Wheel FIAT FULLBACK 2016 1.G Manual PDF

Wheel condition
340) 341) 342)
178)
1. Location of the tread wear indicator
2. Tread wear indicator
Check the tyres for cuts, cracks and
other damage. Replace the tyres if
there are deep cuts or cracks. Also
check each tyre for pieces of metal or
pebbles.
The use of worn tyres can be very
dangerous because of the greater
chance of skidding or hydroplaning.
The tread depth of the tyres must
exceed 1.6 mm in order for the tyres to
meet the minimum requirement for use.
Tread wear indicators will appear on the
surface of the tyre as the tyre wears,
thereby indicating that the tyre no
longer meets the minimum requirement
for use. When these wear indicatorsappear, the tyres must be replaced with
new ones.
In the case of the 4-wheel drive
vehicles, when replacement of any of
the tyres is necessary, replace all of
them.
Replacing tyres and wheels
179) 180)
Tyre rotation
Tyre wear varies with vehicle conditions,
road surface conditions and individual
driver’s driving habits. To equalize the
wear and help extend tyre life, it is
recommended to rotate the tyres
immediately after discovery of abnormal
wear, or whenever the wear difference
between the front and rear tyres is
recognizable.
When rotating tyres, check for uneven
wear and damage. Abnormal wear is
usually caused by incorrect tyre
pressure, improper wheel alignment,
out of balance wheel, or severe braking.
Consult your authorised Fiat dealer to
determine the cause of irregular tread
wear.
181) 182)
1
2
409AA0002549
410AHE100140
262
SERVICING AND MAINTENANCE

Snow tyres
183)
The use of snow tyres is recommended
for driving on snow and ice. To preserve
driving stability, mount snow tyres of the
same size and tread pattern on all four
wheels. Snow tyres worn more than 50
% are no longer suitable for use as
snow tyres. Snow tyres which do not
meet specifications must not be used.
The laws and regulations concerning
snow tyres (driving speed, required use,
type, etc.) vary. Find out and follow the
laws and regulations in the area you
intend to drive.
If flange nuts are used on your vehicle,
change to tapered nuts when steel
wheels are used.
Tyre chains
343)
184) 185) 186) 187) 188) 189) 190) 191)
It is recommended that snow chains
are carried in snow regions and fitted
when required to the rear wheels.
On 4WD vehicles in which the driving
power is distributed preferentially to the
rear wheels, ensure that the tyre chains
are fitted on the rear.
The tyres fitted to your vehicle as
original equipment allow you to fit tyre
chains if they are required. When
replacing your tyres, check with the tyre
distributor or manufacturer if the fitting
of tyre chains will be detrimental to the
tyres being purchased.
Always follow the chain manufacturer’s
instructions when fitting the chains.
The laws and regulations concerning
the use of tyre chains vary. Find out and
follow the laws and regulations in
driving area. In most countries, it is
prohibited by the law to use tyre chains
on roads without snow.
WARNING
339)Driving with tyres that are worn,
damaged or improperly inflated can lead to
a loss of control or blow out of the tyres
which can result in a collision with serious
or fatal injury.340)Remember that the road holding
qualities of your vehicle also depend on the
correct inflation pressure of the tyres.
341)If the pressure is too low, the tyre will
overheat and could be seriously damaged.
342)Never submit alloy rims to repainting
treatments requiring the use of
temperatures exceeding 150°C. The
mechanical properties of the wheels could
be impaired.
343)DO NOT use a jack when fitting the
chains, as in the conditions, the tyres may
slip on the icy road causing the vehicle to
slip off the jack.
IMPORTANT
178)Always use tyres of the same size,
same type, and same brand, and which
have no wear differences. Using tyres of
different size, type, brands or degree of
wear, will increase the differential oil
temperature, resulting in possible damage
to the driving system. Further, the drive
train will be subjected to excessive loading,
possibly leading to oil leakage, component
seizure, or other serious faults.
179)Avoid using different size tyres from
the one listed and the combined use of
different types of tyres, as this can affect
driving safety.
180)Even if a wheel has the same rim size
and offset as the specified type of wheel,
its shape may prevent it from being fitted
correctly. Consult a Fiat dealership before
using wheels that you have.
A
411AA0002552
263

181)If the tyres have arrows (A) indicating
the correct direction of rotation, swap the
front and rear tyres on the left hand side of
the vehicle and the front and rear tyres on
the right hand side of the vehicle separately.
Keep each tyre on its original side of the
vehicle. When fitting the tyres, make sure
the arrows point in the direction in which
the wheels will turn when the vehicle moves
forward. Any tyre whose arrow points in the
wrong direction will not perform to its full
potential.
182)Avoid the combined use of different
types of tyres. Using different types of tyres
can affect vehicle performance and safety.
183)If winter tyres with a lower speed
rating than that indicated in the Registration
Document are used, do not exceed the
maximum speed corresponding to the
speed rating of the tyres used.
184)Do not fit snow traction device (Tyre
chains) before you need them. This will
wear out your tyres and the road surface.
185)After driving around 100-300 metres,
stop and retighten the snow traction device
(Tyre chains).
186)Care should be taken with extremes of
steering lock to prevent possible contact
between the chains and the vehicle body.
187)Drive cautiously and do not exceed
50 km/h. Remember that preventing
accidents is not the purpose of snow
traction device (tyre chains).
188)When tyre chains are installed, take
care that they do not damage the disc
wheel or body.189)An aluminium wheel can be damaged
by a snow traction device (Tyre chains)
while driving. When fitting a snow traction
device (Tyre chains) on an aluminium wheel,
take care that any part of the snow traction
device (Tyre chains) and fitting cannot be
brought into contact with the wheel.
190)When installing or removing a tyre
chain, take care that hands and other parts
of your body are not injured by the sharp
edges of the vehicle body.
191)Install the chains only on the rear tyres
and tighten them as tightly as possible with
the ends securely fastened.
264
SERVICING AND MAINTENANCE

TECHNICAL SPECIFICATIONS
Everything you may find useful for
understanding how your vehicle is
made and works is contained in this
chapter and illustrated with data, tables
and graphics. For the enthusiasts and
the technician, but also just for those
who want to know every detail of their
vehicle.VEHICLE LABELING..........266
ENGINE SPECIFICATIONS......268
VEHICLE DIMENSIONS........271
VEHICLE PERFORMANCE......279
VEHICLE WEIGHTS..........281
ELECTRICAL SYSTEM.........289
TYRES AND WHEELS.........291
REFILL CAPACITIES..........292
FLUIDS AND LUBRICANTS......300
265

Reference Length
1 Front track1,520 mm
2 Overall width1,815 mm
3 Front overhang865 mm
4 Wheel base3,000 mm
5 Rear overhangWithout rear bumper 1,330 mm
With rear bumper 1,410 mm
6 Overall lengthWithout rear bumper 5,195 mm
With rear bumper 5,275 mm
7 Ground clearance (unladen) 205 mm
8 Overall height (unladen) 1,780 mm
9 Rear track1,515 mm
10 Cargo bed length1,850 mm
11 Cargo bed width1,470 mm
12 Cargo bed height850 mm
Minimum turning radiusBody 6.3 m
Wheel 5.9 m
The vehicle overall length and height may vary depending on the equipment installed.
272
TECHNICAL SPECIFICATIONS

Item 2WD2WD Hi-Rider
Vehicles without wide
fender2WD Hi-Rider
Vehicles with wide fender
1 Front track 1,520 mm
2 Overall width 1,785 mm 1,785 mm 1,815 mm
3 Front overhang
860 mm, 865 mm
(1)
4 Wheel base 3,000 mm
5 Rear overhangWithout rear
bumper1,340 mm
With chrome
rear bumper1,485 mm
With silver rear
bumper— 1,420 mm
6 Overall lengthWithout rear
bumper5,200 mm, 5,205 mm
(1)
With chrome
rear bumper5,345 mm, 5,350 mm(1)
With silver rear
bumper——
5,280 mm, 5,285 mm(1)
7Ground clearance
(unladen)200 mm 200 mm 205 mm
8Overall height
(unladen)1,655 mm 1,775 mm 1,780 mm
9 Rear track 1,515 mm
10 Cargo bed length 1,520 mm
11 Cargo bed width 1,470 mm
12 Cargo bed height 715 mm 845 mm 850 mm
(1) Vehicles equipped with licence garnish
274
TECHNICAL SPECIFICATIONS

Item 2WD2WD Hi-Rider
Vehicles without wide
fender2WD Hi-Rider
Vehicles with wide fender
Minimum turning radiusBody 6.1 m 6.3 m
Wheel 5.7 m 5.9 m
Item4WD Hi-Rider
Vehicles without wide fender4WD Hi-Rider
Vehicles with wide fender
1 Front track1,520 mm
2 Overall width 1,785 mm 1,815 mm
3 Front overhang
860 mm, 865 mm
(1)
4 Wheel base 3,000 mm
5 Rear overhang Without rear bumper 1,340 mm
With chrome rear
bumper1,485 mm
With silver rear
bumper1,420 mm
6 Overall length Without rear bumper
5,200 mm, 5,205 mm
(1)
With chrome rear
bumper5,345 mm, 5,350 mm(1)
With silver rear
bumper5,280 mm, 5,285 mm(1)
7Ground clearance
(unladen)200 mm, 220 mm(2)205 mm, 220 mm(2)
8 Overall height (unladen)
1,775 mm, 1,795 mm(2)1,780 mm, 1,795 mm(2)
(1) Vehicles equipped with licence garnish
(2) Vehicles with 265/70 R16 size tyre or 245/75 R16 size tyre
275

Item4WD Hi-Rider
Vehicles without wide fender4WD Hi-Rider
Vehicles with wide fender
9 Rear track1,515 mm
10 Cargo bed length 1,520 mm
11 Cargo bed width 1,470 mm
12 Cargo bed height
845 mm, 865 mm
(2)850 mm, 865 mm(2)
Minimum turning radiusBody 6.3 m
Wheel 5.9 m
(2) Vehicles with 265/70 R16 size tyre or 245/75 R16 size tyre
276
TECHNICAL SPECIFICATIONS

Item 2WD 2WD Hi-Rider 4WD
1 Front track1,520 mm
2 Overall width1,785 mm
3 Front overhang 860 mm, 865 mm
*1865 mm 860 mm, 865 mm*1
4 Wheel base3,000 mm
5 Rear overhangWithout rear bumper 1,215 mm
With rear bumper 1,360 mm - 1,360 mm
6 Overall lengthWithout rear bumper 5,075 mm, 5,080 mm
*15,080 mm 5,075 mm, 5,080 mm*1
With rear bumper 5,220 mm, 5,225 mm*1- 5,220 mm, 5,225 mm*1
7 Ground clearance (unladen) 200 mm
8 Overall height (unladen) 1,655 mm 1,765 mm, 1,780 mm
*21,780 mm
9 Rear track1,515 mm
10 Cargo bed length 2,265 mm
11 Cargo bed width 1,470 mm
12 Cargo bed height 710 mm 840 mm 845 mm
Minimum turning radiusBody 6.1 m 6.3 m
Wheel 5.7 m 5.9 m
*1: Vehicles equipped with licence plate garnish*2: Vehicles equipped with rear guard frame
278
TECHNICAL SPECIFICATIONS

TYRES AND WHEELS
Tyre size
Tyres195R15C
106/104R 8PR205R16C
110/108R 8PR245/
70R16 111S RF265/
70R16 112SLT245/
75R16 120/
116Q245/
65R17 111S RF
WheelSize 15x6J, 15x6JJ 16x6J, 16x6JJ 16x7J, 16x7JJ 17x7 1/2J
Offset 38 mm
Contact a Fiat Dealership for details on the combination used on your vehicle.
Tyre inflation pressure
Tyre sizeNo cargo Cargo
Front Rear Front Rear
245/65R17 111S RF220 kPa (32 p.s.i/
2.2 kgf/cm2)220 kPa (32 p.s.i/
2.2 kgf/cm2)220 kPa (32 p.s.i/
2.2 kgf/cm2)290 kPa (42 p.s.i/
2.9 kgf/cm2)
LT245/75R16 120/116Q250kPa (36 p.s.i/
2.5 kgf/cm
2)250kPa (36 p.s.i/
2.5 kgf/cm2)250kPa (36 p.s.i/
2.5 kgf/cm2)350kPa (51 p.s.i/
3.5 kgf/cm2)
245/70R16 111S RF200 kPa (29 p.s.i/
2.0 kgf/cm
2)200 kPa (29 p.s.i/
2.0 kgf/cm2)200 kPa (29 p.s.i/
2.0 kgf/cm2)290 kPa (42 p.s.i/
2.9 kgf/cm2)
205R16C 110/108R 8PR240 kPa (35
p.s.i/2.4 kgf/cm
2)240 kPa (35
p.s.i/2.4 kgf/cm2)240 kPa (35
p.s.i/2.4 kgf/cm2)450 kPa (65
p.s.i/4.5 kgf/cm2)
265/70R16 112S180kPa (26 p.s.i/
1.8 kgf/cm
2)200 kPa (29 p.s.i/
2.0 kgf/cm2)200 kPa (29 p.s.i/
2.0 kgf/cm2)250kPa (36 p.s.i/
2.5 kgf/cm2)
195R15C 106/104R 8PR220 kPa (32 p.s.i/
2.2 kgf/cm
2)220 kPa (32 p.s.i/
2.2 kgf/cm2)220 kPa (32 p.s.i/
2.2 kgf/cm2)450 kPa (65
p.s.i/4.5 kgf/cm2)
291