radiator DODGE RAM 2001 Service Repair Manual

INSPECTION - BATTERY
When battery is easily accessible, check the test
indicator (green dot), terminal tightness and felt
(grease) washer on battery posts. Recharge battery as
required to assure that the green dot is visible.
When battery is not easily accessible check battery
condition with a voltmeter at the jump start loca-
tions, or check the voltmeter on the instrument panel
(Fig. 11) or (Fig. 12). The reading should be at least
12.4 volts. Recharge battery as required.
NOTE: Refer to service information for proper bat-
tery charging rates and times.
INSPECTION - WIRING
The assembly plant has shipped all vehicles with
the interior lights and most electronic memories non-
functional by way of an Ignition Off Draw (IOD) fuse
removed. The purpose is to reduce the possibility of
battery run-down during shipping and storage.
Vehicles stored after prep should have the IOD
fuse that activates the accessories pulled to prevent
battery drain.
NOTE: Ensure that the IOD fuse is removed to pre-
vent battery drain and possible damage. Vehicles
stored for extended periods after prep should be
washed frequently, to prevent environmental dam-age, and reinspected for storage-related problems
before delivery.
(1) Install the IOD fuse as equipped. (ON vehicles
being delivered, remember to reset radio, clock, com-
pass, etc., as required.)
(2) Check routing and connections of all underhood
wiring-reroute and connect as required.
(3) Make sure the starter, generator and air condi-
tioning clutch wiring are correctly installed, routed,
and in the clips where provided.
(4) For predelivery storage, always pull the IOD
fuse that activates accessories.
Fig. 10 TRANSMISSION COOLER LINES AND
RADIATOR HOSE
1 - TRANSMISSION OIL COOLER LINES
2 - RADIATOR LOWER HOSE
Fig. 11 BATTERY VOLTAGE GAUGE DIESEL ENGINE
Fig. 12 BATTERY VOLTAGE GAUGE GAS ENGINE
BR/BENEW VEHICLE PREPARATION 30 - 7
UNDER HOOD (Continued)

CABLE - INSTALLATION, RELEASE.......23-83
CABLE - INSTALLATION, SPARK PLUG....8I-20
CABLE - INSTALLATION, THROTTLE
CONTROL....................14-105,14-50
CABLE - OPERATION...................8P-4
CABLE - OPERATION, ANTENNA BODY.....8A-4
CABLE - OPERATION, BATTERY..........8F-20
CABLE - OPERATION, SPARK PLUG.......8I-19
CABLE - REMOVAL, CHECK.............23-62
CABLE - REMOVAL, FRONT PARKING
BRAKE..............................5-37
CABLE - REMOVAL, INSTRUMENT PANEL
ANTENNA...........................8A-9
CABLE - REMOVAL, LATCH RELEASE....23-101
CABLE - REMOVAL, RELEASE...........23-82
CABLE - REMOVAL, SPARK PLUG........8I-20
CABLE - REMOVAL, THROTTLE
CONTROL....................14-104,14-50
CABLE 2500/3500 SERIES WITH DRUM
BRAKES - INSTALLATION, REAR PARK
BRAKE..............................5-39
CABLE INSTALLATION, GASOLINE -
NEGATIVE..........................8F-24
CABLE INSTALLATION, GASOLINE -
POSITIVE...........................8F-23
CABLE ORDER, 8.0L V-10 ENGINE -
SPARK PLUG.........................8I-2
CABLE REMOVAL, GASOLINE -
NEGATIVE..........................8F-23
CABLE REMOVAL, GASOLINE - POSITIVE . . 8F-23
CABLE RESISTANCE, SPECIFICATIONS -
SPARK PLUG.........................8I-3
CABLE TENSIONER - ADJUSTMENT.......5-40
CABLES - 1500 SERIES - INSTALLATION,
REAR PARK BRAKE....................5-39
CABLES - 1500 SERIES - REMOVAL,
REAR PARK BRAKE....................5-37
CABLES - DIAGNOSIS & TESTING,
BATTERY...........................8F-20
CABLES - DIAGNOSIS AND TESTING,
SPARK PLUG........................8I-19
CABLES 2500/3500 SERIES WITH DRUM
BRAKES - REMOVAL, REAR PARK
BRAKE..............................5-38
CAB-TO- BED GROUND STRAP -
INSTALLATION.......................8A-14
CAB-TO- BED GROUND STRAP -
REMOVAL..........................8A-14
CALIBRATION - STANDARD PROCEDURE,
COMPASS...........................8M-4
CALIPERS - ASSEMBLY, DISC BRAKE......5-12
CALIPERS - CLEANING, DISC BRAKE......5-12
CALIPERS - DISASSEMBLY, DISC BRAKE . . . 5-11
CALIPERS - INSPECTION, DISC BRAKE....5-12
CAM - DESCRIPTION, TURN SIGNAL
CANCEL............................8L-30
CAM - OPERATION, TURN SIGNAL
CANCEL............................8L-31
CAM BORE REPAIR - STANDARD
PROCEDURE........................9-267
CAM/OVERDRIVE PISTON RETAINER -
ASSEMBLY, OVERRUNNING
CLUTCH.........21-236,21-406,21-581,21-752
CAM/OVERDRIVE PISTON RETAINER -
CLEANING, OVERRUNNING
CLUTCH.........21-236,21-406,21-580,21-752
CAM/OVERDRIVE PISTON RETAINER -
DESCRIPTION, OVERRUNNING
CLUTCH.........21-235,21-405,21-580,21-751
CAM/OVERDRIVE PISTON RETAINER -
DISASSEMBLY, OVERRUNNING
CLUTCH.........21-235,21-405,21-580,21-751
CAM/OVERDRIVE PISTON RETAINER -
INSPECTION, OVERRUNNING
CLUTCH.........21-236,21-406,21-580,21-752
CAM/OVERDRIVE PISTON RETAINER -
OPERATION, OVERRUNNING
CLUTCH.........21-235,21-405,21-580,21-751
CAMSHAFT & BEARINGS (IN BLOCK) -
INSPECTION
........................9-272
CAMSHAFT - INSTALLATION
. 9-144,9-201,9-273,
9-29,9-87
CAMSHAFT - REMOVAL
. 9-143,9-201,9-268,9-29,
9-86
CAMSHAFT BEARINGS - INSTALLATION
. . 9-144,
9-201,9-273,9-29,9-87
CAMSHAFT BEARINGS - REMOVAL
. 9-143,9-200,
9-268,9-29,9-86CANCEL CAM - DESCRIPTION, TURN
SIGNAL............................8L-30
CANCEL CAM - OPERATION, TURN
SIGNAL............................8L-31
CANISTER - DESCRIPTION, VAPOR......25-37
CANISTER - INSTALLATION, CRANKCASE
BREATHER VAPOR...................9-242
CANISTER - INSTALLATION, VAPOR......25-38
CANISTER - OPERATION, VAPOR........25-37
CANISTER - REMOVAL, CRANKCASE
BREATHER VAPOR...................9-241
CANISTER - REMOVAL, VAPOR..........25-37
CAP - CLEANING, RADIATOR PRESSURE . . . 7-66
CAP - DESCRIPTION, FUEL FILLER.......25-33
CAP - DESCRIPTION, RADIATOR
PRESSURE..........................7-65
CAP - DIAGNOSIS AND TESTING,
DISTRIBUTOR.......................8I-12
CAP - DIAGNOSIS AND TESTING,
RADIATOR...........................7-66
CAP - INSPECTION, RADIATOR
PRESSURE..........................7-66
CAP - OPERATION, FUEL FILLER........25-33
CAP - OPERATION, RADIATOR
PRESSURE..........................7-65
CAP - REMOVAL/INSTALLATION, FUEL
FILLER.............................25-33
CAPACITIES, SPECIFICATIONS - FLUID......0-6
CAPACITY TEST - DIAGNOSIS AND
TESTING, FUEL PUMP..................14-9
CAP-TO-FILLER NECK SEAL -
DIAGNOSIS AND TESTING, RADIATOR.....7-66
CARDAN UNIVERSAL JOINTS -
DISASSEMBLY, SINGLE.................3-11
CARDAN UNIVERSAL JOINTS -
INSTALLATION, SINGLE............3-34,3-66
CARDAN UNIVERSAL JOINTS -
REMOVAL, SINGLE................3-33,3-65
CAREFUL NEW VEHICLE PREPARATION -
DESCRIPTION, THE IMPORTANCE OF......30-1
CARGO BOX - INSTALLATION...........23-97
CARGO BOX - REMOVAL...............23-96
CARGO DOOR - ADJUSTMENT..........23-78
CARPETS AND FLOOR MATS -
INSTALLATION......................23-123
CARPETS AND FLOOR MATS - REMOVAL . 23-123
CARTRIDGE FUSE - DESCRIPTION,
GENERATOR......................8W-97-4
CARTRIDGE FUSE - INSTALLATION,
GENERATOR......................8W-97-4
CARTRIDGE FUSE - OPERATION,
GENERATOR......................8W-97-4
CARTRIDGE FUSE - REMOVAL,
GENERATOR......................8W-97-4
CASE - DIAGNOSIS AND TESTING,
TRANSFER.............21-821,21-856,21-892
CASE - INSPECTION, TRANSMISSION/
TRANSFER..........................30-15
CASE - NV231HD - ASSEMBLY,
TRANSFER.........................21-834
CASE - NV231HD - CLEANING,
TRANSFER.........................21-831
CASE - NV231HD - DESCRIPTION,
TRANSFER.........................21-820
CASE - NV231HD - DISASSEMBLY,
TRANSFER.........................21-822
CASE - NV231HD - INSPECTION,
TRANSFER.........................21-832
CASE - NV231HD - INSTALLATION,
TRANSFER.........................21-847
CASE - NV231HD - OPERATION,
TRANSFER.........................21-820
CASE - NV231HD - REMOVAL,
TRANSFER.........................21-822
CASE - NV241HD - ASSEMBLY,
TRANSFER.........................21-904
CASE - NV241HD - CLEANING,
TRANSFER.........................21-902
CASE - NV241HD - DESCRIPTION,
TRANSFER
.........................21-890
CASE - NV241HD - DISASSEMBLY,
TRANSFER
.........................21-894
CASE - NV241HD - INSPECTION,
TRANSFER
.........................21-902
CASE - NV241HD - INSTALLATION,
TRANSFER
.........................21-919
CASE - NV241HD - OPERATION,
TRANSFER
.........................21-892CASE - NV241HD - REMOVAL,
TRANSFER.........................21-894
CASE - NV241LD - ASSEMBLY,
TRANSFER.........................21-869
CASE - NV241LD - CLEANING,
TRANSFER.........................21-866
CASE - NV241LD - DESCRIPTION,
TRANSFER.........................21-855
CASE - NV241LD - DISASSEMBLY,
TRANSFER.........................21-858
CASE - NV241LD - INSPECTION,
TRANSFER.........................21-867
CASE - NV241LD - INSTALLATION,
TRANSFER.........................21-882
CASE - NV241LD - OPERATION,
TRANSFER.........................21-855
CASE - NV241LD - REMOVAL,
TRANSFER.........................21-858
CASE BEARINGS - INSTALLATION,
DIFFERENTIAL . . . 3-103,3-134,3-164,3-192,3-39,
3-71
CASE BEARINGS - REMOVAL,
DIFFERENTIAL . . . 3-103,3-134,3-164,3-192,3-39,
3-71
CASE FLUID - DESCRIPTION, TRANSFER....0-5
CASE, NV231HD - TRANSFER..........21-849
CASE, NV241HD - TRANSFER..........21-920
CASE, NV241LD - TRANSFER..........21-884
CASE SKID PLATE - INSTALLATION,
TRANSFER..........................13-11
CASE SKID PLATE - REMOVAL,
TRANSFER..........................13-11
CASE, SPECIFICATIONS - TRANSFER.....21-848,
21-883,21-919
CASTER CORRECTION MEASUREMENT -
STANDARD PROCEDURES...............2-3
CATALYTIC CONVERTER - 3.9L/5.2L/5.9L
- DESCRIPTION.......................11-5
CATALYTIC CONVERTER - 3.9L/5.2L/5.9L
- INSPECTION........................11-5
CATALYTIC CONVERTER - 3.9L/5.2L/5.9L
- INSTALLATION......................11-5
CATALYTIC CONVERTER - 3.9L/5.2L/5.9L
- OPERATION.........................11-5
CATALYTIC CONVERTER - 3.9L/5.2L/5.9L
- REMOVAL..........................11-5
CATALYTIC CONVERTER - 5.9L HEAVY
DUTY/8.0L - DESCRIPTION..............11-6
CATALYTIC CONVERTER - 5.9L HEAVY
DUTY/8.0L - INSPECTION...............11-7
CATALYTIC CONVERTER - 5.9L HEAVY
DUTY/8.0L - INSTALLATION.............11-7
CATALYTIC CONVERTER - 5.9L HEAVY
DUTY/8.0L - OPERATION................11-6
CATALYTIC CONVERTER - 5.9L HEAVY
DUTY/8.0L - REMOVAL.................11-6
CATCH - INSPECTION, HOOD LATCH/
SAFETY.............................30-4
CAUSES OF BURNT FLUID - DIAGNOSIS
AND TESTING....21-199,21-370,21-545,21-715
CAUTION, INTERIOR.................23-118
CAUTION, REFRIGERANT HOSES/LINES/
TUBES PRECAUTIONS.................24-42
CCD DATA BUS - DESCRIPTION..........8E-6
CCD DATA BUS - DIAGNOSIS AND
TESTING...........................8E-11
CCD DATA BUS - OPERATION............8E-7
CENTER - DESCRIPTION, POWER
DISTRIBUTION....................8W-97-7
CENTER - INSTALLATION, POWER
DISTRIBUTION
....................8W-97-8
CENTER - OPERATION, POWER
DISTRIBUTION
....................8W-97-8
CENTER - REMOVAL, POWER
DISTRIBUTION
....................8W-97-8
CENTER BEARING - CENTER BEARING
ADJUSTMENT
........................3-10
CENTER BEARING - DESCRIPTION
........3-10
CENTER BEARING - INSTALLATION
.......3-10
CENTER BEARING - OPERATION
..........3-10
CENTER BEARING - REMOVAL
...........3-10
CENTER BEARING ADJUSTMENT,
CENTER BEARING
.....................3-10
CENTER CONSOLE - INSTALLATION
.....23-122
CENTER CONSOLE - REMOVAL
.........23-122
CENTER CONSOLE LID - INSTALLATION
. . 23-132
CENTER CONSOLE LID - REMOVAL
.....23-131
6 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

CONTROL/CENTRAL TIMER MODULE -
INSTALLATION, BODY..................8E-6
CONTROL/CENTRAL TIMER MODULE -
OPERATION, BODY....................8E-3
CONTROL/CENTRAL TIMER MODULE -
REMOVAL, BODY......................8E-5
CONTROLLER ANTILOCK BRAKE -
DESCRIPTION.......................8E-11
CONTROLLER ANTILOCK BRAKE -
INSTALLATION.......................8E-12
CONTROLLER ANTILOCK BRAKE -
OPERATION.........................8E-11
CONTROLLER ANTILOCK BRAKE -
REMOVAL..........................8E-12
CONTROLS - DIAGNOSIS AND TESTING,
OVERDRIVE
ELECTRICAL.....21-215,21-386,21-579,21-732
CONVERTER - 3.9L/5.2L/5.9L -
DESCRIPTION, CATALYTIC...............11-5
CONVERTER - 3.9L/5.2L/5.9L -
INSPECTION, CATALYTIC................11-5
CONVERTER - 3.9L/5.2L/5.9L -
INSTALLATION, CATALYTIC..............11-5
CONVERTER - 3.9L/5.2L/5.9L -
OPERATION, CATALYTIC................11-5
CONVERTER - 3.9L/5.2L/5.9L -
REMOVAL, CATALYTIC..................11-5
CONVERTER - 5.9L HEAVY DUTY/8.0L -
DESCRIPTION, CATALYTIC...............11-6
CONVERTER - 5.9L HEAVY DUTY/8.0L -
INSPECTION, CATALYTIC................11-7
CONVERTER - 5.9L HEAVY DUTY/8.0L -
INSTALLATION, CATALYTIC..............11-7
CONVERTER - 5.9L HEAVY DUTY/8.0L -
OPERATION, CATALYTIC................11-6
CONVERTER - 5.9L HEAVY DUTY/8.0L -
REMOVAL, CATALYTIC..................11-6
CONVERTER - DESCRIPTION,
TORQUE........21-256,21-427,21-600,21-773
CONVERTER - INSTALLATION,
TORQUE........21-261,21-432,21-605,21-778
CONVERTER - OPERATION,
TORQUE........21-260,21-430,21-604,21-777
CONVERTER - REMOVAL,
TORQUE........21-261,21-432,21-605,21-778
CONVERTER DRAINBACK VALVE -
DESCRIPTION,
TORQUE........21-262,21-432,21-605,21-778
CONVERTER DRAINBACK VALVE -
OPERATION,
TORQUE........21-262,21-432,21-605,21-778
CONVERTER DRAINBACK VALVE -
STANDARD PROCEDURE,
TORQUE........21-262,21-432,21-606,21-778
CONVERTER HOUSING FLUID LEAK -
DIAGNOSIS AND
TESTING........21-148,21-319,21-491,21-662
COOLANT - DESCRIPTION...............7-40
COOLANT - OPERATION
................7-40
COOLANT - STANDARD PROCEDURE,
ADDING ADDITIONAL
..................7-16
COOLANT FLOW - DIAGNOSIS AND
TESTING, RADIATOR
...........7-59,7-61,7-63
COOLANT LEVEL CHECK - STANDARD
PROCEDURE
.........................7-16
COOLANT RECOVERY CONTAINER -
3.9L/5.2L/5.9L/5.9L DIESEL -
DESCRIPTION
........................7-41
COOLANT RECOVERY CONTAINER -
3.9L/5.2L/5.9L/5.9L DIESEL -
INSTALLATION
........................7-41
COOLANT RECOVERY CONTAINER -
3.9L/5.2L/5.9L/5.9L DIESEL -
OPERATION
..........................7-41
COOLANT RECOVERY CONTAINER -
3.9L/5.2L/5.9L/5.9L DIESEL -
REMOVAL
...........................7-41
COOLANT RECOVERY CONTAINER - 8.0L
- DESCRIPTION
.......................7-42
COOLANT RECOVERY CONTAINER - 8.0L
- OPERATION
.........................7-42
COOLANT SELECTION-ADDITIVES -
STANDARD PROCEDURE
................7-17
COOLANT TEMP SENSOR - 3.9L/5.2L/
5.9L - DESCRIPTION, ENGINE
............7-48
COOLANT TEMP SENSOR - 3.9L/5.2L/
5.9L - INSTALLATION, ENGINE
...........7-48COOLANT TEMP SENSOR - 3.9L/5.2L/
5.9L - OPERATION, ENGINE.............7-48
COOLANT TEMP SENSOR - 3.9L/5.2L/
5.9L - REMOVAL, ENGINE...............7-48
COOLANT THERMOSTAT - 3.9L/5.2L/
5.9L - DESCRIPTION, ENGINE............7-49
COOLANT THERMOSTAT - 3.9L/5.2L/
5.9L - INSTALLATION, ENGINE...........7-50
COOLANT THERMOSTAT - 3.9L/5.2L/
5.9L - OPERATION, ENGINE.............7-49
COOLANT THERMOSTAT - 3.9L/5.2L/
5.9L - REMOVAL, ENGINE...............7-49
COOLANT THERMOSTAT - 5.9L DIESEL -
DESCRIPTION, ENGINE.................7-54
COOLANT THERMOSTAT - 5.9L DIESEL -
INSTALLATION, ENGINE................7-55
COOLANT THERMOSTAT - 5.9L DIESEL -
OPERATION, ENGINE...................7-54
COOLANT THERMOSTAT - 5.9L DIESEL -
REMOVAL, ENGINE....................7-55
COOLANT THERMOSTAT - 8.0L -
DESCRIPTION, ENGINE.................7-52
COOLANT THERMOSTAT - 8.0L -
INSTALLATION, ENGINE................7-53
COOLANT THERMOSTAT - 8.0L -
OPERATION, ENGINE...................7-52
COOLANT THERMOSTAT - 8.0L -
REMOVAL, ENGINE....................7-52
COOLER - 3.9L/5.2L/5.9L - ASSEMBLY,
TRANS..............................7-82
COOLER - 3.9L/5.2L/5.9L -
DESCRIPTION, TRANS.................7-79
COOLER - 3.9L/5.2L/5.9L -
DISASSEMBLY, TRANS...................7-81
COOLER - 3.9L/5.2L/5.9L -
INSTALLATION, TRANS.................7-82
COOLER - 3.9L/5.2L/5.9L - OPERATION,
TRANS..............................7-79
COOLER - 3.9L/5.2L/5.9L - REMOVAL,
TRANS..............................7-81
COOLER - 5.9L DIESEL - DESCRIPTION,
TRANS..............................7-85
COOLER - 5.9L DIESEL - INSTALLATION,
TRANS..............................7-88
COOLER - 5.9L DIESEL - OPERATION,
TRANS..............................7-85
COOLER - 8.0L - DESCRIPTION, TRANS....7-82
COOLER - 8.0L - INSTALLATION, TRANS . . . 7-85
COOLER - 8.0L - OPERATION, TRANS.....7-82
COOLER - 8.0L - REMOVAL, TRANS.......7-84
COOLER - INSTALLATION, AIR TO OIL.....7-88
COOLER & LINES - CLEANING AND
INSPECTION, OIL.....................9-296
COOLER - REMOVAL, AIR TO OIL.........7-87
COOLER - REMOVAL, WATER TO OIL......7-87
COOLER - STANDARD PROCEDURE,
FLUSHING COOLER AND TUBES -
WITHOUT RADIATOR IN-TANK
TRANSMISSION OIL...........7-80,7-83,7-86
COOLER - STANDARD PROCEDURE,
FLUSHING COOLERS AND TUBES -
WITH RADIATOR IN-TANK
TRANSMISSION OIL...........7-79,7-83,7-85
COOLER AND PLUMBING - CLEANING,
CHARGE AIR........................11-18
COOLER AND PLUMBING -
DESCRIPTION, CHARGE AIR............11-17
COOLER AND PLUMBING - INSPECTION,
CHARGE AIR........................11-18
COOLER AND PLUMBING -
INSTALLATION, CHARGE AIR...........11-18
COOLER AND PLUMBING - OPERATION,
CHARGE AIR........................11-17
COOLER AND PLUMBING - REMOVAL,
CHARGE AIR........................11-17
COOLER AND TUBES - WITHOUT
RADIATOR IN-TANK TRANSMISSION
OIL COOLER - STANDARD
PROCEDURE, FLUSHING
........7-80,7-83,7-86
COOLERS AND TUBES - WITH
RADIATOR IN-TANK TRANSMISSION
OIL COOLER - STANDARD
PROCEDURE, FLUSHING
........7-79,7-83,7-85
COOLING, SPECIAL TOOLS
..............7-18
COOLING SYSTEM - OPERATION
..........7-4
COOLING SYSTEM 3.9L/5.2L/5.9L/8.0L
ENGINES - STANDARD PROCEDURE,
DRAINING
...........................7-15COOLING SYSTEM 3.9L/5.2L/5.9L/8.0L
ENGINES - STANDARD PROCEDURE,
REFILLING...........................7-15
COOLING SYSTEM 5.9L DIESEL ENGINE
- STANDARD PROCEDURE, DRAINING.....7-15
COOLING SYSTEM 5.9L DIESEL ENGINE
- STANDARD PROCEDURE, REFILLING.....7-15
COOLING SYSTEM CLEANING/REVERSE
FLUSHING - STANDARD PROCEDURE.....7-16
COOLING SYSTEM DIESEL ENGINE -
DIAGNOSIS AND TESTING..............7-12
COOLING SYSTEM FLOW - 3.9L/5.2L/
5.9L ENGINE - DESCRIPTION.............7-1
COOLING SYSTEM FLOW - 5.9L DIESEL
- DESCRIPTION........................7-1
COOLING SYSTEM GAS ENGINE -
DIAGNOSIS AND TESTING...............7-7
COOLING SYSTEM LEAKS - DIAGNOSIS
AND TESTING.........................7-5
COOLING SYSTEM REQUIREMENTS -
DESCRIPTION........................24-1
CORE - DESCRIPTION, HEATER.........24-55
CORE - INSTALLATION, HEATER.........24-56
CORE - OPERATION, HEATER...........24-55
CORE - REMOVAL, HEATER............24-56
CORE GROUND STRAP - INSTALLATION,
HEATER............................8A-15
CORE GROUND STRAP - REMOVAL,
HEATER............................8A-14
CORNER SEAL - INSTALLATION, FRONT
DOOR UPPER......................23-154
CORNER SEAL - REMOVAL, FRONT
DOOR UPPER........................23-154
COUPLERS - DESCRIPTION, A/C LINE....24-40
COUPLERS - OPERATION, A/C LINE......24-41
COUPLERS - STANDARD PROCEDURE,
A/C LINE...........................24-43
COVER - INSTALLATION, CENTER SEAT
ARMREST/LATCH...................23-132
COVER - INSTALLATION, COWL TRIM . . . 23-120
COVER - INSTALLATION, GEAR HOUSING . 9-307
COVER - INSTALLATION, INSTRUMENT
PANEL TOP........................23-115
COVER - INSTALLATION, SEAT BACK....23-137
COVER - INSTALLATION, SEAT CUSHION . 23-139
COVER - INSTALLATION, SHIFT . . . 21-133,21-90
COVER - INSTALLATION, STANCHION....23-143
COVER - INSTALLATION, STEERING
COLUMN OPENING..................23-116
COVER - REMOVAL, CENTER SEAT
ARMREST/LATCH...................23-132
COVER - REMOVAL, COWL TRIM.......23-119
COVER - REMOVAL, GEAR HOUSING.....9-306
COVER - REMOVAL, INSTRUMENT
PANEL TOP........................23-114
COVER - REMOVAL, SEAT BACK........23-137
COVER - REMOVAL, SEAT CUSHION.....23-139
COVER - REMOVAL, SHIFT.......21-132,21-90
COVER - REMOVAL, STANCHION.......23-143
COVER - REMOVAL, STEERING COLUMN
OPENING..........................23-115
COVER - REMOVAL, WHEEL............22-12
COVER - SPLIT BENCH - INSTALLATION,
SEAT BACK........................23-138
COVER - SPLIT BENCH - INSTALLATION,
SEAT CUSHION.....................23-140
COVER - SPLIT BENCH - REMOVAL,
SEAT BACK........................23-137
COVER - SPLIT BENCH - REMOVAL,
SEAT CUSHION.....................23-139
COVER GASKET - DESCRIPTION,
CYLINDER...........................9-79
COVER GASKET - DESCRIPTION,
CYLINDER HEAD......................9-22
COVER GASKET - OPERATION,
CYLINDER HEAD......................9-22
COVER INSTALLED - INSTALLATION,
FRONT OIL SEAL - FRONT.............9-205
COVER INSTALLED - REMOVAL, FRONT
OIL SEAL - FRONT
...................9-204
COVER REMOVED - INSTALLATION,
FRONT OIL SEAL - FRONT
.............9-205
COVER REMOVED - REMOVAL, FRONT
OIL SEAL - FRONT
...................9-204
COVER(S) - CLEANING, CYLINDER HEAD
. 9-138,
9-194,9-24,9-253,9-81
COVER(S) - DESCRIPTION, CYLINDER
HEAD
..............................9-194
BR/BEINDEX 9
Description Group-Page Description Group-Page Description Group-Page

COVER(S) - INSPECTION, CYLINDER
HEAD............9-138,9-194,9-24,9-253,9-81
COVER(S) - INSTALLATION, CYLINDER
HEAD............9-138,9-194,9-24,9-253,9-81
COVER(S) - INSTALLATION, TIMING
BELT / CHAIN.........9-113,9-169,9-226,9-56
COVERS - INSTALLATION, WHEEL.......30-10
COVER(S) - REMOVAL, CYLINDER HEAD . 9-138,
9-194,9-24,9-253,9-81
COVER(S) - REMOVAL, TIMING BELT /
CHAIN...............9-113,9-169,9-225,9-56
COWL GRILLE - INSTALLATION.........23-90
COWL GRILLE - REMOVAL.............23-90
COWL TRIM COVER - INSTALLATION....23-120
COWL TRIM COVER - REMOVAL.......23-119
COWL WEATHERSTRIP - INSTALLATION . 23-153
COWL WEATHERSTRIP - REMOVAL.....23-153
C-PILLAR TRIM - INSTALLATION.......23-128
C-PILLAR TRIM - REMOVAL...........23-128
CRANKCASE BREATHER VAPOR
CANISTER - INSTALLATION.............9-242
CRANKCASE BREATHER VAPOR
CANISTER - REMOVAL................9-241
CRANKCASE VENT HOSE - OPERATION . . . 25-32
CRANKSHAFT - DESCRIPTION . 9-145,9-275,9-31,
9-88
CRANKSHAFT - INSTALLATION....9-145,9-203,
9-32,9-89
CRANKSHAFT - OPERATION....9-145,9-31,9-88
CRANKSHAFT - REMOVAL . . 9-145,9-202,9-31,9-88
CRANKSHAFT JOURNAL CLEARANCE -
STANDARD PROCEDURE, CONNECTING
ROD BEARING.......................9-274
CRANKSHAFT MAIN BEARING FITTING -
STANDARD PROCEDURE...........9-146,9-90
CRANKSHAFT MAIN BEARINGS -
DESCRIPTION...............9-146,9-32,9-90
CRANKSHAFT MAIN BEARINGS -
INSTALLATION.........9-147,9-204,9-34,9-90
CRANKSHAFT MAIN BEARINGS -
OPERATION.................9-146,9-32,9-90
CRANKSHAFT MAIN BEARINGS -
REMOVAL.............9-147,9-204,9-33,9-90
CRANKSHAFT OIL SEAL - FRONT -
DESCRIPTION...............9-147,9-34,9-91
CRANKSHAFT OIL SEAL - FRONT -
INSTALLATION.........9-148,9-277,9-34,9-91
CRANKSHAFT OIL SEAL - FRONT -
OPERATION.................9-147,9-34,9-91
CRANKSHAFT OIL SEAL - FRONT -
REMOVAL.............9-147,9-276,9-34,9-91
CRANKSHAFT OIL SEAL - REAR -
DESCRIPTION...............9-148,9-34,9-91
CRANKSHAFT OIL SEAL - REAR -
INSTALLATION....9-149,9-206,9-278,9-35,9-92
CRANKSHAFT OIL SEAL - REAR -
OPERATION.................9-148,9-34,9-92
CRANKSHAFT OIL SEAL - REAR -
REMOVAL........9-149,9-206,9-278,9-35,9-92
CRANKSHAFT REAR OIL SEAL RETAINER
- INSTALLATION................9-206,9-279
CRANKSHAFT REAR OIL SEAL RETAINER
- REMOVAL....................9-206,9-278
CROSSHEADS - CLEANING.............9-249
CROSSHEADS - INSPECTION...........9-250
CRUISE INDICATOR - DESCRIPTION......8J-18
CRUISE INDICATOR - OPERATION.......8J-18
CUBBY BIN - INSTALLATION...........23-110
CUBBY BIN - REMOVAL..............23-110
CUMMINS TURBO DIESEL -
DESCRIPTION, MAINTENANCE
SCHEDULES - 24-VALVE................0-22
CUP HOLDER - INSTALLATION.........23-111
CUP HOLDER - REMOVAL.............23-110
CUSHION - INSTALLATION, SEAT.......23-138
CUSHION - REMOVAL, SEAT...........23-138
CUSHION COVER - INSTALLATION, SEAT . 23-139
CUSHION COVER - REMOVAL, SEAT.....23-139
CUSHION COVER - SPLIT BENCH -
INSTALLATION, SEAT.................23-140
CUSHION COVER - SPLIT BENCH -
REMOVAL, SEAT....................23-139
CYLINDER - DESCRIPTION, MASTER
......5-29
CYLINDER - DIAGNOSIS AND TESTING,
IGNITION SWITCH AND KEY LOCK
.......19-10
CYLINDER - INSTALLATION, LOCK
.......23-73
CYLINDER - INSTALLATION, MASTER
.....5-30
CYLINDER - OPERATION, MASTER
........5-29CYLINDER - REMOVAL, LOCK...........23-73
CYLINDER - REMOVAL, MASTER.........5-30
CYLINDER BLEEDING - STANDARD
PROCEDURE, MASTER.................5-30
CYLINDER BORE HONING - STANDARD
PROCEDURE...........9-10,9-126,9-180,9-69
CYLINDER BORE REPAIR - STANDARD
PROCEDURE........................9-265
CYLINDER COMBUSTION PRESSURE
LEAKAGE - DIAGNOSIS AND TESTING....9-124,
9-179,9-67,9-9
CYLINDER COMPRESSION PRESSURE -
DIAGNOSIS AND TESTING . 9-124,9-179,9-67,9-9
CYLINDER COVER GASKET -
DESCRIPTION........................9-79
CYLINDER HEAD - CLEANING . 9-137,9-193,9-23,
9-248,9-80
CYLINDER HEAD - DESCRIPTION . . 9-136,9-191,
9-22,9-246,9-79
CYLINDER HEAD - INSPECTION....9-137,9-193,
9-23,9-250,9-80
CYLINDER HEAD - INSTALLATION . . 9-137,9-193,
9-23,9-250,9-80
CYLINDER HEAD - OPERATION . . 9-136,9-22,9-79
CYLINDER HEAD - REMOVAL . 9-137,9-192,9-23,
9-246,9-80
CYLINDER HEAD COVER GASKET -
DESCRIPTION........................9-22
CYLINDER HEAD COVER GASKET -
OPERATION..........................9-22
CYLINDER HEAD COVER(S) - CLEANING . . 9-138,
9-194,9-24,9-253,9-81
CYLINDER HEAD COVER(S) -
DESCRIPTION.......................9-194
CYLINDER HEAD COVER(S) -
INSPECTION......9-138,9-194,9-24,9-253,9-81
CYLINDER HEAD COVER(S) -
INSTALLATION....9-138,9-194,9-24,9-253,9-81
CYLINDER HEAD COVER(S) - REMOVAL . . 9-138,
9-194,9-24,9-253,9-81
CYLINDER HEAD GASKET FAILURE -
DIAGNOSIS AND TESTING....9-136,9-191,9-22,
9-79
CYLINDER HOUSING - INSTALLATION,
LOCK..............................19-11
CYLINDER HOUSING - REMOVAL, LOCK . . 19-10
CYLINDER LOCK SWITCH -
DESCRIPTION, DOOR..................8N-5
CYLINDER LOCK SWITCH - DIAGNOSIS
& TESTING, DOOR....................8N-5
CYLINDER LOCK SWITCH -
INSTALLATION, DOOR.................8N-6
CYLINDER LOCK SWITCH - OPERATION,
DOOR..............................8N-5
CYLINDER LOCK SWITCH - REMOVAL,
DOOR..............................8N-6
CYLINDER/POWER BOOSTER -
DIAGNOSIS AND TESTING, MASTER......5-29
CYLINDERS - ASSEMBLY, WHEEL.........5-31
CYLINDERS - CLEANING, WHEEL.........5-31
CYLINDERS - DESCRIPTION, LOCK.......23-1
CYLINDERS - DISASSEMBLY, WHEEL......5-31
CYLINDERS - INSPECTION, WHEEL.......5-31
CYLINDERS - INSTALLATION, WHEEL.....5-32
CYLINDERS - REMOVAL, WHEEL.........5-31
DAM - INSTALLATION, FRONT AIR........13-2
DAM - REMOVAL, FRONT AIR...........13-1
DAMAGED OR WORN THREADS -
STANDARD PROCEDURE,
REPAIR ..........9-11,9-125,9-181,9-238,9-68
DAMPER - INSPECTION, VIBRATION.....9-289
DAMPER - INSTALLATION,
VIBRATION.......9-156,9-212,9-289,9-42,9-99
DAMPER - REMOVAL,
VIBRATION.......9-155,9-212,9-289,9-42,9-99
DATA BUS - DESCRIPTION, CCD..........8E-6
DATA BUS - DIAGNOSIS AND TESTING,
CCD ...............................8E-11
DATA BUS - OPERATION, CCD...........8E-7
DATA LINK CONNECTOR - DESCRIPTION . . 8E-12
DATA LINK CONNECTOR - OPERATION
....8E-12
DATA PLATE - DESCRIPTION, ENGINE
....9-244
DATA PLATE, SPECIFICATIONS - FUEL
INJECTION PUMP
....................14-73
DAY / NIGHT MIRROR - DESCRIPTION,
AUTOMATIC
........................8N-10
DAY / NIGHT MIRROR - INSTALLATION,
AUTOMATIC
........................8N-12DAY / NIGHT MIRROR - OPERATION,
AUTOMATIC........................8N-11
DAY / NIGHT MIRROR - REMOVAL,
AUTOMATIC........................8N-12
DAY/NIGHT MIRROR - DIAGNOSIS AND
TESTING, AUTOMATIC................8N-11
DAYTIME RUNNING LAMP MODULE -
DESCRIPTION........................8L-9
DAYTIME RUNNING LAMP MODULE -
INSTALLATION........................8L-9
DAYTIME RUNNING LAMP MODULE -
OPERATION..........................8L-9
DAYTIME RUNNING LAMP MODULE -
REMOVAL...........................8L-9
DECALS - INSTALLATION..............23-63
DECALS - INSTALLATION, BODY
STRIPES...........................23-87
DECALS - REMOVAL..................23-63
DECALS - REMOVAL, BODY STRIPES.....23-87
DEFINITION - DESCRIPTION, TRIP.......25-18
DEFROSTER AND DEMISTER DUCT
ADAPTER - INSTALLATION.............24-35
DEFROSTER AND DEMISTER DUCT
ADAPTER - REMOVAL.................24-35
DEFROSTER AND DEMISTER DUCTS -
INSTALLATION.......................24-35
DEFROSTER AND DEMISTER DUCTS -
REMOVAL..........................24-34
DE-GLAZE - STANDARD PROCEDURE-
CYLINDER BORE.....................9-264
DELIVERY - DIESEL - OPERATION, FUEL . . 14-56
DELIVERY - SPECIFICATIONS, TORQUE -
FUEL...............................14-4
DELIVERY STORAGE - DESCRIPTION,
PRE ...............................30-19
DELIVERY STORAGE - STANDARD
PROCEDURE, PRE....................30-20
DELIVERY SYSTEM - DESCRIPTION,
DIESEL FUEL........................14-54
DELIVERY SYSTEM - DESCRIPTION,
FUEL...............................14-2
DELIVERY SYSTEM - OPERATION, FUEL . . . 14-2
DEMAGNETIZING - STANDARD
PROCEDURE, COMPASS...............8M-5
DEMISTER DUCT ADAPTER -
INSTALLATION, DEFROSTER............24-35
DEMISTER DUCT ADAPTER - REMOVAL,
DEFROSTER.........................24-35
DEMISTER DUCTS - INSTALLATION,
DEFROSTER.........................24-35
DEMISTER DUCTS - REMOVAL,
DEFROSTER.........................24-34
DEMISTER DUCTS - REMOVAL,
INSTRUMENT PANEL..................24-37
DEMISTER GRILLES - INSTALLATION.....24-32
DEMISTER GRILLES - REMOVAL........24-31
DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER AN
AIRBAG.............................8O-4
DETECTION PUMP - DESCRIPTION, LEAK . 25-33
DETECTION PUMP - INSTALLATION,
LEAK..............................25-34
DETECTION PUMP - REMOVAL, LEAK....25-34
DIAGNOSIS - INTRODUCTION -
DIAGNOSIS AND TESTING, ENGINE . 9-118,9-173,
9-3
DIAGNOSIS - MECHANICAL - DIAGNOSIS
AND TESTING, ENGINE................9-232
DIAGNOSIS CHARTS - DIAGNOSIS AND
TESTING........21-149,21-320,21-492,21-663
DIAGNOSIS CHARTS - DIAGNOSIS AND
TESTING, SMOKE....................9-234
DIAGNOSIS, INTRODUCTION -
DIAGNOSIS AND TESTING-ENGINE........9-61
DIAGNOSTIC AND TESTING, CLUTCH.......6-2
DIAGNOSTIC TROUBLE CODES -
DESCRIPTION........................25-2
DIAGNOSTICS (OBD) - DIAGNOSIS AND
TESTING, ON-BOARD...................7-4
DIAGRAMS - DESCRIPTION, HOW TO
USE WIRING
......................8W-01-1
DIAGRAMS - HYDRAULIC SCHEMATICS,
SCHEMATICS
.....21-174,21-345,21-520,21-690
DIESEL - CLEANING, RADIATOR - 5.9L
....7-65
DIESEL - CLEANING, RADIATOR FAN -
5.9L
................................7-44
DIESEL - CLEANING, WATER PUMP -
5.9L
................................7-73
10 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

DIESEL - DESCRIPTION................25-1
DIESEL - DESCRIPTION........14-102,14-103
DIESEL - DESCRIPTION.................8I-5
DIESEL - DESCRIPTION, 5.9L............11-3
DIESEL - DESCRIPTION, BELT
TENSIONERS - 5.9L...................7-23
DIESEL - DESCRIPTION, COOLANT
RECOVERY CONTAINER - 3.9L/5.2L/
5.9L/5.9L............................7-41
DIESEL - DESCRIPTION, COOLING
SYSTEM FLOW - 5.9L...................7-1
DIESEL - DESCRIPTION, ENGINE 5.9L....9-231
DIESEL - DESCRIPTION, ENGINE BLOCK
HEATER - 5.9L........................7-47
DIESEL - DESCRIPTION, ENGINE
COOLANT THERMOSTAT - 5.9L...........7-54
DIESEL - DESCRIPTION, FAN DRIVE
VISCOUS CLUTCH - 5.9L...............7-57
DIESEL - DESCRIPTION, MAINTENANCE
SCHEDULES - 24-VALVE CUMMINS
TURBO..............................0-22
DIESEL - DESCRIPTION, RADIATOR -
5.9L................................7-63
DIESEL - DESCRIPTION, TRANS COOLER
- 5.9L..............................7-85
DIESEL - DESCRIPTION, VACUUM PUMP
- 5.9L..............................7-34
DIESEL - DESCRIPTION, WATER PUMP -
5.9L................................7-73
DIESEL - FUEL INJECTOR FIRING ORDER . 14-58
DIESEL - INSPECTION, EXHAUST PIPE -
5.9L................................11-9
DIESEL - INSPECTION, RADIATOR - 5.9L . . . 7-65
DIESEL - INSPECTION, RADIATOR FAN -
5.9L................................7-44
DIESEL - INSPECTION, TAILPIPE - 5.9L . . . 11-12
DIESEL - INSPECTION, WATER PUMP -
5.9L................................7-73
DIESEL - INSTALLATION..............14-103
DIESEL - INSTALLATION................8I-8
DIESEL - INSTALLATION, BELT
TENSIONERS - 5.9L...................7-23
DIESEL - INSTALLATION, COOLANT
RECOVERY CONTAINER - 3.9L/5.2L/
5.9L/5.9L............................7-41
DIESEL - INSTALLATION, DRIVE BELTS -
5.9L................................7-34
DIESEL - INSTALLATION, ENGINE BLOCK
HEATER - 5.9L........................7-47
DIESEL - INSTALLATION, ENGINE
COOLANT THERMOSTAT - 5.9L...........7-55
DIESEL - INSTALLATION, EXHAUST PIPE
- 5.9L..............................11-10
DIESEL - INSTALLATION, MUFFLER -
5.9L...............................11-11
DIESEL - INSTALLATION, RADIATOR -
5.9L................................7-65
DIESEL - INSTALLATION, RADIATOR FAN
- 5.9L..............................7-45
DIESEL - INSTALLATION, TAILPIPE - 5.9L . 11-12
DIESEL - INSTALLATION, TRANS
COOLER - 5.9L.......................7-88
DIESEL - INSTALLATION, VACUUM
PUMP - 5.9L.........................7-37
DIESEL - INSTALLATION, WATER PUMP -
5.9L................................7-74
DIESEL - OPERATION
.................8E-18
DIESEL - OPERATION
.................25-19
DIESEL - OPERATION
..........14-102,14-103
DIESEL - OPERATION
...................8I-5
DIESEL - OPERATION, BELT
TENSIONERS - 5.9L
...................7-23
DIESEL - OPERATION, COOLANT
RECOVERY CONTAINER - 3.9L/5.2L/
5.9L/5.9L
............................7-41
DIESEL - OPERATION, ENGINE BLOCK
HEATER - 5.9L
........................7-47
DIESEL - OPERATION, ENGINE COOLANT
THERMOSTAT - 5.9L
...................7-54
DIESEL - OPERATION, FAN DRIVE
VISCOUS CLUTCH - 5.9L
...............7-57
DIESEL - OPERATION, FUEL DELIVERY
. . . 14-56
DIESEL - OPERATION, NON-MONITORED
CIRCUITS
...........................25-23
DIESEL - OPERATION, RADIATOR - 5.9L
. . . 7-63
DIESEL - OPERATION, TRANS COOLER -
5.9L
................................7-85DIESEL - OPERATION, VACUUM PUMP -
5.9L................................7-35
DIESEL - OPERATION, WATER PUMP -
5.9L................................7-73
DIESEL - REMOVAL............14-103,14-104
DIESEL - REMOVAL....................8I-7
DIESEL - REMOVAL, BELT TENSIONERS -
5.9L................................7-23
DIESEL - REMOVAL, COOLANT
RECOVERY CONTAINER - 3.9L/5.2L/
5.9L/5.9L............................7-41
DIESEL - REMOVAL, DRIVE BELTS - 5.9L . . 7-33
DIESEL - REMOVAL, ENGINE BLOCK
HEATER - 5.9L........................7-47
DIESEL - REMOVAL, ENGINE COOLANT
THERMOSTAT - 5.9L...................7-55
DIESEL - REMOVAL, EXHAUST PIPE -
5.9L................................11-9
DIESEL - REMOVAL, MUFFLER - 5.9L.....11-11
DIESEL - REMOVAL, RADIATOR - 5.9L.....7-63
DIESEL - REMOVAL, RADIATOR FAN -
5.9L................................7-44
DIESEL - REMOVAL, TAILPIPE - 5.9L.....11-12
DIESEL - REMOVAL, VACUUM PUMP -
5.9L................................7-35
DIESEL - REMOVAL, WATER PUMP -
5.9L................................7-73
DIESEL ENGINE - DESCRIPTION, FUEL
REQUIREMENTS.......................0-2
DIESEL ENGINE - DIAGNOSIS AND
TESTING............................11-4
DIESEL ENGINE - DIAGNOSIS AND
TESTING, COOLING SYSTEM............7-12
DIESEL ENGINE - INSTALLATION........19-35
DIESEL ENGINE - REMOVAL............19-33
DIESEL ENGINE - STANDARD
PROCEDURE, DRAINING COOLING
SYSTEM 5.9L........................7-15
DIESEL ENGINE - STANDARD
PROCEDURE, REFILLING COOLING
SYSTEM 5.9L........................7-15
DIESEL ENGINE - TORQUE.............14-90
DIESEL ENGINE, SPECIAL TOOLS - 5.9L . . 9-244
DIESEL ENGINES - DESCRIPTION,
COMPONENT MONITORS..............25-18
DIESEL ENGINES - FUEL SYSTEM
PRESSURES........................14-58
DIESEL FUEL DELIVERY SYSTEM -
DESCRIPTION.......................14-54
DIESEL FUEL INJECTION SYSTEM -
DESCRIPTION.......................14-87
DIESEL FUEL SYSTEM, SPECIAL TOOLS . . 14-59
DIESEL FUEL TANK - DESCRIPTION......14-78
DIESEL, SPECIFICATIONS - 5.9L.........9-242
DIESEL WITH AUTO. TRANS. -
INSTALLATION..................8P-11,8P-4
DIESEL WITH AUTO. TRANS. - REMOVAL . . 8P-4,
8P-8
DIFFERENTIAL - ASSEMBLY . . 3-128,3-159,3-188,
3-37,3-69,3-98
DIFFERENTIAL - DISASSEMBLY....3-128,3-158,
3-188,3-36,3-68,3-97
DIFFERENTIAL - INSTALLATION....3-129,3-159,
3-188,3-37,3-69,3-98
DIFFERENTIAL - POWR-LOK - ASSEMBLY . 3-163
DIFFERENTIAL - POWR-LOK -
DISASSEMBLY.......................3-161
DIFFERENTIAL - REMOVAL . . 3-127,3-158,3-187,
3-36,3-68,3-96
DIFFERENTIAL - TRAC-LOK - ASSEMBLY . . 3-101,
3-132,3-190
DIFFERENTIAL - TRAC-LOK -
DISASSEMBLY..............3-130,3-190,3-99
DIFFERENTIAL CASE BEARINGS -
INSTALLATION . . . 3-103,3-134,3-164,3-192,3-39,
3-71
DIFFERENTIAL CASE BEARINGS -
REMOVAL . . . 3-103,3-134,3-164,3-192,3-39,3-71
DIMENSION, SPECIFICATIONS - FRAME....13-7
DIMENSIONS, SPECIFICATIONS - BODY
OPENING...........................23-60
DIODE - INSTALLATION............8W-01-10
DIODE - REMOVAL
................8W-01-10
DIODE REPLACEMENT - STANDARD
PROCEDURE
.........................24-7
DISC - DESCRIPTION, CLUTCH
............6-7
DISC - INSTALLATION, CLUTCH
...........6-9
DISC - OPERATION, CLUTCH
.............6-8DISC - REMOVAL, CLUTCH...............6-8
DISC BRAKE CALIPERS - ASSEMBLY......5-12
DISC BRAKE CALIPERS - CLEANING......5-12
DISC BRAKE CALIPERS - DISASSEMBLY . . . 5-11
DISC BRAKE CALIPERS - INSPECTION.....5-12
DISC BRAKE ROTOR - DIAGNOSIS AND
TESTING............................5-20
DISC BRAKES - DESCRIPTION,
2500/3500 WITH REAR.................5-35
DISC BRAKES - INSTALLATION, REAR
PARK BRAKE CABLE - 2500/3500
WITH REAR..........................5-38
DISC BRAKES - OPERATION, 2500/3500
WITH REAR..........................5-36
DISC BRAKES - REMOVAL, REAR PARK
BRAKE CABLE - 2500/3500 WITH
REAR...............................5-37
DISCHARGE LINE - INSTALLATION,
SUCTION...........................24-51
DISCHARGE LINE - REMOVAL, SUCTION . . 24-50
DISPLAY TEST MODE - DESCRIPTION,
STATE ..............................25-1
DISTRIBUTION - DESCRIPTION, POWER . 8W-97-1
DISTRIBUTION - OPERATION, POWER . . 8W-97-1
DISTRIBUTION CENTER - DESCRIPTION,
POWER..........................8W-97-7
DISTRIBUTION CENTER - INSTALLATION,
POWER..........................8W-97-8
DISTRIBUTION CENTER - OPERATION,
POWER..........................8W-97-8
DISTRIBUTION CENTER - REMOVAL,
POWER...........................8W-97-8
DISTRIBUTION SYSTEMS, SPECIAL
TOOLS - POWER...................8W-97-2
DISTRIBUTOR - DESCRIPTION..........8I-10
DISTRIBUTOR - INSTALLATION..........8I-11
DISTRIBUTOR - OPERATION............8I-11
DISTRIBUTOR - REMOVAL..............8I-11
DISTRIBUTOR BUSHING - INSTALLATION . 9-150,
9-37,9-94
DISTRIBUTOR BUSHING - REMOVAL.....9-150,
9-37,9-94
DISTRIBUTOR CAP - DIAGNOSIS AND
TESTING............................8I-12
DISTRIBUTOR ROTOR - DIAGNOSIS AND
TESTING............................8I-13
DOME LAMP - INSTALLATION..........8L-33
DOME LAMP - REMOVAL..............8L-33
DOOR - ADJUSTMENT, CARGO..........23-78
DOOR - INSTALLATION...........23-68,23-78
DOOR - INSTALLATION, BLEND.........24-38
DOOR - INSTALLATION, FUEL FILL.......23-95
DOOR - INSTALLATION, HEAT/DEFROST . . . 24-39
DOOR - INSTALLATION, PANEL/DEFROST . . 24-39
DOOR - INSTALLATION, RECIRCULATION . . 24-39
DOOR - REMOVAL...............23-68,23-78
DOOR - REMOVAL, BLEND.............24-38
DOOR - REMOVAL, FUEL FILL..........23-95
DOOR - REMOVAL, HEAT/DEFROST......24-38
DOOR - REMOVAL, PANEL/DEFROST.....24-38
DOOR - REMOVAL, RECIRCULATION.....24-39
DOOR ACTUATOR - INSTALLATION,
BLEND.............................24-26
DOOR ACTUATOR - INSTALLATION,
HEAT/DEFROST......................24-27
DOOR ACTUATOR - INSTALLATION,
PANEL/DEFROST
.....................24-27
DOOR ACTUATOR - INSTALLATION,
RECIRCULATION
.....................24-28
DOOR ACTUATOR - REMOVAL, BLEND
....24-25
DOOR ACTUATOR - REMOVAL,
HEAT/DEFROST
......................24-26
DOOR ACTUATOR - REMOVAL,
PANEL/DEFROST
.....................24-27
DOOR ACTUATOR - REMOVAL,
RECIRCULATION
.....................24-27
DOOR AJAR SWITCH - DESCRIPTION
....8L-34
DOOR AJAR SWITCH - DIAGNOSIS AND
TESTING
...........................8L-34
DOOR AJAR SWITCH - INSTALLATION
....8L-35
DOOR AJAR SWITCH - REMOVAL
........8L-35
DOOR CYLINDER LOCK SWITCH -
DESCRIPTION
........................8N-5
DOOR CYLINDER LOCK SWITCH -
DIAGNOSIS & TESTING
................8N-5
DOOR CYLINDER LOCK SWITCH -
INSTALLATION
.......................8N-6
BR/BEINDEX 11
Description Group-Page Description Group-Page Description Group-Page

ENGINE (1500 AND 2500 MODELS
EXCEPT 8.0L) MAINTENANCE
SCHEDULES, MAINTENANCE
SCHEDULES - LIGHT DUTY...............0-7
ENGINE, 3.9L.........................9-19
ENGINE 3.9L - DESCRIPTION.............9-3
ENGINE 3.9L - INSTALLATION............9-13
ENGINE 3.9L - REMOVAL...............9-12
ENGINE 5.2L - DESCRIPTION............9-60
ENGINE 5.2L - INSTALLATION............9-70
ENGINE 5.2L - REMOVAL...............9-69
ENGINE 5.9L - DESCRIPTION...........9-117
ENGINE 5.9L - INSTALLATION...........9-127
ENGINE 5.9L - REMOVAL..............9-126
ENGINE 5.9L DIESEL - DESCRIPTION.....9-231
ENGINE 8.0L - DESCRIPTION...........9-172
ENGINE 8.0L - INSTALLATION...........9-182
ENGINE 8.0L - REMOVAL..............9-181
ENGINE BLOCK - CLEANING . . 9-142,9-200,9-28,
9-86
ENGINE BLOCK - INSPECTION.....9-142,9-200,
9-267,9-28,9-86
ENGINE BLOCK - STANDARD
PROCEDURE-CYLINDER BLOCK
REFACING..........................9-263
ENGINE BLOCK HEATER - 3.9L/5.2L/
5.9L - DESCRIPTION...................7-45
ENGINE BLOCK HEATER - 3.9L/5.2L/
5.9L - INSTALLATION..................7-45
ENGINE BLOCK HEATER - 3.9L/5.2L/
5.9L - OPERATION.....................7-45
ENGINE BLOCK HEATER - 3.9L/5.2L/
5.9L - REMOVAL......................7-45
ENGINE BLOCK HEATER - 5.9L DIESEL -
DESCRIPTION........................7-47
ENGINE BLOCK HEATER - 5.9L DIESEL -
INSTALLATION........................7-47
ENGINE BLOCK HEATER - 5.9L DIESEL -
OPERATION..........................7-47
ENGINE BLOCK HEATER - 5.9L DIESEL -
REMOVAL...........................7-47
ENGINE BLOCK HEATER - 8.0L -
DESCRIPTION........................7-46
ENGINE BLOCK HEATER - 8.0L -
INSTALLATION........................7-46
ENGINE BLOCK HEATER - 8.0L -
OPERATION..........................7-46
ENGINE BLOCK HEATER - 8.0L -
REMOVAL...........................7-46
ENGINE CONTROL MODULE -
INSTALLATION.......................8E-14
ENGINE CONTROL MODULE - REMOVAL . . 8E-14
ENGINE COOLANT TEMP SENSOR -
3.9L/5.2L/5.9L - DESCRIPTION...........7-48
ENGINE COOLANT TEMP SENSOR -
3.9L/5.2L/5.9L - INSTALLATION..........7-48
ENGINE COOLANT TEMP SENSOR -
3.9L/5.2L/5.9L - OPERATION.............7-48
ENGINE COOLANT TEMP SENSOR -
3.9L/5.2L/5.9L - REMOVAL..............7-48
ENGINE COOLANT THERMOSTAT -
3.9L/5.2L/5.9L - DESCRIPTION...........7-49
ENGINE COOLANT THERMOSTAT -
3.9L/5.2L/5.9L - INSTALLATION
..........7-50
ENGINE COOLANT THERMOSTAT -
3.9L/5.2L/5.9L - OPERATION
.............7-49
ENGINE COOLANT THERMOSTAT -
3.9L/5.2L/5.9L - REMOVAL
..............7-49
ENGINE COOLANT THERMOSTAT - 5.9L
DIESEL - DESCRIPTION
................7-54
ENGINE COOLANT THERMOSTAT - 5.9L
DIESEL - INSTALLATION
................7-55
ENGINE COOLANT THERMOSTAT - 5.9L
DIESEL - OPERATION
..................7-54
ENGINE COOLANT THERMOSTAT - 5.9L
DIESEL - REMOVAL
....................7-55
ENGINE COOLANT THERMOSTAT - 8.0L -
DESCRIPTION
........................7-52
ENGINE COOLANT THERMOSTAT - 8.0L -
INSTALLATION
........................7-53
ENGINE COOLANT THERMOSTAT - 8.0L -
OPERATION
..........................7-52
ENGINE COOLANT THERMOSTAT - 8.0L -
REMOVAL
...........................7-52
ENGINE DATA PLATE - DESCRIPTION
.....9-244
ENGINE DIAGNOSIS - INTRODUCTION -
DIAGNOSIS AND TESTING
.....9-118,9-173,9-3ENGINE DIAGNOSIS - MECHANICAL -
DIAGNOSIS AND TESTING.............9-232
ENGINE (FEDERAL ONLY - 2500 8.0L HD
AND 3500 5.9L& 8.0L MODELS)
MAINTENANCE SCHEDULES -
DESCRIPTION, HEAVY DUTY.............0-17
ENGINE FIRING ORDER, 3.9L V-6
ENGINE..............................8I-2
ENGINE FIRING ORDER, 5.2L/5.9L V-8
ENGINES............................8I-2
ENGINE OIL - DESCRIPTION...........0-3,0-4
ENGINE OIL - STANDARD PROCEDURE . . . 9-104,
9-160,9-217,9-47
ENGINE OIL LEAKS - DIAGNOSIS AND
TESTING.............9-104,9-160,9-215,9-47
ENGINE OIL PRESSURE - DIAGNOSIS
AND TESTING....9-104,9-160,9-215,9-295,9-47
ENGINE PERFORMANCE - INSPECTION . . . 30-16
ENGINE, SPECIAL TOOLS - 5.2L..........9-77
ENGINE, SPECIAL TOOLS - 5.9L.........9-134
ENGINE, SPECIAL TOOLS - 5.9L DIESEL . . 9-244
ENGINE, SPECIAL TOOLS - 8.0L.........9-188
ENGINE, SPECIFICATIONS - 3.9L.........9-14
ENGINE, SPECIFICATIONS - 5.2L.........9-72
ENGINE, SPECIFICATIONS - 5.9L........9-129
ENGINE, SPECIFICATIONS - 8.OL........9-184
ENGINE STARTER MOTOR -
DESCRIPTION.......................8F-39
ENGINE STARTER MOTOR -
INSTALLATION.......................8F-41
ENGINE STARTER MOTOR - OPERATION....8F-39
ENGINE STARTER MOTOR - REMOVAL....8F-40
ENGINE STARTER MOTOR RELAY -
DESCRIPTION.......................8F-42
ENGINE STARTER MOTOR RELAY -
INSTALLATION.......................8F-43
ENGINE STARTER MOTOR RELAY -
OPERATION.........................8F-42
ENGINE STARTER MOTOR RELAY -
REMOVAL..........................8F-43
ENGINE TEMPERATURE GAUGE -
DESCRIPTION.......................8J-19
ENGINE TEMPERATURE GAUGE -
OPERATION.........................8J-19
ENGINES - DESCRIPTION, COMPONENT
MONITORS - DIESEL..................25-18
ENGINES - DESCRIPTION, COMPONENT
MONITORS - GAS....................25-18
ENGINES - DESCRIPTION, FUEL
REQUIREMENTS - GAS..................0-1
ENGINES - DESCRIPTION, V-6/V-8
.......25-35
ENGINES - DIAGNOSIS AND TESTING,
PCV VALVE - V-6/V-8
..................25-36
ENGINES - ENGINE FIRING ORDER,
5.2L/5.9L V-8
.........................8I-2
ENGINES - FUEL SYSTEM PRESSURES,
DIESEL
............................14-58
ENGINES - IGNITION COIL RESISTANCE,
3.9L/5.2L/5.9L
........................8I-3
ENGINES - INSTALLATION, GAS
..........8P-4
ENGINES - OPERATION, GAS
...........25-18
ENGINES - OPERATION, NON-
MONITORED CIRCUITS - GAS
...........25-22
ENGINES - OPERATION, PCM - GAS
......8E-17
ENGINES - OPERATION, V-6/V-8
.........25-35
ENGINES - REMOVAL, GAS
..............8P-4
ENGINES - SPECIFICATIONS, FUEL
SYSTEM PRESSURE - GAS
..............14-4
ENGINES - STANDARD PROCEDURE,
DRAINING COOLING SYSTEM
3.9L/5.2L/5.9L/8.0L
....................7-15
ENGINES - STANDARD PROCEDURE,
REFILLING COOLING SYSTEM
3.9L/5.2L/5.9L/8.0L
....................7-15
ENGINES - VISUAL INSPECTION,
3.9L/5.2L/5.9L
.......................14-28
ENGINE-TO-BODY GROUND STRAP -
INSTALLATION
.......................8A-13
ENGINE-TO-BODY GROUND STRAP -
REMOVAL
..........................8A-13
ENTRY - INSPECTION, KEYLESS
.........30-11
ENTRY SEAT TRACK - INSTALLATION,
EASY
.............................23-142
ENTRY SEAT TRACK - REMOVAL, EASY
. . 23-142
ENTRY SYSTEM - DESCRIPTION,
REMOTE KEYLESS
....................8N-2ENTRY SYSTEM - DIAGNOSIS AND
TESTING, POWER LOCK & REMOTE
KEYLESS............................8N-4
ENTRY SYSTEM - OPERATION, REMOTE
KEYLESS............................8N-3
ENTRY TRANSMITTER - DESCRIPTION,
REMOTE KEYLESS....................8N-7
ENTRY TRANSMITTER - DIAGNOSIS AND
TESTING, REMOTE KEYLESS............8N-7
ENTRY TRANSMITTER - OPERATION,
REMOTE KEYLESS....................8N-7
EQUIPMENT - STANDARD PROCEDURE,
REFRIGERANT SYSTEM SERVICE........24-44
EQUIPMENT IDENTIFICATION PLATE -
DESCRIPTION.....................Intro.-12
ESCUTCHEON - INSTALLATION, HANDLE . . 23-63
ESCUTCHEON - REMOVAL, HANDLE......23-63
EVACUATE - STANDARD PROCEDURE,
REFRIGERANT SYSTEM...............24-45
EVAP SYSTEM - DESCRIPTION..........25-31
EVAP SYSTEM - TORQUE..............25-31
EVAPORATOR - DESCRIPTION, A/C.......24-52
EVAPORATOR - INSTALLATION, A/C......24-53
EVAPORATOR - OPERATION, A/C........24-53
EVAPORATOR - REMOVAL, A/C..........24-53
EVAP/PURGE SOLENOID - DESCRIPTION . . 25-32
EVAP/PURGE SOLENOID - INSTALLATION . 25-32
EVAP/PURGE SOLENOID - REMOVAL.....25-32
EXHAUST MANIFOLD - CLEANING . . 9-112,9-168,
9-225,9-304,9-55
EXHAUST MANIFOLD - DESCRIPTION....9-112,
9-168,9-224,9-55
EXHAUST MANIFOLD - INSPECTION.....9-112,
9-168,9-225,9-304,9-55
EXHAUST MANIFOLD - INSTALLATION . . . 9-113,
9-168,9-225,9-304,9-55
EXHAUST MANIFOLD - OPERATION . 9-112,9-168,
9-224,9-55
EXHAUST MANIFOLD - REMOVAL . . 9-112,9-168,
9-225,9-303,9-55
EXHAUST PIPE - 3.9L/5.2L/5.9L -
INSPECTION.........................11-7
EXHAUST PIPE - 3.9L/5.2L/5.9L -
INSTALLATION........................11-7
EXHAUST PIPE - 3.9L/5.2L/5.9L -
REMOVAL...........................11-7
EXHAUST PIPE - 5.9L DIESEL -
INSPECTION.........................11-9
EXHAUST PIPE - 5.9L DIESEL -
INSTALLATION.......................11-10
EXHAUST PIPE - 5.9L DIESEL -
REMOVAL...........................11-9
EXHAUST PIPE - 5.9L HEAVY DUTY/8.0L
- INSPECTION........................11-9
EXHAUST PIPE - 5.9L HEAVY DUTY/8.0L
- INSTALLATION......................11-9
EXHAUST PIPE - 5.9L HEAVY DUTY/8.0L
- REMOVAL..........................11-8
EXHAUST VENT - INSTALLATION........23-79
EXHAUST VENT - REMOVAL............23-79
EXHAUSTER - INSTALLATION, AIR.......23-77
EXHAUSTER - REMOVAL, AIR...........23-77
EXTENSION HOUSING BUSHING -
INSTALLATION....21-198,21-369,21-544,21-714
EXTENSION HOUSING BUSHING -
REMOVAL.......21-198,21-369,21-544,21-714
EXTENSION HOUSING BUSHING AND
SEAL - INSTALLATION....21-850,21-885,21-921
EXTENSION HOUSING BUSHING AND
SEAL - REMOVAL.......21-850,21-885,21-921
EXTENSION HOUSING SEAL -
INSTALLATION . . . 21-132,21-198,21-369,21-544,
21-715,21-87
EXTENSION HOUSING SEAL - REMOVAL . 21-132,
21-198,21-369,21-544,21-714,21-87
EXTERIOR - DESCRIPTION.............23-86
EXTERIOR - OPERATION...............23-86
EXTERIOR HANDLE - INSTALLATION.....23-70
EXTERIOR HANDLE - REMOVAL.........23-70
EXTERIOR NAME PLATES -
INSTALLATION
.......................23-89
EXTERIOR NAME PLATES - REMOVAL
....23-89
FAILURE - DIAGNOSIS AND TESTING,
CYLINDER HEAD GASKET
. 9-136,9-191,9-22,9-79
FAN - 3.9L/5.2L/5.9L/8.0L - CLEANING,
RADIATOR
...........................7-43
FAN - 3.9L/5.2L/5.9L/8.0L - INSPECTION,
RADIATOR
...........................7-43
BR/BEINDEX 13
Description Group-Page Description Group-Page Description Group-Page

FAN - 3.9L/5.2L/5.9L/8.0L -
INSTALLATION, RADIATOR..............7-43
FAN - 3.9L/5.2L/5.9L/8.0L - REMOVAL,
RADIATOR...........................7-42
FAN - 5.9L DIESEL - CLEANING,
RADIATOR...........................7-44
FAN - 5.9L DIESEL - INSPECTION,
RADIATOR...........................7-44
FAN - 5.9L DIESEL - INSTALLATION,
RADIATOR...........................7-45
FAN - 5.9L DIESEL - REMOVAL,
RADIATOR...........................7-44
FAN DRIVE - DIAGNOSIS AND TESTING,
VISCOUS........................7-56,7-58
FAN DRIVE VISCOUS CLUTCH -
3.9L/5.2L/5.9L/8.0L - DESCRIPTION.......7-56
FAN DRIVE VISCOUS CLUTCH -
3.9L/5.2L/5.9L/8.0L - OPERATION.........7-56
FAN DRIVE VISCOUS CLUTCH - 5.9L
DIESEL - DESCRIPTION................7-57
FAN DRIVE VISCOUS CLUTCH - 5.9L
DIESEL - OPERATION..................7-57
FASCIA - ADJUSTMENT, FRONT..........13-2
FASCIA - INSTALLATION, FRONT.........13-2
FASCIA - INSTALLATION, FRONT LOWER . . . 13-3
FASCIA - REMOVAL, FRONT.............13-2
FASCIA - REMOVAL, FRONT LOWER......13-3
FASCIA-SPORT - INSTALLATION, FRONT . . . 13-3
FASCIA-SPORT - REMOVAL, FRONT.......13-3
FASTENER IDENTIFICATION -
DESCRIPTION......................Intro.-3
FASTENER USAGE - DESCRIPTION......Intro.-6
FASTENERS - DESCRIPTION, PUSH-IN.....23-1
FEATURES - DESCRIPTION,
PROGRAMMABLE ELECTRONIC.........30-20
FEATURES - OPERATION,
PROGRAMMABLE ELECTRONIC.........30-20
FENDER - INSTALLATION, LEFT FRONT . . . 23-93
FENDER - INSTALLATION, REAR.........23-95
FENDER - INSTALLATION, RIGHT FRONT . . 23-94
FENDER - REMOVAL, LEFT FRONT.......23-92
FENDER - REMOVAL, REAR............23-95
FENDER - REMOVAL, RIGHT FRONT......23-94
FILL - STANDARD PROCEDURE,
TRANSMISSION . . . 21-201,21-372,21-547,21-718
FILL DOOR - INSTALLATION, FUEL.......23-95
FILL DOOR - REMOVAL, FUEL..........23-95
FILLER CAP - DESCRIPTION, FUEL.......25-33
FILLER CAP - OPERATION, FUEL........25-33
FILLER CAP - REMOVAL/INSTALLATION,
FUEL..............................25-33
FILTER - DESCRIPTION, PCV...........25-35
FILTER - INSTALLATION, AIR PUMP......25-29
FILTER - INSTALLATION, INLET..........14-22
FILTER - INSTALLATION, OIL . 9-105,9-161,9-218,
9-296,9-48
FILTER - REMOVAL, AIR PUMP.........25-29
FILTER - REMOVAL, INLET.............14-22
FILTER - REMOVAL, OIL.....9-105,9-161,9-218,
9-296,9-48
FILTER - STANDARD PROCEDURES,
WATER DRAINING AT FUEL............14-56
FILTER / WATER SEPARATOR -
DESCRIPTION, FUEL..................14-59
FILTER / WATER SEPARATOR -
INSTALLATION, FUEL.................14-61
FILTER / WATER SEPARATOR -
OPERATION, FUEL....................14-59
FILTER / WATER SEPARATOR -
REMOVAL, FUEL.....................14-60
FILTER REPLACEMENT - STANDARD
PROCEDURE, FLUID.....21-201,21-372,21-547,
21-717
FILTER/PRESSURE REGULATOR -
DESCRIPTION, FUEL...................14-5
FILTER/PRESSURE REGULATOR -
INSTALLATION, FUEL..................14-6
FILTER/PRESSURE REGULATOR -
OPERATION, FUEL.....................14-5
FILTER/PRESSURE REGULATOR -
REMOVAL, FUEL
......................14-5
FINAL STEPS - NEW VEHICLE
PREPARATION FORM
.................30-22
FINISH - DESCRIPTION, BASE
COAT/CLEAR COAT
..................23-129
FINISH - INSPECTION, FIT
........30-10,30-12
FINISH - OPERATION, BASE COAT/CLEAR
COAT
.............................23-129FIRING ORDER, 3.9L V-6 ENGINE -
ENGINE..............................8I-2
FIRING ORDER, 5.2L/5.9L V-8 ENGINES -
ENGINE..............................8I-2
FIRING ORDER, DIESEL - FUEL
INJECTOR..........................14-58
FIT AND FINISH - INSPECTION.....30-10,30-12
FITTING - DESCRIPTION, QUICK
CONNECT...........................14-22
FITTING - STANDARD PROCEDURE,
CONNECTING ROD BEARING . . 9-144,9-202,9-88
FITTING - STANDARD PROCEDURE,
CRANKSHAFT MAIN BEARING......9-146,9-90
FITTING - STANDARD PROCEDURE,
MAIN BEARING..................9-203,9-33
FITTING - STANDARD PROCEDURE,
PISTON...............9-153,9-208,9-40,9-97
FITTING - STANDARD PROCEDURE,
PISTON RING...............9-154,9-41,9-98
FITTING, CONNECTING ROD BEARINGS -
STANDARD PROCEDURE-CONNECTING
ROD BEARING........................9-31
FITTING PISTON RINGS - STANDARD
PROCEDURE........................9-211
FITTING, PISTON RINGS - STANDARD
PROCEDURE-PISTON RING.............9-288
FITTINGS - STANDARD PROCEDURES,
QUICK-CONNECT.....................14-22
FIXED ORIFICE TUBE - DIAGNOSIS AND
TESTING...........................24-54
FLAG - INSTALLATION, SIDE VIEW
MIRROR...........................23-74
FLAG - REMOVAL, SIDE VIEW MIRROR . . . 23-74
FLARING - STANDARD PROCEDURE,
DOUBLE INVERTED.....................5-8
FLARING - STANDARD PROCEDURE, ISO....5-8
FLASHER - DESCRIPTION, COMBINATION . . 8L-7
FLASHER - INSTALLATION,
COMBINATION........................8L-8
FLASHER - OPERATION, COMBINATION....8L-7
FLASHER - REMOVAL, COMBINATION.....8L-8
FLOOR MATS - INSTALLATION, CARPETS . 23-123
FLOOR MATS - REMOVAL, CARPETS....23-123
FLOOR SHIFT BOOT - INSTALLATION,
4WD .............................23-122
FLOOR SHIFT BOOT - REMOVAL, 4WD . . . 23-122
FLOOR STOWAGE TRAY -
INSTALLATION, REAR................23-121
FLOOR STOWAGE TRAY - REMOVAL,
REAR.............................23-121
FLOW - 3.9L/5.2L/5.9L ENGINE -
DESCRIPTION, COOLING SYSTEM.........7-1
FLOW - 5.9L DIESEL - DESCRIPTION,
COOLING SYSTEM.....................7-1
FLOW - DIAGNOSIS AND TESTING,
RADIATOR COOLANT..........7-59,7-61,7-63
FLOW AND PRESSURE - DIAGNOSIS
AND TESTING, POWER STEERING........19-4
FLUID - DESCRIPTION, AUTOMATIC
TRANSMISSION.......................0-5
FLUID - DESCRIPTION, TRANSFER CASE....0-5
FLUID - DIAGNOSIS AND TESTING,
CAUSES OF BURNT.....21-199,21-370,21-545,
21-715
FLUID - OPERATION, AUTOMATIC
TRANSMISSION.......................0-5
FLUID AND FILTER REPLACEMENT -
STANDARD PROCEDURE . 21-201,21-372,21-547,
21-717
FLUID CAPACITIES, SPECIFICATIONS.......0-6
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING....21-199,21-370,21-545,21-715
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING, BRAKE..................5-14
FLUID DRAIN AND REFILL - STANDARD
PROCEDURE...........21-851,21-885,21-922
FLUID INDICATOR - DESCRIPTION,
WASHER
...........................8J-35
FLUID INDICATOR - DIAGNOSIS AND
TESTING, WASHER
...................8J-36
FLUID INDICATOR - OPERATION,
WASHER
...........................8J-35
FLUID LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING
. . . 21-148,21-319,21-491,
21-662
FLUID LEVEL - DIAGNOSIS AND
TESTING, EFFECTS OF INCORRECT
.....21-199,
21-370,21-545,21-715FLUID LEVEL - STANDARD PROCEDURE,
BRAKE..............................5-14
FLUID LEVEL CHECK - STANDARD
PROCEDURE.....21-199,21-370,21-545,21-715
FLUID LEVEL SWITCH - DESCRIPTION,
WASHER............................8R-7
FLUID LEVEL SWITCH - INSTALLATION,
WASHER............................8R-8
FLUID LEVEL SWITCH - OPERATION,
WASHER............................8R-7
FLUID LEVEL SWITCH - REMOVAL,
WASHER............................8R-8
FLUID LEVELS - INSPECTION............30-4
FLUID RESERVOIR - INSTALLATION.......5-15
FLUID RESERVOIR - REMOVAL..........5-15
FLUID, SPECIFICATIONS - BRAKE.........5-15
FLUID TYPES - DESCRIPTION.............0-5
FLUSH MEASUREMENTS,
SPECIFICATIONS - BODY GAP..........23-56
FLUSHING - STANDARD PROCEDURE,
COOLING SYSTEM CLEANING/
REVERSE............................7-16
FLUSHING COOLER AND TUBES -
WITHOUT RADIATOR IN-TANK
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE.......7-80,7-83,7-86
FLUSHING COOLERS AND TUBES - WITH
RADIATOR IN-TANK TRANSMISSION
OIL COOLER - STANDARD
PROCEDURE.................7-79,7-83,7-85
FLUSHING POWER STEERING SYSTEM -
STANDARD PROCEDURE...............19-32
FLYWHEEL - ASSEMBLY................6-17
FLYWHEEL - DESCRIPTION..............6-16
FLYWHEEL - DIAGNOSIS AND TESTING....6-17
FLYWHEEL - DISASSEMBLY.............6-17
FLYWHEEL - OPERATION...............6-16
FOG LAMP - DIAGNOSIS AND TESTING....8L-9
FOG LAMP - INSTALLATION............8L-11
FOG LAMP - REMOVAL................8L-11
FOG LAMP UNIT - ADJUSTMENTS.......8L-12
FOG LAMP UNIT - INSTALLATION........8L-12
FOG LAMP UNIT - REMOVAL...........8L-11
FORE/AFT - ADJUSTMENT, FRONT DOOR . . 23-68
FORM, FINAL STEPS - NEW VEHICLE
PREPARATION.......................30-22
FORM-IN-PLACE GASKETS & SEALERS -
STANDARD PROCEDURE.....9-11,9-125,9-180,
9-237,9-68
FOUR-WHEEL DRIVE INDICATOR -
DIAGNOSIS AND TESTING..............8J-29
FRAME - DESCRIPTION.................13-6
FRAME - FRAME SERVICE..............13-6
FRAME - INSTALLATION, GRILLE........23-92
FRAME - REMOVAL, GRILLE............23-91
FRAME DIMENSION, SPECIFICATIONS.....13-7
FRAME SERVICE, FRAME...............13-6
FRONT - 2WD - DESCRIPTION.........2-7,2-8
FRONT - 4WD - DESCRIPTION...........2-14
FRONT - DESCRIPTION, CRANKSHAFT
OIL SEAL...................9-147,9-34,9-91
FRONT - INSTALLATION............5-14,5-27
FRONT - INSTALLATION...............22-12
FRONT - INSTALLATION, 1500/2500.......5-22
FRONT - INSTALLATION, 3500...........5-22
FRONT - INSTALLATION, CRANKSHAFT
OIL SEAL..............9-148,9-277,9-34,9-91
FRONT - INSTALLATION, PROPELLER
SHAFT...............................3-8
FRONT - OPERATION, CRANKSHAFT OIL
SEAL......................9-147,9-34,9-91
FRONT - REMOVAL................5-10,5-24
FRONT - REMOVAL, 1500/2500..........5-21
FRONT - REMOVAL, 3500...............5-22
FRONT - REMOVAL, CRANKSHAFT OIL
SEAL.................9-147,9-276,9-34,9-91
FRONT - REMOVAL, PROPELLER SHAFT....3-8
FRONT AIR DAM - INSTALLATION........13-2
FRONT AIR DAM - REMOVAL............13-1
FRONT AXLE - 216FBI - ADJUSTMENTS....3-17
FRONT AXLE - 216FBI - DESCRIPTION.....3-12
FRONT AXLE - 216FBI - INSTALLATION....3-17
FRONT AXLE - 216FBI - OPERATION......3-12
FRONT AXLE - 216FBI - REMOVAL
........3-16
FRONT AXLE - 248FBI - ADJUSTMENTS
....3-50
FRONT AXLE - 248FBI - DESCRIPTION
.....3-45
FRONT AXLE - 248FBI - INSTALLATION
....3-50
FRONT AXLE - 248FBI - OPERATION
......3-45
14 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

INJECTION PUMP TIMING - DIAGNOSIS
AND TESTING, FUEL..................14-66
INJECTION SYSTEM - DESCRIPTION, AIR . 25-25
INJECTION SYSTEM - DESCRIPTION,
DIESEL FUEL........................14-87
INJECTION SYSTEM - OPERATION, AIR . . . 25-27
INJECTION SYSTEM - TORQUE, AIR......25-28
INJECTOR - DESCRIPTION, FUEL . . . 14-53,14-93
INJECTOR - INSTALLATION, FUEL . . 14-53,14-98
INJECTOR - OPERATION, FUEL.....14-53,14-94
INJECTOR - REMOVAL, FUEL......14-53,14-96
INJECTOR FIRING ORDER, DIESEL -
FUEL..............................14-58
INJECTOR TEST - DIAGNOSIS AND
TESTING, FUEL.................14-53,14-95
INLET BAFFLE - INSTALLATION, HVAC
HOUSING...........................24-37
INLET BAFFLE - REMOVAL, HVAC
HOUSING...........................24-36
INLET FILTER - INSTALLATION..........14-22
INLET FILTER - REMOVAL..............14-22
INNER BELT WEATHERSTRIP -
INSTALLATION, FRONT DOOR..........23-154
INNER BELT WEATHERSTRIP -
REMOVAL, FRONT DOOR.............23-154
IN/OUT - ADJUSTMENT, FRONT DOOR....23-69
INPUT - DESCRIPTION, VEHICLE SPEED . . . 8P-1
INPUT - OPERATION, ASD SENSE - PCM . . . 8I-3
INSIDE HANDLE ACTUATOR -
INSTALLATION...................23-71,23-80
INSIDE HANDLE ACTUATOR - REMOVAL . . 23-71,
23-80
INSPECTION - DESCRIPTION, ROAD
TEST..............................30-15
INSPECTION - DIAGNOSIS AND
TESTING, WHEEL....................22-10
INSPECTION - INFORMATION LABELS -
STANDARD PROCEDURE...............30-22
INSPECTION, 3.9L/5.2L/5.9L ENGINES -
VISUAL............................14-28
INSPECTION, 8.0L ENGINE - VISUAL.....14-32
INSPECTION, A/C COMPRESSOR
CLUTCH............................24-16
INSPECTION, ACCUMULATOR . . . 21-192,21-363,
21-538,21-708
INSPECTION, AUTOMATIC
TRANSMISSION - 42RE...............21-165
INSPECTION, AUTOMATIC
TRANSMISSION - 44RE...............21-337
INSPECTION, AUTOMATIC
TRANSMISSION - 46RE...............21-510
INSPECTION, AUTOMATIC
TRANSMISSION - 47RE...............21-681
INSPECTION, BATTERY.................30-7
INSPECTION, BATTERY SYSTEM..........8F-5
INSPECTION, BODY SEALING...........30-10
INSPECTION, CAMSHAFT & BEARINGS
(IN BLOCK).........................9-272
INSPECTION, CATALYTIC CONVERTER -
3.9L/5.2L/5.9L........................11-5
INSPECTION, CATALYTIC CONVERTER -
5.9L HEAVY DUTY/8.0L.................11-7
INSPECTION, CHARGE AIR COOLER AND
PLUMBING.........................11-18
INSPECTION, COMPASS...............30-12
INSPECTION, CROSSHEADS............9-250
INSPECTION, CYLINDER HEAD....9-137,9-193,
9-23,9-250,9-80
INSPECTION, CYLINDER HEAD COVER(S) . 9-138,
9-194,9-24,9-253,9-81
INSPECTION, DISC BRAKE CALIPERS......5-12
INSPECTION, DOORS AND DOOR LOCKS . . 30-11
INSPECTION, DRUM...................5-33
INSPECTION, ENGINE BLOCK . 9-142,9-200,9-267,
9-28,9-86
INSPECTION, ENGINE PERFORMANCE....30-16
INSPECTION, EXHAUST MANIFOLD . 9-112,9-168,
9-225,9-304,9-55
INSPECTION, EXHAUST PIPE -
3.9L/5.2L/5.9L........................11-7
INSPECTION, EXHAUST PIPE - 5.9L
DIESEL
.............................11-9
INSPECTION, EXHAUST PIPE - 5.9L
HEAVY DUTY/8.0L
.....................11-9
INSPECTION, FIT AND FINISH
......30-10,30-12
INSPECTION, FLUID LEVELS
.............30-4
INSPECTION, FRONT CLUTCH
. . . 21-205,21-376,
21-550,21-721INSPECTION, FRONT SERVO....21-207,21-378,
21-553,21-723
INSPECTION, FUEL...................30-15
INSPECTION, GAUGES/WARNING LIGHTS . 30-19
INSPECTION, HEATER/AIR CONDITIONER . . 30-17
INSPECTION, HOOD LATCH/SAFETY
CATCH ..............................30-4
INSPECTION, HORN..................30-19
INSPECTION, INTAKE MANIFOLD . . . 9-110,9-166,
9-223,9-302,9-53
INSPECTION, INTAKE/EXHAUST VALVES
& SEATS ..............9-141,9-198,9-27,9-84
INSPECTION, KEYLESS ENTRY..........30-11
INSPECTION, LIGHTS AND SWITCHES....30-12
INSPECTION, LINES/HOSES.............30-6
INSPECTION, MANUAL - NV3500........21-15
INSPECTION, MEASURING TIMING
CHAIN STRETCH.......9-114,9-170,9-227,9-58
INSPECTION, MIRROR................30-19
INSPECTION, NEUTRAL SAFETY SWITCH . . 30-19
INSPECTION, OIL COOLER & LINES -
CLEANING..........................9-296
INSPECTION, OIL PAN . 9-106,9-162,9-219,9-297,
9-49
INSPECTION, OIL PRESSURE RELIEF
VALVE .............................9-297
INSPECTION, OIL PUMP....9-107,9-163,9-220,
9-299,9-50
INSPECTION, OIL PUMP . . 21-211,21-382,21-557,
21-728
INSPECTION, OTHER..................30-15
INSPECTION, OVERDRIVE UNIT . . 21-224,21-394,
21-569,21-741
INSPECTION, OVERRUNNING CLUTCH
CAM/OVERDRIVE PISTON RETAINER....21-236,
21-406,21-580,21-752
INSPECTION, PARKING BRAKE..........30-17
INSPECTION, PISTON & CONNECTING
ROD ............9-154,9-209,9-285,9-41,9-98
INSPECTION, PLANETARY GEARTRAIN/
OUTPUT SHAFT . . . 21-241,21-411,21-587,21-760
INSPECTION, PUSHRODS..............9-250
INSPECTION, RADIATOR - 3.9L/5.2L/5.9L . . . 7-61
INSPECTION, RADIATOR - 5.9L DIESEL....7-65
INSPECTION, RADIATOR - 8.0L..........7-62
INSPECTION, RADIATOR FAN -
3.9L/5.2L/5.9L/8.0L....................7-43
INSPECTION, RADIATOR FAN - 5.9L
DIESEL.............................7-44
INSPECTION, RADIATOR PRESSURE CAP . . . 7-66
INSPECTION, RADIO..................30-17
INSPECTION, REAR CLUTCH....21-248,21-419,
21-593,21-765
INSPECTION, RECEIVING...............30-3
INSPECTION, ROCKER ARM / ADJUSTER
ASSY..............................9-262
INSPECTION, SEAT BELTS, SHOULDER
BELTS, RETRACTORS AND HEAD
RESTRAINTS........................30-12
INSPECTION, SEATS..................30-13
INSPECTION, SERVICE BRAKES.........30-17
INSPECTION, SHIFT/CLUTCH INTERLOCK
SYSTEM............................30-19
INSPECTION, SOLID LIFTERS/TAPPETS . . . 9-281
INSPECTION, SPEED CONTROL.........30-17
INSPECTION, SQUEAKS, RATTLES AND
WIND NOISE........................30-15
INSPECTION, STEERING AND HANDLING
. . 30-15
INSPECTION, TAILPIPE - 3.9L/5.2L/5.9L
. . . 11-11
INSPECTION, TAILPIPE - 5.9L DIESEL
....11-12
INSPECTION, TAILPIPE - 5.9L HEAVY
DUTY/8.0L
..........................11-12
INSPECTION, TIRE PRESSURES
..........30-8
INSPECTION, TRANSFER CASE -
NV231HD
..........................21-832
INSPECTION, TRANSFER CASE -
NV241HD
..........................21-902
INSPECTION, TRANSFER CASE -
NV241LD
..........................21-867
INSPECTION, TRANSMISSION
.....21-109,21-64
INSPECTION, TRANSMISSION/TRANSFER
CASE
..............................30-15
INSPECTION, TRIP COMPUTER/
MAINTENANCE REMINDER
.............30-17
INSPECTION, TURBOCHARGER
..........11-16
INSPECTION, TURN AND EMERGENCY
SIGNALS
...........................30-19INSPECTION, VALVE BODY......21-293,21-465,
21-637,21-809
INSPECTION, VIBRATION DAMPER.......9-289
INSPECTION, VISUAL..................30-8
INSPECTION, WATER PUMP -
3.9L/5.2L/5.9L........................7-69
INSPECTION, WATER PUMP - 5.9L
DIESEL.............................7-73
INSPECTION, WATER PUMP - 8.0L........7-72
INSPECTION, WHEEL CYLINDERS........5-31
INSPECTION, WINDOWS, DOORS AND
LOCKS.............................30-14
INSPECTION WINDSHIELD WIPERS/
WASHERS, ROAD TEST................30-18
INSPECTION, WIPER & WASHER
SYSTEM............................8R-6
INSPECTION, WIRING..................30-7
INSTALLED - INSTALLATION, FRONT OIL
SEAL - FRONT COVER.................9-205
INSTALLED - REMOVAL, FRONT OIL
SEAL - FRONT COVER.................9-204
INSTRUMENT CLUSTER - ASSEMBLY.....8J-13
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-2
INSTRUMENT CLUSTER - DIAGNOSIS
AND TESTING........................8J-6
INSTRUMENT CLUSTER - DISASSEMBLY . . 8J-11
INSTRUMENT CLUSTER - INSTALLATION . . 8J-14
INSTRUMENT CLUSTER - OPERATION.....8J-3
INSTRUMENT CLUSTER - REMOVAL.....8J-10
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-10
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-9
INSTRUMENT PANEL DEMISTER DUCTS
- REMOVAL.........................24-37
INSTRUMENT PANEL DUCTS - REMOVAL . 24-37
INSTRUMENT PANEL SYSTEM -
DESCRIPTION......................23-104
INSTRUMENT PANEL SYSTEM -
INSTALLATION......................23-107
INSTRUMENT PANEL SYSTEM -
OPERATION........................23-105
INSTRUMENT PANEL SYSTEM -
REMOVAL.........................23-106
INSTRUMENT PANEL TOP COVER -
INSTALLATION......................23-115
INSTRUMENT PANEL TOP COVER -
REMOVAL.........................23-114
INTAKE AIR HEATER - DESCRIPTION....14-100
INTAKE AIR HEATER - INSTALLATION....14-101
INTAKE AIR HEATER - OPERATION......14-100
INTAKE AIR HEATER - REMOVAL.......14-100
INTAKE AIR HEATER RELAY -
DESCRIPTION......................14-101
INTAKE AIR HEATER RELAY -
INSTALLATION......................14-102
INTAKE AIR HEATER RELAY -
OPERATION........................14-102
INTAKE AIR HEATER RELAY - REMOVAL . 14-102
INTAKE MANIFOLD - CLEANING
....9-110,9-166,
9-223,9-302,9-53
INTAKE MANIFOLD - DESCRIPTION
. 9-109,9-165,
9-222,9-52
INTAKE MANIFOLD - INSPECTION
. . 9-110,9-166,
9-223,9-302,9-53
INTAKE MANIFOLD - INSTALLATION
.....9-111,
9-166,9-223,9-302,9-53
INTAKE MANIFOLD - OPERATION
. . 9-109,9-165,
9-52
INTAKE MANIFOLD - REMOVAL
....9-110,9-166,
9-222,9-301,9-53
INTAKE MANIFOLD LEAKAGE -
DIAGNOSIS AND TESTING
. . . 9-110,9-165,9-222,
9-53
INTAKE/EXHAUST VALVES & SEATS -
CLEANING
.............9-140,9-198,9-27,9-84
INTAKE/EXHAUST VALVES & SEATS -
DESCRIPTION
.....9-138,9-195,9-25,9-253,9-81
INTAKE/EXHAUST VALVES & SEATS -
INSPECTION
...........9-141,9-198,9-27,9-84
INTAKE/EXHAUST VALVES & SEATS -
INSTALLATION
.........9-141,9-260,9-28,9-85
INTAKE/EXHAUST VALVES & SEATS -
REMOVAL
.............9-140,9-258,9-27,9-84
INTAKE/EXHAUST VALVES & SEATS -
STANDARD PROCEDURE-
VALVES,GUIDES AND SPRINGS
.........9-253
BR/BEINDEX 19
Description Group-Page Description Group-Page Description Group-Page

INTAKE/EXHAUST VALVES & SEATS -
VALVE SERVICE......................9-195
IN-TANK TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLER AND TUBES - WITHOUT
RADIATOR...................7-80,7-83,7-86
IN-TANK TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLERS AND TUBES - WITH
RADIATOR...................7-79,7-83,7-85
INTERIOR - CAUTION................23-118
INTERLOCK SYSTEM - INSPECTION,
SHIFT/CLUTCH.......................30-19
INTERMEDIATE - INSTALLATION, AXLE
SHAFTS.............................3-28
INTERMEDIATE - REMOVAL, AXLE
SHAFTS.............................3-28
INTERMEDIATE AXLE - INSTALLATION.....3-61
INTERMEDIATE AXLE - REMOVAL.........3-60
INTERNATIONAL SYMBOLS -
DESCRIPTION......................Intro.-6
INTERNATIONAL SYMBOLS -
DESCRIPTION.........................0-3
INTRODUCTION - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS . . 9-118,9-173,9-3
INTRODUCTION - DIAGNOSIS AND
TESTING-ENGINE DIAGNOSIS............9-61
INVERTED FLARING - STANDARD
PROCEDURE, DOUBLE..................5-8
IOD FUSE - DESCRIPTION...........8W-97-4
IOD FUSE - INSTALLATION...........8W-97-5
IOD FUSE - OPERATION.............8W-97-5
IOD FUSE - REMOVAL................8W-97-5
ISO FLARING - STANDARD PROCEDURE....5-8
ITEMS - INSTALLATION, SHIPPED LOOSE . 30-14
JOINT - DIAGNOSIS AND TESTING,
LOWER BALL........................2-10
JOINT - DIAGNOSIS AND TESTING,
UPPER BALL.........................2-12
JOINT - INSTALLATION, LOWER BALL.....2-25
JOINT - INSTALLATION, UPPER BALL.....2-25
JOINT MOLDING - INSTALLATION, ROOF . . 23-91
JOINT MOLDING - REMOVAL, ROOF......23-91
JOINTS - DISASSEMBLY, SINGLE
CARDAN UNIVERSAL..................3-11
JOINTS - INSTALLATION, SINGLE
CARDAN UNIVERSAL..............3-34,3-66
JOINTS - REMOVAL, SINGLE CARDAN
UNIVERSAL......................3-33,3-65
JOUNCE BUMPER - DESCRIPTION.....2-28,2-9
JOUNCE BUMPER - OPERATION.......2-28,2-9
JOURNAL CLEARANCE - STANDARD
PROCEDURE, CONNECTING ROD
BEARING AND CRANKSHAFT...........9-274
JUMP STARTING - STANDARD
PROCEDURE.........................0-27
JUNCTION BLOCK - DESCRIPTION.....8W-97-6
JUNCTION BLOCK - INSTALLATION....8W-97-7
JUNCTION BLOCK - OPERATION......8W-97-6
JUNCTION BLOCK - REMOVAL........8W-97-6
KEEPER - INSTALLATION, BACKLITE
LATCH ............................23-146
KEEPER - REMOVAL, BACKLITE LATCH . . 23-146
KEY LOCK CYLINDER - DIAGNOSIS AND
TESTING, IGNITION SWITCH............19-10
KEY-IN IGNITION SWITCH -
DESCRIPTION........................19-9
KEYLESS ENTRY - INSPECTION.........30-11
KEYLESS ENTRY SYSTEM -
DESCRIPTION, REMOTE................8N-2
KEYLESS ENTRY SYSTEM - DIAGNOSIS
AND TESTING, POWER LOCK &
REMOTE............................8N-4
KEYLESS ENTRY SYSTEM - OPERATION,
REMOTE............................8N-3
KEYLESS ENTRY TRANSMITTER -
DESCRIPTION, REMOTE................8N-7
KEYLESS ENTRY TRANSMITTER -
DIAGNOSIS AND TESTING, REMOTE......8N-7
KEYLESS ENTRY TRANSMITTER -
OPERATION, REMOTE..................8N-7
KNOB - INSTALLATION, TURNING LOOP
HEIGHT ADJUSTER
...................8O-30
KNOB - REMOVAL, TURNING LOOP
HEIGHT ADJUSTER
...................8O-30
KNUCKLE - DESCRIPTION
............2-20,2-9
KNUCKLE - INSTALLATION
..........2-10,2-20
KNUCKLE - OPERATION
............2-10,2-20KNUCKLE - REMOVAL..............2-10,2-20
LABEL - DESCRIPTION, VECI.........Intro.-10
LABEL - DESCRIPTION, VEHICLE SAFETY
CERTIFICATION....................Intro.-12
LABEL - OPERATION, VECI...........Intro.-10
LABELS - STANDARD PROCEDURE,
INSPECTION - INFORMATION...........30-22
LAMP - DESCRIPTION, READING........8L-36
LAMP - DESCRIPTION, TAIL............8L-29
LAMP - DIAGNOSIS AND TESTING, FOG . . . 8L-9
LAMP - INSTALLATION, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP - INSTALLATION, CLEARANCE......8L-6
LAMP - INSTALLATION, DOME..........8L-33
LAMP - INSTALLATION, FOG............8L-11
LAMP - INSTALLATION, LICENSE PLATE . . 8L-22
LAMP - INSTALLATION, MARKER........8L-23
LAMP - INSTALLATION, OUTBOARD
IDENTIFICATION.....................8L-29
LAMP - INSTALLATION, PARK/TURN
SIGNAL............................8L-29
LAMP - INSTALLATION, READING........8L-36
LAMP - INSTALLATION, TAIL...........8L-30
LAMP - INSTALLATION, UNDERHOOD....8L-32
LAMP - INSTALLATION, VANITY.........8L-37
LAMP - OPERATION, READING..........8L-36
LAMP - OPERATION, TAIL..............8L-29
LAMP - REMOVAL, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP - REMOVAL, CLEARANCE..........8L-6
LAMP - REMOVAL, DOME..............8L-33
LAMP - REMOVAL, FOG...............8L-11
LAMP - REMOVAL, LICENSE PLATE......8L-22
LAMP - REMOVAL, MARKER...........8L-22
LAMP - REMOVAL, OUTBOARD
IDENTIFICATION.....................8L-28
LAMP - REMOVAL, PARK/TURN SIGNAL . . 8L-29
LAMP - REMOVAL, READING...........8L-36
LAMP - REMOVAL, TAIL...............8L-29
LAMP - REMOVAL, UNDERHOOD........8L-31
LAMP - REMOVAL, VANITY.............8L-37
LAMP AND SWITCH - INSTALLATION,
GLOVE BOX.........................8L-35
LAMP AND SWITCH - REMOVAL, GLOVE
BOX ...............................8L-35
LAMP (MIL) - DESCRIPTION,
MALFUNCTION INDICATOR.............8J-24
LAMP (MIL) - OPERATION,
MALFUNCTION INDICATOR.............8J-24
LAMP MODULE - DESCRIPTION,
DAYTIME RUNNING....................8L-9
LAMP MODULE - INSTALLATION,
DAYTIME RUNNING....................8L-9
LAMP MODULE - OPERATION, DAYTIME
RUNNING............................8L-9
LAMP MODULE - REMOVAL, DAYTIME
RUNNING............................8L-9
LAMP SWITCH - DESCRIPTION, BRAKE....8L-4
LAMP SWITCH - DIAGNOSIS AND
TESTING, BRAKE......................8L-5
LAMP SWITCH - INSTALLATION, BRAKE . . . 8L-5
LAMP SWITCH - OPERATION, BRAKE......8L-4
LAMP SWITCH - REMOVAL, BRAKE.......8L-5
LAMP UNIT - ADJUSTMENTS, FOG.......8L-12
LAMP UNIT - INSTALLATION, CENTER
HIGH MOUNTED STOP.................8L-6
LAMP UNIT - INSTALLATION, FOG.......8L-12
LAMP UNIT - INSTALLATION, LICENSE
PLATE .............................8L-22
LAMP UNIT - INSTALLATION, PARK/
TURN SIGNAL.......................8L-29
LAMP UNIT - INSTALLATION, TAIL.......8L-30
LAMP UNIT - INSTALLATION,
UNDERHOOD........................8L-32
LAMP UNIT - REMOVAL, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP UNIT - REMOVAL, FOG...........8L-11
LAMP UNIT - REMOVAL, LICENSE PLATE . . 8L-22
LAMP UNIT - REMOVAL, PARK/TURN
SIGNAL............................8L-29
LAMP UNIT - REMOVAL, TAIL...........8L-30
LAMP UNIT - REMOVAL, UNDERHOOD . . . 8L-32
LASH ADJUSTMENT AND VERIFICATION
- STANDARD PROCEDURE, VALVE
.......9-256
LATCH - ADJUSTMENT
...............23-100
LATCH - ADJUSTMENT, FRONT DOOR
....23-72
LATCH - INSTALLATION
....23-100,23-64,23-72
LATCH - INSTALLATION, SAFETY
.......23-102LATCH - LOWER - INSTALLATION........23-80
LATCH - LOWER - REMOVAL...........23-80
LATCH - REMOVAL........23-100,23-64,23-72
LATCH - REMOVAL, SAFETY...........23-102
LATCH - UPPER - INSTALLATION........23-81
LATCH - UPPER - REMOVAL............23-81
LATCH AND KEEPER - INSTALLATION,
BACKLITE.........................23-146
LATCH AND KEEPER - REMOVAL,
BACKLITE.........................23-146
LATCH HANDLE - INSTALLATION........23-65
LATCH HANDLE - REMOVAL............23-65
LATCH RELEASE CABLE - INSTALLATION . 23-101
LATCH RELEASE CABLE - REMOVAL....23-101
LATCH STRIKER - ADJUSTMENT.......23-102
LATCH STRIKER - INSTALLATION . 23-102,23-65,
23-73
LATCH STRIKER - INSTALLATION, GLOVE
BOX ..............................23-113
LATCH STRIKER - LOWER -
INSTALLATION.......................23-82
LATCH STRIKER - LOWER - REMOVAL....23-82
LATCH STRIKER - REMOVAL.....23-102,23-65,
23-73
LATCH STRIKER - REMOVAL, GLOVE
BOX ..............................23-113
LATCH STRIKER - UPPER -
INSTALLATION.......................23-82
LATCH STRIKER - UPPER - REMOVAL....23-82
LATCH/SAFETY CATCH - INSPECTION,
HOOD..............................30-4
LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING FLUID . . . 21-148,21-319,
21-491,21-662
LEAK DETECTION PUMP - DESCRIPTION . . 25-33
LEAK DETECTION PUMP - INSTALLATION . 25-34
LEAK DETECTION PUMP - REMOVAL.....25-34
LEAK DOWN TEST - DIAGNOSIS AND
TESTING, FUEL PRESSURE..............14-2
LEAKAGE - DIAGNOSIS AND TESTING,
CYLINDER COMBUSTION PRESSURE....9-124,
9-179,9-67,9-9
LEAKAGE - DIAGNOSIS AND TESTING,
INTAKE MANIFOLD.....9-110,9-165,9-222,9-53
LEAKAGE - DIAGNOSIS AND TESTING,
POWER STEERING GEAR..............19-14
LEAKAGE - DIAGNOSIS AND TESTING,
PUMP.............................19-31
LEAKS - DIAGNOSIS AND TESTING,
COOLING SYSTEM.....................7-5
LEAKS - DIAGNOSIS AND TESTING,
ENGINE OIL...........9-104,9-160,9-215,9-47
LEAKS - DIAGNOSIS AND TESTING,
HIGH-PRESSURE FUEL LINE............14-74
LEAKS - DIAGNOSIS AND TESTING,
REAR SEAL AREA.....................9-10
LEAKS - DIAGNOSIS AND TESTING,
REFRIGERANT SYSTEM...............24-43
LEAKS - DIAGNOSIS AND TESTING,
WATER .............................23-2
LEAKS - STANDARD PROCEDURES,
REPAIRING..........................22-8
LEFT FRONT FENDER - INSTALLATION....23-93
LEFT FRONT FENDER - REMOVAL.......23-92
LEVEL - DIAGNOSIS AND TESTING,
EFFECTS OF INCORRECT FLUID . . 21-199,21-370,
21-545,21-715
LEVEL - STANDARD PROCEDURE,
BRAKE FLUID........................5-14
LEVEL - STANDARD PROCEDURE,
CHECKING BATTERY ELECTROLYTE.......8F-8
LEVEL - STANDARD PROCEDURE,
REFRIGERANT OIL...................24-57
LEVEL CHECK - STANDARD
PROCEDURE, COOLANT................7-16
LEVEL CHECK - STANDARD
PROCEDURE, FLUID.....21-199,21-370,21-545,
21-715
LEVEL, OIL - STANDARD PROCEDURE-
ENGINE OIL
.........................9-295
LEVEL SENDING UNIT / SENSOR -
DESCRIPTION, FUEL
..............14-7,14-73
LEVEL SENDING UNIT / SENSOR -
INSTALLATION, FUEL
..................14-9
LEVEL SENDING UNIT / SENSOR -
OPERATION, FUEL
................14-7,14-73
LEVEL SENDING UNIT / SENSOR -
REMOVAL, FUEL
......................14-8
20 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

MOUNTED - INSTALLATION, SIDE VIEW
MIRROR - LOW......................23-98
MOUNTED - REMOVAL, SIDE VIEW
MIRROR - LOW......................23-98
MOUNTED STOP LAMP - INSTALLATION,
CENTER HIGH........................8L-6
MOUNTED STOP LAMP - REMOVAL,
CENTER HIGH........................8L-6
MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER HIGH...........8L-6
MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER HIGH...............8L-6
MOUNTING - STANDARD PROCEDURES,
MATCH .............................22-2
MUFFLER - 3.9L/5.2L/5.9L/8.0L -
INSTALLATION.......................11-11
MUFFLER - 3.9L/5.2L/5.9L/8.0L -
REMOVAL..........................11-10
MUFFLER - 5.9L DIESEL - INSTALLATION . 11-11
MUFFLER - 5.9L DIESEL - REMOVAL.....11-11
MULTI-FUNCTION SWITCH -
DESCRIPTION.......................8L-23
MULTI-FUNCTION SWITCH - DIAGNOSIS
AND TESTING.......................8L-25
MULTI-FUNCTION SWITCH -
INSTALLATION.......................8L-28
MULTI-FUNCTION SWITCH - OPERATION . . 8L-24
MULTI-FUNCTION SWITCH - REMOVAL . . . 8L-27
NAME PLATES - INSTALLATION,
EXTERIOR..........................23-89
NAME PLATES - REMOVAL, EXTERIOR....23-89
NECK SEAL - DIAGNOSIS AND TESTING,
RADIATOR CAP-TO-FILLER..............7-66
NEGATIVE CABLE INSTALLATION,
GASOLINE..........................8F-24
NEGATIVE CABLE REMOVAL, GASOLINE . . . 8F-23
NEUTRAL SAFETY SWITCH -
INSPECTION........................30-19
NEW VEHICLE PREPARATION -
DESCRIPTION, THE IMPORTANCE OF
CAREFUL............................30-1
NEW VEHICLE PREPARATION FORM,
FINAL STEPS........................30-22
NIGHT MIRROR - DESCRIPTION,
AUTOMATIC DAY.....................8N-10
NIGHT MIRROR - INSTALLATION,
AUTOMATIC DAY.....................8N-12
NIGHT MIRROR - OPERATION,
AUTOMATIC DAY.....................8N-11
NIGHT MIRROR - REMOVAL,
AUTOMATIC DAY.....................8N-12
NOISE - DIAGNOSIS AND TESTING,
WIND...............................23-3
NOISE - INSPECTION, SQUEAKS,
RATTLES AND WIND..................30-15
NOISE OR VIBRATION - DIAGNOSIS AND
TESTING, TIRE.......................22-8
NOISE SUPPRESSION COMPONENTS -
DESCRIPTION, RADIO.................8A-12
NOISE SUPPRESSION COMPONENTS -
DIAGNOSIS AND TESTING, RADIO.......8A-12
NON-DEPLOYED AIRBAGS - STANDARD
PROCEDURE, HANDLING...............8O-4
NON-MONITORED CIRCUITS - DIESEL -
OPERATION.........................25-23
NON-MONITORED CIRCUITS - GAS
ENGINES - OPERATION................25-22
NOZZLE - DESCRIPTION, WASHER.......8R-9
NOZZLE - INSTALLATION, WASHER.......8R-9
NOZZLE - OPERATION, WASHER.........8R-9
NOZZLE - REMOVAL, WASHER...........8R-9
NUMBER - DESCRIPTION, VEHICLE
IDENTIFICATION...................Intro.-10
NV231HD - ASSEMBLY, TRANSFER CASE . 21-834
NV231HD - CLEANING, TRANSFER CASE . 21-831
NV231HD - DESCRIPTION, TRANSFER
CASE.............................21-820
NV231HD - DISASSEMBLY, TRANSFER
CASE.............................21-822
NV231HD - INSPECTION, TRANSFER
CASE.............................21-832
NV231HD - INSTALLATION, TRANSFER
CASE
.............................21-847
NV231HD - OPERATION, TRANSFER
CASE
.............................21-820
NV231HD - REMOVAL, TRANSFER CASE
. 21-822
NV231HD - TRANSFER CASE
..........21-849
NV241HD - ASSEMBLY, TRANSFER CASE
. 21-904NV241HD - CLEANING, TRANSFER CASE . 21-902
NV241HD - DESCRIPTION, TRANSFER
CASE.............................21-890
NV241HD - DISASSEMBLY, TRANSFER
CASE.............................21-894
NV241HD - INSPECTION, TRANSFER
CASE.............................21-902
NV241HD - INSTALLATION, TRANSFER
CASE.............................21-919
NV241HD - OPERATION, TRANSFER
CASE.............................21-892
NV241HD - REMOVAL, TRANSFER CASE . 21-894
NV241HD - TRANSFER CASE..........21-920
NV241LD - ASSEMBLY, TRANSFER CASE . 21-869
NV241LD - CLEANING, TRANSFER CASE . 21-866
NV241LD - DESCRIPTION, TRANSFER
CASE.............................21-855
NV241LD - DISASSEMBLY, TRANSFER
CASE.............................21-858
NV241LD - INSPECTION, TRANSFER
CASE.............................21-867
NV241LD - INSTALLATION, TRANSFER
CASE.............................21-882
NV241LD - OPERATION, TRANSFER
CASE.............................21-855
NV241LD - REMOVAL, TRANSFER CASE . 21-858
NV241LD - TRANSFER CASE...........21-884
NV3500 - ASSEMBLY, MANUAL.........21-17
NV3500 - CLEANING, MANUAL..........21-15
NV3500 - DESCRIPTION, MANUAL........21-1
NV3500 - DISASSEMBLY, MANUAL........21-5
NV3500 - INSPECTION, MANUAL........21-15
NV3500 - INSTALLATION, MANUAL......21-40
NV3500 - MANUAL...................21-41
NV3500 - OPERATION, MANUAL..........21-1
NV3500 - REMOVAL, MANUAL...........21-3
NV4500 - ASSEMBLY, MANUAL.........21-65
NV4500 - CLEANING, MANUAL..........21-64
NV4500 - DESCRIPTION, MANUAL.......21-44
NV4500 - DISASSEMBLY, MANUAL.......21-48
NV4500 - INSTALLATION, MANUAL......21-82
NV4500 - MANUAL...................21-83
NV4500 - OPERATION, MANUAL.........21-46
NV4500 - REMOVAL, MANUAL..........21-47
NV4500 - SPECIFICATIONS.............21-83
NV5600 - ASSEMBLY, MANUAL........21-110
NV5600 - DESCRIPTION, MANUAL.......21-91
NV5600 - DISASSEMBLY, MANUAL.......21-95
NV5600 - INSTALLATION, MANUAL.....21-125
NV5600 - OPERATION, MANUAL.........21-93
NV5600 - REMOVAL, MANUAL..........21-94
NV5600 - SPECIFICATIONS............21-126
NV5600 MANUAL TRANSMISSION,
SPECIAL TOOLS....................21-127
O2 SENSOR - DESCRIPTION............14-46
O2 SENSOR - INSTALLATION...........14-48
O2 SENSOR - OPERATION.............14-46
O2 SENSOR - REMOVAL...............14-47
ODOMETER - DESCRIPTION............8J-24
ODOMETER - OPERATION..............8J-25
OFF INDICATOR - DESCRIPTION,
OVERDRIVE.........................8J-27
OFF INDICATOR - OPERATION,
OVERDRIVE.........................8J-27
OFF SWITCH - DESCRIPTION,
OVERDRIVE........................21-215
OFF SWITCH - INSTALLATION,
OVERDRIVE........................21-215
OFF SWITCH - OPERATION, OVERDRIVE . 21-215
OFF SWITCH - REMOVAL, OVERDRIVE . . . 21-215
OIL - DESCRIPTION, ENGINE..........0-3,0-4
OIL - DESCRIPTION, REFRIGERANT......24-56
OIL - OPERATION, REFRIGERANT........24-56
OIL - STANDARD PROCEDURE, ENGINE . . 9-104,
9-160,9-217,9-47
OIL - STANDARD PROCEDURE-ENGINE
OIL LEVEL..........................9-295
OIL - STANDARD PROCEDURE-ENGINE
OIL SERVICE........................9-295
OIL COOLER - INSTALLATION, AIR TO
.....7-88
OIL COOLER & LINES - CLEANING AND
INSPECTION
........................9-296
OIL COOLER - REMOVAL, AIR TO
.........7-87
OIL COOLER - REMOVAL, WATER TO
......7-87
OIL COOLER - STANDARD PROCEDURE,
FLUSHING COOLER AND TUBES -
WITHOUT RADIATOR IN-TANK
TRANSMISSION
..............7-80,7-83,7-86OIL COOLER - STANDARD PROCEDURE,
FLUSHING COOLERS AND TUBES -
WITH RADIATOR IN-TANK
TRANSMISSION..............7-79,7-83,7-85
OIL FILTER - INSTALLATION . 9-105,9-161,9-218,
9-296,9-48
OIL FILTER - REMOVAL.....9-105,9-161,9-218,
9-296,9-48
OIL LEAKS - DIAGNOSIS AND TESTING,
ENGINE..............9-104,9-160,9-215,9-47
OIL LEVEL - STANDARD PROCEDURE,
REFRIGERANT.......................24-57
OIL LEVEL, OIL - STANDARD
PROCEDURE-ENGINE.................9-295
OIL PAN - CLEANING . . 9-106,9-162,9-218,9-297,
9-49
OIL PAN - INSPECTION.....9-106,9-162,9-219,
9-297,9-49
OIL PAN - INSTALLATION . . . 9-106,9-162,9-219,
9-297,9-49
OIL PAN - REMOVAL . . 9-105,9-161,9-218,9-296,
9-48
OIL PRESSURE - DIAGNOSIS AND
TESTING, ENGINE . 9-104,9-160,9-215,9-295,9-47
OIL PRESSURE GAUGE - DESCRIPTION . . . 8J-25
OIL PRESSURE GAUGE - OPERATION.....8J-26
OIL PRESSURE RELIEF VALVE -
CLEANING..........................9-297
OIL PRESSURE RELIEF VALVE -
INSPECTION........................9-297
OIL PRESSURE RELIEF VALVE -
INSTALLATION.......................9-298
OIL PRESSURE RELIEF VALVE -
REMOVAL............................9-297
OIL PRESSURE SENSOR/SWITCH -
DESCRIPTION...................9-298,9-49
OIL PRESSURE SENSOR/SWITCH -
INSTALLATION.......................9-299
OIL PRESSURE SENSOR/SWITCH -
OPERATION.....................9-298,9-49
OIL PRESSURE SENSOR/SWITCH -
REMOVAL..........................9-298
OIL PUMP - ASSEMBLE..........9-109,9-165
OIL PUMP - ASSEMBLY................9-51
OIL PUMP - ASSEMBLY . . 21-212,21-382,21-558,
21-729
OIL PUMP - CLEANING.......9-220,9-299,9-50
OIL PUMP - CLEANING . . 21-211,21-381,21-557,
21-728
OIL PUMP - DESCRIPTION......21-208,21-379,
21-554,21-724
OIL PUMP - DISASSEMBLE . . . 9-107,9-163,9-50
OIL PUMP - DISASSEMBLY.....21-209,21-380,
21-555,21-726
OIL PUMP - INSPECTION....9-107,9-163,9-220,
9-299,9-50
OIL PUMP - INSPECTION . 21-211,21-382,21-557,
21-728
OIL PUMP - INSTALLATION . . 9-109,9-165,9-221,
9-300,9-52
OIL PUMP - OPERATION . 21-208,21-379,21-554,
21-724
OIL PUMP - REMOVAL......9-107,9-162,9-219,
9-299,9-50
OIL PUMP VOLUME CHECK - STANDARD
PROCEDURE.....21-209,21-379,21-554,21-724
OIL SEAL - FRONT - DESCRIPTION,
CRANKSHAFT...............9-147,9-34,9-91
OIL SEAL - FRONT - INSTALLATION,
CRANKSHAFT..........9-148,9-277,9-34,9-91
OIL SEAL - FRONT - OPERATION,
CRANKSHAFT...............9-147,9-34,9-91
OIL SEAL - FRONT - REMOVAL,
CRANKSHAFT..........9-147,9-276,9-34,9-91
OIL SEAL - FRONT COVER INSTALLED -
INSTALLATION, FRONT................9-205
OIL SEAL - FRONT COVER INSTALLED -
REMOVAL, FRONT....................9-204
OIL SEAL - FRONT COVER REMOVED -
INSTALLATION, FRONT
................9-205
OIL SEAL - FRONT COVER REMOVED -
REMOVAL, FRONT
....................9-204
OIL SEAL - REAR - DESCRIPTION,
CRANKSHAFT
...............9-148,9-34,9-91
OIL SEAL - REAR - INSTALLATION,
CRANKSHAFT
.....9-149,9-206,9-278,9-35,9-92
OIL SEAL - REAR - OPERATION,
CRANKSHAFT
...............9-148,9-34,9-92
BR/BEINDEX 23
Description Group-Page Description Group-Page Description Group-Page