clock DODGE SPRINTER 2008 2.G User Guide

234 Controls in detailAir conditioning
3
\1To increase:
turn the temperature
selector control clockwise.
\1To reduce:
turn the temperature se-
lector control counterclockwise.
The fuel-fired heater booster system
heats the vehicle interior as quickly as
possible while the engine is running.The switch for the heater booster func-
tion is between the light switch and the
steering wheel.
Vehicles with auxiliary heatingVehicles without auxiliary heating*
1To switch the auxiliary heating on / off
(\2page 238)
2To switch the heater booster function
on / off
Heater booster function* iThe auxiliary heating automatically
switches to heater booster mode af-
ter the engine is started.
N54.25-2926-31
N54.25-2927-31
nf_BA.book Page 234 Friday, January 25, 2008 3:53 PM

240 Controls in detailAuxiliary heating/ventilation*
3
\1To switch the auxiliary heating on:

press button
2
.
Indicator lamp1
lights up briefly.
\1To switch the auxiliary heating
off:
press button
3
.
Indicator lamp
1
lights up briefly.
The auxiliary heating operates for
around a further 2 minutes and then
switches off automatically.
Synchronizing the remote control
\1
Press and hold the
ö
switch for
more than 10 seconds:
The red indicator lamp in the
ö

switch remains lit until it is released.
Afterward, the red indicator lamp in
the
ö
switch flashes. The system
is activated for synchronizing.
\1
Press button
2
on the remote con-
trol.
The indicator lamp in the
ö

switch stops flashing and goes out.
The remote control and the control
panel are synchronized.
Selecting a switch-on timeYou can use the operating system to de-
fine up to 3 switch-on times, one of
which can be selected to switch on the
auxiliary heating / ventilation.
iChange the batteries immediately if
indicator lamp
1
does not
light up
briefly each time a button is pressed
(
\2
page 541).
iIf you press button
3
on the remote
control during the first 3 seconds of
synchronization process, only this re-
mote control will be synchronized
with the clock.
Any other remote control units that
were synchronized will be cleared.
nf_BA.book Page 240 Friday, January 25, 2008 3:53 PM

317 Operation
Refueling
4
\1
Remove the key from the ignition
lock.
\1
Switch off the auxiliary heating.
\1
Open the driver’s door.
\1
Open the fuel filler flap.
\1
Close all the vehicle’s doors, so that
no fuel vapors can enter the vehicle.
\1
Turn fuel filler cap
2
counterclock-
wise and let it hang by retaining
strap
1
.
\1
Only fill the tank until the pump noz-
zle switches off.
\1
Replace fuel filler cap
2
and turn it
clockwise.A clicking sound indicates that the
fuel filler cap is fully closed.
\1
Open the driver’s door and close the
fuel filler flap.
You will find information about fuel in
the “Technical data” section
(
\2
page 610).
nf_BA.book Page 317 Friday, January 25, 2008 3:53 PM

330 OperationEngine compartment
4
\1
Slowly unscrew cap
1
counter-
clockwise to reduce excess pres-
sure.
\1
Continue turning the cap and remove
it.
\1
Add coolant as far as the MAX mark.
\1
Twist cap
1
back on.
For coolant specifications, see "Service
products and capacities" (
\2
page 604).
Warning
G
When opening the coolant expansion tank
there is a risk of scalding from hot coolant
spraying out. The cooling system and the
coolant expansion tank are pressurized
when the engine is at normal operating
temperature.
Wear gloves and eye protection. Only
open the coolant expansion tank when
the coolant temperature is less than
122 °F (50 °C).
Warning
G
Coolant contains glycol and is therefore
toxic. Do not swallow coolant. Consult a
doctor immediately if any coolant is swal-
lowed.
Do not allow coolant to come into contact
with your skin, eyes or clothing. In the
event of contact with the eyes, rinse them
thoroughly with clean water. Clean skin
and clothes immediately with soap and
water. Change out of soiled clothing with-
out delay.
!
CAUTION
Check the cooling and heating sys-
tems regularly for leaks. If a large
quantity of coolant is lost, have the
cause traced and rectified at an au-
thorized Sprinter Dealer.
nf_BA.book Page 330 Friday, January 25, 2008 3:53 PM

513 Practical hints
Where will I find...?
5
The warning triangles are behind the
driver's seat.1Warning triangles\1
Remove warning triangles
1
from
the brackets upward.The road hazard lamp is located in the
storage compartment in the driver’s
door.
1Locked
2Unlocked
\1
Turn the two quick-release locks
counter-clockwise to unlock
2
and
fold out the cover
3Road hazard lamp
Warning triangle*
N72.10-2148-31
Road hazard lamp*
iCheck the function of the road haz-
ard lamp regularly, and replace the
batteries or the bulb if necessary.
nf_BA.book Page 513 Friday, January 25, 2008 3:53 PM

514 Practical hintsWhere will I find...?
5
The fire extinguisher is secured to the
front of the passenger’s seat base. 1Fire extinguisher
2Tabs
\1
Pull tabs
2
upward.
\1
Take fire extinguisher
1
out of the
bracket.The first-aid kit is located in the storage
compartment in the passenger’s door.
1Locked
2UnlockedTurn the two quick-release locks clock-
wise to unlock
2
and fold out the cover.
Fire extinguisher*
iRead the instructions on the fire ex-
tinguisher carefully and familiarize
yourself with its operation.
First-aid kit*
nf_BA.book Page 514 Friday, January 25, 2008 3:53 PM

516 Practical hintsWhere will I find...?
5
1Quick-release lock
2Unlocked\1To unlock:
turn quick-release lock
1
counterclockwise or clockwise.
\1
Remove the cover.
\1To lock:
press quick-release lock
1

down until it engages.
3Tensioning lever
4Jack
5Vehicle tool kit\1
Remove the vehicle tool kit.
\1
Pull tensioning lever
3
upward and
unhook the retaining strap of
jack
4
.
Warning (Continued)
G
Do not crawl under the vehicle if it is only
supported by the jack.Make sure that no persons are present in
the vehicle when raising the vehicle.Do not start the engine while the vehicle
is raised.Make sure that the distance between the
underside of the tires and the ground
does not exceed 30 mm.If work is to be carried out under the
vehicle, the vehicle must be placed on
stands.
nf_BA.book Page 516 Friday, January 25, 2008 3:53 PM

518 Practical hintsWhere will I find...?
5
\1
Open the rear doors (
\2
page 100).
\1
Insert a screwdriver into
recesses
2
and pry off covers
1
.
\1
Using the wheel wrench from the ve-
hicle tool kit (
\2
page 515), now un-
screw the visible bolts approximately
20 turns counterclockwise.
3Securing hook
4Sleeve
5Spare wheel bracket\1
Raise spare wheel bracket
5
slight-
ly and release left securing hook
3
.
\1
Slide the pump lever for the jack into
sleeve
4
on spare wheel
bracket5
.
\1
Raise spare wheel bracket
5
using
the pump lever and release right se-
curing hook
3
.
\1
Slowly lower spare wheel bracket
5

to the ground.
\1
Raise spare wheel bracket
5
slight-
ly and pull the pump lever out of
sleeve
4
.
nf_BA.book Page 518 Friday, January 25, 2008 3:53 PM

529 Practical hints
Changing bulbs
5
\1
Turn bulb holder
1
and the bulb
counterclockwise and remove the
holder.
\1
Press down on the bulb, turn it coun-
terclockwise and remove it from bulb
holder
1
.
\1
Press the new bulb into bulb
holder
1
and screw it in clockwise.
\1
Place bulb holder
1
into the lamp
and turn it clockwise.
Parking lamps/side marker 1Cap\1
Turn cap
1
counterclockwise and
remove it.
\1
Remove the bulb holder together
with the bulb.
\1
Pull the bulb out of the bulb holder.
\1
Press the new bulb into the bulb
holder.
\1
Insert the bulb holder with bulb into
the reflector.
\1
Replace cap
1
and turn it clockwise
to the stop.
nf_BA.book Page 529 Friday, January 25, 2008 3:53 PM

532 Practical hintsChanging bulbs
5
2Retaining lugs
3Brake lamp
4Side marker, Standing lamp (Canada
only), tail lamp
5Reverse lamp
6Turn signal lamp
7Rear foglamp (driver’s side)\1
Release retaining lugs
2
and re-
move the bulb holder from the rear
lamp unit.
\1
Press down on the bulb, turn it coun-
terclockwise and remove it from the
holder.
\1
Press the new bulb into the bulb
holder and screw it in clockwise.
\1
Plug the connectors into the bulb
holder.
\1
Fit the rear lamp unit.
To do this, clip the bulb holder into
the three holes provided on the side
and tighten screws
1
.
nf_BA.book Page 532 Friday, January 25, 2008 3:53 PM