light FIAT DOBLO 2008 1.G Owner's Guide

67GETTING TO KNOW YOUR VEHICLE
– switch Apressed to the right, ceil-
ing lights Cand Dwill stay on in what-
ever condition.
When the ceiling light is off, switch
Bturns on the following lights:
– map-reading light Cif pressed to
the left;
– map-reading light Dif pressed to
the right.
IMPORTANTMake sure that both
switches are in central position before
getting out of the vehicle. This is en-
sure that the ceiling lights go out when
the doors are closed preventing the
battery from running down.
Timing for getting into the
vehicle
The ceiling lights will come on as fol-
lows:
– for 15 seconds when the front
doors are unlocked;– for 7 seconds when a door is
closed (within the three minutes).
Timing will be stopped when the ig-
nition key is turned to MAR.
Timing for getting out of the
vehicle
The ceiling lights will come on as fol-
lows when the key is removed from
the ignition switch:
– for 3 minutes within two minutes
after stopping the engine;
– for 7 seconds when a door is
closed (within the three minutes).
Timing will be stopped when the
doors are locked.WITH TOGGLE LENS
Press the short side of the lens fig.
91to switch the light on and off.
fig. 91
F0A0215b
001-105 Doblo GB 16-12-2008 14:22 Pagina 67

68GETTING TO KNOW YOUR VEHICLE
CONTROLS
HAZARD LIGHTS fig. 92
They turn on by pressing switch A,
regardless of the position of the igni-
tion key.
When the lights are on, the switch
and the instrument panel warning light
FDor Rand Ewill flash.
Press the switch again to turn the
lights off.CONTROL BUTTONS fig. 93
The buttons are located between
the central air vents.
The controls can only be operated
when the ignition key is at MAR.
A- Front foglight button.
B- Rear foglight button.
C- Heated rear window on/off but-
ton. IMPORTANTThe dipped beam
headlights will automatically be
switched off when the main beam
headlights are switched on if the front
fog lights are on.
The dipped beam headlights and/or
the front foglights (if fitted) must be on
to switch rear foglights on.
The rear fog lights are switched off
either by pressing C or switching on
the main beam headlights or turning
the ignition key to STOP. You will
need to switch the rear foglights back
on, if required, when the dipped beam
headlights and/or front foglights are
switched on or when the engine is
started again.
A
fig. 92
F0A0057b
The use of hazard lights
is governed by the High-
way Code of the country
you are in. Keep to the rules.
BA
fig. 93
F0A0509b
001-105 Doblo GB 16-12-2008 14:22 Pagina 68

70GETTING TO KNOW YOUR VEHICLE
ASHTRAY fig. 99
Pull flap Atowards yourself. Remove
the ashtray Bby pulling it upwards for
emptying it.
Non smokers can remove the ash-
tray and use it as additional oddment
compartment.
ODDMENT SHELF fig. 100
The shelf is fitted over the sunvisors.
It was designed to easily house light-
weight objects (e.g. documents, road
maps, etc.).
IMPORTANTThe shelf was de-
signed for loads not exceeding 3 kg on
each side. Consequently, do not arrange
objects exceeding these weights. Do
not use the points shown as grips fig.
100. Use the specific side handles.
B
A
fig. 99
F0A0064b
POWER SOCKET
(where provided)
The vehicle is fitted with a power
socket A-fig. 98set on the dashboard
(on the left of the gearbox) that only
works with ignition key at MAR. Do
not use current sockets for accessories
with power over 180 W (max. intake
15 A).
A
fig. 97
F0A0062b
Do not use the sockets
for accessories with pow-
er over the max. specified
one.
U-
MAX
180
WA
fig. 98
F0A0063b
Prolonged use of accessories with
high current intake could deploy the
battery, even preventing the engine
from starting.
CIGAR LIGHTER fig. 97
With ignition key at MAR: press but-
ton A; after approximately 15 seconds
it will return to its initial position and
is ready for use.
IMPORTANTAlways make sure
the cigar lighter does in fact pop out
after it has been pushed in.
Important. The cigar
lighter gets very hot.
Handle with care and do
not let children use it: danger of
fire or burns.
001-105 Doblo GB 16-12-2008 14:22 Pagina 70

71GETTING TO KNOW YOUR VEHICLE
IMPORTANTDo not position on
the tilting shelf objects heavier than 3
kg: for safety purposes the shelf is re-
leased from its housing when submit-
ted to excessive loads.
Resetting the shelf
(after releasing)
Proceed as follows:
– fit the shelf B-fig. 101bso that the
support fixed pin Ais fitted inside the
shelf left rail;
– turn the shelf Buntil the lower
edge is touching the support Amobile
pin C;
– press slightly in arrow direction to
set the shelf Bin the position of use.
Pin Cis inside the shelf right rail. SUN VISORS fig. 101
The sun visors Aare positioned to
the sides of the rear-view mirror.
They can swing up and down, as
shown. A ticket pocket can be found
on the back of the sunvisor driver's
side. A courtesy mirror is applied to
the back of the sun visors.
TILTING SHELF (for passengers
transport versions, where
provided)
Behind the front passenger seatback,
it is available (on certain versions) a
tilting shelf A-fig. 101a.
To position it horizontally, pull it to-
wards the direction shown by the ar-
rows; reverse this operation to repo-
sition it.
fig. 100
F0A0506b
A
fig. 101
F0A0507b
fig. 101b
F0A0911b
Never travel with the
shelf tilted. The shelf or
the objects on it can
cause injuries in the event of a
crash.
fig. 101a
F0A0910b
001-105 Doblo GB 16-12-2008 14:22 Pagina 71

79GETTING TO KNOW YOUR VEHICLE
When using the boot,
make sure the load you
are carrying does not ex-
ceed the permitted weight (see
“Technical specifications”). Also
ensure the items in the boot are
arranged properly to prevent
them being thrown forwards and
injuring passengers should you
brake sharply. Do not travel with
the tailgate open: exhaust gas
could filter into the passenger
compartment.
If you are travelling in
areas where refuelling
can be difficult and you
want to carry a can of petrol, fol-
low the law in force. Use a ho-
mologated can and secure it ad-
equately. Even given these pre-
cautions, the risk of fire in the
event of an accident is increased.
Do not use the key as a
handle to open the tail-
gate. You could damage it.
TAILGATE
Opening/closing the tailgate
To open the tailgate from the out-
side, turn the ignition key in lock
fig. 118and pull handle Ain the di-
rection of the arrow.
The opening of the boot is made eas-
ier by the gas-filed struts on each side.
IMPORTANTFit the key well into
the lock before turning it.
You will be able to open the tailgate
with the key only if you remove the
key from the lock after turning it by 45
degrees.
To close, lower the tailgate until the
lock clicks.
CENTRAL DOOR LOCKING
SYSTEM
From the outside
With the doors closed, fit and turn
the key in one of the front door locks.IMPORTANTAdjust the height of
the dipped headlight beam when trav-
elling at night with a rather heavy load
in the boot (see “Headlights” in this
chapter).
Make sure the load does not exceed
the values shown in “Weights” para-
graph, “Technical specifications” chap-
ter for correct operation of the head-
light adjustment device.
Do not knock the tailgate
into objects on the roof
rack when you open it.
fig. 118
F0A0231b
001-105 Doblo GB 16-12-2008 14:22 Pagina 79

82GETTING TO KNOW YOUR VEHICLE
fig. 127
F0A0433b
7-seat versions
To extend the boot, proceed as fol-
lows:
– remove head restraints;
– release the right locking lever B-
fig. 127moving it to 1(“released
lever”); do the same on the left side
then lower the seat back and tip the
seat forward. This operation is made
friendly by two springs. Make sure the
seat is completely tipped.
– refit head restraints back into the
seats C-fig. 128.
B
fig. 126
F0A0088b
4)Lift part B-fig. 126making the
shelf slide along the available space be-
hind the seat so that the upper part is
fastened to the rear window shelf and
the lower central part to the seat.
If the seat is down, proceed as fol-
lows:
5)Remove the shelf and arrange it
crosswise between the front seat
backs and the tipped seat on the rear
seat.
To refit the shelf, refit central catch-
es D-fig. 124and tip first part Band
then part A, make sure shelves are
properly secured.IMPORTANTCheck and adjust
the height of the dipped headlight
beam when travelling at night with a
rather heavy load in the boot (see
“Headlights” in this section).
To take the seat back to normal po-
sition:
1)Check that the seat belt webbing
is correctly fitted in its bracket.
2)Take the cushion to its horizontal
position and check that it is correctly
fastened.
3)Tip the seat back backwards and
check that it is correctly fastened.
001-105 Doblo GB 16-12-2008 14:22 Pagina 82

85GETTING TO KNOW YOUR VEHICLE
Important. The bonnet
might fall violently if the
support rod is not posi-
tioned properly.
When the engine is hot,
mind your hands when
working inside the engine
compartment to avoid burning
yourself. Never put your hands
near the fan: it could start up even
without the key in the switch.
Wait until the engine cools down.BONNET
To open the bonnet
This should only be done
when the vehicle is sta-
tionary. Before opening
the bonnet, check the windscreen
wiper arms are not lifted from
the windscreen.
1)Pull the yellow lever A-fig. 133
in the direction of the arrow.
2)Raise the bonnet slightly until lo-
cating the release lever.
fig. 133
F0A0082b
3)Press the fastener A-fig. 134, as
shown in the figure.
4)Open the bonnet and release the
rod A-fig. 135from its clip at the
same time. Then Bon the bonnet.
B
A
fig. 135
F0A0084b
Take care that scarves,
ties or loose clothing do
not accidentally come
near moving parts; they could be-
come entangled with serious dan-
ger for the wearer.
fig. 134
F0A0901b
001-105 Doblo GB 16-12-2008 14:22 Pagina 85

88GETTING TO KNOW YOUR VEHICLE
To use the side ramp, fig. 138,
open the side sliding door, take han-
dle Aand take out the ramp as shown
by the arrow until locking it.
IMPORTANTMax. side ramp car-
rying capacity is 60 kg.
When you have finished, take handle
Aand refit the side ramp into its hous-
ing making it sliding as shown by the
arrow fig. 138.
fig. 138
F0A0234b
HEADLIGHTS
ADJUSTING THE
HEADLIGHT BEAM
The correct positioning of the head-
light beams is very important for the
comfort and safety, not only of the
person driving the vehicle but also all
other road users.
This is also covered by a specific law.
To ensure you and other drivers
have the best visibility conditions when
travelling with the headlights on, the
headlights must be set properly.
Have the headlight positioning
checked at a Fiat Dealershipand ad-
justed if necessary.SLANT COMPENSATION
The vehicle is fitted with an electri-
cal device for correcting the headlight
slant. The device can be operated with
ignition key at MARand dipped
beams on.
When the vehicle is loaded, it
“slopes” backwards. This means that
the headlight beam rises. In this case,
it is necessary to return it to the cor-
rect position.
Proceed as follows:
– hold button B-fig. 139pressed to
increase by one position (e.g.: 0➟1,
1➟2, 2➟3);
– hold button Apressed to decrease
by one position (e.g.: 3➟2, 2➟1, 1➟0).
Display Cshows the positions dur-
ing the adjustment.
0y
1∆
70
22: 1 10
7
7B
AC
fig. 139
F0A0085b
001-105 Doblo GB 16-12-2008 14:22 Pagina 88

89GETTING TO KNOW YOUR VEHICLE
ABS
The vehicle can be fitted with an ABS
braking system, which prevents the
wheels from locking when braking,
makes the most of road grip and gives
the best control when emergency
braking under difficult road conditions.
The driver can tell the ABS system
has come into play because the brake
pedal pulsates slightly and the system
gets noisier.
This should not be interpreted as a
fault in the brakes; on the contrary it
is a sign that the ABS system is work-
ing: it tells the driver that the vehicle
is travelling at the limit of its road grip
and that he should alter his speed to
fit the type of road surface.
The ABS system is an addition to the
basic braking system. If there is a mal-
function, the system turns off auto-
matically and only the ordinary brakes
continue to work.If a failure occurs, and consequently
the anti-lock function is not effective,
the braking system will continue to
work as usual.
If you have never driven a vehicle
with ABS before, you should practice
using the system on slippery terrain,
obviously with the necessary safety
precautions and keeping to the High-
way Code of the country you are in.
It is also a good idea to read the fol-
lowing information carefully.
The advantage in using the ABS sys-
tem is that it continues to give you
maximum manoeuvrability even when
braking hard in conditions of poor grip
by preventing the wheels locking.
You should, however, not expect the
braking distance to always decrease:
for example surfaces with gravel or
fresh snow on a slippery road will in
fact increase the braking distance. Correct positions as a function
of the load
0- one or two occupants in the
front seats.
1- five occupants.
2- five occupants + load in boot.
3- driver + maximum permissible
load stowed in boot.
Check the headlight
beam position every time
you change the load to be
carried.
HEADLIGHT ADJUSTMENT
ABROAD
Headlights are orientated as to drive
inside the country of origin before sell-
ing the vehicle. When travelling in
countries with opposite driving direc-
tion, you need to cover the headlight
areas according to the Road Code of
the country you are travelling in.
001-105 Doblo GB 16-12-2008 14:22 Pagina 89

90GETTING TO KNOW YOUR VEHICLE
To exploit the ABS system to the full
in the event of necessity, you should
take heed of the following advice:
Braking while cornering always re-
quires extreme care even when using
ABS.
The most important advice to follow
is this The ABS exploits the
road hold available as
much as possible but can-
not increase it. You should always
drive carefully on slippery sur-
faces and avoid any unnecessary
risks.
If the ABS system cuts in
it is a sign that the grip
between the tyre and the
road surface has reached the lim-
it: you must slow down to match
the speed to the road grip avail-
able.
If there is a fault, the in-
strument panel warning
light >will come on. At
this point, reduce speed and go to
a Fiat Dealership to have your ve-
hicle checked and put right im-
mediately.
When the ABS cuts in,
and you feel the brake
pedal pulsating, do not re-
move your foot, but keep it
pressed. In doing so you will stop
in the shortest amount of space
possible under the current road
conditions.
If you follow these tips you will be
able to brake better in any situation.
IMPORTANTVehicles fitted with
may only be fitted with wheel rims,
tyres and brake pads of the make and
model approved by the vehicle man-
ufacturer.
The system is completed with an
EBD electronic brake force distribu-
tor which increases the brake system
performance and employs the ABS
control unit and sensors.
The vehicle is fitted with
an electronic braking de-
vice (EBD). The >and
xwarning light will come on at
the same time when the engine
is running to indicate that there
is an EBD system failure. In this
case violent braking may be ac-
companied by early rear wheel
locking with the possibility of
skidding. Drive the vehicle ex-
tremely carefully to the nearest
Fiat Dealership to have the sys-
tem checked.
001-105 Doblo GB 16-12-2008 14:22 Pagina 90