transmission DODGE SPRINTER 2005 1.G User Guide

192 STARTING AND OPERATINGEMISSIONS CONTROL SYSTEM (CATALYTIC
CONVERTER)
INHALATION OF EXHAUST GAS FORDING (WADING CAPABILITY)
Avoid fording flooded roads or passing through water
unless you are certain as to how deep it is. Driving
through deep water can cause damage to the vehicle,
including but not limited to the electrical components,
engine, transmission, etc. This type of damage is not
covered under the Warranty.
WARNING!
When driving or parking the vehicle, make sure
that its exhaust system does not come into contact
with flammable material (such as dry leaves) as
these materials may otherwise catch fire.
WARNING!
Inhalation of exhaust gas is hazardous to your
health. All exhaust gas contains carbon monoxide
and inhaling it can cause unconsciousness and
lead to death.
Do not run the engine in confined areas (such as a
garage) which are not properly ventilated. If you
think that exhaust gas fumes are entering the
vehicle while driving, have the cause determined
and corrected immediately. If you must drive
under these conditions, drive only with at least
one window fully open.

WHAT TO DO IN EMERGENCIES
6
CONTENTS

Hazard Warning Flasher Switch . . . . . . . . . . . . . 196


Fire Extinguisher (Optional) . . . . . . . . . . . . . . . . . 197


Vehicle Tool Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . 197


Changing the Tire . . . . . . . . . . . . . . . . . . . . . . . . . . 198
Spare Wheel Location . . . . . . . . . . . . . . . . . . . . 200


Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
Using the Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . 203


Removing a Wheel . . . . . . . . . . . . . . . . . . . . . . . . . 206


Installing a Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . 206


Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209


Towing the Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 211
If the Engine is Damaged . . . . . . . . . . . . . . . . . 212
If the Transmission is Damaged . . . . . . . . . . . . 212
If the Front Axle is Damaged . . . . . . . . . . . . . . 212
If the Rear Axle is Damaged . . . . . . . . . . . . . . . 212

WHAT TO DO IN EMERGENCIES 199
6
Procedure:
1. Park the vehicle on a firm, level, non-slippery surface.
2. Switch on the hazard warning flasher switch, apply the parking brake, and place the transmission
selector in "P".
3. Everyone must leave the vehicle before you jack it up.
4. Everyone must leave the danger zone, before jacking the vehicle. 5. The vehicle must be safeguarded in accordance
with legal regulations (such as using a warning
triangle).
6. Prevent vehicle from rolling away by blocking wheels with wheel chocks (not supplied with
vehicle) or sizable wood block or stone.
On a level road, place one chock in front of and one
behind the wheel that is diagonally opposite to the
wheel being changed.
When changing a wheel on mild uphill or downhill
grades, place chocks on the downhill side blocking
both wheels of the other axle.
Do not jack the vehicle up more than 1.2 in (30
mm) between the tire and the surface. Otherwise,
the vehicle may tip over and may cause serious
injury or death to you or others.
Precautions when changing a wheel:
For the torque, refer to
"Installing a wheel ";
Do not damage, grease or oil wheel bolts or their
threads.
WARNING!
Do not change wheels on either steep uphill or
downhill grades. The vehicle may begin to move
and fall from the jack which could cause personal
injury and property damage.

212 WHAT TO DO IN EMERGENCIESIf the Engine is DamagedFor towing distances up to 30 miles (about 50 km)
 Shift gear selector lever to "N" position.
 Do not exceed a towing speed of 30 mph (50 km / h).
For towing distances greater than 30 miles (about
50 km)
 Remove the propeller shafts leading to the drive axles.
The vehicle can be towed without restriction.If the Transmission is Damaged Remove the propeller shafts leading to the drive
axles.
If the Front Axle is Damaged Raise the front axle.
 Observe the same towing restrictions as for engine damage.IftheRearAxleisDamagedRaise the rear axle.
NOTE: Comply with local legal regulations regarding
towing vehicles.

258 MAINTAINING YOUR VEHICLERecommended Fluids and LubricantsThe manufacturer recommends for your vehicle model
the use of DaimlerChrysler approved fluids and
lubricants, e.g. engine oil, gear oil, automatic
transmission fluid, brake fluid, power steering fluid,
coolant and anti-corrosion/anti-freeze fluid only.
WARNING!
Failure to use fluids and lubricants which meet
the standards and specifications described in this
booklet or failure to adhere to the specified re-
placement intervals may result in damage to safe-
ty-related systems of your vehicle, such as the
brake system, which could cause an accident and/
or serious injury to you and others.
Use only fluids and lubricants meeting the
standards and specifications and adhere to
specified replacement intervals.
CAUTION!
Failure to use fluids and lubricants which meet
the standards and specifications described in this
booklet or failure to adhere to the specified
replacement intervals may result in a significantly
shortened service life and/or damage to
components of your vehicle, the repair of which
will not be covered by Warranty.
Use only fluids and lubricants meeting the
standards and specifications and adhere to
specified replacement intervals.

MAINTAINING YOUR VEHICLE 261
7
COMPONENT SERVICE INTERVAL PRODUCT NAME/PRODUCT NUMBER MB
SHEET
Air Conditioning
The air conditioning system of your vehicle contains R-134a, a refrigerant that does not deplete the ozone layer in the
upper atmosphere.
Refrigerant R-134a — Refrigerant R-134a 361.0 Automatic
Transmission Fluid once only at
80,000 mi
(128,000 km) Shell ATF 3403/M-115
MOPAR® Part No. 05127382AA, or equivalent
Fuchs/Shell ATF 3353 236.10
236.12
Brakes
Use brake fluid approved to DaimlerChr ysler standard MB 331.0 and/or DaimlerChrysler material standard MS-9971,
brake fluid certified to DOT 4 Plus standards, that also ma intains a minimum dry boiling point (ERBP) of 500°F (260°C),
a minimum wet boiling point (WERBP) of 356°F (180°C) and maximum viscosity of 1500 mm
2/s, conforming to FMVSS
116 and ISO 4925.
Brake Fluid 2 years Intac B026D Dry boiling point: 500°F (260°C )
Wet boiling point: 356°F (180°C),
MOPAR® MS-9971 Part No. 04549625AC, or equivalent 331.0
Engine Oil 12 months or 10,000 mi
(16,000 km) See "Approved Engine Oils"

266 MAINTENANCE SCHEDULES
M A I
N T
E
N A
N
C E
S
C
H
E
D
U L
E
S8
MAINTENANCE - WITH ASSYST MAINTENANCE
COMPUTERASSYST provides you with information on the best
possible timing for maintenance work.
When the next maintenance service is due, this will be
indicated in the multi-function display with the
symbol
9 Oil service and fuel filter replacement
9 Maintenance service - displayed in km/miles
or days.
9
If the display shows the number of days, the symbol
È will also appear in the multi-function display.
You should have the maintenance performed within
the stated period/distance.
The service indicator will be reset by your Sprinter
Dealer after an oil service and/or maintenance service
has been performed.
REGULAR CHECK-UPSTo maintain the safe operation of your vehicle, it is
recommended that you perform the following tasks on
a regular basis (i.e., weekly or whenever the vehicle is
refueled). Check:
 Engine oil level
 Brake system, clutch mechanism – fluid level
 Battery – acid level
 Windshield washer system and headlamp cleaning
system – fluid level
 Mechanical assemblies (e. g. ,engine, transmission, etc.) – check for leaks
 Condition of tires and tire pressures
 All exterior lights

268 MAINTENANCE SCHEDULES
M A I
N T
E
N A
N
C E
S
C
H
E
D
U L
E
S8
SCOPE OF WORK FOR MAINTENANCE SERVICE
Oil ServiceOil change
Engine:
Oil change and filter replacement
Check fluid levels of the following system, refill as
necessary.
If fluid is lost, trace and eliminate cause – as a separate
order.
Power-assisted steering
Lubrication work:
Trailer tow hitch (original equipment)
Maintenance
ASSYST maintenance computer reset Function check
Signalling system,
warning and indicator lamps
Headlamps, exterior lighting
Windscreen wipers,
windscreen washer system
Check for leaks and damage.
Check for abrasion points and ensure that
lines are correctly routed!
All assemblies:
Engine, transmission, transfer case, front axle, rear
axle, steering, power steering pump
All lines and hoses, sensor cables
Rubber boots on front axle drive shafts,
rubber boots on front axle suspension ball joints, shock
absorbers

270 MAINTENANCE SCHEDULES
M A I
N T
E
N A
N
C E
S
C
H
E
D
U L
E
S8
Additional Maintenance WorkAutomatic transmission once only at 80,000 miles/
128000km
Oil and filter change
During every second maintenance service
Air cleaner without maintenance indicator:
Air cleaner filter element renewal
Check poly-V-belt for wear and signs of damage
During every sixth maintenance service
Rear axle
Additional Maintenance Work After ... YearsEvery 2 years
Change brake fluid
Every 3 years
Air cleaner filter element renewal
(note installation date
)
Every 15 years or 100,000 miles
Coolant renewal
Note coolant composition

278 INDEXASSYST Maintenance Computer . . . . . . . . . . . . . . . 110
Automatic Lock Feature . . . . . . . . . . . . . . . . . . . . . . . . 19
Automatic Transmission . . . . . . . . . . . . . . . . . . . . . . 145Accelerator Position . . . . . . . . . . . . . . . . . . . . . . . . 146
Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Gear Selector Lever Position . . . . . . . . . . . . . . . . . 147
Maneuvering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Selector Lever Manually Unlocking. . . . . . . . . . . 150
Stopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Auxiliary Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Auxiliary Heat Exchanger . . . . . . . . . . . . . . . . . . . . . 137
Auxiliary Heater Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Timer Auxiliary Heater (Water and Air Heater) 132
Tips for Coping with Problems . . . . . . . . . . . . . . 138BBatteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . 228
Disconnecting the Battery . . . . . . . . . . . . . . . . . . . 227
Reconnecting the Battery . . . . . . . . . . . . . . . . . . . . 228
Replacing Batteries in Remote Keyless Entry . . . . 22
Battery Charge Indicator Lamp . . . . . . . . . . . . . . . . . 104 Belt Tensioners
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Belt Tensioners and Airbag . . . . . . . . . . . . . . . . . . . . . 49
Bleeding the Diesel Fuel System . . . . . . . . . . . . . . . . 185
Body Builder Guideline . . . . . . . . . . . . . . . . . . . . . . . 193
Brake Assist System (BAS) . . . . . . . . . . . . . . . . . . . . . 169
Brake fluid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
Brake Fluid Reservoir . . . . . . . . . . . . . . . . . . . . . . . . . 222
Brake Indicator Lamp . . . . . . . . . . . . . . . . . . . . . . . . . 157
Brake Pad Wear Indicator. . . . . . . . . . . . . . . . . . . . . . 156
Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 Fluid Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
Brake System, Anti-Lock . . . . . . . . . . . . . . . . . . . . . . 162
Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 Brake Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
Service Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Bulbs Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . 245
Front Lamp Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
CCapacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
Care of Vehicle