Load FIAT DOBLO 2007 1.G User Guide

84GETTING TO KNOW YOUR VEHICLE
fig. 131
F0A0420b
fig. 130
F0A0412b
– tilt the central seat back pulling
band A-fig. 129upwards;
– pull the bands B-fig. 130and tilt
the seat completely;
– secure tilted seats by the proper
belts C-fig. 131(one per seat) to the
front headrests.
IMPORTANTDo not travel with
second row seats tipped and third row
seats set in normal position of use, a
buzzer will sound to indicate the
wrong seat position.ANCHORING THE LOAD
A boot mat is provided (optional for
Fiat Doblò Cargo base versions). To
fasten the load, fastening hooks are
provided (quantity varying according
to versions) fig. 132secured to the
floor and that can be accessed direct-
ly also if the mat is fitted.
fig. 132
F0A0195b
To re-position the seats, release the
belts C-fig. 131, tilt the side seats and
the central seat cushion then pull band
A-fig. 129to tilt the seat back and an-
chor it to the proper brackets.
It is absolutely forbidden
to travel with the second
row seats tipped and pas-
sengers seated on the third row
seats (as specified on the seat la-
bel).

86GETTING TO KNOW YOUR VEHICLE
After travelling a few
kilometres, check that
the attachment fastening
screws are tight.
Distribute the load even-
ly and when driving, bear
in mind the increased
sensitivity of the vehicle to side
wind.
Never exceed the max.
permissible loads (see
section “Technical speci-
fications”).
Strictly comply with cur-
rent law regulations con-
cerning max. overall di-
mensions.
fig. 136
F0A0185b
ROOF RACK/SKI
RACK
PRESETTING
To use the roof racks you shall re-
move the caps set in points fig. 136.
Attach the roof rack bar brackets to
the fasteners.
IMPORTANTAlways follow the
instructions provided with the kit
carefully. The bars should be fitted by
skilled personnel.
For safety reasons the
bonnet must be closed
properly to avoid its
opening while the vehicle is trav-
elling. Therefore, always check it
is properly closed and the catch
engaged. Should you notice that
the catch is not perfectly engaged
when travelling, stop the vehicle
immediately and close the bon-
net. To close the bonnet
1)Hold the bonnet up with one hand
and, with the other, remove rod A-
fig. 135from recess Band replace it
in its clip.
2)Lower the bonnet until it is about
20 cm above the engine compartment,
and then let it drop, ensuring that it
is fully closed and not just held in po-
sition by the safety catch.
If the bonnet does not close properly
do not push it down but open it again
and repeat the above procedure.

87GETTING TO KNOW YOUR VEHICLE
LOADING RAMPS
Loading ramps are available at Lin-
eaccessori Fiat.
Never move the vehicle
with ramps extracted.
Before restarting the ve-
hicle always check that ramps are
properly secured into their hous-
ings.Loading with ramps
shall be only carried out
with the vehicle station-
ary and handbrake engaged.
fig. 137
F0A0221b
To use the rear ramp fig. 137,
strictly follow the instructions shown
on the plate applied on the left side
of the boot.IMPORTANTMax. rear ramp car-
rying capacity is 250 kg.

88GETTING TO KNOW YOUR VEHICLE
To use the side ramp, fig. 138,
open the side sliding door, take han-
dle Aand take out the ramp as shown
by the arrow until locking it.
IMPORTANTMax. side ramp car-
rying capacity is 60 kg.
When you have finished, take handle
Aand refit the side ramp into its hous-
ing making it sliding as shown by the
arrow fig. 138.
fig. 138
F0A0234b
HEADLIGHTS
ADJUSTING THE
HEADLIGHT BEAM
The correct positioning of the head-
light beams is very important for the
comfort and safety, not only of the
person driving the vehicle but also all
other road users.
This is also covered by a specific law.
To ensure you and other drivers
have the best visibility conditions when
travelling with the headlights on, the
headlights must be set properly.
Have the headlight positioning
checked at a Fiat Dealershipand ad-
justed if necessary.SLANT COMPENSATION
The vehicle is fitted with an electri-
cal device for correcting the headlight
slant. The device can be operated with
ignition key at MARand dipped
beams on.
When the vehicle is loaded, it
“slopes” backwards. This means that
the headlight beam rises. In this case,
it is necessary to return it to the cor-
rect position.
Proceed as follows:
– hold button B-fig. 139pressed to
increase by one position (e.g.: 0➟1,
1➟2, 2➟3);
– hold button Apressed to decrease
by one position (e.g.: 3➟2, 2➟1, 1➟0).
Display Cshows the positions dur-
ing the adjustment.
0y
1Δ
70
22: 1 10
7
7B
AC
fig. 139
F0A0085b

89GETTING TO KNOW YOUR VEHICLE
ABS
The vehicle can be fitted with an ABS
braking system, which prevents the
wheels from locking when braking,
makes the most of road grip and gives
the best control when emergency
braking under difficult road conditions.
The driver can tell the ABS system
has come into play because the brake
pedal pulsates slightly and the system
gets noisier.
This should not be interpreted as a
fault in the brakes; on the contrary it
is a sign that the ABS system is work-
ing: it tells the driver that the vehicle
is travelling at the limit of its road grip
and that he should alter his speed to
fit the type of road surface.
The ABS system is an addition to the
basic braking system. If there is a mal-
function, the system turns off auto-
matically and only the ordinary brakes
continue to work.If a failure occurs, and consequently
the anti-lock function is not effective,
the braking system will continue to
work as usual.
If you have never driven a vehicle
with ABS before, you should practice
using the system on slippery terrain,
obviously with the necessary safety
precautions and keeping to the High-
way Code of the country you are in.
It is also a good idea to read the fol-
lowing information carefully.
The advantage in using the ABS sys-
tem is that it continues to give you
maximum manoeuvrability even when
braking hard in conditions of poor grip
by preventing the wheels locking.
You should, however, not expect the
braking distance to always decrease:
for example surfaces with gravel or
fresh snow on a slippery road will in
fact increase the braking distance. Correct positions as a function
of the load
0- one or two occupants in the
front seats.
1- five occupants.
2- five occupants + load in boot.
3- driver + maximum permissible
load stowed in boot.
Check the headlight
beam position every time
you change the load to be
carried.
HEADLIGHT ADJUSTMENT
ABROAD
Headlights are orientated as to drive
inside the country of origin before sell-
ing the vehicle. When travelling in
countries with opposite driving direc-
tion, you need to cover the headlight
areas according to the Road Code of
the country you are travelling in.

96GETTING TO KNOW YOUR VEHICLE
The correct operation of
front airbags, side airbags
and pretensioners is en-
sured only if the vehicle is not
overloaded.
Do not wash the seat
back in vehicles with side
airbags with pressurised
steam or water in automatic seat
washing stations.
The airbag does not re-
place seat belts but rather
increases their effective-
ness. Furthermore, the airbag is
not fired in the event of low
speed front collisions, side colli-
sions, rear-end shunts and roll-
overs. In these cases, the passen-
gers are only protected by the
seat belts which for this reason
must always be fastened.
Always drive with both
hands on the rim of the
steering wheel so that the
airbag is free to inflate during a
head-on collision, and protect
you from serious injury. Do not
drive with your body bending to-
wards the steering wheel, but sit
in an upright position with your
back resting against the seat.
Do not cover the back-
rest of front seats with
trims or covers that are
not suitable to be used with side
bags.
It is important to re-
member that the airbag
can be fired if the ignition
key is fitted and at MAR also if
the engine is not running and the
vehicle it is hit by another vehicle
travelling at suitable speed. As a
consequence, Fiat recommends
sitting children in their specific
restraint systems on the back
seat, which is the most protected
position possible. On the con-
trary, the airbags will not be fired
if the vehicle is crashed into when
the key is not inserted or turned.
Consequently, in this case, the
fact that the system is not fired
does not indicate a fault.

100GETTING TO KNOW YOUR VEHICLE
RADIO TRANSMITTERS AND
CELLULAR TELEPHONES
Radio transceiver equipment (e.g.: e-
tacs mobile phones, HAM radio sys-
tems and the like) shall not be used in-
side the vehicle unless a separate aer-
ial is mounted on the roof.
IMPORTANTThe use of similar
devices inside the passenger compart-
ment (without separated aerial) pro-
duces radio-frequency electromag-
netic fields which, amplified by the res-
onance effects inside the passenger
compartment, may cause electrical
systems equipping the vehicle to mal-
function. This could compromise safe-
ty in addition to constituting a poten-
tial hazard for the passengers.
In addition, transmission and recep-
tion of these devices may be affected
by the shielding effect of the vehicle
body.
As concerns EC-approved mobile
phones (GSM, GPRS, UMTS), strictly
comply with the instructions for use
provided by the mobile phone’s man-
ufacturer.ACCESSORIES
PURCHASED BY THE
OWNER
If after buying the car, you decide to
install electrical accessories that re-
quire a permanent electric supply
(alarm, satellite antitheft system, etc.)
or accessories that in any case
burden the electric supply, contact
Fiat Dealership, whose qualified
personnel, besides suggesting the
most suitable devices belonging to
Lineaccessori Fiat, will also evalu-
ate the overall electric absorption,
checking whether the car’s electric sys-
tem is able to withstand the load re-
quired, or whether it needs to be in-
tegrated with a more powerful battery.
INSTALLATION OF
ELECTRIC/ ELECTRONIC
DEVICES
Electric/electronic devices installed
after buying the car or in aftermarket
shall bear the and marking:Fiat Auto S.p.A. authorizes the in-
stallation of transceivers provided that
installation is carried out at a special-
ized shop, workmanlike performed
and in compliance with manufacturer's
specifications.
IMPORTANTInstallation of de-
vices resulting in modifications of car
characteristics may cause driving li-
cense seizing by traffic agents and al-
so the lapse of the warranty as con-
cerns defects due to the abovemen-
tioned modification or traceable back
to it directly or indirectly.
Fiat Auto S.p.A.declines all re-
sponsibility for damages caused by the
installation of non-genuine accessories
or not recommended by Fiat Auto
S.p.A.and installed not in compliance
with the specified requirements.

110DRIVING YOUR VEHICLE
Some suggestions which may help
you to keep the running costs of the
vehicle down and lower the amount
of toxic emissions released into the at-
mosphere are given below.
GENERAL
CONSIDERATIONS
Vehicle maintenance
The overall state of the vehicle is an
important factor which has a marked
influence over fuel consumption and
driving comfort and on the life span of
your vehicle. For this reason care
should be taken to maintain your ve-
hicle by carrying out the necessary
checks and regulations in accordance
with the specifications given in the
SERVICE SCHEDULE (see sections:
spark plugs, idling, air cleaners, diesel
fuel filter, timing).Tyres
Tyre pressure should be checked at
least once every four weeks: if the
pressure is too low fuel consumption
increases as the resistance to the
rolling movement of the tyre is
greater. In this state, tyre wear is in-
creased and handling suffers which will
effect safety.
Unnecessary loads
Do not travel with too much load in
the boot. The weight of the vehicle
and its trim greatly effects consump-
tion and stability.
Roof rack/ski rack
Remove the roof rack or the ski rack
from the roof as soon as they are no
longer used.
These accessories reduce the aero-
dynamic penetration of the vehicle and
will increase consumption. Whentransporting particularly large objects,
use a trailer, where possible.
Electric devices
Use electric devices for the neces-
sary time only. The heated rear win-
dow, fog lights, windscreen wipers,
heater fan require large amounts of
electricity and increasing the request
for power will also increase fuel con-
sumption (up to +25% when driving in
towns).
Climate control system
The climate control system is an ad-
ditional load which greatly effects the
engine leading to higher consumption
(up to +20% in average). When the
temperature outside allows, use the
air vents where possible.
Aerodynamic accessories
The use of non-certified aerodynamic
items may adversely affect air drag and
consumption levels.
CONTAINING RUNNING COSTS AND POLLUTION

TOWING TRAILERS
IMPORTANT NOTES
The vehicle must be fitted with a ho-
mologated tow hitch and suitable elec-
trical system for towing a caravan or
trailer. Installation must be carried out
by skilled personnel who will issue
documentation authorising circulation
on the road.
Install any specific and/or additional
rear-view mirrors in accordance with
the Highway Code.
Remember that towing a trailer
makes it harder for the vehicle to
climb the maximum gradients speci-
fied.Engage a low gear when driving
downhill rather than constantly brak-
ing.
The weight the trailer exerts on the
vehicle’s tow hitch coupling reduces
the vehicle’s payload by the same
amount.
To make sure the maximum towable
weight is not exceeded (given in the
log book) account should be taken of
the fully laden trailer, including acces-
sories and personal belongings.
Respect the speed limit for towing
trailers in the country you are travel-
ling in. In any case, do not exceed a
maximum speed of 100 km/h. Do not allow anything to
be sprayed onto the cat-
alytic converter, lambda
sensor and exhaust pipe.
When functioning nor-
mally the catalytic con-
verter reaches high tem-
peratures. For this reason do not
park the vehicle over inflamma-
ble material (grass, dry leaves,
pine needles etc.): fire hazard.
Ignoring the above rules
may lead to fire.
113DRIVING YOUR VEHICLE

After 1000 km check that the tow
hitch fastening screws are perfectly
closed. Have this operation carried
out at Fiat Dealership.
IMPORTANT A clearly visible
plate of a suitable size and made of
suitable material bearing the following:
MAX LOAD ON BALL COUPLING
60 kg.
fig. 4
F0A0207b
After assembly, seal the
holes to prevent exhaust
fumes from entering the
vehicle.
SEC. A-A
Rear wheel axle
Fully laden
vehicle
Ground line
M10 screw
Existing
hole
M10 screw
Existing hole Three M8
screws
Existing nuts
Standard ball
Three M8
screws
Existing nuts
Existing hole
M10 screwM10 screw
Existing hole
115DRIVING YOUR VEHICLE