engine FIAT BRAVO 2007 2.G Manual PDF
[x] Cancel search | Manufacturer: FIAT, Model Year: 2007, Model line: BRAVO, Model: FIAT BRAVO 2007 2.GPages: 246, PDF Size: 3.75 MB
Page 201 of 246

200
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CAR
MAINTENANCE
WINDSCREEN/REAR
WINDOW/HEADLIGHT
WASHER FLUID fig. 11
To top up, open the cap Aand then pour
a mixture of water and TUTELA PRO-
FESSIONAL SC 35, in the following
concentrations:
❒30% TUTELA PROFESSIONAL
SC 35and 70% water in summer;
❒50% di TUTELA PROFESSIONAL
SC 35and 50% water in winter.
In case of temperatures below –20°C, use
undiluted TUTELA PROFESSIONAL
SC 35 fluid.
fig. 11F0Q0666mDo not travel with the wind-
screen washer reservoir emp-
ty. The windscreen washer is funda-
mental for improving visibility.
WARNING
Certain commercial addi-
tives for windscreen washers
are inflammable. The engine com-
partment contains hot components
which may set it on fire.
WARNING
BRAKE FLUID fig. 12
Unscrew cap Aand check that the fluid
level in the reservoir is at maximum.
Fluid level in the reservoir shall not exceed
the MAXmark.
If fluid has to be added, it is suggested to
use the brake fluid in table “Fluids and lu-
bricants” (see chapter “Technical specifi-
cations”). When opening cap Atake the
utmost care to prevent impurities enter-
ing the tank.
For topping up, always use a funnel with
integrated filter with mesh equal to or
lower than 0.12 mm.
fig. 12F0Q0664m
Check level through the reservoir.
For versions fitted with headlight wash-
er, remove the filter and the relevant dip-
stick. Use the dipstick to check the fluid
level inside the reservoir.
191-212 BRAVO GB 10-05-2007 9:21 Pagina 200
Page 204 of 246

203
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CAR
MAINTENANCE
USEFUL ADVICE
FOR LENGTHENING THE LIFE
OF YOUR BATTERY
To avoid draining your battery and length-
en its life, observe the following indica-
tions:
❒ when you park the car, ensure the
doors, tailgate and bonnet are closed
properly;
❒ the ceiling lights must be off. The car
is however provided with an automat-
ic system for switching off internal
lights;
❒ do not keep accessories (e.g.: sound
system, hazard lights, etc.) switched on
for a long time when the engine is not
running;
❒ before performing any operation on the
electrical system, disconnect the bat-
tery negative cable;
❒ battery terminals shall always be per-
fectly tightened.Moreover, this might lead to a higher risk
of the battery electrolyte freezing (this
may even occur at -10°C). If the car is in-
active for a long period of time, refer to
“Car inactivity”, in section “Correct use
of the car”.
If after buying the car, you want to install
electric accessories which require per-
manent electric supply (alarm, etc.) con-
tact Fiat Dealership whose qualified per-
sonnel, in addition to suggesting the most
suitable devices, will evaluate the overall
electric absorption, checking whether the
car’s electric system is capable of with-
standing the load required, or whether it
should be integrated with a more power-
ful battery. In fact, since these devices continue ab-
sorbing energy even when the ignition key
is off, they gradually run down the battery.
191-212 BRAVO GB 10-05-2007 9:21 Pagina 203
Page 209 of 246

208
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CAR
MAINTENANCE
BODYWORK
PROTECTION FROM
ATMOSPHERIC AGENTS
The main causes of corrosion are the fol-
lowing:
❒ atmospheric pollution;
❒ salty air and humidity (coastal areas, or
hot humid climates);
❒ seasonal environment conditions.
Not to be underestimated is also the abra-
sive action of wind-borne atmospheric
dust and sand and mud and gravel raised
by other cars.
On your Fiat Bravo, Fiat implemented the
best manufacturing technologies to effec-
tively protect the bodywork against cor-
rosion.These include:
❒ Painting products and systems which
give the car particular resistance to cor-
rosion and abrasion;
❒ Use of galvanised (or pretreated) steel
sheets, with high resistance to corro-
sion;
❒ Spraying the underbody, engine com-
partment, wheelhouse internal parts
and other parts with highly protective
wax products;
❒ Spraying of plastic parts, with a pro-
tective function, in the more exposed
points: underdoor, inner fender parts,
edges, etc.;
❒Use of “open” boxed sections to pre-
vent condensation and pockets of mois-
ture from triggering rust inside.BODY AND UNDERBODY
WARRANTY
Your car is covered by warranty against
perforation due to rust of any original el-
ement of the structure or body. For the
general terms of this warranty, refer to
the Fiat Warranty booklet.
191-212 BRAVO GB 10-05-2007 9:21 Pagina 208
Page 211 of 246

210
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CAR
MAINTENANCE
Front headlights
IMPORTANT Never use aromatic sub-
stances (e.g.: petrol) or ketones (e.g.: ace-
tone) for cleaning front headlight plastic
lens.
Windows
Use specific window cleaner product. Use
also clean cloths to avoid scratching the
glass or damaging the transparency.
IMPORTANT The inside of the rearscreen
should be wiped gently with a cloth in the
direction of the filaments to avoid damag-
ing the heating device.Engine compartment
At the end of the winter the engine com-
partment should be carefully washed,
without directing the jet against electron-
ic control units. Contact a specialised
workshop to have this done.
IMPORTANT The car should be washed
with the engine cold and the ignition key
at STOP. After washing make sure that
the various protections (e.g. rubber caps
and various covers) have not been dam-
aged or removed.INTERIORS
Periodically check that water is not trapped
under the mats (due to water dripping off
shoes, umbrellas, etc.) which could cause
oxidisation of the sheet metal.
CLEANING SEATS AND FABRIC
AND VELVET PARTS
Use a soft brush or vacuum cleaner to re-
move dust. Velvet is cleaned better if the
brush is moistened.
Rub the seats with a sponge moistened
with a solution of water and neutral de-
tergent.
191-212 BRAVO GB 10-05-2007 9:21 Pagina 210
Page 214 of 246

213
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
INDEX
TECHNICAL
SPECIFICATIONS
IDENTIFICATION DATA ................................................... 214
ENGINE CODES - BODYWORK VERSIONS .............. 216
ENGINE .................................................................................... 217
FUEL FEED/IGNITION ........................................................ 218
TRANSMISSION .................................................................... 218
BRAKES ..................................................................................... 219
SUSPENSIONS......................................................................... 219
STEERING ................................................................................. 219
WHEELS .................................................................................... 220
DIMENSIONS .......................................................................... 224
PERFORMANCE ..................................................................... 225
WEIGHTS ................................................................................. 226
CAPACITIES ........................................................................... 227
FLUIDS AND LUBRICANTS ............................................... 228
FUEL CONSUMPTION ........................................................ 230
CO
2EMISSIONS .................................................................... 231
RADIO FREQUENCY REMOTE CONTROL:
MINISTERIAL HOMOLOGATION .................................. 232
T T
E E
C C
H H
N N
I I
C C
A A
L L
S S
P P
E E
C C
I I
F F
I I
C C
A A
T T
I I
O O
N N
S S
213-236 BRAVO GB 16-05-2007 10:11 Pagina 213
Page 215 of 246

MODEL PLATE fig. 2
The plate is to be found on the front cross-
member of the engine compartment and
bears the following identification data:
BHomologation number.
CVehicle type code.
DChassis number.
EMaximum vehicle weight fully loaded.
FMaximum vehicle weight fully loaded
with trailer.GMaximum vehicle weight on front axle.
HMaximum vehicle weight on rear axle.
IEngine type.
LBody version code.
MSpare part code.
NSmoke opacity index (for diesel en-
gines).
IDENTIFICATION DATA
You are advised to note the identification
codes. The identification data stamped and
given on the plates and their position are
the following fig. 1:
❒ Model plate
❒Chassis marking
❒ Bodywork paint identification plate
❒Engine marking.
214
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
INDEX
TECHNICAL
SPECIFICATIONSDASHBOARD
AND CONTROLS
fig. 1F0Q0736mfig. 2F0Q0029m
213-236 BRAVO GB 16-05-2007 10:11 Pagina 214
Page 216 of 246

BODYWORK PAINT
IDENTIFICATION PLATE fig. 4
The plate is applied inside the bonnet and
it bears the following data:
A- Paint manufacturer.
B- Colour name.
C- Fiat colour code.
D- Respray and touch up code.ENGINE MARKING
Engine marking is stamped on the cylinder
block and includes the model and the
chassis number.
CHASSIS MARKING
It is printed on the passenger compart-
ment floor, near the right-hand front seat.
It can be reached by sliding forth the lid
A-fig. 3.
It bears the following data:
❒car model (ZFA 198000);
❒ chassis number.
215
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
INDEX
TECHNICAL
SPECIFICATIONS
fig. 4F0Q0100mfig. 3F0Q0667m
213-236 BRAVO GB 16-05-2007 10:11 Pagina 215
Page 217 of 246

216
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
INDEX
TECHNICAL
SPECIFICATIONSDASHBOARD
AND CONTROLS
ENGINE CODES - BODYWORK VERSIONS
Engine code Bodywork version
1.4
16V192B2000 198AXA1B 00
1.4 T-JET 150 HP198A1000 198AXF1B 05
198AXF1B 05B (▲)
1.9 Multijet 8V192A8000 198AXB1A 01 ()
198AXB1A 01C ()
198AXB1A 01B () (▲)
198AXB1A 01D () (▲)
1.9 Multijet 16V937A5000 198AXC1B 02 ()
198AXC1B 02C ()
198AXC1B 02B () (▲)
198AXC1B 02D () (▲)
1.9 Multijet
8V () 192B4000 198AXD1A 03 ()
198AXD1A 03C ()
198AXD1A 03B () (▲)
198AXD1A 03D () (▲)
1.9 Multijet
8V () 192B5000 198AXE1A 04
198AXE1A 04C ()
198AXE1A 04B () (▲)
() Versions with DPF
() Versions without DPF
(▲) Versions with option of 18” tyres
() Versions for specific markets
213-236 BRAVO GB 16-05-2007 10:11 Pagina 216
Page 218 of 246

1.9
Multijet 8V
192A8000
Diesel
4 in line
82.0 x 90.4
1910
18
88
120
4000
255
26
2000
–
Diesel fuel for
motor vehicles
(Specification
EN590)
217
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
INDEX
TECHNICAL
SPECIFICATIONS
1.4 16V
192B2000
Otto
4 in line
72.0 x 84.0
1368
11
66
90
5500
128
13
4500
NGK
DCPR7E-N-10
Unleaded
petrol
95 RON
(Specification
EN228)
1.9
Multijet 16V
937A5000
Diesel
4 in line
82.0 x 90.4
1910
17.5
110
150
4000
305
31
2000
–
Diesel fuel for
motor vehicles
(Specification
EN590)
1.9
Multijet 8V (●)
192B5000
Diesel
4 in line
82.0 x 90.4
1910
18
66
90
4000
255
26
2000
–
Diesel fuel for
motor vehicles
(Specification
EN590)
1.9
Multijet 8V (●)
192B4000
Diesel
4 in line
82.0 x 90.4
1910
18
85
115
4000
255
26
2000
–
Diesel fuel for
motor vehicles
(Specification
EN590)
1.4 T-JET
150 HP
198A1000
Otto
4
in line
72.0 x 84.0
1368
9.8
110
150
5500
206
21
2250
NGK
IKR9F8
Unleaded
petrol
95 RON
(Specification
EN228)
ENGINE
GENERAL
Engine code
Cycle
Number and layout of cylinders
Piston bore and stroke mm
Total displacement cm3
Compression ratio
Maximum power (EEC) kW
HP
corresponding ratio rpm
Maximum torque (EEC) Nm
kgm
corresponding ratio rpm
Spark plugs
Fuel
(●)Versions for specific markets
213-236 BRAVO GB 16-05-2007 10:11 Pagina 217
Page 228 of 246

CAPACITIES
1.4 16V - 1.4 T-JET 150 HP
227
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
INDEX
TECHNICAL
SPECIFICATIONS
1.9 Multijet
Fuel tank:
including a reserve of:
Engine cooling system– with climate control:
Engine sump:
Engine sump and filter:
Gearbox/differential casing:
Hydraulic brake circuitwith ABS:
Windscreen /
rear window / headlight
washer fluid reservoir: (*)
(*) The values in brackets refer to versions with headlight washers.
(
❏) Version 1.9 Multijet 8v
(
) Version 1.9 Multijet 16v
(
❍) Version 1.4 T-JET 150 HP
(▲) For particularly hard climate conditions, we recommend use of a 60% PARAFLUUPand 40% demineralized water mixture.
litres
57 ()
8-10 ()
–
4.4 ()
4.7 ()
1.76 (
❏)
1.87 ()
–
3 (6)kg
–
–
7.0
3.8 ()
4.0 ()
1.6 (❏)
1.7 ()
0.525
– kg
–
–
5.2
2.4
2.55
1.7
2.0 (❍)
0.525
–Recommended fuels and
genuine lubricants
Unleaded petrol
with no less than 95 R.O.N
(Specification EN228)
() Diesel fuel for motor vehicles
(Specification EN590)
Mixture of 50% demineralised water
and 50% PARAFLU
UP(▲)
SELENIA K P.E.
() SELENIA WR
TUTELA CAR TECHNYX
TUTELA CAR MATRYX (
❍)
TUTELA TOP 4
Mixture of water and
TUTELA
PROFESSIONAL SC 35 litres
57
8-10
–
2.75
2.9
1.87
2.4 (❍)
–
3 (6)
213-236 BRAVO GB 16-05-2007 10:11 Pagina 227