turbo DODGE RAM 2001 Service Owner's Guide
[x] Cancel search | Manufacturer: DODGE, Model Year: 2001, Model line: RAM, Model: DODGE RAM 2001Pages: 2889, PDF Size: 68.07 MB
Page 1473 of 2889
(3) Remove the front support bracket.
(4) Discharge the A/C system (Refer to 24 - HEAT-
ING & AIR CONDITIONING/PLUMBING - STAN-
DARD PROCEDURE) and remove the A/C condenser
(Refer to 24 - HEATING & AIR CONDITIONING/
PLUMBING/A/C CONDENSER - REMOVAL) (Fig.
29) (if A/C equipped) .
(5) Remove the transmission auxiliary cooler (Fig.
29) (Refer to 7 - COOLING/TRANSMISSION/TRANS
COOLER - REMOVAL).
(6) Remove the boost tubes from the charge air
cooler (Fig. 30).
(7) Remove the charge air cooler bolts. Pivot the
charge air cooler forward and up to remove.
CLEANING
CAUTION: Do not use caustic cleaners to clean the
charge air cooler. Damage to the charge air cooler
will result.
NOTE: If internal debris cannot be removed from
the cooler, the charge air cooler MUST be replaced.
(1) If the engine experiences a turbocharger failure
or any other situation where oil or debris get into the
charge air cooler, the charge air cooler must be
cleaned internally.
(2) Position the charge air cooler so the inlet and
outlet tubes are vertical.
(3) Flush the cooler internally with solvent in the
direction opposite of normal air flow.(4) Shake the cooler and lightly tap on the end
tanks with a rubber mallet to dislodge trapped
debris.
(5) Continue flushing until all debris or oil are
removed.
(6) Rinse the cooler with hot soapy water to
remove any remaining solvent.
(7) Rinse thoroughly with clean water and blow
dry with compressed air.
INSPECTION
Visually inspect the charge air cooler for cracks,
holes, or damage. Inspect the tubes, fins, and welds
for tears, breaks, or other damage. Replace the
charge air cooler if damage is found.
Pressure test the charge air cooler, using Charge
Air Cooler Tester Kit #3824556. This kit is available
through CumminstService Products. Instructions
are provided with the kit.
INSTALLATION
(1) Position the charge air cooler. Install the bolts
and tighten to 2 N´m (17 in. lbs.) torque.
Fig. 29 Condenser and Transmission Auxiliary
Cooler
1 - A/C CONDENSOR
2 - TRANSMISSION COOLER
3 - INTERCOOLER
Fig. 30 Air Intake System Tubes
1 - CLAMP
2 - INTERCOOLER INLET DUCT
3 - CLAMP
4 - VALVE COVER
5 - AIR INLET HOUSING
6 - CLAMP
7 - INTERCOOLER OUTLET DUCT
8 - CLAMP
9 - INTERCOOLER
11 - 18 EXHAUST SYSTEMBR/BE
CHARGE AIR COOLER AND PLUMBING (Continued)
Page 1541 of 2889
FUEL DELIVERY - DIESEL
TABLE OF CONTENTS
page page
FUEL DELIVERY - DIESEL
DESCRIPTION...........................54
OPERATION.............................56
DIAGNOSIS AND TESTING.................56
AIR IN FUEL SYSTEM...................56
FUEL SUPPLY RESTRICTIONS............56
STANDARD PROCEDURE..................56
WATER DRAINING AT FUEL FILTER........56
CLEANING FUEL SYSTEM PARTS..........57
AIR BLEED............................57
SPECIFICATIONS........................58
SPECIAL TOOLS.........................59
FUEL FILTER / WATER SEPARATOR
DESCRIPTION...........................59
OPERATION.............................59
REMOVAL..............................60
INSTALLATION...........................61
FUEL HEATER
DESCRIPTION...........................62
OPERATION.............................62
DIAGNOSIS AND TESTING.................62
FUEL HEATER.........................62
REMOVAL..............................63
FUEL HEATER RELAY
DESCRIPTION...........................63
OPERATION.............................63
DIAGNOSIS AND TESTING.................64
FUEL HEATER RELAY...................64
REMOVAL..............................65
INSTALLATION...........................65
FUEL INJECTION PUMP
DESCRIPTION...........................65
OPERATION.............................66
DIAGNOSIS AND TESTING.................66
FUEL INJECTION PUMP TIMING...........66
REMOVAL..............................68
INSTALLATION...........................71
FUEL INJECTION PUMP DATA PLATE
SPECIFICATIONS........................73FUEL LEVEL SENDING UNIT / SENSOR
DESCRIPTION...........................73
OPERATION.............................73
FUEL LINES
DESCRIPTION...........................73
OPERATION.............................74
DIAGNOSIS AND TESTING.................74
HIGH-PRESSURE FUEL LINE LEAK.........74
REMOVAL..............................75
INSTALLATION...........................77
FUEL TANK
DESCRIPTION...........................78
FUEL TANK MODULE
DESCRIPTION...........................78
OPERATION.............................78
REMOVAL..............................78
INSTALLATION...........................79
FUEL TRANSFER PUMP
DESCRIPTION...........................79
OPERATION.............................79
DIAGNOSIS AND TESTING.................80
FUEL TRANSFER PUMP PRESSURE........80
REMOVAL..............................83
INSTALLATION...........................83
OVERFLOW VALVE
DESCRIPTION...........................83
OPERATION.............................83
DIAGNOSIS AND TESTING.................84
OVERFLOW VALVE.....................84
REMOVAL..............................84
INSTALLATION...........................85
WATER IN FUEL SENSOR
DESCRIPTION...........................85
OPERATION.............................85
REMOVAL..............................85
FUEL DRAIN MANIFOLD
DESCRIPTION...........................86
OPERATION.............................86
REMOVAL..............................86
INSTALLATION...........................86
FUEL DELIVERY - DIESEL
DESCRIPTION - DIESEL FUEL DELIVERY
SYSTEM
The fuel system on the Cummins 24 valveÐTurbo
Diesel Engine uses anelectronicfuel injection
pump with three control modules.Also refer to the Powertrain Control Module (PCM)
or Engine Control Module sections.
Some fuel system components are shown in (Fig.
1).
The fuel delivery system consists of the:
²Accelerator pedal
²Air cleaner housing/element
²Fuel drain manifold (passage)
14 - 54 FUEL DELIVERY - DIESELBR/BE
Page 1576 of 2889
DIAGNOSIS AND TESTING - BOOST PRESSURE
Two pressure gauges attached at two different
points are required for this test.(1) Obtain two 6828 fuel pressure test gauges
(equivalent gauges are OK).Gauge Consistency
Test:Connect the gauges together to a common pres-
sure source and verify pressure consistency of both
gauges. Do this consistency test at approximately 206
kPa (30 psi). If pressures are different, they can still
be used for test. Note and record differences in pres-
sures before testing. Make adjustments as necessary.
(2) Remove 3/4º pipe plug fitting at rear of intake
manifold (Fig. 2). Temporarily replace this fitting
with fitting reducer to adapt to pressure gauge.
Note: This pipe plug is located to front of MAP
sensor. Do not remove plug to rear of MAP sen-
sor. This is a COOLANT passage plug.
(3) Loosen hose clamp and disconnect rubber sig-
nal line (Fig. 3) from 1/8º brass fitting at front of tur-
bocharger.
(4) Remove 1/8º brass fitting (Fig. 3) from turbo-
charger. Temporarily replace this fitting with a 1/8º
ªTº fitting to adapt to pressure gauge.
(5) Reattach signal line to temporary ªTº.
(6) Attach first pressure gauge to intake manifold
fitting.
(7) Attach second pressure gauge to ªTº fitting at
turbocharger.
Engine must be at rated RPM and full load for the
test.
If gauge pressure differential is greater than 3 psi
(6 in. Hg), check intercooler and associated piping for
restrictions, plugging or damage.
Maximum pressure at intake manifold (rated rpm
and load) is 36±37 in/hg63 in/hg (17.7±18.2 psi6
1.5 psi).
Wastegate should open at no higher than 38.7
in/hg (19 psi) at wide open throttle, full load. If
wastegate is out of adjustment, a DTC may have
been set. Refer to Wastegate Adjustment in Engines
for adjustment procedures.
Fig. 2 Boost Pressure Test at Intake Manifold
1 - REAR OF INTAKE MANIFOLD
2 - 3/49PIPE PLUG
Fig. 3 Boost Pressure Test at Turbocharger
1 - TURBOCHARGER
2 - 1/89FITTING
3 - SIGNAL LINE
4 - WASTEGATE ACTUATOR
5 - CONTROL ROD
6 - OIL SUPPLY LINE
BR/BEFUEL INJECTION - DIESEL 14 - 89
FUEL INJECTION - DIESEL (Continued)
Page 1590 of 2889
REMOVAL - DIESEL
The IAT sensor is located in the left/rear side of
the intake manifold (Fig. 32).
The IAT sensor is located in the left/rear side of
the intake manifold (Fig. 32).
(1) Disconnect electrical connector from IAT sensor
(Fig. 32).
(2) Remove IAT sensor from intake manifold (Fig.
33).
(3) Discard sensor o-ring (Fig. 33).
INSTALLATION - DIESEL
The IAT sensor is located in the left/rear side of
the intake manifold (Fig. 32).
(1) Clean sensor mounting hole (Fig. 33) of rust or
contaminants.
(2) Install new o-ring to sensor. Apply clean engine
oil to sensor o-ring and sensor threads.
(3) Install IAT sensor into intake manifold.
Tighten to 14 N´m (10 ft. lbs.) torque.
(4) Connect sensor electrical connector.
MAP SENSOR
DESCRIPTION - DIESEL
The MAP sensor is installed into the rear of the
intake manifold (Fig. 31).
OPERATION - DIESEL
The MAP sensor reacts to air pressure changes in
the intake manifold. It provides an input voltage to
the Engine Control Module (ECM). As pressure
changes, MAP sensor voltage will change. The
change in MAP sensor voltage results in a different
input voltage to the ECM. The ECM uses this input,
along with inputs from other sensors to provide fuel
timing, fuel control and engine protection. Engine
protection is used to derate (drop power off) the
engine if turbocharger pressure becomes to high.
Fig. 32 IAT Sensor
1 - SENSOR MOUNTING HOLES
2 - O-RING
3 - IAT SENSOR
4 - MAP SENSOR
5 - O-RING
Fig. 33 Intake Manifold Air Temperature (IAT) Sensor
Location
1 - MANIFOLD AIR PRESSURE (MAP) SENSOR
2 - REAR OF CYLINDER HEAD
3 - IAT SENSOR
4 - ELECTRICAL CONNECTOR
5 - ELECTRICAL CONNECTOR
BR/BEFUEL INJECTION - DIESEL 14 - 103
INTAKE AIR TEMPERATURE SENSOR (Continued)
Page 2792 of 2889
(M)Malfunction Indicator Lamp (MIL) illuminated during engine operation if this DTC was recorded
(depending if required by CARB and/or EPA). MIL is displayed as an engine icon on instrument panel.
(G)Generator lamp illuminated
Generic Scan
Tool P-CodeDRB Scan Tool Display Brief Description of DTC
P0206 (M) Injector #6 Control Circuit Injector #6 output driver stage does not respond properly
to the control signal.
P0207 (M) Injector #7 Control Circuit Injector #7 output driver stage does not respond properly
to the control signal.
P0208 (M) Injector #8 Control Circuit Injector #8 output driver stage does not respond properly
to the control signal.
P0209 (M) Injector #9 Control Circuit Injector #9 output driver stage does not respond properly
to the control signal.
P0210 (M) Injector #10 Control Circuit Injector #10 output driver stage does not respond properly
to the control signal.
P0215 Fuel Injection Pump Control Circuit Failure in fuel pump relay control circuit.
P0216 (M) Fuel Injection Pump Timing Failure High fuel supply restriction, low fuel pressure or possible
wrong or incorrectly installed pump keyway.
P0217 Decreased Engine Performance Due
To Engine Overheat ConditionEngine overheating. ECM will derate engine performance.
P0219 Crankshaft Position Sensor
Overspeed SignalEngine has exceeded rpm limits.
P0222 (M) Idle Validation Signals Both Low Problem detected with idle validation circuits within APPS.
P0223 (M) Idle Validation Signals Both High
(Above 5 Volts)Problem detected with idle validation circuits within APPS.
P0230 Transfer Pump (Lift Pump) Circuit
Out of RangeProblem detected in fuel transfer pump circuits.
P0232 Fuel Shutoff Signal Voltage Too High Fuel shut-off signal voltage too high from ECM to fuel
injection pump.
P0234 (M) Turbo Boost Limit Exceeded Problem detected in turbocharger wastegate.
P0236 (M) Map Sensor Too High Too Long Problem detected in turbocharger wastegate.
P0237 (M) Map Sensor Voltage Too Low MAP sensor voltage input below the minimum acceptable
voltage.
P0238 (M) Map Sensor Voltage Too High MAP sensor voltage input above the maximum
acceptable voltage.
P0251 (M) Fuel Inj. Pump Mech. Failure Fuel
Valve Feedback CircuitProblem sensed with fuel circuit internal to fuel injection
pump.
P0253 (M) Fuel Injection Pump Fuel Valve
Open CircuitProblem sensed with fuel circuit internal to fuel injection
pump.
P0254 Fuel Injection Pump Fuel Valve
Current Too HighProblem caused by internal fuel injection pump failure.
P0300 (M) Multiple Cylinder Mis-fire Misfire detected in multiple cylinders.
P0301 (M) CYLINDER #1 MISFIRE Misfire detected in cylinder #1.
P0302 (M) CYLINDER #2 MISFIRE Misfire detected in cylinder #2.
P0303 (M) CYLINDER #3 MISFIRE Misfire detected in cylinder #3.
P0304 (M) CYLINDER #4 MISFIRE Misfire detected in cylinder #4.
P0305 (M) CYLINDER #5 MISFIRE Misfire detected in cylinder #5.
BR/BEEMISSIONS CONTROL 25 - 5
EMISSIONS CONTROL (Continued)
Page 2810 of 2889
FUEL PRESSURE
The fuel pressure regulator controls fuel system
pressure. The PCM cannot detect a clogged fuel
pump inlet filter, clogged in-line fuel filter, or a
pinched fuel supply or return line. However, these
could result in a rich or lean condition causing the
PCM to store an oxygen sensor or fuel system diag-
nostic trouble code.
SECONDARY IGNITION CIRCUIT
The PCM cannot detect an inoperative ignition coil,
fouled or worn spark plugs, ignition cross firing, or
open spark plug cables.
CYLINDER COMPRESSION
The PCM cannot detect uneven, low, or high engine
cylinder compression.
EXHAUST SYSTEM
The PCM cannot detect a plugged, restricted or
leaking exhaust system, although it may set a fuel
system fault.
FUEL INJECTOR MECHANICAL MALFUNCTIONS
The PCM cannot determine if a fuel injector is
clogged, the needle is sticking or if the wrong injector
is installed. However, these could result in a rich or
lean condition causing the PCM to store a diagnostic
trouble code for either misfire, an oxygen sensor, or
the fuel system.
EXCESSIVE OIL CONSUMPTION
Although the PCM monitors engine exhaust oxygen
content when the system is in closed loop, it cannot
determine excessive oil consumption.
THROTTLE BODY AIR FLOW
The PCM cannot detect a clogged or restricted air
cleaner inlet or filter element.
VACUUM ASSIST
The PCM cannot detect leaks or restrictions in the
vacuum circuits of vacuum assisted engine control
system devices. However, these could cause the PCM
to store a MAP sensor diagnostic trouble code and
cause a high idle condition.
PCM SYSTEM GROUND
The PCM cannot determine a poor system ground.
However, one or more diagnostic trouble codes may
be generated as a result of this condition. The mod-
ule should be mounted to the body at all times, also
during diagnostic.
PCM CONNECTOR ENGAGEMENT
The PCM may not be able to determine spread or
damaged connector pins. However, it might storediagnostic trouble codes as a result of spread connec-
tor pins.
OPERATION - NON-MONITORED CIRCUITS -
DIESEL
The PCM and/or the ECM will not monitor certain
malfunctioning circuits or components that could
cause driveability problems. Also, a Diagnostic Trou-
ble Code (DTC) might not be stored for these mal-
functions. However, problems with these circuits or
components may cause the PCM/ECM to store DTC's
for other circuits or components.EXAMPLES:A cyl-
inder with low compression will not set a DTC
directly, but may cause an engine misfire. This in
turn may cause the ECM to set a DTC for an engine
misfire. Or, a dirty or plugged air filter will not set a
DTC directly, but may cause lack of turbocharger
boost. This in turn may cause the ECM to set a DTC
for a boost pressure malfunction.
FUEL PRESSURE
Primary fuel pressure from the fuel tank to the
fuel injection pump is supplied by the low-pressure
fuel transfer pump. High-pressure to the fuel injec-
tors is supplied by the fuel injection pump. The ECM
cannot detect actual fuel pressure, a clogged fuel fil-
ter, clogged fuel screen, or a pinched fuel supply or
return line. However, a DTC may be set due to an
engine misfire.
CYLINDER COMPRESSION
The ECM cannot detect uneven, low, or high
engine cylinder compression. However, these could
result in a possible misfire which may set a DTC.
EXHAUST SYSTEM
The ECM cannot detect a plugged, restricted or
leaking exhaust system. However, DTC's may be set
for engine misfire, high intake manifold temperature,
high engine coolant temperature, turbocharger over-
boost or turbocharger underboost.
FUEL INJECTOR MECHANICAL MALFUNCTIONS
The ECM cannot determine if a fuel injector is
clogged, the needle is sticking or if the wrong injector
is installed. However, these could result in a possible
misfire which may set a DTC.
EXCESSIVE OIL CONSUMPTION
The ECM cannot determine excessive oil consump-
tion. However, if excess oil consumption is high
enough, it could result in a possible engine misfire
which may set a DTC.
BR/BEEMISSIONS CONTROL 25 - 23
EMISSIONS CONTROL (Continued)
Page 2857 of 2889
COVER(S) - INSPECTION, CYLINDER
HEAD............9-138,9-194,9-24,9-253,9-81
COVER(S) - INSTALLATION, CYLINDER
HEAD............9-138,9-194,9-24,9-253,9-81
COVER(S) - INSTALLATION, TIMING
BELT / CHAIN.........9-113,9-169,9-226,9-56
COVERS - INSTALLATION, WHEEL.......30-10
COVER(S) - REMOVAL, CYLINDER HEAD . 9-138,
9-194,9-24,9-253,9-81
COVER(S) - REMOVAL, TIMING BELT /
CHAIN...............9-113,9-169,9-225,9-56
COWL GRILLE - INSTALLATION.........23-90
COWL GRILLE - REMOVAL.............23-90
COWL TRIM COVER - INSTALLATION....23-120
COWL TRIM COVER - REMOVAL.......23-119
COWL WEATHERSTRIP - INSTALLATION . 23-153
COWL WEATHERSTRIP - REMOVAL.....23-153
C-PILLAR TRIM - INSTALLATION.......23-128
C-PILLAR TRIM - REMOVAL...........23-128
CRANKCASE BREATHER VAPOR
CANISTER - INSTALLATION.............9-242
CRANKCASE BREATHER VAPOR
CANISTER - REMOVAL................9-241
CRANKCASE VENT HOSE - OPERATION . . . 25-32
CRANKSHAFT - DESCRIPTION . 9-145,9-275,9-31,
9-88
CRANKSHAFT - INSTALLATION....9-145,9-203,
9-32,9-89
CRANKSHAFT - OPERATION....9-145,9-31,9-88
CRANKSHAFT - REMOVAL . . 9-145,9-202,9-31,9-88
CRANKSHAFT JOURNAL CLEARANCE -
STANDARD PROCEDURE, CONNECTING
ROD BEARING.......................9-274
CRANKSHAFT MAIN BEARING FITTING -
STANDARD PROCEDURE...........9-146,9-90
CRANKSHAFT MAIN BEARINGS -
DESCRIPTION...............9-146,9-32,9-90
CRANKSHAFT MAIN BEARINGS -
INSTALLATION.........9-147,9-204,9-34,9-90
CRANKSHAFT MAIN BEARINGS -
OPERATION.................9-146,9-32,9-90
CRANKSHAFT MAIN BEARINGS -
REMOVAL.............9-147,9-204,9-33,9-90
CRANKSHAFT OIL SEAL - FRONT -
DESCRIPTION...............9-147,9-34,9-91
CRANKSHAFT OIL SEAL - FRONT -
INSTALLATION.........9-148,9-277,9-34,9-91
CRANKSHAFT OIL SEAL - FRONT -
OPERATION.................9-147,9-34,9-91
CRANKSHAFT OIL SEAL - FRONT -
REMOVAL.............9-147,9-276,9-34,9-91
CRANKSHAFT OIL SEAL - REAR -
DESCRIPTION...............9-148,9-34,9-91
CRANKSHAFT OIL SEAL - REAR -
INSTALLATION....9-149,9-206,9-278,9-35,9-92
CRANKSHAFT OIL SEAL - REAR -
OPERATION.................9-148,9-34,9-92
CRANKSHAFT OIL SEAL - REAR -
REMOVAL........9-149,9-206,9-278,9-35,9-92
CRANKSHAFT REAR OIL SEAL RETAINER
- INSTALLATION................9-206,9-279
CRANKSHAFT REAR OIL SEAL RETAINER
- REMOVAL....................9-206,9-278
CROSSHEADS - CLEANING.............9-249
CROSSHEADS - INSPECTION...........9-250
CRUISE INDICATOR - DESCRIPTION......8J-18
CRUISE INDICATOR - OPERATION.......8J-18
CUBBY BIN - INSTALLATION...........23-110
CUBBY BIN - REMOVAL..............23-110
CUMMINS TURBO DIESEL -
DESCRIPTION, MAINTENANCE
SCHEDULES - 24-VALVE................0-22
CUP HOLDER - INSTALLATION.........23-111
CUP HOLDER - REMOVAL.............23-110
CUSHION - INSTALLATION, SEAT.......23-138
CUSHION - REMOVAL, SEAT...........23-138
CUSHION COVER - INSTALLATION, SEAT . 23-139
CUSHION COVER - REMOVAL, SEAT.....23-139
CUSHION COVER - SPLIT BENCH -
INSTALLATION, SEAT.................23-140
CUSHION COVER - SPLIT BENCH -
REMOVAL, SEAT....................23-139
CYLINDER - DESCRIPTION, MASTER
......5-29
CYLINDER - DIAGNOSIS AND TESTING,
IGNITION SWITCH AND KEY LOCK
.......19-10
CYLINDER - INSTALLATION, LOCK
.......23-73
CYLINDER - INSTALLATION, MASTER
.....5-30
CYLINDER - OPERATION, MASTER
........5-29CYLINDER - REMOVAL, LOCK...........23-73
CYLINDER - REMOVAL, MASTER.........5-30
CYLINDER BLEEDING - STANDARD
PROCEDURE, MASTER.................5-30
CYLINDER BORE HONING - STANDARD
PROCEDURE...........9-10,9-126,9-180,9-69
CYLINDER BORE REPAIR - STANDARD
PROCEDURE........................9-265
CYLINDER COMBUSTION PRESSURE
LEAKAGE - DIAGNOSIS AND TESTING....9-124,
9-179,9-67,9-9
CYLINDER COMPRESSION PRESSURE -
DIAGNOSIS AND TESTING . 9-124,9-179,9-67,9-9
CYLINDER COVER GASKET -
DESCRIPTION........................9-79
CYLINDER HEAD - CLEANING . 9-137,9-193,9-23,
9-248,9-80
CYLINDER HEAD - DESCRIPTION . . 9-136,9-191,
9-22,9-246,9-79
CYLINDER HEAD - INSPECTION....9-137,9-193,
9-23,9-250,9-80
CYLINDER HEAD - INSTALLATION . . 9-137,9-193,
9-23,9-250,9-80
CYLINDER HEAD - OPERATION . . 9-136,9-22,9-79
CYLINDER HEAD - REMOVAL . 9-137,9-192,9-23,
9-246,9-80
CYLINDER HEAD COVER GASKET -
DESCRIPTION........................9-22
CYLINDER HEAD COVER GASKET -
OPERATION..........................9-22
CYLINDER HEAD COVER(S) - CLEANING . . 9-138,
9-194,9-24,9-253,9-81
CYLINDER HEAD COVER(S) -
DESCRIPTION.......................9-194
CYLINDER HEAD COVER(S) -
INSPECTION......9-138,9-194,9-24,9-253,9-81
CYLINDER HEAD COVER(S) -
INSTALLATION....9-138,9-194,9-24,9-253,9-81
CYLINDER HEAD COVER(S) - REMOVAL . . 9-138,
9-194,9-24,9-253,9-81
CYLINDER HEAD GASKET FAILURE -
DIAGNOSIS AND TESTING....9-136,9-191,9-22,
9-79
CYLINDER HOUSING - INSTALLATION,
LOCK..............................19-11
CYLINDER HOUSING - REMOVAL, LOCK . . 19-10
CYLINDER LOCK SWITCH -
DESCRIPTION, DOOR..................8N-5
CYLINDER LOCK SWITCH - DIAGNOSIS
& TESTING, DOOR....................8N-5
CYLINDER LOCK SWITCH -
INSTALLATION, DOOR.................8N-6
CYLINDER LOCK SWITCH - OPERATION,
DOOR..............................8N-5
CYLINDER LOCK SWITCH - REMOVAL,
DOOR..............................8N-6
CYLINDER/POWER BOOSTER -
DIAGNOSIS AND TESTING, MASTER......5-29
CYLINDERS - ASSEMBLY, WHEEL.........5-31
CYLINDERS - CLEANING, WHEEL.........5-31
CYLINDERS - DESCRIPTION, LOCK.......23-1
CYLINDERS - DISASSEMBLY, WHEEL......5-31
CYLINDERS - INSPECTION, WHEEL.......5-31
CYLINDERS - INSTALLATION, WHEEL.....5-32
CYLINDERS - REMOVAL, WHEEL.........5-31
DAM - INSTALLATION, FRONT AIR........13-2
DAM - REMOVAL, FRONT AIR...........13-1
DAMAGED OR WORN THREADS -
STANDARD PROCEDURE,
REPAIR ..........9-11,9-125,9-181,9-238,9-68
DAMPER - INSPECTION, VIBRATION.....9-289
DAMPER - INSTALLATION,
VIBRATION.......9-156,9-212,9-289,9-42,9-99
DAMPER - REMOVAL,
VIBRATION.......9-155,9-212,9-289,9-42,9-99
DATA BUS - DESCRIPTION, CCD..........8E-6
DATA BUS - DIAGNOSIS AND TESTING,
CCD ...............................8E-11
DATA BUS - OPERATION, CCD...........8E-7
DATA LINK CONNECTOR - DESCRIPTION . . 8E-12
DATA LINK CONNECTOR - OPERATION
....8E-12
DATA PLATE - DESCRIPTION, ENGINE
....9-244
DATA PLATE, SPECIFICATIONS - FUEL
INJECTION PUMP
....................14-73
DAY / NIGHT MIRROR - DESCRIPTION,
AUTOMATIC
........................8N-10
DAY / NIGHT MIRROR - INSTALLATION,
AUTOMATIC
........................8N-12DAY / NIGHT MIRROR - OPERATION,
AUTOMATIC........................8N-11
DAY / NIGHT MIRROR - REMOVAL,
AUTOMATIC........................8N-12
DAY/NIGHT MIRROR - DIAGNOSIS AND
TESTING, AUTOMATIC................8N-11
DAYTIME RUNNING LAMP MODULE -
DESCRIPTION........................8L-9
DAYTIME RUNNING LAMP MODULE -
INSTALLATION........................8L-9
DAYTIME RUNNING LAMP MODULE -
OPERATION..........................8L-9
DAYTIME RUNNING LAMP MODULE -
REMOVAL...........................8L-9
DECALS - INSTALLATION..............23-63
DECALS - INSTALLATION, BODY
STRIPES...........................23-87
DECALS - REMOVAL..................23-63
DECALS - REMOVAL, BODY STRIPES.....23-87
DEFINITION - DESCRIPTION, TRIP.......25-18
DEFROSTER AND DEMISTER DUCT
ADAPTER - INSTALLATION.............24-35
DEFROSTER AND DEMISTER DUCT
ADAPTER - REMOVAL.................24-35
DEFROSTER AND DEMISTER DUCTS -
INSTALLATION.......................24-35
DEFROSTER AND DEMISTER DUCTS -
REMOVAL..........................24-34
DE-GLAZE - STANDARD PROCEDURE-
CYLINDER BORE.....................9-264
DELIVERY - DIESEL - OPERATION, FUEL . . 14-56
DELIVERY - SPECIFICATIONS, TORQUE -
FUEL...............................14-4
DELIVERY STORAGE - DESCRIPTION,
PRE ...............................30-19
DELIVERY STORAGE - STANDARD
PROCEDURE, PRE....................30-20
DELIVERY SYSTEM - DESCRIPTION,
DIESEL FUEL........................14-54
DELIVERY SYSTEM - DESCRIPTION,
FUEL...............................14-2
DELIVERY SYSTEM - OPERATION, FUEL . . . 14-2
DEMAGNETIZING - STANDARD
PROCEDURE, COMPASS...............8M-5
DEMISTER DUCT ADAPTER -
INSTALLATION, DEFROSTER............24-35
DEMISTER DUCT ADAPTER - REMOVAL,
DEFROSTER.........................24-35
DEMISTER DUCTS - INSTALLATION,
DEFROSTER.........................24-35
DEMISTER DUCTS - REMOVAL,
DEFROSTER.........................24-34
DEMISTER DUCTS - REMOVAL,
INSTRUMENT PANEL..................24-37
DEMISTER GRILLES - INSTALLATION.....24-32
DEMISTER GRILLES - REMOVAL........24-31
DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER AN
AIRBAG.............................8O-4
DETECTION PUMP - DESCRIPTION, LEAK . 25-33
DETECTION PUMP - INSTALLATION,
LEAK..............................25-34
DETECTION PUMP - REMOVAL, LEAK....25-34
DIAGNOSIS - INTRODUCTION -
DIAGNOSIS AND TESTING, ENGINE . 9-118,9-173,
9-3
DIAGNOSIS - MECHANICAL - DIAGNOSIS
AND TESTING, ENGINE................9-232
DIAGNOSIS CHARTS - DIAGNOSIS AND
TESTING........21-149,21-320,21-492,21-663
DIAGNOSIS CHARTS - DIAGNOSIS AND
TESTING, SMOKE....................9-234
DIAGNOSIS, INTRODUCTION -
DIAGNOSIS AND TESTING-ENGINE........9-61
DIAGNOSTIC AND TESTING, CLUTCH.......6-2
DIAGNOSTIC TROUBLE CODES -
DESCRIPTION........................25-2
DIAGNOSTICS (OBD) - DIAGNOSIS AND
TESTING, ON-BOARD...................7-4
DIAGRAMS - DESCRIPTION, HOW TO
USE WIRING
......................8W-01-1
DIAGRAMS - HYDRAULIC SCHEMATICS,
SCHEMATICS
.....21-174,21-345,21-520,21-690
DIESEL - CLEANING, RADIATOR - 5.9L
....7-65
DIESEL - CLEANING, RADIATOR FAN -
5.9L
................................7-44
DIESEL - CLEANING, WATER PUMP -
5.9L
................................7-73
10 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page
Page 2858 of 2889
DIESEL - DESCRIPTION................25-1
DIESEL - DESCRIPTION........14-102,14-103
DIESEL - DESCRIPTION.................8I-5
DIESEL - DESCRIPTION, 5.9L............11-3
DIESEL - DESCRIPTION, BELT
TENSIONERS - 5.9L...................7-23
DIESEL - DESCRIPTION, COOLANT
RECOVERY CONTAINER - 3.9L/5.2L/
5.9L/5.9L............................7-41
DIESEL - DESCRIPTION, COOLING
SYSTEM FLOW - 5.9L...................7-1
DIESEL - DESCRIPTION, ENGINE 5.9L....9-231
DIESEL - DESCRIPTION, ENGINE BLOCK
HEATER - 5.9L........................7-47
DIESEL - DESCRIPTION, ENGINE
COOLANT THERMOSTAT - 5.9L...........7-54
DIESEL - DESCRIPTION, FAN DRIVE
VISCOUS CLUTCH - 5.9L...............7-57
DIESEL - DESCRIPTION, MAINTENANCE
SCHEDULES - 24-VALVE CUMMINS
TURBO..............................0-22
DIESEL - DESCRIPTION, RADIATOR -
5.9L................................7-63
DIESEL - DESCRIPTION, TRANS COOLER
- 5.9L..............................7-85
DIESEL - DESCRIPTION, VACUUM PUMP
- 5.9L..............................7-34
DIESEL - DESCRIPTION, WATER PUMP -
5.9L................................7-73
DIESEL - FUEL INJECTOR FIRING ORDER . 14-58
DIESEL - INSPECTION, EXHAUST PIPE -
5.9L................................11-9
DIESEL - INSPECTION, RADIATOR - 5.9L . . . 7-65
DIESEL - INSPECTION, RADIATOR FAN -
5.9L................................7-44
DIESEL - INSPECTION, TAILPIPE - 5.9L . . . 11-12
DIESEL - INSPECTION, WATER PUMP -
5.9L................................7-73
DIESEL - INSTALLATION..............14-103
DIESEL - INSTALLATION................8I-8
DIESEL - INSTALLATION, BELT
TENSIONERS - 5.9L...................7-23
DIESEL - INSTALLATION, COOLANT
RECOVERY CONTAINER - 3.9L/5.2L/
5.9L/5.9L............................7-41
DIESEL - INSTALLATION, DRIVE BELTS -
5.9L................................7-34
DIESEL - INSTALLATION, ENGINE BLOCK
HEATER - 5.9L........................7-47
DIESEL - INSTALLATION, ENGINE
COOLANT THERMOSTAT - 5.9L...........7-55
DIESEL - INSTALLATION, EXHAUST PIPE
- 5.9L..............................11-10
DIESEL - INSTALLATION, MUFFLER -
5.9L...............................11-11
DIESEL - INSTALLATION, RADIATOR -
5.9L................................7-65
DIESEL - INSTALLATION, RADIATOR FAN
- 5.9L..............................7-45
DIESEL - INSTALLATION, TAILPIPE - 5.9L . 11-12
DIESEL - INSTALLATION, TRANS
COOLER - 5.9L.......................7-88
DIESEL - INSTALLATION, VACUUM
PUMP - 5.9L.........................7-37
DIESEL - INSTALLATION, WATER PUMP -
5.9L................................7-74
DIESEL - OPERATION
.................8E-18
DIESEL - OPERATION
.................25-19
DIESEL - OPERATION
..........14-102,14-103
DIESEL - OPERATION
...................8I-5
DIESEL - OPERATION, BELT
TENSIONERS - 5.9L
...................7-23
DIESEL - OPERATION, COOLANT
RECOVERY CONTAINER - 3.9L/5.2L/
5.9L/5.9L
............................7-41
DIESEL - OPERATION, ENGINE BLOCK
HEATER - 5.9L
........................7-47
DIESEL - OPERATION, ENGINE COOLANT
THERMOSTAT - 5.9L
...................7-54
DIESEL - OPERATION, FAN DRIVE
VISCOUS CLUTCH - 5.9L
...............7-57
DIESEL - OPERATION, FUEL DELIVERY
. . . 14-56
DIESEL - OPERATION, NON-MONITORED
CIRCUITS
...........................25-23
DIESEL - OPERATION, RADIATOR - 5.9L
. . . 7-63
DIESEL - OPERATION, TRANS COOLER -
5.9L
................................7-85DIESEL - OPERATION, VACUUM PUMP -
5.9L................................7-35
DIESEL - OPERATION, WATER PUMP -
5.9L................................7-73
DIESEL - REMOVAL............14-103,14-104
DIESEL - REMOVAL....................8I-7
DIESEL - REMOVAL, BELT TENSIONERS -
5.9L................................7-23
DIESEL - REMOVAL, COOLANT
RECOVERY CONTAINER - 3.9L/5.2L/
5.9L/5.9L............................7-41
DIESEL - REMOVAL, DRIVE BELTS - 5.9L . . 7-33
DIESEL - REMOVAL, ENGINE BLOCK
HEATER - 5.9L........................7-47
DIESEL - REMOVAL, ENGINE COOLANT
THERMOSTAT - 5.9L...................7-55
DIESEL - REMOVAL, EXHAUST PIPE -
5.9L................................11-9
DIESEL - REMOVAL, MUFFLER - 5.9L.....11-11
DIESEL - REMOVAL, RADIATOR - 5.9L.....7-63
DIESEL - REMOVAL, RADIATOR FAN -
5.9L................................7-44
DIESEL - REMOVAL, TAILPIPE - 5.9L.....11-12
DIESEL - REMOVAL, VACUUM PUMP -
5.9L................................7-35
DIESEL - REMOVAL, WATER PUMP -
5.9L................................7-73
DIESEL ENGINE - DESCRIPTION, FUEL
REQUIREMENTS.......................0-2
DIESEL ENGINE - DIAGNOSIS AND
TESTING............................11-4
DIESEL ENGINE - DIAGNOSIS AND
TESTING, COOLING SYSTEM............7-12
DIESEL ENGINE - INSTALLATION........19-35
DIESEL ENGINE - REMOVAL............19-33
DIESEL ENGINE - STANDARD
PROCEDURE, DRAINING COOLING
SYSTEM 5.9L........................7-15
DIESEL ENGINE - STANDARD
PROCEDURE, REFILLING COOLING
SYSTEM 5.9L........................7-15
DIESEL ENGINE - TORQUE.............14-90
DIESEL ENGINE, SPECIAL TOOLS - 5.9L . . 9-244
DIESEL ENGINES - DESCRIPTION,
COMPONENT MONITORS..............25-18
DIESEL ENGINES - FUEL SYSTEM
PRESSURES........................14-58
DIESEL FUEL DELIVERY SYSTEM -
DESCRIPTION.......................14-54
DIESEL FUEL INJECTION SYSTEM -
DESCRIPTION.......................14-87
DIESEL FUEL SYSTEM, SPECIAL TOOLS . . 14-59
DIESEL FUEL TANK - DESCRIPTION......14-78
DIESEL, SPECIFICATIONS - 5.9L.........9-242
DIESEL WITH AUTO. TRANS. -
INSTALLATION..................8P-11,8P-4
DIESEL WITH AUTO. TRANS. - REMOVAL . . 8P-4,
8P-8
DIFFERENTIAL - ASSEMBLY . . 3-128,3-159,3-188,
3-37,3-69,3-98
DIFFERENTIAL - DISASSEMBLY....3-128,3-158,
3-188,3-36,3-68,3-97
DIFFERENTIAL - INSTALLATION....3-129,3-159,
3-188,3-37,3-69,3-98
DIFFERENTIAL - POWR-LOK - ASSEMBLY . 3-163
DIFFERENTIAL - POWR-LOK -
DISASSEMBLY.......................3-161
DIFFERENTIAL - REMOVAL . . 3-127,3-158,3-187,
3-36,3-68,3-96
DIFFERENTIAL - TRAC-LOK - ASSEMBLY . . 3-101,
3-132,3-190
DIFFERENTIAL - TRAC-LOK -
DISASSEMBLY..............3-130,3-190,3-99
DIFFERENTIAL CASE BEARINGS -
INSTALLATION . . . 3-103,3-134,3-164,3-192,3-39,
3-71
DIFFERENTIAL CASE BEARINGS -
REMOVAL . . . 3-103,3-134,3-164,3-192,3-39,3-71
DIMENSION, SPECIFICATIONS - FRAME....13-7
DIMENSIONS, SPECIFICATIONS - BODY
OPENING...........................23-60
DIODE - INSTALLATION............8W-01-10
DIODE - REMOVAL
................8W-01-10
DIODE REPLACEMENT - STANDARD
PROCEDURE
.........................24-7
DISC - DESCRIPTION, CLUTCH
............6-7
DISC - INSTALLATION, CLUTCH
...........6-9
DISC - OPERATION, CLUTCH
.............6-8DISC - REMOVAL, CLUTCH...............6-8
DISC BRAKE CALIPERS - ASSEMBLY......5-12
DISC BRAKE CALIPERS - CLEANING......5-12
DISC BRAKE CALIPERS - DISASSEMBLY . . . 5-11
DISC BRAKE CALIPERS - INSPECTION.....5-12
DISC BRAKE ROTOR - DIAGNOSIS AND
TESTING............................5-20
DISC BRAKES - DESCRIPTION,
2500/3500 WITH REAR.................5-35
DISC BRAKES - INSTALLATION, REAR
PARK BRAKE CABLE - 2500/3500
WITH REAR..........................5-38
DISC BRAKES - OPERATION, 2500/3500
WITH REAR..........................5-36
DISC BRAKES - REMOVAL, REAR PARK
BRAKE CABLE - 2500/3500 WITH
REAR...............................5-37
DISCHARGE LINE - INSTALLATION,
SUCTION...........................24-51
DISCHARGE LINE - REMOVAL, SUCTION . . 24-50
DISPLAY TEST MODE - DESCRIPTION,
STATE ..............................25-1
DISTRIBUTION - DESCRIPTION, POWER . 8W-97-1
DISTRIBUTION - OPERATION, POWER . . 8W-97-1
DISTRIBUTION CENTER - DESCRIPTION,
POWER..........................8W-97-7
DISTRIBUTION CENTER - INSTALLATION,
POWER..........................8W-97-8
DISTRIBUTION CENTER - OPERATION,
POWER..........................8W-97-8
DISTRIBUTION CENTER - REMOVAL,
POWER...........................8W-97-8
DISTRIBUTION SYSTEMS, SPECIAL
TOOLS - POWER...................8W-97-2
DISTRIBUTOR - DESCRIPTION..........8I-10
DISTRIBUTOR - INSTALLATION..........8I-11
DISTRIBUTOR - OPERATION............8I-11
DISTRIBUTOR - REMOVAL..............8I-11
DISTRIBUTOR BUSHING - INSTALLATION . 9-150,
9-37,9-94
DISTRIBUTOR BUSHING - REMOVAL.....9-150,
9-37,9-94
DISTRIBUTOR CAP - DIAGNOSIS AND
TESTING............................8I-12
DISTRIBUTOR ROTOR - DIAGNOSIS AND
TESTING............................8I-13
DOME LAMP - INSTALLATION..........8L-33
DOME LAMP - REMOVAL..............8L-33
DOOR - ADJUSTMENT, CARGO..........23-78
DOOR - INSTALLATION...........23-68,23-78
DOOR - INSTALLATION, BLEND.........24-38
DOOR - INSTALLATION, FUEL FILL.......23-95
DOOR - INSTALLATION, HEAT/DEFROST . . . 24-39
DOOR - INSTALLATION, PANEL/DEFROST . . 24-39
DOOR - INSTALLATION, RECIRCULATION . . 24-39
DOOR - REMOVAL...............23-68,23-78
DOOR - REMOVAL, BLEND.............24-38
DOOR - REMOVAL, FUEL FILL..........23-95
DOOR - REMOVAL, HEAT/DEFROST......24-38
DOOR - REMOVAL, PANEL/DEFROST.....24-38
DOOR - REMOVAL, RECIRCULATION.....24-39
DOOR ACTUATOR - INSTALLATION,
BLEND.............................24-26
DOOR ACTUATOR - INSTALLATION,
HEAT/DEFROST......................24-27
DOOR ACTUATOR - INSTALLATION,
PANEL/DEFROST
.....................24-27
DOOR ACTUATOR - INSTALLATION,
RECIRCULATION
.....................24-28
DOOR ACTUATOR - REMOVAL, BLEND
....24-25
DOOR ACTUATOR - REMOVAL,
HEAT/DEFROST
......................24-26
DOOR ACTUATOR - REMOVAL,
PANEL/DEFROST
.....................24-27
DOOR ACTUATOR - REMOVAL,
RECIRCULATION
.....................24-27
DOOR AJAR SWITCH - DESCRIPTION
....8L-34
DOOR AJAR SWITCH - DIAGNOSIS AND
TESTING
...........................8L-34
DOOR AJAR SWITCH - INSTALLATION
....8L-35
DOOR AJAR SWITCH - REMOVAL
........8L-35
DOOR CYLINDER LOCK SWITCH -
DESCRIPTION
........................8N-5
DOOR CYLINDER LOCK SWITCH -
DIAGNOSIS & TESTING
................8N-5
DOOR CYLINDER LOCK SWITCH -
INSTALLATION
.......................8N-6
BR/BEINDEX 11
Description Group-Page Description Group-Page Description Group-Page
Page 2866 of 2889
INJECTION PUMP TIMING - DIAGNOSIS
AND TESTING, FUEL..................14-66
INJECTION SYSTEM - DESCRIPTION, AIR . 25-25
INJECTION SYSTEM - DESCRIPTION,
DIESEL FUEL........................14-87
INJECTION SYSTEM - OPERATION, AIR . . . 25-27
INJECTION SYSTEM - TORQUE, AIR......25-28
INJECTOR - DESCRIPTION, FUEL . . . 14-53,14-93
INJECTOR - INSTALLATION, FUEL . . 14-53,14-98
INJECTOR - OPERATION, FUEL.....14-53,14-94
INJECTOR - REMOVAL, FUEL......14-53,14-96
INJECTOR FIRING ORDER, DIESEL -
FUEL..............................14-58
INJECTOR TEST - DIAGNOSIS AND
TESTING, FUEL.................14-53,14-95
INLET BAFFLE - INSTALLATION, HVAC
HOUSING...........................24-37
INLET BAFFLE - REMOVAL, HVAC
HOUSING...........................24-36
INLET FILTER - INSTALLATION..........14-22
INLET FILTER - REMOVAL..............14-22
INNER BELT WEATHERSTRIP -
INSTALLATION, FRONT DOOR..........23-154
INNER BELT WEATHERSTRIP -
REMOVAL, FRONT DOOR.............23-154
IN/OUT - ADJUSTMENT, FRONT DOOR....23-69
INPUT - DESCRIPTION, VEHICLE SPEED . . . 8P-1
INPUT - OPERATION, ASD SENSE - PCM . . . 8I-3
INSIDE HANDLE ACTUATOR -
INSTALLATION...................23-71,23-80
INSIDE HANDLE ACTUATOR - REMOVAL . . 23-71,
23-80
INSPECTION - DESCRIPTION, ROAD
TEST..............................30-15
INSPECTION - DIAGNOSIS AND
TESTING, WHEEL....................22-10
INSPECTION - INFORMATION LABELS -
STANDARD PROCEDURE...............30-22
INSPECTION, 3.9L/5.2L/5.9L ENGINES -
VISUAL............................14-28
INSPECTION, 8.0L ENGINE - VISUAL.....14-32
INSPECTION, A/C COMPRESSOR
CLUTCH............................24-16
INSPECTION, ACCUMULATOR . . . 21-192,21-363,
21-538,21-708
INSPECTION, AUTOMATIC
TRANSMISSION - 42RE...............21-165
INSPECTION, AUTOMATIC
TRANSMISSION - 44RE...............21-337
INSPECTION, AUTOMATIC
TRANSMISSION - 46RE...............21-510
INSPECTION, AUTOMATIC
TRANSMISSION - 47RE...............21-681
INSPECTION, BATTERY.................30-7
INSPECTION, BATTERY SYSTEM..........8F-5
INSPECTION, BODY SEALING...........30-10
INSPECTION, CAMSHAFT & BEARINGS
(IN BLOCK).........................9-272
INSPECTION, CATALYTIC CONVERTER -
3.9L/5.2L/5.9L........................11-5
INSPECTION, CATALYTIC CONVERTER -
5.9L HEAVY DUTY/8.0L.................11-7
INSPECTION, CHARGE AIR COOLER AND
PLUMBING.........................11-18
INSPECTION, COMPASS...............30-12
INSPECTION, CROSSHEADS............9-250
INSPECTION, CYLINDER HEAD....9-137,9-193,
9-23,9-250,9-80
INSPECTION, CYLINDER HEAD COVER(S) . 9-138,
9-194,9-24,9-253,9-81
INSPECTION, DISC BRAKE CALIPERS......5-12
INSPECTION, DOORS AND DOOR LOCKS . . 30-11
INSPECTION, DRUM...................5-33
INSPECTION, ENGINE BLOCK . 9-142,9-200,9-267,
9-28,9-86
INSPECTION, ENGINE PERFORMANCE....30-16
INSPECTION, EXHAUST MANIFOLD . 9-112,9-168,
9-225,9-304,9-55
INSPECTION, EXHAUST PIPE -
3.9L/5.2L/5.9L........................11-7
INSPECTION, EXHAUST PIPE - 5.9L
DIESEL
.............................11-9
INSPECTION, EXHAUST PIPE - 5.9L
HEAVY DUTY/8.0L
.....................11-9
INSPECTION, FIT AND FINISH
......30-10,30-12
INSPECTION, FLUID LEVELS
.............30-4
INSPECTION, FRONT CLUTCH
. . . 21-205,21-376,
21-550,21-721INSPECTION, FRONT SERVO....21-207,21-378,
21-553,21-723
INSPECTION, FUEL...................30-15
INSPECTION, GAUGES/WARNING LIGHTS . 30-19
INSPECTION, HEATER/AIR CONDITIONER . . 30-17
INSPECTION, HOOD LATCH/SAFETY
CATCH ..............................30-4
INSPECTION, HORN..................30-19
INSPECTION, INTAKE MANIFOLD . . . 9-110,9-166,
9-223,9-302,9-53
INSPECTION, INTAKE/EXHAUST VALVES
& SEATS ..............9-141,9-198,9-27,9-84
INSPECTION, KEYLESS ENTRY..........30-11
INSPECTION, LIGHTS AND SWITCHES....30-12
INSPECTION, LINES/HOSES.............30-6
INSPECTION, MANUAL - NV3500........21-15
INSPECTION, MEASURING TIMING
CHAIN STRETCH.......9-114,9-170,9-227,9-58
INSPECTION, MIRROR................30-19
INSPECTION, NEUTRAL SAFETY SWITCH . . 30-19
INSPECTION, OIL COOLER & LINES -
CLEANING..........................9-296
INSPECTION, OIL PAN . 9-106,9-162,9-219,9-297,
9-49
INSPECTION, OIL PRESSURE RELIEF
VALVE .............................9-297
INSPECTION, OIL PUMP....9-107,9-163,9-220,
9-299,9-50
INSPECTION, OIL PUMP . . 21-211,21-382,21-557,
21-728
INSPECTION, OTHER..................30-15
INSPECTION, OVERDRIVE UNIT . . 21-224,21-394,
21-569,21-741
INSPECTION, OVERRUNNING CLUTCH
CAM/OVERDRIVE PISTON RETAINER....21-236,
21-406,21-580,21-752
INSPECTION, PARKING BRAKE..........30-17
INSPECTION, PISTON & CONNECTING
ROD ............9-154,9-209,9-285,9-41,9-98
INSPECTION, PLANETARY GEARTRAIN/
OUTPUT SHAFT . . . 21-241,21-411,21-587,21-760
INSPECTION, PUSHRODS..............9-250
INSPECTION, RADIATOR - 3.9L/5.2L/5.9L . . . 7-61
INSPECTION, RADIATOR - 5.9L DIESEL....7-65
INSPECTION, RADIATOR - 8.0L..........7-62
INSPECTION, RADIATOR FAN -
3.9L/5.2L/5.9L/8.0L....................7-43
INSPECTION, RADIATOR FAN - 5.9L
DIESEL.............................7-44
INSPECTION, RADIATOR PRESSURE CAP . . . 7-66
INSPECTION, RADIO..................30-17
INSPECTION, REAR CLUTCH....21-248,21-419,
21-593,21-765
INSPECTION, RECEIVING...............30-3
INSPECTION, ROCKER ARM / ADJUSTER
ASSY..............................9-262
INSPECTION, SEAT BELTS, SHOULDER
BELTS, RETRACTORS AND HEAD
RESTRAINTS........................30-12
INSPECTION, SEATS..................30-13
INSPECTION, SERVICE BRAKES.........30-17
INSPECTION, SHIFT/CLUTCH INTERLOCK
SYSTEM............................30-19
INSPECTION, SOLID LIFTERS/TAPPETS . . . 9-281
INSPECTION, SPEED CONTROL.........30-17
INSPECTION, SQUEAKS, RATTLES AND
WIND NOISE........................30-15
INSPECTION, STEERING AND HANDLING
. . 30-15
INSPECTION, TAILPIPE - 3.9L/5.2L/5.9L
. . . 11-11
INSPECTION, TAILPIPE - 5.9L DIESEL
....11-12
INSPECTION, TAILPIPE - 5.9L HEAVY
DUTY/8.0L
..........................11-12
INSPECTION, TIRE PRESSURES
..........30-8
INSPECTION, TRANSFER CASE -
NV231HD
..........................21-832
INSPECTION, TRANSFER CASE -
NV241HD
..........................21-902
INSPECTION, TRANSFER CASE -
NV241LD
..........................21-867
INSPECTION, TRANSMISSION
.....21-109,21-64
INSPECTION, TRANSMISSION/TRANSFER
CASE
..............................30-15
INSPECTION, TRIP COMPUTER/
MAINTENANCE REMINDER
.............30-17
INSPECTION, TURBOCHARGER
..........11-16
INSPECTION, TURN AND EMERGENCY
SIGNALS
...........................30-19INSPECTION, VALVE BODY......21-293,21-465,
21-637,21-809
INSPECTION, VIBRATION DAMPER.......9-289
INSPECTION, VISUAL..................30-8
INSPECTION, WATER PUMP -
3.9L/5.2L/5.9L........................7-69
INSPECTION, WATER PUMP - 5.9L
DIESEL.............................7-73
INSPECTION, WATER PUMP - 8.0L........7-72
INSPECTION, WHEEL CYLINDERS........5-31
INSPECTION, WINDOWS, DOORS AND
LOCKS.............................30-14
INSPECTION WINDSHIELD WIPERS/
WASHERS, ROAD TEST................30-18
INSPECTION, WIPER & WASHER
SYSTEM............................8R-6
INSPECTION, WIRING..................30-7
INSTALLED - INSTALLATION, FRONT OIL
SEAL - FRONT COVER.................9-205
INSTALLED - REMOVAL, FRONT OIL
SEAL - FRONT COVER.................9-204
INSTRUMENT CLUSTER - ASSEMBLY.....8J-13
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-2
INSTRUMENT CLUSTER - DIAGNOSIS
AND TESTING........................8J-6
INSTRUMENT CLUSTER - DISASSEMBLY . . 8J-11
INSTRUMENT CLUSTER - INSTALLATION . . 8J-14
INSTRUMENT CLUSTER - OPERATION.....8J-3
INSTRUMENT CLUSTER - REMOVAL.....8J-10
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-10
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-9
INSTRUMENT PANEL DEMISTER DUCTS
- REMOVAL.........................24-37
INSTRUMENT PANEL DUCTS - REMOVAL . 24-37
INSTRUMENT PANEL SYSTEM -
DESCRIPTION......................23-104
INSTRUMENT PANEL SYSTEM -
INSTALLATION......................23-107
INSTRUMENT PANEL SYSTEM -
OPERATION........................23-105
INSTRUMENT PANEL SYSTEM -
REMOVAL.........................23-106
INSTRUMENT PANEL TOP COVER -
INSTALLATION......................23-115
INSTRUMENT PANEL TOP COVER -
REMOVAL.........................23-114
INTAKE AIR HEATER - DESCRIPTION....14-100
INTAKE AIR HEATER - INSTALLATION....14-101
INTAKE AIR HEATER - OPERATION......14-100
INTAKE AIR HEATER - REMOVAL.......14-100
INTAKE AIR HEATER RELAY -
DESCRIPTION......................14-101
INTAKE AIR HEATER RELAY -
INSTALLATION......................14-102
INTAKE AIR HEATER RELAY -
OPERATION........................14-102
INTAKE AIR HEATER RELAY - REMOVAL . 14-102
INTAKE MANIFOLD - CLEANING
....9-110,9-166,
9-223,9-302,9-53
INTAKE MANIFOLD - DESCRIPTION
. 9-109,9-165,
9-222,9-52
INTAKE MANIFOLD - INSPECTION
. . 9-110,9-166,
9-223,9-302,9-53
INTAKE MANIFOLD - INSTALLATION
.....9-111,
9-166,9-223,9-302,9-53
INTAKE MANIFOLD - OPERATION
. . 9-109,9-165,
9-52
INTAKE MANIFOLD - REMOVAL
....9-110,9-166,
9-222,9-301,9-53
INTAKE MANIFOLD LEAKAGE -
DIAGNOSIS AND TESTING
. . . 9-110,9-165,9-222,
9-53
INTAKE/EXHAUST VALVES & SEATS -
CLEANING
.............9-140,9-198,9-27,9-84
INTAKE/EXHAUST VALVES & SEATS -
DESCRIPTION
.....9-138,9-195,9-25,9-253,9-81
INTAKE/EXHAUST VALVES & SEATS -
INSPECTION
...........9-141,9-198,9-27,9-84
INTAKE/EXHAUST VALVES & SEATS -
INSTALLATION
.........9-141,9-260,9-28,9-85
INTAKE/EXHAUST VALVES & SEATS -
REMOVAL
.............9-140,9-258,9-27,9-84
INTAKE/EXHAUST VALVES & SEATS -
STANDARD PROCEDURE-
VALVES,GUIDES AND SPRINGS
.........9-253
BR/BEINDEX 19
Description Group-Page Description Group-Page Description Group-Page
Page 2868 of 2889
LEVEL SWITCH - DESCRIPTION,
WASHER FLUID......................8R-7
LEVEL SWITCH - INSTALLATION,
WASHER FLUID......................8R-8
LEVEL SWITCH - OPERATION, WASHER
FLUID..............................8R-7
LEVEL SWITCH - REMOVAL, WASHER
FLUID..............................8R-8
LEVELS - INSPECTION, FLUID...........30-4
LEVER - ADJUSTMENT, SHIFT . . . 21-853,21-888,
21-925
LEVER - INSTALLATION, GEAR SHIFT.....19-13
LEVER - INSTALLATION, SHIFT . . 21-853,21-888,
21-924
LEVER - REMOVAL, GEAR SHIFT........19-13
LEVER - REMOVAL, SHIFT......21-852,21-887,
21-924
LICENSE PLATE LAMP - INSTALLATION . . . 8L-22
LICENSE PLATE LAMP - REMOVAL.......8L-22
LICENSE PLATE LAMP UNIT -
INSTALLATION.......................8L-22
LICENSE PLATE LAMP UNIT - REMOVAL . . 8L-22
LID - INSTALLATION, CENTER CONSOLE . 23-132
LID - REMOVAL, CENTER CONSOLE.....23-131
LIFTERS - CLEANING, HYDRAULIC . . 9-152,9-208
LIFTERS - INSTALLATION, HYDRAULIC . . . 9-152,
9-208
LIFTERS - REMOVAL, HYDRAULIC . . 9-152,9-207
LIFTERS (CAM IN BLOCK) - CLEANING,
HYDRAULIC......................9-39,9-96
LIFTERS (CAM IN BLOCK) -
INSTALLATION, HYDRAULIC.........9-39,9-96
LIFTERS (CAM IN BLOCK) - REMOVAL,
HYDRAULIC......................9-39,9-96
LIFTERS/TAPPETS - CLEANING, SOLID....9-281
LIFTERS/TAPPETS - INSPECTION, SOLID . . 9-281
LIFTERS/TAPPETS - INSTALLATION,
SOLID.............................9-281
LIFTERS/TAPPETS - REMOVAL, SOLID....9-280
LIGHT DUTY ENGINE (1500 AND 2500
MODELS EXCEPT 8.0L) MAINTENANCE
SCHEDULES, MAINTENANCE
SCHEDULES..........................0-7
LIGHTER - DIAGNOSIS & TESTING,
CIGAR...........................8W-97-2
LIGHTER OUTLET - DESCRIPTION,
CIGAR...........................8W-97-2
LIGHTER OUTLET - INSTALLATION,
CIGAR...........................8W-97-3
LIGHTER OUTLET - OPERATION, CIGAR . 8W-97-2
LIGHTER OUTLET - REMOVAL, CIGAR . . 8W-97-3
LIGHTS - INSPECTION, GAUGES/
WARNING..........................30-19
LIGHTS AND SWITCHES - INSPECTION . . . 30-12
LINE - INSTALLATION, LIQUID..........24-52
LINE - INSTALLATION, SUCTION AND
DISCHARGE.........................24-51
LINE - REMOVAL, LIQUID..............24-52
LINE - REMOVAL, SUCTION AND
DISCHARGE.........................24-50
LINE COUPLERS - DESCRIPTION, A/C....24-40
LINE COUPLERS - OPERATION, A/C......24-41
LINE COUPLERS - STANDARD
PROCEDURE, A/C....................24-43
LINE LEAKS - DIAGNOSIS AND TESTING,
HIGH-PRESSURE FUEL................14-74
LINER - INSTALLATION, REAR
WHEELHOUSE.......................23-96
LINER - REMOVAL, REAR WHEELHOUSE . . 23-96
LINES - CLEANING AND INSPECTION,
OIL COOLER........................9-296
LINES - DESCRIPTION, FUEL.......14-73,14-9
LINES - DESCRIPTION, HIGH PRESSURE
FUEL..............................14-74
LINES - INSTALLATION, FUEL...........14-77
LINES - OPERATION, HIGH PRESSURE
FUEL..............................14-74
LINES - REMOVAL, FUEL..............14-75
LINES/HOSES - INSPECTION.............30-6
LINK CONNECTOR - DESCRIPTION, DATA . 8E-12
LINK CONNECTOR - OPERATION, DATA . . . 8E-12
LINKAGE - 2WD - DESCRIPTION........19-38
LINKAGE - 2WD - INSTALLATION........19-39
LINKAGE - 2WD - REMOVAL
............19-38
LINKAGE - 4WD - DESCRIPTION
........19-40
LINKAGE - 4WD - INSTALLATION
........19-41
LINKAGE - 4WD - REMOVAL
............19-40
LINKAGE - DESCRIPTION
...............6-19LINKAGE - INSTALLATION...............6-20
LINKAGE - OPERATION.................6-20
LINKAGE - REMOVAL..................6-20
LINKAGE, SPECIAL TOOLS - STEERING . . . 19-39,
19-42
LINK/COIL SUSPENSION - STANDARD
PROCEDURES, ALIGNMENT..............2-5
LINK/COIL SUSPENSION, SPECIAL
TOOLS..............................2-16
LIQUID LINE - INSTALLATION...........24-52
LIQUID LINE - REMOVAL..............24-52
LOAD TEST - STANDARD PROCEDURE....8F-14
LOADS - STANDARD PROCEDURE,
TESTING FOR SHORT TO GROUND ON
FUSES POWERING SEVERAL.........8W-01-7
LOCATIONS - DESCRIPTION, SPLICE . . . 8W-95-1
LOCATIONS, SPECIFICATIONS - BODY
SEALER............................23-47
LOCATIONS, SPECIFICATIONS -
STRUCTURAL ADHESIVE...............23-44
LOCATIONS, SPECIFICATIONS - WELD.....23-4
LOCK & REMOTE KEYLESS ENTRY
SYSTEM - DIAGNOSIS AND TESTING,
POWER.............................8N-4
LOCK - STANDARD PROCEDURE,
HYDROSTATIC.....9-11,9-125,9-181,9-238,9-68
LOCK CYLINDER - DIAGNOSIS AND
TESTING, IGNITION SWITCH AND KEY....19-10
LOCK CYLINDER - INSTALLATION.......23-73
LOCK CYLINDER - REMOVAL...........23-73
LOCK CYLINDER HOUSING -
INSTALLATION.......................19-11
LOCK CYLINDER HOUSING - REMOVAL . . . 19-10
LOCK CYLINDERS - DESCRIPTION........23-1
LOCK MOTOR - DESCRIPTION, POWER....8N-6
LOCK MOTOR - DIAGNOSIS AND
TESTING, POWER.....................8N-7
LOCK MOTOR - OPERATION, POWER.....8N-6
LOCK SWITCH - DESCRIPTION, DOOR
CYLINDER...........................8N-5
LOCK SWITCH - DESCRIPTION, POWER . . . 8N-8
LOCK SWITCH - DIAGNOSIS & TESTING,
DOOR CYLINDER.....................8N-5
LOCK SWITCH - DIAGNOSIS AND
TESTING, POWER.....................8N-8
LOCK SWITCH - INSTALLATION, DOOR
CYLINDER...........................8N-6
LOCK SWITCH - OPERATION, DOOR
CYLINDER...........................8N-5
LOCK SWITCH - OPERATION, POWER.....8N-8
LOCK SWITCH - REMOVAL, DOOR
CYLINDER...........................8N-6
LOCK SYSTEM - DESCRIPTION, POWER . . . 8N-1
LOCK SYSTEM - DIAGNOSIS AND
TESTING, POWER.....................8N-4
LOCK SYSTEM - OPERATION, POWER.....8N-3
LOCKS - INSPECTION, DOORS AND
DOOR.............................30-11
LOCKS - INSPECTION, WINDOWS,
DOORS............................30-14
LOOP ADJUSTER - INSTALLATION, SEAT
BELT TURNING......................8O-29
LOOP ADJUSTER - REMOVAL, SEAT
BELT TURNING......................8O-29
LOOP HEIGHT ADJUSTER KNOB -
INSTALLATION, TURNING..............8O-30
LOOP HEIGHT ADJUSTER KNOB -
REMOVAL, TURNING.................8O-30
LOOSE ITEMS - INSTALLATION, SHIPPED . 30-14
LOW FUEL INDICATOR - DESCRIPTION . . . 8J-23
LOW FUEL INDICATOR - OPERATION.....8J-23
LOW MOUNTED - INSTALLATION, SIDE
VIEW MIRROR.......................23-98
LOW MOUNTED - REMOVAL, SIDE VIEW
MIRROR...........................23-98
LOW PRESSURE SWITCH -
DESCRIPTION, A/C...................24-21
LOW PRESSURE SWITCH - DIAGNOSIS
AND TESTING, A/C...................24-21
LOW PRESSURE SWITCH -
INSTALLATION, A/C
...................24-22
LOW PRESSURE SWITCH - OPERATION,
A/C
................................24-21
LOW PRESSURE SWITCH - REMOVAL,
A/C
................................24-21
LOWER - INSTALLATION, LATCH
........23-80
LOWER - INSTALLATION, LATCH
STRIKER
...........................23-82LOWER - REMOVAL, LATCH............23-80
LOWER - REMOVAL, LATCH STRIKER....23-82
LOWER BALL JOINT - DIAGNOSIS AND
TESTING............................2-10
LOWER BALL JOINT - INSTALLATION......2-25
LOWER CONTROL ARM - INSTALLATION . . 2-10,
2-20
LOWER CONTROL ARM - REMOVAL . . 2-10,2-20
LOWER FASCIA - INSTALLATION, FRONT . . . 13-3
LOWER FASCIA - REMOVAL, FRONT......13-3
LUBRICANTS - STANDARD PROCEDURE,
CLASSIFICATION OF....................0-3
LUBRICATION - DESCRIPTION.....9-102,9-158,
9-214,9-292,9-45
LUBRICATION - DIAGNOSIS AND
TESTING...............9-123,9-178,9-66,9-8
LUBRICATION - OPERATION . 9-102,9-158,9-214,
9-292,9-45
LUBRICATION - STANDARD PROCEDURE . 19-38,
19-40
LUMBAR ADJUSTER - DIAGNOSIS &
TESTING, POWER....................8N-18
LUMBAR CONTROL SWITCH -
DESCRIPTION.......................8N-17
LUMBAR CONTROL SWITCH -
OPERATION.........................8N-18
LUMBAR CONTROL SWITCH - REMOVAL . 8N-18
LUMBAR MOTOR - DESCRIPTION.......8N-18
LUMBAR MOTOR - OPERATION.........8N-18
LUMBAR SUPPORT - INSTALLATION....23-133
LUMBAR SUPPORT - REMOVAL........23-133
MACHINING - STANDARD PROCEDURE,
BRAKE DRUM........................5-33
MAIN BEARING CLEARANCE -
STANDARD PROCEDURE...............9-275
MAIN BEARING FITTING - STANDARD
PROCEDURE....................9-203,9-33
MAIN BEARING FITTING - STANDARD
PROCEDURE, CRANKSHAFT........9-146,9-90
MAIN BEARINGS - DESCRIPTION,
CRANKSHAFT...............9-146,9-32,9-90
MAIN BEARINGS - INSTALLATION,
CRANKSHAFT..........9-147,9-204,9-34,9-90
MAIN BEARINGS - OPERATION,
CRANKSHAFT...............9-146,9-32,9-90
MAIN BEARINGS - REMOVAL,
CRANKSHAFT..........9-147,9-204,9-33,9-90
MAINTENANCE SCHEDULE (8.0L 2500 &
3500 MODELS - CALIFORNIA ONLY) -
DESCRIPTION, MEDIUM DUTY TRUCK.....0-13
MAINTENANCE SCHEDULES - 24-VALVE
CUMMINS TURBO DIESEL -
DESCRIPTION........................0-22
MAINTENANCE SCHEDULES -
DESCRIPTION, HEAVY DUTY ENGINE
(FEDERAL ONLY - 2500 8.0L HD AND
3500 5.9L& 8.0L MODELS)..............0-17
MAINTENANCE SCHEDULES - LIGHT
DUTY ENGINE (1500 AND 2500
MODELS EXCEPT 8.0L) MAINTENANCE
SCHEDULES..........................0-7
MAINTENANCE SCHEDULES,
MAINTENANCE SCHEDULES - LIGHT
DUTY ENGINE (1500 AND 2500
MODELS EXCEPT 8.0L)..................0-7
MALFUNCTION INDICATOR LAMP (MIL) -
DESCRIPTION.......................8J-24
MALFUNCTION INDICATOR LAMP (MIL) -
OPERATION.........................8J-24
MANAGER - DESCRIPTION, TASK........25-15
MANAGER - OPERATION, TASK.........25-19
MANIFOLD - CLEANING, EXHAUST . 9-112,9-168,
9-225,9-304,9-55
MANIFOLD - CLEANING, INTAKE . . . 9-110,9-166,
9-223,9-302,9-53
MANIFOLD - DESCRIPTION, EXHAUST . . . 9-112,
9-168,9-224,9-55
MANIFOLD - DESCRIPTION, FUEL DRAIN . . 14-86
MANIFOLD - DESCRIPTION, INTAKE
.....9-109,
9-165,9-222,9-52
MANIFOLD - INSPECTION, EXHAUST
.....9-112,
9-168,9-225,9-304,9-55
MANIFOLD - INSPECTION, INTAKE
. 9-110,9-166,
9-223,9-302,9-53
MANIFOLD - INSTALLATION, EXHAUST
. . . 9-113,
9-168,9-225,9-304,9-55
MANIFOLD - INSTALLATION, FUEL
DRAIN
.............................14-86
BR/BEINDEX 21
Description Group-Page Description Group-Page Description Group-Page