fuel FIAT IDEA 2012 1.G Owner's Guide
[x] Cancel search | Manufacturer: FIAT, Model Year: 2012, Model line: IDEA, Model: FIAT IDEA 2012 1.GPages: 210, PDF Size: 3.65 MB
Page 174 of 210

173
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
DIESEL FUEL FILTER
(“green filter”)
DRAINING THE CONDENSE
(diesel versions)
The presence of water in the
fuel circuit may cause seri-
ous damage to the entire injection
system and cause irregular engine op-
eration. If the warning light
cturns
on (or on certain versions, a dedicat-
ed message is shown on the reconfig-
urable multifunction display) contact
a Fiat Dealership as soon as possible
to have the bleeding operation car-
ried out. Should the above indications
take place after refuelling, water has
probably been poured into the tank:
turn the engine off immediately and
contact a Fiat Dealership.
WARNING
BATTERY
The battery is of the “Limited mainte-
nance” type: under normal conditions of
use the electrolyte does not need topping
up with distilled water.
INSPECTING THE CHARGE
AND THE ELECTROLYTE LEVEL
Inspection operations must be carried out
by specialised personnel, following the
prescriptions contained in the Owner
Handbook.
Any top-up operations must be carried
out exclusively by specialised personnel
and by the Fiat Dealership.
Battery liquid is poisonous
and corrosive. Avoid contact
with the skin and eyes. Keep naked
flames or possible sources of sparks
away from the battery: risk of explo-
sion or fire.
WARNING
CHANGING THE BATTERY
If required, replace the battery with a gen-
uine spare part having the same specifi-
cations.
If a battery with different specifications is
fitted, the service intervals given in the
“Service schedule” in this section will no
longer be valid.
Refer therefore to the instructions pro-
vided by the battery manufacturer.
Using the battery when the
fluid is too low can damage
it irreparably and generate a risk of
explosion.
WARNING
Incorrect assembly of electric
and electronic devices may
cause severe damage to your
car. Go to a Fiat Dealership if
you want to install accessories (alarms,
mobile phone, etc.): they will suggest
the most suitable devices and advise
you if a higher capacity battery needs
to be installed.
161-180 idea GB 1 ed 10-07-2008 8:30 Pagina 173
Page 177 of 210

176
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
RUBBER HOSES
As far as the brake system and fuel rubber
hoses are concerned, carefully follow the
“Service schedule” in this section.
Indeed ozone, high temperatures and pro-
longed lack of fluid in the system may
cause hardening and cracking of the hoses,
with possible leaks. Careful control is
therefore necessary.
WINDSCREEN/
REAR WINDOW
WIPERS
BLADES
Periodically clean the rubber part using
special products; TUTELA PROFES-
SIONAL SC 35 is recommended.
If the rubber blades are bent or worn they
should be replaced. In any case they
should be changed once a year.
A few simple notions can reduce the pos-
sibility of damage to the blades:
❒if the temperature fall below zero,
make sure that ice has not frozen the
rubber against glass. If necessary, thaw
using an antifreeze product;
❒remove any snow from the glass: in ad-
dition to protecting the blades, this
prevents effort on the motor and
overheating;
❒do not operate the windscreen and
rear window wipers on dry glass.
Driving with worn wiper
blades is a serious hazard,
because visibility is reduced in bad
weather.
WARNING
Changing the windscreen wiper
blades fig. 14
Proceed as follows:
❒raise the windscreen wiper arm Aand
position the blade so that it forms an
angle of 90° with the arm;
❒press tab Bof the coupling spring and
remove the blade to be replaced from
the arm A;
❒fit the new blade by inserting the tab
into the special slot in the arm. Make
sure it is properly locked into place.
161-180 idea GB 1 ed 10-07-2008 8:30 Pagina 176
Page 182 of 210

181
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IDENTIFICATION DATA ................................................. 182
ENGINE CODES - BODYWORK VERSIONS .............. 184
ENGINE ................................................................................. 185
FUEL FEED/IGNITION ....................................................... 187
TRANSMISSION .................................................................. 187
BRAKES ................................................................................... 188
SUSPENSIONS ....................................................................... 188
STEERING............................................................................... 188
WHEELS .................................................................................. 189
DIMENSIONS ........................................................................ 193
PERFORMANCE ................................................................... 193
WEIGHTS ............................................................................... 194
CAPACITIES........................................................................... 195
FLUIDS AND LUBRICANTS ............................................. 196
FUEL CONSUMPTION ....................................................... 198
CO
2EMISSIONS ................................................................. 199
TT T
E E
C C
H H
N N
I I
C C
A A
L L
S S
P P
E E
C C
I I
F F
I I
C C
A A
T T
I I
O O
N N
S S
181-199 idea GB 1 ed 10-07-2008 8:31 Pagina 181
Page 186 of 210

185
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
1.48V (◊)
350A1000
Otto
4 in line
2
72 x 84
1368
11 ± 0.2
57
77
6000
115
11.7
3000
NGK ZKR7A-10
Unleaded petrol
95 RON
(EN228 Specifications)
ENGINE
GENERAL FEATURES
Engine code
Cycle
Number and layout of cylinders
Valves per cylinder
Piston bore and stroke mm
Total displacement cm3
Compression ratio
Maximum power (EEC) kW
HP
corresponding ratio: rpm
Maximum torque (EEC) Nm
kgm
corresponding ratio: rpm
Spark plugs
Fuel
(◊) Engine model provided for certain versions/markets only
1.216V
188A5000
Otto
4 in line
4
70.8 x 78.86
1242
10.6 ± 0.2
59
80
5000
114
11.6
4000
NGK DCPR7E-N-10
BOSCH YR7DEU
Unleaded petrol
95 RON
(EN228 Specifications)1.4
16V
843A1000
Otto
4 in line
4
72 x 84
1368
11 ± 0.2
70
95
5800
128
13
4500
NGK ZKR7A-10
Unleaded petrol
95 RON
(EN228 Specifications)
181-199 idea GB 1 ed 10-07-2008 8:31 Pagina 185
Page 187 of 210

186
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
GENERAL FEATURES
Engine code:
Cycle:
Number and layout of cylinders:
Valves per cylinder:
Piston bore and stroke mm:
Total displacement cm3
:
Compression ratio:
Maximum power (EEC): kW
HP
corresponding ratio: rpm
Maximum torque (EEC): Nm
kgm
corresponding ratio: rpm
Spark plugs:
Fuel:
1.6 Multijet
350A2000
Diesel
4 in line
4
79.5 x 80.5
1598
16.5 ±1
88
120
3500
300
30.5
1500
–
Diesel fuel
for motor vehicles
(EN590 Specifications) 1.3 Multijet 70 HP
188A9000
Diesel
4 in line
4
69.6 x 82
1248
18 ±0.4
51
70
4000
180
18.3
1750
–
Diesel fuel
for motor vehicles
(EN590 Specifications)1.3 Multijet 90 HP
199A3000
Diesel
4 in line
4
69.6 x 82
1248
17.6 ±0.4
66
90
4000
200
20
1750
–
Diesel fuel
for motor vehicles
(EN590 Specifications)
181-199 idea GB 1 ed 10-07-2008 8:31 Pagina 186
Page 188 of 210

187
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
TRANSMISSION
Gearbox
Clutch
Drive
(◊) Engine model provided for certain versions/markets only1.2
16V - 1.48V (◊)- 1.3 Multijet - 1.6 Multijet
Five forward gears and reverse with synchromesh
for forward gear engagement
Hydraulic control, self-adjusting without
travel-free pedal
Front1.416V
Five or six forward gears and reverse with
synchromesh for forward gear engagement
Hydraulic control, self-adjusting without travel-free
pedal
Front
Modifications or repairs to the fuel system that are not carried out properly or do not take the system’s techni-
cal specifications into account can cause malfunctions leading to the risk of fire.
FUEL FEED/IGNITION
Fuel feed
(◊) Engine model provided for certain versions/markets only1.3 Multijet - 1.6 Multijet
Direct injection with electronically controlled
Multijet “Common Rail” with turbosupercharger
and intercooler 1.2
16V - 1.48V (◊) - 1.416V
Multipoint sequential phased electronic injection,
returnless system
181-199 idea GB 1 ed 10-07-2008 8:31 Pagina 187
Page 195 of 210

194
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
1.216V
1155
500
940
805
1655
1000
400
75
601.4
8V(◊) - 1.416V
1155
500
940
805
1655
1000
400
75
601.3 Multijet
1200
500
940
805
1700
1000
400
75
60
WEIGHTS
Weights (kg)
Empty weight
(including all fluids, fuel tank at 90 %
and with no optional):
Payload (*)
including the driver:
Maximum admitted
loads (**)
– front axle:
– rear axle:
– total:
Towable loads:
– trailer with brakes:
– trailer without brakes:
Maximum load on roof:
Maximum load on tow hitch
(trailer with brakes):
(*) If special equipment is fitted (sunroof, tow hitch, etc.) the unladen car weight increases thus reducing the specified payload.
(**) Loads not to be exceeded. The driver is responsible for arranging the loads in the boot an/or on the roof so that they comply with
these limits.
(◊) Engine model provided for certain versions/markets only1.6 Multijet
1275
500
1000
805
1775
1100
500
75
60
181-199 idea GB 1 ed 10-07-2008 8:31 Pagina 194
Page 196 of 210

195
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
1.416V1.216V1.3 Multijet1.6 Multijet1.48V (◊)
CAPACITIES
Fuel tank:
including
a reserve of:
Fuel tank:
including
a reserve of:
Engine cooling
system:
Engine sump:
Engine sump
and filter:
Engine sump:
Engine sump
and filter:
Gearbox/
differential casing:
Hydraulic
brake circuit:
Windscreen and
rear window washer
fluid reservoir:
(❒) When the vehicle is used under particularly harsh climate conditions, we recommend using a 60-40 mixture of PARAFLU UP and deminer-
alised water.Specified fuels
Recommended products
Unleaded Premium petrol
with no less than 95 R.O.N
(EN228 Specifications)
Diesel fuel for motor
vehicles
(Specification EN590)
Mixture of distilled water and
PARAFLU UPat 50%
(❒)
SELENIA 20K (❒)
SELENIA WR
TUTELA CAR
TECHNYX
TUTELA TOP 4
Mixture of water and
TUTELA
PROFESSIONAL SC 35 litres
–
–
47
5 - 7
7.8
–
–
4.4
4.7
–
0.45
1.5kg
–
–
–
–
–
–
–
3.74
4.0
1.6
–
– litres
47
5 - 7
–
–
4.5
2.75
2.9
–
–
1.65
0.45
1.5 kg
–
–
–
–
–
2.4
2.55
–
–
1.5
–
– litres
47
5 - 7
–
–
4.5
2.5
2.7
–
–
1.65
0.45
1.5kg
–
–
–
–
–
2.2
2.35
–
–
1.5
–
–litres
47
5 - 7
–
–
4.5
2.4
2.6
–
–
1.65
0.45
1.5kg
–
–
–
–
–
2.1
2.25
–
–
1.5
–
–litres
–
–
47
5 - 7
6.0
–
–
2.85
3.0
1.98
0.45
1.5kg
–
–
–
–
–
–
–
2.54
2.65
1.8
–
–
181-199 idea GB 1 ed 10-07-2008 8:31 Pagina 195
Page 198 of 210

197
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
Windscreen/
rear window Protective agent
for radiator Brake liquid Lubricants and
greases for
transmission
Use
(●) IMPORTANT Do not add or mix with fluids with specifications other than the specified ones.
(❒) When the vehicle is used under particularly harsh climate conditions, we recommend using a 60-40 mixture of PARAFLU UP and demineralised water.
Fluid and lubricant specifications
for correct car operation
Fully synthetic oil, grade SAE 75W-85 that passes API GL-4
PLUS, FIAT 9.55550 MIL-L- 2105 D LEV. Specifications
Qualification FIAT 9.55550-MX3
Specific transmission fluid with “ATF DEXTRON III”
type additives.
Qualification FIAT 9.55550-AG2
Grease containing Molybdenum bisulphide for high
temperature appliances. N.L.G.I. 1-2 consistency.
Qualification FIAT 9.55580
Poly-urea oil synthetic-based grease suitable for high
temperatures. NL.GI. 2 consistency
Qualification FIAT 9.55580
Specifc grease to be used for constant-velocity joints with
low friction coefficient. N.L.G.I. 0-1 consistency.
Qualification FIAT 9.55580
Synthetic fluid FMVSS no. 116 DOT 4, ISO 4925 SAE J1704,
CUNA NC 956- 0
Qualification FIAT 9.55597
Red protective with antifreeze action, based on inhibited
monoethylen glycol with organic formula based on O.A.T,
that passes CUNA NC 956-16, ASTM D 3306 specifications.
Qualification FIAT 9.55523
Additive for diesel fuel, protecting Diesel engines.
Mixture of alcohol, water and surfactants CUNA NC 956-II
Qualification FIAT 9.55522Original fluids
and lubrificants
TUTELA CAR
TECHNYX
Contractual Technical
Reference
N° F010.B05
TUTELA CAR GI/E
Contractual Technical
Reference
N° F001.C94
TUTELA ALL STAR
Contractual Technical
Reference
N° F702.G07
TUTELA STAR 325
Contractual Technical
Reference
N° F301.D03
TUTELA STAR 700
Contractual Technical
Reference
N° F701.C07
TUTELA TOP 4
Contractual Technical
Reference
N° F001.A93
PARAFLU UP (●)
Contractual Technical
Reference
N° F101.M01
TUTELA DIESEL ART
Contractual Technical
Reference
N° F601.L06
TUTELA PROFES-
SIONAL SC 35
Contractual Technical
Reference N° F201.D02 Additive for
diesel fluidApplications
Mechanical gearbox
and differential
Hydraulic power
steering
CV joints
on wheel side
CV joints on differential
side (1.4 16V)
CV joints on
differential side
Brake and clutch
hydraulic controls
Cooling circuits
Proportion: 50% down
to -35° C (❒). Not to be
mixed with products
having different formulas
To be mixed with fuel
oil(25 cc per 10 litres)
To be used diluted or
undiluted in windscreen/
rear window washer/
wiper systems
181-199 idea GB 1 ed 10-07-2008 8:31 Pagina 197
Page 199 of 210

198
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
FUEL CONSUMPTION
The fuel consumption figures given in the table below are determined on the basis of the homologation tests set down by specific
European Directives.
The procedures below are followed for measuring consumption:
❒urban cycle: cold starting followed by driving that simulates urban use of the car;
❒extra-urban cycle: frequent accelerating in all gears, simulating extraurban use of the car; the speed varies between 0 and
120 km/h;
❒combined consumption: is calculated weighing about 37% of urban cycle consumption and about 63% of extraurban
consumption.
IMPORTANT The type of route, traffic situations, weather conditions, driving style, general conditions of the car, trim level/equip-
ment/accessories, load, climate control system, roof rack, other situations that affect air drag may lead to different fuel consump-
tion levels than those measured.
Fuel consumption according to Directive 1999/100/EC (litres x 100 km)Urban Extra-urban Combined
1.216V8,4 5,4 6,5
1.48V(◊) 7,9 5,2 6,2
1.416V (5 gears) 8,5 5,5 6,6
1.416V (6 gears) 8,7 5,4 6,6
1.3 Multijet 70HP 5,7 4,0 4,6
1.3 Multijet 90HP 5,8 3,9 4,6
1.6 Multijet 6,2 4,2 4,9
(◊) Engine model provided for certain versions/markets only
181-199 idea GB 1 ed 10-07-2008 8:31 Pagina 198