. To clean components,
use a water-dampened cloth.
Removal
With transmission and clutch housing removed, mark pressure
plate and flywheel for reassembly reference. Install clutch aligner in
clutch disc to prevent disc from falling. Loosen pressure plate bolts
evenly and in rotation to avoid warping pressure plate. Remove
pressure plate and disc from flywheel. See Fig. 10.
Inspection
1) Check for oil leakage through engine rear main bearing oil
seal and transaxle input shaft seal. Check flywheel and pressure plate
for burned areas, discoloration, cracks, grooves or ridges. Replace as
necessary.
2) Use medium sandpaper (80-180 grade) to clean flywheel
surface, then wipe with mineral spirits. DO NOT flat-machine flywheel
surface. Check facing surfaces for grease or oil contamination. Check
clutch disc for wear. Clutch disc face-to-rivet head distance should
be at least .008" (.20 mm). Check splines of disc hub and transaxle
input shaft.
3) Using straightedge, check pressure plate. Friction area
should be flat to slightly concave, with the inner diameter about 0-.
0039" (0-0.1 mm) less than outer diameter. Using surface plate, check
clutch cover for flatness. Sections around bolt holes should contact
surface plate within .015" (.38 mm). Ensure cover-to-flywheel dowel
fit is snug. Replace clutch assembly as necessary.
NOTE: Before installing clutch disc, ensure flywheel mating
surface, pilot bearing/bushing and clutch release bearing are
in satisfactory condition. Repair and/or replace components
as necessary.
Installation
To install, reverse removal procedure using clutch aligner.
Ensure reference marks are aligned. Tighten pressure plate retaining
bolts evenly a few threads at a time to prevent warpage. See TORQUE
SPECIFICATIONS table.
Fig. 10: Exploded View Of Clutch Assembly (Typical)
Courtesy of Chrysler Corp.
PILOT BEARING, CLUTCH RELEASE BEARING & FORK
Page 379 of 1691
![DODGE RAM 1999 Service Workshop Manual TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS \
\
\
\
\
\
\](/img/12/56915/w960_56915-378.png "DODGE RAM 1999 Service Workshop Manual TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS \
\
\
\
\
\
\")
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS \
\
\
\
\
\
\
Application Ft. Lbs. (N.m)\
Clutch Master Cylinder Nuts ................................ 40 (54)\
Clutch Slave Cylinder Nuts ................................. 17 (23)\
Crossmember-To-Frame Bolts
AX15 & NV3500 (Dakota) ..................................... 30 (41\
)
NV3500 (Ram Pickup) ........................................ 50 (68\
)
Crossmember-To-Transmission Insulator Nuts
2WD (NV3500 - Ram Pickup) ................................ 50 (68\
)
4WD (NV3500 - Ram Pickup) .......................... 40-45 (54-61\
)
Flywheel Bolts
Dakota 2.5L ................................................ 70 (95)\
Dakota V6 & V8 ............................................. 55 (75)\
Pressure Plate Bolts
5/16" .................................................... 17 (23)\
3/8" ..................................................... 30 (41)\
Transfer Case To Transmission Nuts
AX15 ................................................. 26 (35 N.m)\
NV3500, NV4500, NV4500HD & NV5600
5/16" ............................................. 22-30 (30-41)\
3/8" .............................................. 30-35 (41-47)\
Transmission-To-Clutch Housing Bolts
AX15 ..................................................... 27 (37)\
NV3500 (Ram Pickup) & NV5600 ....................... 40-45 (54-61\
)
NV1500, NV3500 (Dakota), NV4500 & NV 4500HD ............. 80 (108\
)
"U" Joint Clamp Bolts ...................................... 14 (19)\
INCH Lbs. (N.m)
Shift Tower Bolts (NV3500) ............................ 62-89 (7-10\
)
\
\
\
\
\
\
\
Page 383 of 1691
CRUIS E C O NTR O L S YSTE M
1999 D odge P ic ku p R 1500
1999 ACCESSORIES & EQUIPMENT
CHRY - Cruise Control Systems
Dakota, Durango, Ram Pickup, Ram Van & Ram Wagon
CAUTION: When battery is disconnected, vehicle computer and memory
systems may lose memory data. Driveability problems may exist
until computer systems have completed a relearn cycle. See
COMPUTER RELEARN PROCEDURES article in GENERAL INFORMATION
before disconnecting battery.
DESCRIPTION
The speed (cruise) control system is electronically
controlled and vacuum operated. The electronic control is integrated
into the Powertrain Control Module (PCM). System consists of the
following components: Powertrain Control Module (PCM), servo, speed
control switches, vacuum reservoir, vehicle speed sensor, speed
control relay and brake switch.
System controls are located on each side of steering wheel
air bag module and consist of ON/OFF, SET, RESUME/ACCEL, CANCEL AND
COAST buttons. System is designed to operate at speeds above 30 MPH.
OPERATION
SYSTEM CONTROLS
To Set Speed Control
Press ON/OFF button to turn speed control system on.
Accelerate to desired speed (minimum of 35 MPH) and press SET/COAST
button. Vehicle speed will be maintained.
NOTE: Speed control system will automatically disengage when
vehicle speed decreases to less than 35 MPH or increases to
more than 85 MPH.
To Disengage Speed Control
Press brake pedal. Press clutch pedal (M/T). Press CANCEL
button. Press ON/OFF button. If ON/OFF button is used, set speed will
be erased from memory.
To Resume Previous Speed
If set speed has not been erased from memory and vehicle
speed is more than 35 MPH, press RES/ACCEL button.
To Increase Speed
With speed control system on, increase set speed by rapidly
pressing and releasing RES/ACCEL button. Each pressing of button will
cause speed increase of 2 MPH. For example, pressing button 3 times
will increase speed by 6 MPH. To increase speed gradually, hold
RES/ACCEL button down until desired speed is reached. When button is
released, new set speed will be maintained.
To Decrease Speed
With speed control system on, decrease set speed by pressing
SET/COAST button. Vehicle speed will gradually decrease. Releasing
button will set a new speed as long as vehicle speed is still more
than 35 MPH.
Page 390 of 1691
scan tool displayed P/N and D/R in correct positions, go to next step.
4) Raise drive wheels and support vehicle, allowing wheels to
spin. Using scan tool, erase DTCs. Start engine. Using scan tool, read
Output Speed Sensor (OSS). Shift transmission into first gear. While
observing scan tool, allow wheels to spin at a speed less than 15 MPH.
If scan tool displays OSS more than 60 RPM, go to next step. If scan
tool displays OSS 60 RPM or less, go to step 7).
5) While wheels are spinning, wiggle wiring between OSS and
PCM. If OSS reading dropped while wiggling, repair intermittent short
or open circuit. Perform TEST VER-5A under VERIFICATION TESTS. If OSS
reading did not drop, go to next step.
6) Using scan tool, erase DTCs. Road test vehicle. Read DTCs.
If FTC P0720 returns, replace PCM. Perform TEST VER-5A under
VERIFICATION TESTS. If FTC P0720 did not return, go to step 13).
7) Turn ignition off. Disconnect PCM. Inspect connectors.
Clean or repair as necessary. Using an ohmmeter, measure resistance
between ground and OSS signal circuit at PCM connector C2, terminal
No. 28 (Light Green/Black wire on Ram Pickup; Light Green/White wire
on all other models). If resistance is less than 5 ohms, repair short
to ground. Perform TEST VER-5A under VERIFICATION TESTS.
8) Using an ohmmeter, measure resistance between ground and
OSS ground circuit at PCM connector C2, terminal No. 25 (Dark
Blue/Black wire). If resistance is less than 5 ohms, repair short to
ground. Perform TEST VER-5A under VERIFICATION TESTS. If resistance is
5 ohms or more, go to next step.
9) Disconnect OSS. Using an ohmmeter, measure resistance
across OSS terminals. If resistance is not 300-1200 ohms, replace OSS.
Perform TEST VER-5A under VERIFICATION TESTS. If resistance is 300-
1200 ohms, go to next step.
10) Using an ohmmeter, measure resistance of OSS signal
circuit between PCM connector C2, terminal No. 28 and OSS connector
(Light Green/Black wire on Ram Pickup; Light Green/White wire on all
other models). If resistance is more than 5 ohms, repair open circuit.
Perform TEST VER-5A under VERIFICATION TESTS. If resistance is 5 ohms
or less, go to next step.
11) Using an ohmmeter, measure resistance of OSS ground
circuit between PCM connector C2, terminal No. 25 and OSS connector
(Dark Blue/Black wire). If resistance is more than 5 ohms, repair open\
circuit. Perform TEST VER-5A under VERIFICATION TESTS. If resistance
is 5 ohms or less, go to next step.
12) Reconnect OSS. Using an ohmmeter, measure resistance
between PCM connector C2, terminals No. 25 (Dark Blue/Black wire) and
No. 28 (Light Green/Black wire on Ram Pickup; Light Green/White wire
on all other models). If resistance is 300-1200 ohms, replace PCM.
Perform TEST VER-5A under VERIFICATION TESTS. If resistance is not
300-1200 ohms, go to next step.
13) Inspect wiring and connectors. repair as necessary.
Perform TEST VER-5A under VERIFICATION TESTS. If wiring and connectors
are okay, go to next step.
14) Conditions required to set FTC are not present at this
time. Check freeze frame data to determine conditions when FTC was
set. Raise drive wheels and support vehicle, allowing wheels to spin.
Using scan tool, read OSS. Shift transmission into first gear. While
observing scan tool, allow wheels to spin at a speed less than 15 MPH.
Wiggle wiring between OSS and PCM. If OSS reading dropped while
wiggling, repair intermittent short or open circuit. Perform TEST VER-
5A under VERIFICATION TESTS. If OSS reading did not drop, no problem
is indicated at this time.
FTC P1595: SPEED CONTROL SOLENOID CIRCUITS
Speed Control (S/C) solenoid circuits are monitored when
engine is running, S/C switch is on and battery voltage is more than
Page 394 of 1691
voltage. If voltage is less than one volt, go to next step. If voltage
is one volt or more, condition to set FTC is not present at this time.
Test is complete.
2) While observing scan tool, disconnect S/C ON/OFF switch.
If S/C switch voltage changes to 5 volts, replace S/C ON/OFF switch.
Perform TEST VER-4A under VERIFICATION TESTS. If voltage does not
change to 5 volts, go to next step.
3) While observing scan tool, disconnect S/C RESUME/ACCEL
switch. If S/C switch voltage changes to 5 volts, replace S/C
RESUME/ACCEL switch. Perform TEST VER-4A under VERIFICATION TESTS. If
voltage does not change to 5 volts, go to next step.
4) Turn ignition off. Ensure both S/C switches are still
disconnected. Using an ohmmeter, check resistance between S/C switch
connector terminals (S/C switch signal circuit and S/C switch ground
circuit). If resistance is less than 5 ohms, repair short circuit.
Perform TEST VER- 4A under VERIFICATION TESTS. If resistance is 5 ohms
or more, go to next step.
5) Disconnect clockspring 4-pin connector. Clockspring 4-pin
connector is located behind steering wheel. Inspect connector. Clean
or repair as necessary. Using an ohmmeter, check resistance between
ground and S/C switch signal circuit at clockspring connector (Dark
Green/Red wire on all models except Ram Van and Ram Wagon; wire color
is not available for Ram Van and Ram Wagon). If resistance is less
than 5 ohms, repair short to ground. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is 5 ohms or more, go to next step.
6) Disconnect PCM. Inspect connectors. Clean or repair as
necessary. Using an ohmmeter, check resistance between ground and S/C
switch signal circuit at either S/C switch connector (Dark Green/Red
wire on all models except Ram Van and Ram Wagon; wire color is not
available for Ram Van and Ram Wagon). If resistance is less than 5
ohms, repair short to ground. Perform TEST VER-4A under VERIFICATION
TESTS. If resistance is 5 ohms or more, replace PCM. Perform TEST VER-
4A under VERIFICATION TESTS.
FTC P1683: SPEED CONTROL POWER RELAY CIRCUIT
FTC P1683 will set if Speed Control (S/C) power supply
circuit is open or shorted when S/C is turned on.
Possible Causes:
* Brake switch out of adjustment.
* S/C brake switch output circuit open or shorted.
* Defective S/C servo.
* Defective brake switch.
* S/C vacuum or vent solenoid control circuits open or
shorted.
* Defective PCM.
* Ground circuit open.
* S/C power supply circuit open.
NOTE: For component locations, see COMPONENT LOCATIONS. For
connector terminal identification, see CONNECTOR
IDENTIFICATION. For wiring diagram, see WIRING DIAGRAMS.
NOTE: Ensure brake pedal is not depressed during the following
steps.
1) Turn ignition off. Disconnect S/C servo connector. Inspect
connector. Clean or repair as necessary. Turn ignition on. Using scan
tool, actuate S/C relay. Using a 12-volt test light, probe S/C brake
switch output circuit at S/C servo connector terminal No. 3 (Dark
Blue/Red wire). If test light is illuminated and bright, go to next
Page 408 of 1691
FLUID TYPE
Use SAE 80W-90 or 90W hypoid gear lubricant with MIL-L-2105-C
and API GL-5 ratings.
TROUBLE SHOOTING
NOTE: See appropriate table in TROUBLE SHOOTING article in GENERAL
INFORMATION.
REMOVAL & INSTALLATION
AXLE SHAFT & HUB BEARING
Removal
1) Raise and support vehicle. Remove wheel. Remove brake
caliper with hose attached, and secure aside. DO NOT allow brake
caliper to hang by brake hose. Remove brake rotor. Remove ABS wheel
speed sensor (if equipped). Remove grease cap from center of front
hub. Remove cotter pin from end of axle shaft. Remove axle nut and
washer.
2) Remove hub/bearing assembly-to-knuckle bolts. Remove
hub/bearing assembly from steering knuckle and axle shaft. Remove
brake dust shield. To remove right (passenger-side) axle shaft,
carefully pull axle shaft from axle housing.
NOTE: Left axle shaft will disengage from collar located on
intermediate axle shaft.
3) To remove left (driver's side) axle shaft, disconnect
electrical connector and vacuum hoses at vacuum shift motor. Remove
bolts, vacuum shift motor and gasket. Carefully pull axle shaft from
axle housing and collar on intermediate axle shaft.
Installation
1) Install NEW oil seal on axle shaft with seal lip facing
toward splines on differential end of axle shaft. Coat seal lip with
wheel bearing grease.
2) Install right axle shaft into axle housing. Ensure axle
shaft engages with side gears in differential.
3) To install left axle shaft, ensure collar is engaged with
splines on intermediate axle shaft. Install left axle shaft into axle
housing. Ensure axle shaft engages with splines on collar. Install
vacuum shift motor, ensuring fork on vacuum shift motor engages groove
on collar. Install and tighten bolts to specification. See TORQUE
SPECIFICATIONS table.
4) To complete installation, reverse removal procedure. Apply
silicone rubber sealant to edge of grease cap before installing.
Tighten bolts/nuts to specification. See TORQUE SPECIFICATIONS table.
DRIVE SHAFT
Removal
1) Raise and support vehicle. Ensure transmission and
transfer selector levers case are in Neutral. Reference mark drive
shaft and pinion flange for reassembly reference.
2) Remove bolts and "U" joint straps at pinion flange. Remove
center carrier bearing bolts (if equipped). Remove drive shaft.
CAUTION: The "U" joint components are not serviceable. Replace
complete assembly. DO NOT reuse.