weight DODGE RAM 1999 Service Repair Manual
[x] Cancel search | Manufacturer: DODGE, Model Year: 1999, Model line: RAM, Model: DODGE RAM 1999Pages: 1691, PDF Size: 40.34 MB
Page 6 of 1691
"I" ABBREVIATION TABLE (con’t)
ABBREVIATION DEFINITION ISA Idle Speed Actuator ISC Idle Speed Control ISS Idle Stop Solenoid ITS Idle Tracking Switch IVSV Idle Vacuum Switching Valve Ign. Ignition In. Inches Inj. Injector
"J" ABBREVIATION TABLE
"J" ABBREVIATION TABLE
ABBREVIATION DEFINITION J/B Junction Block
"K" ABBREVIATION TABLE
"K" ABBREVIATION TABLE
ABBREVIATION DEFINITION k/ohms 1000 ohms (kilo as in k/ohms) kg Kilograms (weight) kg/cm Kilograms Per Square Centimeter KAM Keep Alive Memory KAPWR Keep Alive Power KM/H Kilometers Per Hour KOEO Key On Engine Off KOER Key On Engine Running KS Knock Sensor
"L" ABBREVIATION TABLE
"L" ABBREVIATION TABLE
ABBREVIATION DEFINITION L Liter(s) L/D Light Duty LCD Liquid Crystal Display LED Light Emitting Diode LH Left Hand LOS Limited Operation Strategy LT BLU Light Blue LT GRN Light Green LUS Lock-Up Solenoid Lbs. Pounds Lt(s). Light(s) Lugg. Luggage
Page 17 of 1691
Use only NEW, moisture-free refrigerant oil in A/C systems.
Refrigerant oil is highly refined with a very low moisture content.
Oil container must be tightly closed when not in use, or moisture from
air will be absorbed into refrigerant oil.
Refrigerant R-134a systems use Polyalkylene Glycol (PAG)
refrigerant oil. Using a mineral oil based lubricant with R-134a
systems will result in A/C compressor failure due to lack of proper
lubrication.
All compressors have different lubrication requirements and
use different Polyalkylene Glycol (PAG) refrigerant oils. Use only the\
specified PAG refrigerant oil for the appropriate system and A/C
compressor. Always check the underhood A/C specification label or A/C
compressor label before adding refrigerant oil to A/C
compressor/system. See listing of refrigerant oils currently available
from the vehicle manufacturers.
NOTE: PAG oil absorbs moisture very rapidly, 2.3-5.6 percent by
weight as compared to a mineral oil absorption rate of .005
percent by weight.
CHRYSLER CORP., JEEP & EAGLE
Use ND-8 PAG oil, SUN PAG 56 oil, SP-10 PAG oil, or SP-20 PAG
oil.
FORD MOTOR CO.
Use YN-12B or YN-12C PAG Refrigerant Oil (specification WSH-
M1C231-B) or SP-20 PAG Oil (specification WST-M1C231-B2).
GENERAL MOTORS
On all models except Saturn, use PAG Refrigerant Oil (Part
No. 12345923). On Saturn, use Saturn PAG refrigerant oil.
SERVICING PRECAUTIONS
DISCHARGING SYSTEM
Discharge A/C system, using approved refrigerant
recovery/recycling equipment before loosening any fittings. Follow
refrigerant recovery/recycling equipment manufacturer's instructions.
DISCONNECTING LINES & FITTINGS
After system is discharged, carefully clean area around all
fittings to be opened. Always use 2 wrenches when loosening or
tightening fittings. Some refrigerant lines are connected with a
spring-lock coupling. Special tools may be required to disconnect
lines. To prevent dirt and moisture from entering system, cap all
openings as soon as lines are removed. DO NOT remove service valve
caps until ready to connect lines and fittings.
NOTE: All R-134a based systems use 1/2-16 ACME threaded fittings.
Ensure all replacement parts match the connections of the
system being worked on.
CONNECTING LINES & FITTINGS
Always use new a gasket or "O" rings when connecting lines or
Page 128 of 1691
A/C S YSTE M G EN ER AL S ER VIC IN G
1999 D odge P ic ku p R 1500
1999 GENERAL SERVICING
A/C System General Servicing
All Models
USING R-134a REFRIGERANT
HANDLING/SAFETY PRECAUTIONS
1) Always work in a well-ventilated, clean area. Refrigerant
is colorless and invisible as a gas. Refrigerant is heavier than
oxygen and will displace oxygen in a confined area. Avoid breathing
refrigerant vapors. Exposure may irritate eyes, nose and throat.
2) Always wear eye protection when working around A/C system
and refrigerant. The system's high pressure can cause severe injury to
eyes and skin if a hose were to burst. If necessary, wear rubber
gloves or other protective clothing.
3) Refrigerant evaporates quickly when exposed to atmosphere,
freezing anything it contacts. If liquid refrigerant contacts eyes or
skin (frostbite), DO NOT rub eyes or skin. Immediately flush affected
area with cool water for 15 minutes and consult a doctor or hospital.
4) Never use R-134a in combination with compressed air for
leak testing. Pressurized R-134a in the presence of oxygen (air
concentrations greater than 60 percent by volume) may form a
combustible mixture. DO NOT introduce compressed air into R-134a
containers (full or empty), A/C system components, or service
equipment.
5) DO NOT expose A/C system components to high temperatures
(steam cleaning for example), as excessive heat will cause refrigerant\
system pressure to increase. Never expose refrigerant directly to open
flame. If refrigerant needs to be warmed, place bottom of refrigerant
tank in warm water. Water temperature MUST NOT exceed 125
F (52 C).
CAUTION: When R-134a is exposed to an open flame, drawn into engine,
or detected with a Halide (propane) leak tester, a poisonous
gas is formed. Keep work areas well ventilated.
6) Use care when handling refrigerant containers. DO NOT
drop, strike, puncture, or incinerate containers. Use DOT 4BW or DOT
4BA approved refrigerant containers.
7) Never overfill refrigerant containers. The safe filling
level of a refrigerant container MUST NOT exceed 60\% of the
container's gross weight rating. Store refrigerant containers at
temperatures less than 125
F (52 C).
8) R-134a refrigerant is sold and stored in 30- or 50-pound
Light Blue containers, while Freon (R-12) is stored in White colored
containers.
9) Refrigerant R-12 and R-134a must never be mixed, as they
and their desiccants and lubricants are not compatible. If the
refrigerants are mixed, system cross-contamination or A/C system
component failure may occur. Always use separate servicing and
refrigerant recovery/recycling equipment.
10) Read and follow equipment manufacturer's instructions for
all service equipment to be used. The Material Safety Data Sheet
(MSDS), provided by refrigerant manufacturer/supplier, contains
valuable information regarding the safe handling of refrigerants.
IDENTIFYING R-134a SYSTEMS & COMPONENTS
Page 131 of 1691
Refrigerant R-12 based systems use mineral oil, while R-134a
systems use synthetic Polyalkylene Glycol (PAG) oils. Using a mineral
oil based lubricant with R-134a will result in A/C compressor failure
due to lack of proper lubrication.
Following are the most common R-134a refrigerant oils used by
most domestic vehicles:
Chrysler Corp., Eagle & Jeep
Use ND-8 PAG oil, SUN PAG 56 oil, SP-10 PAG Oil, or SP-20 PAG
oil.
Ford Motor Co.
Use YN-12B or YN-12C PAG Refrigerant Oil (specification WSH-
M1C231-B) or SP-20 PAG Oil (specification WST-M1C231-B2).
General Motors
On all models except Saturn, use PAG Refrigerant Oil (Part
No. 12345923). On Saturn, use Saturn PAG refrigerant oil.
NOTE: PAG oil absorbs moisture very rapidly, 2.3-5.6 percent by
weight as compared to a mineral oil absorption rate of .005
percent by weight.
NOTE: Use ONLY the specified oil for the appropriate system or A/C
compressor. Always check the underhood A/C specification
label or A/C compressor label before adding refrigerant oil
to A/C system.
SYSTEM SERVICE VALVES
SCHRADER-TYPE VALVES
NOTE: Although similar in construction and operation to a tire
valve, NEVER replace a Schrader-type valve with a tire
valve.
Schrader valve is similar in construction and operation to a
tire valve. See Fig. 4. When a test gauge hose is attached (hose has
built-in valve core depressor), Schrader stem is pushed inward to the
open position and allows system pressure to reach the gauge.
If test hose being used does not have a built-in core
depressor, an adapter must be used. Never attach hoses or adapters to
a Schrader valve unless it is first connected to manifold gauge set.
Fig. 4: Schrader Service Valve (Compressor Location Shown)
SPECIAL VALVE CONNECTORS
On some General Motors models, thread size on high-side
Page 161 of 1691
VALVES. Connect 2 hoses with shutoff valves to manifold gauge set
center port. Connect one hose to vacuum pump and other hose to
refrigerant container. Weight of refrigerant container before and
after charging can be used to determine amount of refrigerant drawn
into system. Using vacuum pump, purge air from center hoses.
3) Fully open manifold gauge set low-side valve and
refrigerant container valve to allow refrigerant to enter A/C system.
When no more refrigerant is being drawn into A/C system, start engine
and allow to idle. Select MAX A/C, set blower motor speed to maximum
and allow remaining refrigerant to be drawn into A/C system.
NOTE: When ambient air temperature is high, it may be necessary to
use an external cooling fan to blow air through condenser and
radiator.
4) When proper amount of refrigerant has been added, close
refrigerant container valve. Allow any refrigerant remaining in hose
to be drawn into A/C system. When low-side pressure decreases to about
30 psi (2.1 kg/cm
), close center valve on manifold gauge set. Ensure
A/C system is operating properly. Disconnect manifold gauge set.
Install service port caps. Check system for leaks. See LEAK TESTING.
GENERAL MOTORS
Manufacturer recommends using A/C Refrigerant Recovery,
Recycling And Recharging (ACR4) System (J-39500). The ACR4 system ha\
s
one filtering cycle during recovery plus an automatic multiple pass
filtering during evacuation cycle. Follow manufacturer's instructions
provided with ACR4 equipment being used.
JEEP
Connect recovery/recycling equipment, meeting SAE standard
J1991 or J2210, to vehicle. Charge A/C system to specifications, using
equipment manufacturer's instructions.
LEAK TESTING
TYPES OF LEAK DETECTORS
Bubble Solution Detector
This is a solution applied externally at suspected leak
points. Leaking refrigerant will cause the detector to form bubbles
and foam. A soap and water solution also works well.
Dye Solution
This is a colored solution that may be introduced into the
A/C system. The dye will show up and color components at leak points.
Some manufacturers offer refrigerant containing a Red dye. This dye-
containing refrigerant is installed by normal charging procedures.
Other dye solutions are visible with a Black light only.
Electronic Leak Detector
This instrument will draw in any leaking refrigerant through
a test probe, and then sound an audible signal or create a flashing
light if refrigerant is found. It is the most sensitive of the leak
detectors used. Leak detectors are sensitive to windshield washing
solutions, many solvents and cleaners, and some adhesives. Ensure
surfaces near test areas are clean and dry to prevent false signal or
detector damage. Liquids ingested into detector will damage detector.
See Fig. 24 .
Page 331 of 1691
![DODGE RAM 1999 Service Repair Manual same axle to eliminate uneven braking behavior. Always wash drums
after servicing or before installing.
DRUM INSPECTION
\
\
\
\](/img/12/56915/w960_56915-330.png "DODGE RAM 1999 Service Repair Manual same axle to eliminate uneven braking behavior. Always wash drums
after servicing or before installing.
DRUM INSPECTION
\
\
\
\")
same axle to eliminate uneven braking behavior. Always wash drums
after servicing or before installing.
DRUM INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Balance weight missing .. .. ........ No service suggested or
required.
Bell-mouthed, affecting
performance ............ A ....... Require reconditioning or
replacement.
Cooling fin broken ...... .. ........ No service suggested or
required.
Cracked ................. B ............ Require replacement.
Drum diameter is greater
than OEM "machine to"
specifications but less
than "discard at"
specifications, and the
drum does not require
reconditioning ......... 1 ........ (1) Suggest replacement.
Drum diameter will exceed
OEM "machine to"
specifications after
required
reconditioning ......... B ........ ( 2) Require replacement.
Hard-spotted ............ 2 ....... Suggest reconditioning or
replacement.
Measured diameter is
greater than OEM discard
specifications ......... B ............ Require replacement.
Out-of-round (runout),
affecting performance .. A ....... Require reconditioning or
replacement.
Out-of-round (runout),
exceeding manufacturer's
specifications ......... B ....... Require reconditioning or
replacement.
Scored .................. B ....... Require reconditioning or
replacement.
Surface threaded due to
improper machining ..... B ....... Require reconditioning or
replacement.
Tapered, affecting
performance ............ A ....... Require reconditioning or
replacement.
( 1) - Only applies to vehicles for which OEM "machine to"
specifications exist. If OEM does not supply "machine to"
specifications, the drum may be worn to discard
specifications.
( 2) - If OEM does not supply "machine to" specifications, you
may machine to discard specifications.
\
\
\
\
\
\
\
ELECTRICAL PUMPS AND MOTORS
Copied fuel pump conditions from engine UIGs & deleted
pulsator from leaking conditions.
ELECTRICAL PUMP AND MOTOR INSPECTION
\
\
\
\
\
\
\
Page 424 of 1691
DRIV E A XLE - R BI F U LL F LO ATIN G A XLE
1999 D odge P ic ku p R 1500
1998-99 DRIVE AXLES
CHRY - RBI Full-Floating Axles
Ram Pickup, Ram Van/Wagon
IDENTIFICATION
REAR DRIVE AXLE APPLICATION \
\
\
\
\
\
\
Application Axle Ring Axle
Model Gear Size Ratio
Ram Pickup ....... 248 RBI .......... 9.75" ... 3.55:1 Or 4.10:1
Ram Pickup ....... 267 RBI ......... 10.50" ... 3.54:1 Or 4.10:1
Ram Pickup ....... 286 RBI ......... 11.00" ... 3.54:1 Or 4.10:1
Ram Van/Wagon .... 248 RBI .......... 9.75" ... 3.55:1 Or 4.10:1
\
\
\
\
\
\
\
DESCRIPTION & OPERATION
The Rear Beam-Design Iron (RBI) axle is an iron center
casting (differential housing) with axle shaft tubes extending from
both sides. The tubes are pressed in to form a one-piece axle housing.
Axle contains an integral carrier with hypoid-type ring gear
and pinion with a solid full-floating axle shaft splined into side
gear. Vehicle weight is supported on tubes of axle housing. Axle
shafts may be serviced without disturbing wheel bearings. On vehicles
equipped with Rear Wheel Anti-Lock (RWAL) brakes, a brake sensor is
mounted on top of axle housing and an exciter ring is mounted on ring
gear.
Axles may be equipped with limited-slip differential. Models
248 and 286 RBI use a Trac-Lok differential and Model 267 RBI uses a
Power-Lok differential as optional equipment. Trac-Lok differential
uses a one-piece case. Power-Lok differential uses a 2-piece case.
Both differentials use same internal components as a standard
differential, except 2 clutch packs are used in the differential case.
NOTE: For servicing of limited-slip differential components in
differential case, see appropriate POWER-LOK or TRAC-LOK
article.
AXLE RATIO & IDENTIFICATION
NOTE: Axle ratio can be identified by axle identification tag
attached to axle housing cover. For axle ratio, see REAR
DRIVE AXLE APPLICATION table at beginning of article.
LUBRICATION
CAPACITY
DRIVE AXLE CAPACITY ( 1) \
\
\
\
\
\
\
Application Pts. (L)\
Ram Pickup
248 RBI ................................................ 6.3 (3.0)\
Page 438 of 1691
DRIV E A XLE - 8 .2 5" & 9 .2 5" R IN G G EA R
1999 D odge P ic ku p R 1500
1998-99 DRIVE AXLES
CHRY - 8 1/4" & 9 1/4" Ring Gears
Dakota, Ram Pickup, Ram Van/Wagon
NOTE: For models using full-floating axles in which vehicle weight
is supported by axle housing tubes, see RBI FULL-FLOATING
AXLES article.
DESCRIPTION & OPERATION
Drive axle contains a solid semi-floating axle shaft splined
into the side gear. On semi-floating axle shafts, vehicle weight is
supported on axle shaft and bearing. Drive shaft rotates the pinion
which drives the ring gear. Power is transferred from ring gear
through side gears to the axle shafts (hypoid gear type).
On rear axles used in vehicles with Rear Wheel Anti-Lock
(RWAL) brakes, a brake sensor is mounted on top of axle housing, and
an exciter ring is mounted on the differential carrier. See Fig. 1.
Fig. 1: Exploded View Of Drive Axle
Courtesy of Chrysler Corp.
AXLE RATIO & IDENTIFICATION
Page 458 of 1691
Apply multipurpose lubricant (NLGI grade 2 EP) to "U" joints
and slip joint fittings.
INSPECTION
Abnormal vibration and noise can come from many driveline
sources. Drive shaft vibration/noise increases with vehicle speed
(MPH). A vibration that occurs within a specific speed is not caused
by drive shaft imbalance. Before overhauling driveline, check for
other causes/sources of possible vibration/noise.
TIRES & WHEELS
Check tire inflation and wheel balance. Check for foreign
objects in tread, damaged tread, mismatched tread patterns or
incorrect tire sizes. Check for bent wheels.
CENTER BEARING
Tighten drive shaft center bearing mounting bolts. If bearing
insulator is deteriorated or oil-soaked, or drive shaft can be moved
up/down in support, replace center bearing support assembly.
ENGINE & TRANSMISSION MOUNTS
Tighten mounting bolts. If rubber mounts are deteriorated or
broken, replace as needed.
DRIVE SHAFT(S)
Check drive shaft(s) for missing weights, broken welds, or
for dents affecting balance. Check for undercoating, mud, snow/ice on
drive shaft(s). Clean shafts thoroughly and test drive.
"U" JOINTS
Check for foreign material lodged in joints and flange/yokes.
Check for loose "U" joint-to-flange mounting bolts. Check for worn "U"
joint needle bearings. Check for Reddish-Brown rust-dust around "U"
joint caps. Replace "U" joints if necessary.
ADJUSTMENTS
CHECKING DRIVE SHAFT PHASING
One-Piece Drive Shafts
1) Ensure "U" joint flanges on either end of drive shaft are
in same plane. See Fig. 2. Drive shafts with slip joints between yokes
often have arrows to aid in alignment. If yokes are not in same plane,
disassemble slip joint from drive shaft splines. Install slip joint
back onto drive shaft splines, aligning "U" joint yokes. Test drive.
2) Single tube type drive shaft has slip joint on outside of
"U" joint yoke (at transmission end). If one-piece tube type drive
shaft yokes are out of alignment, the drive shaft is torque-twisted.
Drive shaft must be replaced.
Page 460 of 1691
1) On drive shafts greater than 30" in length, measure runout
3" from transmission flange/yoke, center bearing yoke and pinion
flange using dial indicator. Maximum runout for Ram Pickup is .030" (.
76 mm) at front and rear end of drive shaft and .035" (.89 mm) at
center of drive shaft. Maximum runout for all other models is .010" (.
25 mm) at front and rear end of drive shaft and .015" (.38 mm) at
center of drive shaft.
2) For drive shafts less than 30" in length, maximum runout
for Pickup is .030" (.76 mm). Maximum runout for all other models is .\
020" (.51 mm). Replace drive shaft if maximum runout is exceeded.
BALANCING DRIVE SHAFT
1) Perform following procedure only after inspecting all
other possible causes of vibration. See INSPECTION. Drive shaft
imbalance may often be cured by disconnecting shaft, rotating it 180
degrees and reconnecting shaft to flange. Test drive to check results.
NOTE: DO NOT run engine for prolonged periods without forced
airflow across radiator. Engine or transmission may
overheat.
2) To balance drive shaft(s), begin by raising rear wheels
off ground and turning drive shaft with engine. Balance testing may be
done by marking drive shaft in 4 positions, 90 degrees apart around
shaft. Place marks about 6" forward of rear flange/yoke weld. Number
marks 1-4.
3) Install large diameter screw-type hose clamp around drive
shaft so clamp's head is in No. 1 position. Spin drive shaft with
engine and note vibrations. If there is little or no change in
vibration intensity, move clamp head to No. 2 position, and repeat
test.
4) Continue procedure until vibration is at lowest level. If
no difference is noted with clamp head moved to all 4 positions,
vibrations may not be due to drive shaft imbalance.
5) If vibration decreases but is not completely eliminated,
place a second clamp at same position, and repeat test. Combined
weight of both clamps in one position may increase vibration. If so,
rotate clamps 1/2" apart, above and below lowest vibration level
position, and repeat test.
6) Continue to rotate clamps, as necessary, until vibration
is at lowest point. If vibration can be eliminated or reduced to
acceptable level, bend back slack end of clamp so screw cannot loosen.
If vibration level is still unacceptable, leave rear clamp(s) in
place, and repeat procedure at front end of drive shaft. Road test
vehicle. On 4WD models, perform procedure on each shaft.
CHECKING VERTICAL ANGLE
One-Piece Drive Shafts
1) Raise and support vehicle so rear wheels can be rotated.
Rotate drive shaft so a pinion flange bearing cap faces downward.
Attach Inclinometer (C-4224) magnet to bearing cap, and measure drive
shaft vertical angle. See Fig. 4. Remove inclinometer.
2) Rotate drive shaft 90 degrees until drive shaft rear yoke
bearing cap faces downward. Attach inclinometer magnet to bearing cap,
and measure drive shaft vertical angle. Difference between 2 measured
angles is drive shaft rear angle. See Fig. 5. Remove inclinometer.
3) Rotate drive shaft until a slip joint yoke bearing cap
faces downward. Attach inclinometer magnet to bearing cap, and note
angle. Remove inclinometer. Rotate drive shaft 90 degrees until drive
shaft front yoke bearing cap faces downward. Attach inclinometer
magnet to bearing cap, and note angle. Remove inclinometer.