dimensions DODGE RAM 2002 Service Owner's Manual

BODY
TABLE OF CONTENTS
page page
BODY
WARNING
SAFETY PRECAUTIONS AND WARNINGS . . . 1
DIAGNOSIS AND TESTING
DIAGNOSIS AND TESTING - WATER LEAKS . 2
DIAGNOSIS AND TESTING - WIND NOISE . . . 3
SPECIFICATIONS
WELD LOCATIONS.....................4
STRUCTURAL ADHESIVE LOCATIONS.....44
BODY SEALER LOCATIONS.............47
BODY GAP AND FLUSH MEASUREMENTS . . 56
BODY OPENING DIMENSIONS...........60TORQUE SPECIFICATIONS.............61
DECKLID/HATCH/LIFTGATE/TAILGATE.......63
DOOR - FRONT.........................68
DOOR - CARGO.........................77
EXTERIOR.............................86
HOOD................................100
INSTRUMENT PANEL SYSTEM............105
INTERIOR.............................118
PAINT................................129
SEATS...............................131
STATIONARY GLASS....................145
WEATHERSTRIP/SEALS..................151
BODY
WARNING
SAFETY PRECAUTIONS AND WARNINGS
WARNING: USE AN OSHA APPROVED BREATHING
FILTER WHEN SPRAYING PAINT OR SOLVENTS IN
A CONFINED AREA. PERSONAL INJURY CAN
RESULT.
²AVOID PROLONGED SKIN CONTACT WITH
PETROLEUM OR ALCOHOL ± BASED CLEANING
SOLVENTS. PERSONAL INJURY CAN RESULT.
²DO NOT STAND UNDER A HOISTED VEHICLE
THAT IS NOT PROPERLY SUPPORTED ON SAFETY
STANDS. PERSONAL INJURY CAN RESULT.CAUTION: When holes must be drilled or punched
in an inner body panel, verify depth of space to the
outer body panel, electrical wiring, or other compo-
nents. Damage to vehicle can result.
²Do not weld exterior panels unless combustible
material on the interior of vehicle is removed from
the repair area. Fire or hazardous conditions, can
result.
²Always have a fire extinguisher ready for use
when welding.
²Disconnect the negative (-) cable clamp from
the battery when servicing electrical components
that are live when the ignition is OFF. Damage to
electrical system can result.
²Do not use abrasive chemicals or compounds
on painted surfaces. Damage to finish can result.
²Do not use harsh alkaline based cleaning sol-
vents on painted or upholstered surfaces. Damage
to finish or color can result.
²Do not hammer or pound on plastic trim panel
when servicing interior trim. Plastic panels can
break.
BR/BEBODY 23 - 1

BODY OPENING DIMENSIONS
WINDSHIELD OPENING
DOOR OPENING - REGULAR CAB
BACKLITE OPENING
DOOR OPENING - QUAD CAB
23 - 60 BODYBR/BE
BODY (Continued)

NOTE: The air gap is determined by the spacer
shims. When installing an original, or a new clutch
assembly, try the original shims first. When install-
ing a new clutch onto a compressor that previously
did not have a clutch, use 1.0, 0.50, and 0.13 milli-
meter (0.040, 0.020, and 0.005 inch) shims from the
clutch hardware package that is provided with the
new clutch.
(12) On models with the diesel engine option,
install the compressor on the engine. (Refer to 24 -
HEATING & AIR CONDITIONING/PLUMBING/A/C
COMPRESSOR - INSTALLATION)
(13) Connect the battery negative cable.
A/C COMPRESSOR CLUTCH
RELAY
DESCRIPTION
The a/c compressor clutch relay is a International
Standards Organization (ISO) micro-relay. The termi-
nal designations and functions are the same as a con-
ventional ISO relay. However, the micro-relay
terminal orientation (footprint) is different, the cur-
rent capacity is lower, and the relay case dimensions
are smaller than those of the conventional ISO relay.
OPERATION
The compressor clutch relay is a electromechanical
device that switches battery current to the compres-
sor clutch coil when the Powertrain Control Module
(PCM) grounds the coil side of the relay. The PCM
responds to inputs from the a/c heater control, the a/closs of charge switch, the a/c pressure transducer and
the evaporator fin probe.
The compressor clutch relay is located in the Power
Distribution Center (PDC) in the engine compart-
ment. Refer to the PDC label for relay identification
and location.
The compressor clutch relay cannot be repaired
and, if faulty or damaged, it must be replaced.
DIAGNOSIS AND TESTING - A/C COMPRESSOR
CLUTCH RELAY
RELAY TEST
The compressor clutch relay (Fig. 16) is located in
the Power Distribution Center (PDC). Refer to the
PDC label for relay identification and location.
Remove the relay from the PDC to perform the fol-
lowing tests:
(1) A relay in the de-energized position should
have continuity between terminals 87A and 30, and
no continuity between terminals 87 and 30. If OK, go
to Step 2. If not OK, replace the faulty relay.
(2) Resistance between terminals 85 and 86 (elec-
tromagnet) should be 75   5 ohms. If OK, go to Step
3. If not OK, replace the faulty relay.
(3) Connect a battery to terminals 85 and 86.
There should now be continuity between terminals
30 and 87, and no continuity between terminals 87A
and 30. If OK, see the Relay Circuit Test below. If not
OK, replace the faulty relay.
RELAY CIRCUIT TEST
For circuit descriptions and diagrams, (Refer to
Appropriate Wiring Information).
Fig. 15 CHECK CLUTCH AIR GAP
1 - FEELER GAUGE
Fig. 16 COMPRESSOR CLUTCH RELAY
TERMINAL LEGEND
NUMBER IDENTIFICATION
30 COMMON FEED
85 COIL GROUND
86 COIL BATTERY
87 NORMALLY OPEN
87A NORMALLY CLOSED
BR/BECONTROLS 24 - 17
A/C COMPRESSOR CLUTCH (Continued)

BLOCK - DIAGNOSIS AND TESTING,
JUNCTION........................8W-97-7
BLOCK - INSPECTION, ENGINE.......9-27,9-85
BLOCK HEATER - 5.9L - DESCRIPTION,
ENGINE.............................7-44
BLOCK HEATER - 5.9L - INSTALLATION,
ENGINE.............................7-44
BLOCK HEATER - 5.9L - OPERATION,
ENGINE.............................7-44
BLOCK HEATER - 5.9L - REMOVAL,
ENGINE.............................7-44
BLOCK HEATER - 5.9L DIESEL -
DESCRIPTION, ENGINE.................7-46
BLOCK HEATER - 5.9L DIESEL -
INSTALLATION, ENGINE................7-46
BLOCK HEATER - 5.9L DIESEL -
OPERATION, ENGINE...................7-46
BLOCK HEATER - 5.9L DIESEL -
REMOVAL, ENGINE....................7-46
BLOCK HEATER - 8.0L - DESCRIPTION,
ENGINE.............................7-45
BLOCK HEATER - 8.0L - INSTALLATION,
ENGINE.............................7-45
BLOCK HEATER - 8.0L - OPERATION,
ENGINE.............................7-45
BLOCK HEATER - 8.0L - REMOVAL,
ENGINE.............................7-45
BLOCK REFACING - STANDARD
PROCEDURE, CYLINDER...............9-148
BLOWER MOTOR - DESCRIPTION.......24-31
BLOWER MOTOR - DIAGNOSIS AND
TESTING...........................24-32
BLOWER MOTOR - INSTALLATION........24-32
BLOWER MOTOR - OPERATION.........24-31
BLOWER MOTOR - REMOVAL...........24-32
BLOWER MOTOR RELAY - DESCRIPTION . . 24-22
BLOWER MOTOR RELAY - DIAGNOSIS
AND TESTING.......................24-22
BLOWER MOTOR RELAY -
INSTALLATION.......................24-23
BLOWER MOTOR RELAY - OPERATION . . . 24-22
BLOWER MOTOR RELAY - REMOVAL.....24-23
BLOWER MOTOR RESISTOR BLOCK -
DESCRIPTION.......................24-23
BLOWER MOTOR RESISTOR BLOCK -
DIAGNOSIS AND TESTING.............24-23
BLOWER MOTOR RESISTOR BLOCK -
INSTALLATION.......................24-24
BLOWER MOTOR RESISTOR BLOCK -
OPERATION.........................24-23
BLOWER MOTOR RESISTOR BLOCK -
REMOVAL..........................24-24
BLOWER MOTOR SWITCH -
DESCRIPTION.......................24-24
BLOWER MOTOR SWITCH - DIAGNOSIS
AND TESTING.......................24-25
BLOWER MOTOR SWITCH - OPERATION . . 24-24
BLOWER MOTOR SWITCH - REMOVAL . . . 24-25
BODY - ADJUSTMENTS, VALVE . . 21-257,21-428
BODY - ASSEMBLY, VALVE......21-248,21-420
BODY & CABLE - DESCRIPTION,
ANTENNA...........................8A-4
BODY & CABLE - INSTALLATION,
ANTENNA...........................8A-6
BODY & CABLE - OPERATION, ANTENNA . . . 8A-4
BODY & CABLE - REMOVAL, ANTENNA....8A-6
BODY - CLEANING, VALVE......21-244,21-418
BODY - DESCRIPTION, THROTTLE.......14-47
BODY - DESCRIPTION, VALVE....21-218,21-391
BODY - DISASSEMBLY, VALVE . . . 21-237,21-409
BODY - INSPECTION, VALVE.....21-244,21-419
BODY - INSTALLATION, VALVE . . . 21-256,21-428
BODY - OPERATION, THROTTLE.........14-47
BODY - OPERATION, VALVE.....21-223,21-394
BODY - REMOVAL, VALVE.......21-236,21-407
BODY CODE PLATE - DESCRIPTION.....Intro.-4
BODY GAP AND FLUSH
MEASUREMENTS, SPECIFICATIONS......23-56
BODY OPENING DIMENSIONS,
SPECIFICATIONS.....................23-60
BODY SEALER LOCATIONS,
SPECIFICATIONS
.....................23-47
BODY SIDE MOLDINGS - INSTALLATION
. . 23-87
BODY SIDE MOLDINGS - REMOVAL
......23-86
BODY STRIPES AND DECALS -
INSTALLATION
.......................23-87
BODY STRIPES AND DECALS -
REMOVAL
..........................23-87BODY VENT - INSTALLATION..........23-126
BODY VENT - REMOVAL..............23-126
BOOST PRESSURE - DIAGNOSIS AND
TESTING...........................14-93
BOOST PRESSURE - DIAGNOSIS AND
TESTING, TURBOCHARGER.............11-13
BOOSTER - DIAGNOSIS AND TESTING,
HYDRAULIC..........................5-18
BOOSTER - DIAGNOSIS AND TESTING,
MASTER CYLINDER/POWER.............5-26
BOOSTER - INSTALLATION, POWER
BRAKE..............................5-19
BOOSTER - REMOVAL, POWER BRAKE....5-19
BOOT - INSTALLATION, 4WD FLOOR
SHIFT.............................23-122
BOOT - MANUAL TRANSMISSION -
INSTALLATION, SHIFT................23-122
BOOT - MANUAL TRANSMISSION -
REMOVAL, SHIFT....................23-122
BOOT - REMOVAL, 4WD FLOOR SHIFT . . . 23-122
BORE - DE-GLAZE - STANDARD
PROCEDURE, CYLINDER...............9-148
BORE HONING - STANDARD
PROCEDURE, CYLINDER............9-11,9-65
BORE REPAIR - STANDARD
PROCEDURE, CAM...................9-151
BORE REPAIR - STANDARD
PROCEDURE, CYLINDER...............9-149
BOX - ASSEMBLY, GLOVE.............23-111
BOX - DISASSEMBLY, GLOVE..........23-110
BOX - INSTALLATION, CARGO..........23-97
BOX - REMOVAL, CARGO..............23-97
BOX LAMP AND SWITCH -
INSTALLATION, GLOVE................8L-36
BOX LAMP AND SWITCH - REMOVAL,
GLOVE.............................8L-35
BOX LATCH STRIKER - INSTALLATION,
GLOVE............................23-112
BOX LATCH STRIKER - REMOVAL,
GLOVE............................23-111
BOX OPENING UPPER TRIM -
INSTALLATION, GLOVE...............23-112
BOX OPENING UPPER TRIM - REMOVAL,
GLOVE............................23-112
B-PILLAR DOOR SEAL - INSTALLATION . . 23-151
B-PILLAR DOOR SEAL - REMOVAL......23-151
B-PILLAR TRIM - INSTALLATION.......23-120
B-PILLAR TRIM - REMOVAL...........23-120
BRACKET - INSTALLATION, CAB
CHASSIS ADAPTER...................13-10
BRACKET - INSTALLATION, REARVIEW
MIRROR SUPPORT..................23-126
BRACKET - REMOVAL, CAB CHASSIS
ADAPTER...........................13-10
BRAKE - DESCRIPTION, CONTROLLER
ANTILOCK..........................8E-11
BRAKE - DESCRIPTION, PARKING........5-28
BRAKE - INSTALLATION, CONTROLLER
ANTILOCK..........................8E-12
BRAKE - OPERATION, CONTROLLER
ANTILOCK..........................8E-11
BRAKE - OPERATION, PARKING..........5-28
BRAKE - REMOVAL, CONTROLLER
ANTILOCK..........................8E-11
BRAKE BOOSTER - INSTALLATION,
POWER.............................5-19
BRAKE BOOSTER - REMOVAL, POWER....5-19
BRAKE CABLE - INSTALLATION, FRONT
PARKING............................5-30
BRAKE CABLE - INSTALLATION, REAR
PARK...............................5-30
BRAKE CABLE - REMOVAL, FRONT
PARKING............................5-29
BRAKE CABLE - REMOVAL, REAR PARK . . . 5-29
BRAKE CALIPERS - DESCRIPTION, DISC . . . 5-10
BRAKE CALIPERS - OPERATION, DISC.....5-10
BRAKE FLUID CONTAMINATION -
DIAGNOSIS AND TESTING..............5-15
BRAKE FLUID LEVEL - STANDARD
PROCEDURE.........................5-15
BRAKE FLUID, SPECIFICATIONS
..........5-15
BRAKE INDICATOR - DESCRIPTION,
BRAKE/PARK
........................8J-15
BRAKE INDICATOR - DIAGNOSIS AND
TESTING
...........................8J-16
BRAKE INDICATOR - OPERATION,
BRAKE/PARK
........................8J-15
BRAKE LAMP SWITCH - DESCRIPTION
....8L-4BRAKE LAMP SWITCH - DIAGNOSIS
AND TESTING........................8L-5
BRAKE LAMP SWITCH - INSTALLATION....8L-6
BRAKE LAMP SWITCH - OPERATION......8L-4
BRAKE LAMP SWITCH - REMOVAL.......8L-5
BRAKE ROTOR, DIAGNOSIS AND
TESTING - DISC......................5-20
BRAKE SHOES - ADJUSTMENT, PARKING . . 5-33
BRAKE, SPECIFICATIONS - BASE..........5-2
BRAKE SYSTEM - DIAGNOSIS AND
TESTING, BASE........................5-5
BRAKE SYSTEM - STANDARD
PROCEDURE, BLEEDING ABS............5-36
BRAKE/PARK BRAKE INDICATOR -
DESCRIPTION.......................8J-15
BRAKE/PARK BRAKE INDICATOR -
OPERATION.........................8J-15
BRAKES - ABS - DESCRIPTION...........5-35
BRAKES - ABS - OPERATION............5-36
BRAKES - DIAGNOSIS AND TESTING,
ANTILOCK...........................5-36
BRAKES, SPECIAL TOOLS - BASE.........5-4
BR/BE PAINT COLOR CODES,
SPECIFICATIONS - 2002..............23-129
BREAKER - DESCRIPTION, CIRCUIT....8W-97-4
BREAKER - DIAGNOSIS AND TESTING,
CIRCUIT.........................8W-97-4
BREAK-IN - STANDARD PROCEDURE,
A/C COMPRESSOR CLUTCH............24-13
BREATHER VAPOR CANISTER -
INSTALLATION, CRANKCASE.............9-126
BREATHER VAPOR CANISTER -
REMOVAL, CRANKCASE...............9-125
BUCKLE - INSTALLATION, FRONT SEAT
BELT ..............................8O-20
BUCKLE - INSTALLATION, REAR SEAT
BELT ..............................8O-27
BUCKLE - REMOVAL, FRONT SEAT BELT . . 8O-20
BUCKLE - REMOVAL, REAR SEAT BELT . . . 8O-27
BUMPER - INSTALLATION, FRONT........13-4
BUMPER - INSTALLATION, REAR.........13-6
BUMPER - INSTALLATION, SLAM........23-67
BUMPER - REMOVAL, FRONT............13-4
BUMPER - REMOVAL, REAR.............13-6
BUMPER - REMOVAL, SLAM...........23-67
BUMPER - SPORT - INSTALLATION,
FRONT..............................13-5
BUMPER - SPORT - REMOVAL, FRONT....13-5
BUMPERS - DESCRIPTION..............13-1
BURNT FLUID - DIAGNOSIS AND
TESTING, CAUSES OF..........21-157,21-327
BUS - DESCRIPTION, CCD DATA..........8E-6
BUS - DIAGNOSIS AND TESTING, CCD
DATA ..............................8E-11
BUS - OPERATION, CCD DATA...........8E-7
BUSHING - INSTALLATION,
DISTRIBUTOR........................9-35
BUSHING - INSTALLATION, EXTENSION
HOUSING....................21-156,21-326
BUSHING - REMOVAL, DISTRIBUTOR......9-35
BUSHING - REMOVAL, EXTENSION
HOUSING....................21-156,21-326
BUSHING AND SEAL - INSTALLATION,
EXTENSION HOUSING..........21-460,21-497
BUSHING AND SEAL - REMOVAL,
EXTENSION HOUSING..........21-460,21-497
BUSHINGS - INSTALLATION.............2-27
BUSHINGS - REMOVAL.................2-27
BYPASS HOSE WITH AIR CONDITIONING
- INSTALLATION, WATER PUMP..........7-76
BYPASS HOSE WITH AIR CONDITIONING
- REMOVAL, WATER PUMP..............7-73
BYPASS HOSE WITHOUT AIR
CONDITIONING - INSTALLATION,
WATER PUMP........................7-77
BYPASS HOSE WITHOUT AIR
CONDITIONING - REMOVAL, WATER
PUMP..............................7-76
CAB - INSTALLATION, CLUB/QUAD.......8O-20
CAB - INSTALLATION, STANDARD.......8O-19
CAB - REMOVAL, CLUB/QUAD
..........8O-19
CAB - REMOVAL, STANDARD
...........8O-18
CAB CHASSIS ADAPTER BRACKET -
INSTALLATION
.......................13-10
CAB CHASSIS ADAPTER BRACKET -
REMOVAL
..........................13-10
CAB SIDE PANEL SPEAKER -
INSTALLATION, REAR
.................8A-20
4 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

DIESEL - INSTALLATION, WATER PUMP -
5.9L................................7-72
DIESEL - OPERATION.................8E-18
DIESEL - OPERATION.................25-20
DIESEL - OPERATION..........14-106,14-108
DIESEL - OPERATION...................8I-6
DIESEL - OPERATION, BELT
TENSIONERS - 5.9L...................7-23
DIESEL - OPERATION, COOLANT
RECOVERY CONTAINER - 3.9L/5.2L/
5.9L/5.9L............................7-40
DIESEL - OPERATION, ENGINE BLOCK
HEATER - 5.9L........................7-46
DIESEL - OPERATION, ENGINE COOLANT
THERMOSTAT - 5.9L...................7-53
DIESEL - OPERATION, FAN DRIVE
VISCOUS CLUTCH - 5.9L...............7-56
DIESEL - OPERATION, NON-MONITORED
CIRCUITS...........................25-24
DIESEL - OPERATION, RADIATOR - 5.9L . . . 7-62
DIESEL - OPERATION, TRANS COOLER -
5.9L................................7-84
DIESEL - OPERATION, VACUUM PUMP -
5.9L................................7-34
DIESEL - OPERATION, WATER PUMP -
5.9L................................7-72
DIESEL - REMOVAL............14-107,14-108
DIESEL - REMOVAL....................8I-7
DIESEL - REMOVAL, BELT TENSIONERS -
5.9L................................7-23
DIESEL - REMOVAL, COOLANT
RECOVERY CONTAINER - 3.9L/5.2L/
5.9L/5.9L............................7-40
DIESEL - REMOVAL, DRIVE BELTS - 5.9L . . 7-32
DIESEL - REMOVAL, ENGINE BLOCK
HEATER - 5.9L........................7-46
DIESEL - REMOVAL, ENGINE COOLANT
THERMOSTAT - 5.9L...................7-54
DIESEL - REMOVAL, EXHAUST PIPE -
5.9L................................11-9
DIESEL - REMOVAL, MUFFLER - 5.9L.....11-11
DIESEL - REMOVAL, RADIATOR - 5.9L.....7-62
DIESEL - REMOVAL, RADIATOR FAN -
5.9L................................7-43
DIESEL - REMOVAL, TAILPIPE - 5.9L.....11-12
DIESEL - REMOVAL, VACUUM PUMP -
5.9L................................7-34
DIESEL - REMOVAL, WATER PUMP -
5.9L................................7-72
DIESEL ENGINE - DESCRIPTION, FUEL
REQUIREMENTS.......................0-3
DIESEL ENGINE - DIAGNOSIS AND
TESTING............................11-4
DIESEL ENGINE - DIAGNOSIS AND
TESTING, COOLING SYSTEM............7-13
DIESEL ENGINE - INSTALLATION........19-37
DIESEL ENGINE - REMOVAL............19-36
DIESEL ENGINE - STANDARD
PROCEDURE, DRAINING COOLING
SYSTEM 5.9L........................7-15
DIESEL ENGINE - STANDARD
PROCEDURE, REFILLING COOLING
SYSTEM 5.9L........................7-16
DIESEL ENGINE - TORQUE.............14-94
DIESEL ENGINE, SPECIAL TOOLS - 5.9L . . 9-128
DIESEL ENGINES - DESCRIPTION,
COMPONENT MONITORS
..............25-20
DIESEL ENGINES - FUEL SYSTEM
PRESSURES
........................14-62
DIESEL FUEL DELIVERY SYSTEM -
DESCRIPTION
.......................14-55
DIESEL FUEL INJECTION SYSTEM -
DESCRIPTION
.......................14-91
DIESEL FUEL SYSTEM, SPECIAL TOOLS
. . 14-63
DIESEL FUEL TANK - DESCRIPTION
......14-82
DIESEL, SPECIFICATIONS - 5.9L
.........9-127
DIESEL WITH AUTO. TRANS. -
INSTALLATION
..................8P-12,8P-6
DIESEL WITH AUTO. TRANS. -
REMOVAL
.......................8P-5,8P-9
DIFFERENTIAL - ASSEMBLY
....3-126,3-38,3-66,
3-97
DIFFERENTIAL - DISASSEMBLY
. 3-126,3-38,3-65,
3-97
DIFFERENTIAL - INSTALLATION
. 3-126,3-39,3-66,
3-97
DIFFERENTIAL - POWR-LOK - ASSEMBLY
. . 3-99DIFFERENTIAL - POWR-LOK -
DISASSEMBLY........................3-99
DIFFERENTIAL - REMOVAL . 3-125,3-37,3-64,3-96
DIFFERENTIAL - TRAC-LOK - ASSEMBLY . . 3-129,
3-70
DIFFERENTIAL - TRAC-LOK -
DISASSEMBLY...................3-128,3-68
DIFFERENTIAL CASE BEARINGS -
INSTALLATION.........3-102,3-129,3-41,3-72
DIFFERENTIAL CASE BEARINGS -
REMOVAL.............3-102,3-129,3-40,3-72
DIMENSION, SPECIFICATIONS - FRAME....13-8
DIMENSIONS, SPECIFICATIONS - BODY
OPENING...........................23-60
DIODE - INSTALLATION............8W-01-13
DIODE - REMOVAL................8W-01-13
DIODE REPLACEMENT - STANDARD
PROCEDURE.........................24-7
DISASSEMBLY - OVERHEAD CONSOLE
DISASSEMBLY.......................8M-7
DISASSEMBLY, AXLE VACUUM MOTOR....3-34
DISASSEMBLY, DIAGNOSIS AND
TESTING....................21-115,21-287
DISASSEMBLY, DIFFERENTIAL . . 3-126,3-38,3-65,
3-97
DISASSEMBLY, DIFFERENTIAL -
POWR-LOK..........................3-99
DISASSEMBLY, DIFFERENTIAL -
TRAC-LOK......................3-128,3-68
DISASSEMBLY, DISASSEMBLY -
OVERHEAD CONSOLE.................8M-7
DISASSEMBLY, DOUBLE CARDAN
UNIVERSAL JOINTS...................3-10
DISASSEMBLY, DRIVER AIRBAG.........8O-15
DISASSEMBLY, FLYWHEEL..............6-13
DISASSEMBLY, FRONT CLUTCH . . 21-161,21-331
DISASSEMBLY, FRONT SERVO . . . 21-164,21-334
DISASSEMBLY, GLOVE BOX...........23-110
DISASSEMBLY, HVAC HOUSING.........24-35
DISASSEMBLY, INSTRUMENT CLUSTER . . . 8J-10
DISASSEMBLY, MANUAL - NV4500........21-5
DISASSEMBLY, MANUAL - NV5600.......21-49
DISASSEMBLY, OIL PUMP...............9-47
DISASSEMBLY, OIL PUMP.......21-167,21-337
DISASSEMBLY, OVERDRIVE UNIT . 21-173,21-346
DISASSEMBLY, OVERRUNNING CLUTCH
CAM/OVERDRIVE PISTON RETAINER....21-192,
21-364
DISASSEMBLY, PLANETARY GEARTRAIN/
OUTPUT SHAFT...............21-198,21-369
DISASSEMBLY, REAR CLUTCH . . . 21-204,21-376
DISASSEMBLY, REAR SERVO....21-207,21-378
DISASSEMBLY, REMOVAL...............5-11
DISASSEMBLY, SINGLE CARDAN
UNIVERSAL JOINTS....................3-8
DISASSEMBLY, STANDARD PROCEDURE . . . 7-80
DISASSEMBLY, TRANSFER CASE -
NV241HD..........................21-469
DISASSEMBLY, TRANSFER CASE -
NV241LD..........................21-432
DISASSEMBLY, VALVE BODY.....21-237,21-409
DISC - INSTALLATION, CLUTCH...........6-8
DISC - REMOVAL, CLUTCH...............6-7
DISC BRAKE CALIPERS - DESCRIPTION....5-10
DISC BRAKE CALIPERS - OPERATION.....5-10
DISC BRAKE ROTOR, DIAGNOSIS AND
TESTING............................5-20
DISCHARGE (ESD) SENSITIVE DEVICES -
STANDARD PROCEDURE,
ELECTROSTATIC...................8W-01-8
DISCHARGE LINE - INSTALLATION,
SUCTION...........................24-52
DISCHARGE LINE - REMOVAL, SUCTION . . 24-51
DISPLAY TEST MODE - DESCRIPTION,
STATE ..............................25-1
DISTRIBUTION - DESCRIPTION, POWER . 8W-97-1
DISTRIBUTION - OPERATION, POWER . . 8W-97-1
DISTRIBUTION CENTER - DESCRIPTION,
POWER..........................8W-97-8
DISTRIBUTION CENTER - INSTALLATION,
POWER
.........................8W-97-10
DISTRIBUTION CENTER - OPERATION,
POWER
..........................8W-97-8
DISTRIBUTION CENTER - REMOVAL,
POWER
..........................8W-97-8
DISTRIBUTION SYSTEMS, SPECIAL
TOOLS - POWER
...................8W-97-2
DISTRIBUTOR - DESCRIPTION
..........8I-11DISTRIBUTOR - INSTALLATION..........8I-13
DISTRIBUTOR - OPERATION............8I-12
DISTRIBUTOR - REMOVAL..............8I-12
DISTRIBUTOR BUSHING - INSTALLATION . . 9-35
DISTRIBUTOR BUSHING - REMOVAL......9-35
DISTRIBUTOR CAP - DIAGNOSIS AND
TESTING............................8I-14
DISTRIBUTOR ROTOR - DIAGNOSIS AND
TESTING............................8I-14
DOME LAMP - INSTALLATION..........8L-34
DOME LAMP - REMOVAL..............8L-34
DOOR - ADJUSTMENT, CARGO..........23-78
DOOR - INSTALLATION...........23-69,23-78
DOOR - INSTALLATION, BLEND.........24-37
DOOR - INSTALLATION, FUEL FILL.......23-95
DOOR - INSTALLATION, HEAT/DEFROST . . . 24-38
DOOR - INSTALLATION, PANEL/DEFROST . . 24-38
DOOR - INSTALLATION, RECIRCULATION . . 24-39
DOOR - REMOVAL...............23-69,23-78
DOOR - REMOVAL, BLEND.............24-37
DOOR - REMOVAL, FUEL FILL..........23-95
DOOR - REMOVAL, HEAT/DEFROST......24-37
DOOR - REMOVAL, PANEL/DEFROST.....24-38
DOOR - REMOVAL, RECIRCULATION.....24-38
DOOR ACTUATOR - INSTALLATION,
BLEND.............................24-25
DOOR ACTUATOR - INSTALLATION,
HEAT/DEFROST......................24-27
DOOR ACTUATOR - INSTALLATION,
PANEL/DEFROST.....................24-27
DOOR ACTUATOR - INSTALLATION,
RECIRCULATION.....................24-28
DOOR ACTUATOR - REMOVAL, BLEND....24-25
DOOR ACTUATOR - REMOVAL,
HEAT/DEFROST......................24-26
DOOR ACTUATOR - REMOVAL,
PANEL/DEFROST.....................24-26
DOOR ACTUATOR - REMOVAL,
RECIRCULATION.....................24-27
DOOR AJAR SWITCH - DESCRIPTION....8L-34
DOOR AJAR SWITCH - DIAGNOSIS AND
TESTING...........................8L-34
DOOR AJAR SWITCH - INSTALLATION....8L-35
DOOR AJAR SWITCH - REMOVAL........8L-35
DOOR CYLINDER LOCK SWITCH -
DESCRIPTION........................8N-5
DOOR CYLINDER LOCK SWITCH -
DIAGNOSIS AND TESTING..............8N-6
DOOR CYLINDER LOCK SWITCH -
INSTALLATION.......................8N-6
DOOR CYLINDER LOCK SWITCH -
OPERATION..........................8N-5
DOOR CYLINDER LOCK SWITCH -
REMOVAL...........................8N-6
DOOR FORE/AFT - ADJUSTMENT, FRONT . . 23-69
DOOR GLASS - INSTALLATION..........23-70
DOOR GLASS - REMOVAL.............23-70
DOOR GLASS RUN WEATHERSTRIP -
INSTALLATION, FRONT...............23-153
DOOR GLASS RUN WEATHERSTRIP -
REMOVAL, FRONT...................23-152
DOOR INNER BELT WEATHERSTRIP -
INSTALLATION, FRONT...............23-153
DOOR INNER BELT WEATHERSTRIP -
REMOVAL, FRONT...................23-153
DOOR IN/OUT - ADJUSTMENT, FRONT....23-70
DOOR LATCH - ADJUSTMENT, FRONT....23-73
DOOR OPENING SEAL - INSTALLATION . . 23-152
DOOR OPENING SEAL - REMOVAL......23-152
DOOR OUTER BELT WEATHERSTRIP -
INSTALLATION, FRONT...............23-153
DOOR OUTER BELT WEATHERSTRIP -
REMOVAL, FRONT...................23-153
DOOR SEAL - INSTALLATION, B-PILLAR . 23-151
DOOR SEAL - REMOVAL, B-PILLAR.....23-151
DOOR SECOND WEATHERSTRIP -
INSTALLATION, FRONT...............23-154
DOOR SECOND WEATHERSTRIP -
REMOVAL, FRONT...................23-154
DOOR SILL TRIM - INSTALLATION......23-121
DOOR SILL TRIM - REMOVAL.........23-121
DOOR SPEAKER - INSTALLATION, FRONT . 8A-19
DOOR SPEAKER - INSTALLATION, REAR
. . 8A-21
DOOR SPEAKER - REMOVAL, FRONT
.....8A-19
DOOR SPEAKER - REMOVAL, REAR
......8A-20
DOOR UP/DOWN - ADJUSTMENT, FRONT
. 23-70
DOOR UPPER CORNER SEAL -
INSTALLATION, FRONT
...............23-154
10 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

NV241LD - CLEANING, TRANSFER CASE . 21-441
NV241LD - DESCRIPTION, TRANSFER
CASE.............................21-430
NV241LD - DISASSEMBLY, TRANSFER
CASE.............................21-432
NV241LD - INSPECTION, TRANSFER
CASE.............................21-442
NV241LD - INSTALLATION, TRANSFER
CASE.............................21-458
NV241LD - OPERATION, TRANSFER
CASE.............................21-430
NV241LD - REMOVAL, TRANSFER CASE . 21-432
NV241LD - TRANSFER CASE...........21-459
NV4500 - ASSEMBLY, MANUAL.........21-21
NV4500 - CLEANING, MANUAL..........21-20
NV4500 - DESCRIPTION, MANUAL........21-1
NV4500 - DIAGNOSIS AND TESTING,
MANUAL............................21-3
NV4500 - DISASSEMBLY, MANUAL........21-5
NV4500 - INSPECTION, MANUAL........21-20
NV4500 - INSTALLATION, ADAPTER
HOUSING SEAL......................21-42
NV4500 - INSTALLATION, EXTENSION
HOUSING SEAL......................21-42
NV4500 - INSTALLATION, MANUAL......21-37
NV4500 - INSTALLATION, SHIFT COVER . . . 21-45
NV4500 - INSTALLATION, SHIFT
MECHANISM........................21-44
NV4500 - OPERATION, MANUAL..........21-3
NV4500 - REMOVAL, ADAPTER
HOUSING SEAL......................21-42
NV4500 - REMOVAL, EXTENSION
HOUSING SEAL......................21-42
NV4500 - REMOVAL, MANUAL...........21-4
NV4500 - REMOVAL, SHIFT COVER......21-45
NV4500 - REMOVAL, SHIFT MECHANISM . . 21-43
NV4500 - SPECIFICATIONS, MANUAL.....21-38
NV5600 - ASSEMBLY, MANUAL.........21-64
NV5600 - CLEANING, MANUAL..........21-63
NV5600 - DESCRIPTION, MANUAL.......21-46
NV5600 - DIAGNOSIS AND TESTING,
MANUAL...........................21-48
NV5600 - DISASSEMBLY, MANUAL.......21-49
NV5600 - INSPECTION, MANUAL........21-63
NV5600 - INSTALLATION, ADAPTER
HOUSING SEAL......................21-85
NV5600 - INSTALLATION, EXTENSION
HOUSING SEAL......................21-85
NV5600 - INSTALLATION, MANUAL......21-78
NV5600 - INSTALLATION, SHIFT COVER . . . 21-86
NV5600 - OPERATION, MANUAL.........21-48
NV5600 - REMOVAL, ADAPTER
HOUSING SEAL......................21-85
NV5600 - REMOVAL, EXTENSION
HOUSING SEAL......................21-85
NV5600 - REMOVAL, MANUAL..........21-49
NV5600 - REMOVAL, SHIFT COVER......21-86
NV5600 - SPECIFICATIONS, MANUAL.....21-79
O2 SENSOR - DESCRIPTION............14-45
O2 SENSOR - INSTALLATION...........14-47
O2 SENSOR - OPERATION.............14-45
O2 SENSOR - REMOVAL...............14-46
ODOMETER - DESCRIPTION............8J-24
ODOMETER - OPERATION..............8J-24
OFF INDICATOR - DESCRIPTION,
OVERDRIVE.........................8J-26
OFF INDICATOR - OPERATION,
OVERDRIVE.........................8J-26
OIL - DESCRIPTION, ENGINE..........0-4,0-5
OIL - DESCRIPTION, REFRIGERANT......24-57
OIL - OPERATION, REFRIGERANT........24-57
OIL - STANDARD PROCEDURE, ENGINE . . 9-101,
9-45
OIL COOLER - INSTALLATION, AIR TO.....7-87
OIL COOLER & LINES - CLEANING AND
INSPECTION........................9-179
OIL COOLER - REMOVAL, AIR TO.........7-86
OIL COOLER - REMOVAL, WATER TO......7-86
OIL FILTER - INSTALLATION . . . 9-102,9-179,9-46
OIL FILTER - REMOVAL......9-102,9-179,9-46
OIL LEAKS - DIAGNOSIS AND TESTING,
ENGINE
.........................9-43,9-99
OIL LEVEL - STANDARD PROCEDURE,
ENGINE
............................9-178
OIL LEVEL - STANDARD PROCEDURE,
REFRIGERANT
.......................24-57
OIL PAN - CLEANING
........9-103,9-179,9-46
OIL PAN - INSPECTION
.......9-103,9-179,9-46OIL PAN - INSTALLATION.....9-103,9-180,9-46
OIL PAN - REMOVAL.........9-102,9-179,9-46
OIL PRESSURE - DIAGNOSIS AND
TESTING, ENGINE...........9-101,9-178,9-45
OIL PRESSURE GAUGE - DESCRIPTION . . . 8J-25
OIL PRESSURE GAUGE - OPERATION.....8J-25
OIL PRESSURE RELIEF VALVE -
CLEANING..........................9-180
OIL PRESSURE RELIEF VALVE -
INSPECTION........................9-180
OIL PRESSURE RELIEF VALVE -
INSTALLATION.......................9-180
OIL PRESSURE RELIEF VALVE -
REMOVAL..........................9-180
OIL PRESSURE SENSOR/SWITCH -
INSTALLATION.......................9-181
OIL PRESSURE SENSOR/SWITCH -
REMOVAL..........................9-181
OIL PUMP - ASSEMBLY................9-49
OIL PUMP - ASSEMBLY........21-169,21-340
OIL PUMP - CLEANING...........9-104,9-181
OIL PUMP - CLEANING.........21-168,21-338
OIL PUMP - DESCRIPTION......21-166,21-336
OIL PUMP - DISASSEMBLY.............9-47
OIL PUMP - DISASSEMBLY......21-167,21-337
OIL PUMP - INSPECTION.....9-104,9-181,9-47
OIL PUMP - INSPECTION.......21-168,21-339
OIL PUMP - INSTALLATION . . . 9-106,9-182,9-50
OIL PUMP - OPERATION.........21-166,21-336
OIL PUMP - REMOVAL.......9-104,9-181,9-47
OIL PUMP VOLUME CHECK - STANDARD
PROCEDURE.................21-166,21-336
OIL SEAL - FRONT - DESCRIPTION,
CRANKSHAFT........................9-32
OIL SEAL - FRONT - INSTALLATION,
CRANKSHAFT...................9-160,9-32
OIL SEAL - FRONT - OPERATION,
CRANKSHAFT........................9-32
OIL SEAL - FRONT - REMOVAL,
CRANKSHAFT...................9-160,9-32
OIL SEAL - FRONT COVER INSTALLED -
INSTALLATION, FRONT.................9-89
OIL SEAL - FRONT COVER INSTALLED -
REMOVAL, FRONT.....................9-89
OIL SEAL - FRONT COVER REMOVED -
INSTALLATION, FRONT.................9-90
OIL SEAL - FRONT COVER REMOVED -
REMOVAL, FRONT.....................9-89
OIL SEAL - REAR - DESCRIPTION,
CRANKSHAFT........................9-33
OIL SEAL - REAR - INSTALLATION,
CRANKSHAFT...............9-162,9-34,9-90
OIL SEAL - REAR - OPERATION,
CRANKSHAFT........................9-33
OIL SEAL - REAR - REMOVAL,
CRANKSHAFT...............9-161,9-33,9-90
OIL SEAL RETAINER - INSTALLATION,
CRANKSHAFT REAR..............9-163,9-90
OIL SEAL RETAINER - REMOVAL,
CRANKSHAFT REAR..............9-162,9-90
OIL SERVICE - STANDARD PROCEDURE,
ENGINE............................9-178
ON-BOARD DIAGNOSTICS (OBD) -
DIAGNOSIS AND TESTING...............7-5
ONE WAY CHECK VALVE - DESCRIPTION . . 25-31
ONE WAY CHECK VALVE - INSTALLATION . 25-31
ONE WAY CHECK VALVE - OPERATION....25-31
ONE WAY CHECK VALVE - REMOVAL.....25-31
ONE-WAY CHECK VALVE - DIAGNOSIS
AND TESTING.......................25-31
ON/OFF SWITCH - DESCRIPTION,
PASSENGER AIRBAG.................8O-23
ON/OFF SWITCH - INSTALLATION,
PASSENGER AIRBAG.................8O-25
ON/OFF SWITCH - OPERATION,
PASSENGER AIRBAG.................8O-24
ON/OFF SWITCH - REMOVAL,
PASSENGER AIRBAG.................8O-24
OPEN-CIRCUIT VOLTAGE TEST -
STANDARD PROCEDURE...............8F-12
OPENING COVER - INSTALLATION,
STEERING COLUMN
.................23-114
OPENING COVER - REMOVAL, STEERING
COLUMN
..........................23-113
OPENING DIMENSIONS, SPECIFICATIONS
- BODY
............................23-60
OPENING SEAL - INSTALLATION, DOOR
. . 23-152
OPENING SEAL - REMOVAL, DOOR
.....23-152OPENING UPPER TRIM - INSTALLATION,
GLOVE BOX........................23-112
OPENING UPPER TRIM - REMOVAL,
GLOVE BOX........................23-112
ORIFICE TUBE - DESCRIPTION, A/C......24-54
ORIFICE TUBE - DIAGNOSIS AND
TESTING, FIXED.....................24-54
ORIFICE TUBE - INSTALLATION, A/C......24-54
ORIFICE TUBE - OPERATION, A/C........24-54
ORIFICE TUBE - REMOVAL, A/C.........24-54
OUTBOARD IDENTIFICATION LAMP -
INSTALLATION.......................8L-29
OUTBOARD IDENTIFICATION LAMP -
REMOVAL..........................8L-28
OUTER BELT WEATHERSTRIP -
INSTALLATION, FRONT DOOR..........23-153
OUTER BELT WEATHERSTRIP -
REMOVAL, FRONT DOOR.............23-153
OUTLET - DESCRIPTION, CIGAR
LIGHTER.........................8W-97-2
OUTLET - DESCRIPTION, POWER.....8W-97-10
OUTLET - DIAGNOSIS AND TESTING,
CIGAR LIGHTER...................8W-97-2
OUTLET - DIAGNOSIS AND TESTING,
POWER.........................8W-97-10
OUTLET - INSTALLATION, CIGAR
LIGHTER.........................8W-97-4
OUTLET - INSTALLATION, POWER....8W-97-11
OUTLET - OPERATION, CIGAR LIGHTER . 8W-97-2
OUTLET - OPERATION, POWER......8W-97-10
OUTLET - REMOVAL, CIGAR LIGHTER . . . 8W-97-3
OUTLET - REMOVAL, POWER........8W-97-11
OUTLET BARRELS - INSTALLATION,
PANEL.............................24-31
OUTLET BARRELS - REMOVAL, PANEL . . . 24-31
OUTPUT - DESCRIPTION, PCM...........8I-4
OUTPUT - DIAGNOSIS AND TESTING,
VACUUM PUMP.......................7-34
OUTPUT - OPERATION, PCM............14-52
OUTPUT - OPERATION, PCM.............8I-4
OUTPUT SHAFT FRONT BEARING -
INSTALLATION................21-171,21-342
OUTPUT SHAFT FRONT BEARING -
REMOVAL...................21-171,21-342
OUTPUT SHAFT REAR BEARING -
INSTALLATION................21-172,21-343
OUTPUT SHAFT REAR BEARING -
REMOVAL...................21-171,21-343
OUTPUT SHAFT SEAL - INSTALLATION,
FRONT......................21-461,21-498
OUTPUT SHAFT SEAL - REMOVAL,
FRONT......................21-461,21-498
OVERDRIVE CLUTCH - DESCRIPTION . . . 21-172,
21-343
OVERDRIVE CLUTCH - OPERATION.....21-172,
21-343
OVERDRIVE ELECTRICAL CONTROLS -
DIAGNOSIS AND TESTING......21-191,21-344
OVERDRIVE OFF INDICATOR -
DESCRIPTION.......................8J-26
OVERDRIVE OFF INDICATOR -
OPERATION.........................8J-26
OVERDRIVE SWITCH - DESCRIPTION . . . 21-190,
21-344
OVERDRIVE SWITCH - INSTALLATION . . . 21-191,
21-345
OVERDRIVE SWITCH - OPERATION.....21-190,
21-344
OVERDRIVE SWITCH - REMOVAL . 21-191,21-344
OVERDRIVE UNIT - ASSEMBLY . . . 21-180,21-354
OVERDRIVE UNIT - CLEANING . . . 21-179,21-353
OVERDRIVE UNIT - DISASSEMBLY.....21-173,
21-346
OVERDRIVE UNIT - INSPECTION . 21-180,21-353
OVERDRIVE UNIT - INSTALLATION.....21-189,
21-362
OVERDRIVE UNIT - REMOVAL . . . 21-173,21-345
OVERFLOW VALVE - DESCRIPTION......14-87
OVERFLOW VALVE - DIAGNOSIS AND
TESTING...........................14-87
OVERFLOW VALVE - INSTALLATION......14-88
OVERFLOW VALVE - OPERATION
........14-87
OVERFLOW VALVE - REMOVAL
..........14-88
OVERHEAD CONSOLE - DESCRIPTION
....8M-1
OVERHEAD CONSOLE ASSEMBLY,
ASSEMBLY
..........................8M-8
OVERHEAD CONSOLE DISASSEMBLY,
DISASSEMBLY
.......................8M-7
BR/BEINDEX 21
Description Group-Page Description Group-Page Description Group-Page

SPECIFICATIONS - BODY GAP AND
FLUSH MEASUREMENTS...............23-56
SPECIFICATIONS - BODY OPENING
DIMENSIONS........................23-60
SPECIFICATIONS - BODY SEALER
LOCATIONS.........................23-47
SPECIFICATIONS - BRAKE FLUID.........5-15
SPECIFICATIONS - EXTERIOR LAMPS......8L-4
SPECIFICATIONS - FLUID CAPACITIES......0-6
SPECIFICATIONS - FRAME DIMENSION....13-8
SPECIFICATIONS - FUEL INJECTION
PUMP DATA PLATE...................14-77
SPECIFICATIONS - GENERATOR RATINGS . . 8F-26
SPECIFICATIONS - IGNITION TIMING......8I-4
SPECIFICATIONS - INTERIOR LAMPS.....8L-33
SPECIFICATIONS - POWER STEERING
GEAR..............................19-21
SPECIFICATIONS - PROPELLER SHAFT......3-6
SPECIFICATIONS - SPARK PLUG CABLE
RESISTANCE..........................8I-3
SPECIFICATIONS - SPARK PLUGS.........8I-3
SPECIFICATIONS - SPECIAL TOOLS.......8F-7
SPECIFICATIONS - SPECIFICATIONS......24-46
SPECIFICATIONS - STARTING SYSTEM....8F-36
SPECIFICATIONS - STRUCTURAL
ADHESIVE LOCATIONS................23-44
SPECIFICATIONS - TIRE REVOLUTIONS
PER MILE...........................22-9
SPECIFICATIONS - TORQUE.............7-18
SPECIFICATIONS - TORQUE....9-127,9-17,9-71
SPECIFICATIONS - TORQUE.............11-5
SPECIFICATIONS - TORQUE CHART....5-3,5-37
SPECIFICATIONS - TORQUE CHART . 19-21,19-41,
19-43,19-9
SPECIFICATIONS - TORQUE CHART . . . 2-15,2-26,
2-8
SPECIFICATIONS - TORQUE CHART......22-11
SPECIFICATIONS - TORQUE
SPECIFICATIONS.....................23-61
SPECIFICATIONS - TORQUE
SPECIFICATIONS......................24-8
SPECIFICATIONS - TRANSFER CASE....21-458,
21-495
SPECIFICATIONS - TRANSMISSION.....21-144,
21-314
SPECIFICATIONS - WELD LOCATIONS.....23-4
SPECIFICATIONS, CLUTCH...............6-7
SPECIFICATIONS, FUEL SYSTEM
PRESSURE - GAS ENGINES.............14-3
SPECIFICATIONS, MANUAL - NV4500.....21-38
SPECIFICATIONS, MANUAL - NV5600.....21-79
SPECIFICATIONS, SPECIFICATIONS.......24-46
SPECIFICATIONS, SPECIFICATIONS -
TORQUE............................23-61
SPECIFICATIONS, SPECIFICATIONS -
TORQUE............................24-8
SPECIFICATIONS, TORQUE..............13-1
SPECIFICATIONS, TORQUE - FUEL
DELIVERY...........................14-4
SPECIFICATIONS, TORQUE - GAS FUEL
INJECTION..........................14-35
SPECIFICATIONS, TORQUE -
GENERATOR/CHARGING SYSTEM........8F-27
SPECIFICATIONS, TORQUE - IGNITION.....8I-2
SPECIFICATIONS, TORQUE - STARTING
SYSTEM............................8F-37
SPEED CONTROL SERVO - DESCRIPTION . . 8P-6
SPEED CONTROL SERVO - OPERATION....8P-6
SPEED CONTROL SYSTEM -
DESCRIPTION
........................8P-1
SPEED CONTROL SYSTEM - OPERATION
. . . 8P-2
SPEED CONTROL SYSTEM - TORQUE
.....8P-4
SPEED INPUT - DESCRIPTION, VEHICLE
. . . 8P-2
SPEED SENSOR - DESCRIPTION
. . 21-209,21-381
SPEED SENSOR - DESCRIPTION, FRONT
WHEEL
.............................5-38
SPEED SENSOR - DIAGNOSIS AND
TESTING, REAR WHEEL
................5-40
SPEED SENSOR - INSTALLATION, REAR
WHEEL
.............................5-40
SPEED SENSOR - OPERATION
. . . 21-209,21-381
SPEED SENSOR - OPERATION, FRONT
WHEEL
.............................5-38
SPEED SENSOR - REMOVAL, REAR
WHEEL
.............................5-40
SPEEDOMETER - DESCRIPTION
.........8J-29
SPEEDOMETER - OPERATION
...........8J-30SPEEDS - DESCRIPTION, TIRE
PRESSURE FOR HIGH..................22-7
SPLASH SHIELD - INSTALLATION, REAR . . 23-96
SPLASH SHIELD - REMOVAL, REAR......23-96
SPLASH SHIELDS - INSTALLATION,
FRONT END.........................23-92
SPLASH SHIELDS - REMOVAL, FRONT
END ...............................23-92
SPLICE INFORMATION - DESCRIPTION,
CONNECTOR, GROUND..............8W-01-6
SPLICING - STANDARD PROCEDURE,
WIRE...........................8W-01-13
SPLIT BENCH - INSTALLATION, SEAT....23-134
SPLIT BENCH - INSTALLATION, SEAT
BACK.............................23-136
SPLIT BENCH - INSTALLATION, SEAT
BACK COVER.......................23-137
SPLIT BENCH - INSTALLATION, SEAT
CUSHION COVER....................23-140
SPLIT BENCH - INSTALLATION, SEAT
TRACK............................23-142
SPLIT BENCH - REMOVAL, SEAT.......23-133
SPLIT BENCH - REMOVAL, SEAT BACK . . 23-135
SPLIT BENCH - REMOVAL, SEAT BACK
COVER............................23-137
SPLIT BENCH - REMOVAL, SEAT
CUSHION COVER....................23-139
SPLIT BENCH - REMOVAL, SEAT TRACK . 23-142
SPOOL VALVE - INSTALLATION..........19-28
SPOOL VALVE - REMOVAL.............19-26
SPORT - INSTALLATION, FRONT
BUMPER............................13-5
SPORT - INSTALLATION, FRONT FASCIA . . . 13-3
SPORT - REMOVAL, FRONT BUMPER......13-5
SPORT - REMOVAL, FRONT FASCIA.......13-3
SPRING - INSTALLATION.......2-12,2-23,2-28
SPRING - REMOVAL...........2-11,2-23,2-27
SPRING AND SHOCK - DIAGNOSIS AND
TESTING............................2-25
SPRINGS - INSTALLATION, VALVES AND
VALVE ..............................9-84
SPRINGS - REMOVAL, VALVES AND
VALVE ..............................9-82
SPRINGS - STANDARD PROCEDURE,
VALVES, GUIDES......................9-23
SPRINGS - STANDARD PROCEDURE,
VALVES,GUIDES.....................9-138
SPROCKETS - INSTALLATION, TIMING
BELT/CHAIN.....................9-111,9-55
SPROCKETS - REMOVAL, TIMING
BELT/CHAIN.....................9-111,9-54
STABILIZER BAR - INSTALLATION....2-12,2-23,
2-29
STABILIZER BAR - REMOVAL....2-12,2-23,2-29
STANCHION COVER - INSTALLATION....23-143
STANCHION COVER - REMOVAL........23-143
STANDARD CAB - INSTALLATION........8O-19
STANDARD CAB - REMOVAL...........8O-18
STARTER MOTOR - DESCRIPTION.......8F-37
STARTER MOTOR - DIAGNOSIS AND
TESTING...........................8F-38
STARTER MOTOR - INSTALLATION.......8F-40
STARTER MOTOR - OPERATION.........8F-37
STARTER MOTOR - REMOVAL..........8F-38
STARTER MOTOR RELAY - DESCRIPTION . 8F-41
STARTER MOTOR RELAY -
INSTALLATION.......................8F-42
STARTER MOTOR RELAY - OPERATION . . . 8F-41
STARTER MOTOR RELAY - REMOVAL.....8F-42
STARTER RELAY - DIAGNOSIS AND
TESTING...........................8F-41
STARTING - DESCRIPTION.............8F-31
STARTING - OPERATION...............8F-31
STARTING - STANDARD PROCEDURE,
JUMP................................0-7
STARTING SYSTEM - DIAGNOSIS AND
TESTING...........................8F-32
STARTING SYSTEM - SPECIFICATIONS,
TORQUE............................8F-37
STARTING SYSTEM, SPECIFICATIONS.....8F-36
STATE DISPLAY TEST MODE -
DESCRIPTION........................25-1
STATIONARY GLASS - DESCRIPTION
....23-145
STATIONARY GLASS - OPERATION
......23-145
STEERING - DESCRIPTION
..............19-1
STEERING - OPERATION
................19-1
STEERING COLUMN OPENING COVER -
INSTALLATION
......................23-114STEERING COLUMN OPENING COVER -
REMOVAL.........................23-113
STEERING FLOW AND PRESSURE -
DIAGNOSIS AND TESTING, POWER.......19-4
STEERING GEAR HOUSING PLUG -
INSTALLATION.......................19-30
STEERING GEAR HOUSING PLUG -
REMOVAL..........................19-29
STEERING GEAR LEAKAGE - DIAGNOSIS
AND TESTING, POWER................19-16
STEERING GEAR, SPECIAL TOOLS -
POWER............................19-22
STEERING GEAR, SPECIFICATIONS -
POWER............................19-21
STEERING LINKAGE, SPECIAL TOOLS....19-41,
19-44
STEERING PUMP - INITIAL OPERATION -
STANDARD PROCEDURE, POWER.......19-33
STEERING PUMP, SPECIAL TOOLS -
POWER............................19-38
STEERING SYSTEM - DIAGNOSIS AND
TESTING, POWER.....................19-2
STEERING SYSTEM - STANDARD
PROCEDURE, FLUSHING POWER........19-34
STEERING WHEEL - INSTALLATION......19-15
STEERING WHEEL - REMOVAL..........19-15
STEM SEAL - INSTALLATION, VALVE......9-83
STEM SEALS - REMOVAL, VALVE.........9-82
STOP LAMP - INSTALLATION, CENTER
HIGH MOUNTED......................8L-6
STOP LAMP - REMOVAL, CENTER HIGH
MOUNTED...........................8L-6
STOP LAMP UNIT - INSTALLATION,
CENTER HIGH MOUNTED...............8L-6
STOP LAMP UNIT - REMOVAL, CENTER
HIGH MOUNTED......................8L-6
STORAGE BIN - INSTALLATION.........23-114
STORAGE BIN - REMOVAL............23-114
STOWAGE TRAY - INSTALLATION, REAR
FLOOR............................23-121
STOWAGE TRAY - REMOVAL, REAR
FLOOR............................23-121
STRAP - INSTALLATION, CAB-TO-BED
GROUND...........................8A-14
STRAP - INSTALLATION, ENGINE-TO-
BODY GROUND......................8A-13
STRAP - INSTALLATION, HEATER CORE
GROUND...........................8A-14
STRAP - REMOVAL, CAB-TO-BED
GROUND...........................8A-13
STRAP - REMOVAL, ENGINE-TO-BODY
GROUND...........................8A-12
STRAP - REMOVAL, HEATER CORE
GROUND...........................8A-14
STRETCH - INSPECTION, MEASURING
TIMING CHAIN..................9-111,9-54
STRIKER - INSTALLATION, GLOVE BOX
LATCH ............................23-112
STRIKER - INSTALLATION, LATCH . 23-103,23-66,
23-73
STRIKER - LOWER - INSTALLATION,
LATCH .............................23-82
STRIKER - LOWER - REMOVAL, LATCH . . . 23-82
STRIKER - REMOVAL, GLOVE BOX
LATCH ............................23-111
STRIKER - REMOVAL, LATCH....23-103,23-66,
23-73
STRIKER - UPPER - INSTALLATION,
LATCH .............................23-82
STRIKER - UPPER - REMOVAL, LATCH . . . 23-82
STRIPE - INSTALLATION, TAPE..........23-89
STRIPE - REMOVAL, TAPE.............23-88
STRIPES AND DECALS - INSTALLATION,
BODY..............................23-87
STRIPES AND DECALS - REMOVAL,
BODY..............................23-87
STRUCTURAL ADHESIVE LOCATIONS,
SPECIFICATIONS.....................23-44
STUDS - INSTALLATION...............22-12
STUDS - REMOVAL...................22-12
SUCTION AND DISCHARGE LINE -
INSTALLATION.......................24-52
SUCTION AND DISCHARGE LINE -
REMOVAL
..........................24-51
SUN VISOR - INSTALLATION
..........23-127
SUN VISOR - REMOVAL
..............23-127
SUPPLIES - DESCRIPTION, 5 VOLT
......8E-17
SUPPLIES - OPERATION, 5 VOLT
........8E-19
BR/BEINDEX 29
Description Group-Page Description Group-Page Description Group-Page