spare wheel FIAT IDEA 2012 1.G Owners Manual

121
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
SNOW CHAINS
Use of snow chains should be in compli-
ance with local regulations.
Snow chains should only be applied to the
driving wheels (front wheels). We rec-
ommend using Lineaccessori Fiat snow
chains.
Check the tension of the chains after dri-
ving some ten metres.IMPORTANT Snow chains cannot be fit-
ted to the space-saver spare wheel. So, if
a front (drive) wheel is punctured and
chains are needed, a rear wheel should be
fitted to the front of the vehicle and the
spare wheel should be fitted to the rear.
This way with two normal drive wheels,
snow chains can be fitted to them to solve
an emergency.
IMPORTANT Tyres 205/50 R16 87V can-
not be fitted with snow chains.
Versions
ACTIVE
DYNAMIC
EMOTION
Tyres on which chains can be fitted
185/65 R14 86T
195/60 R15 88T
195/60 R15 88T
195/60 R15 88T
Type of snow chains to be used
Snow chains with standard size
with max protrusion beyond the tyre profile of 12 mm.
Keep your speed
down when snow
chains are fitted. Do
not exceed 50 km/h.
Avoid potholes, steps and pavements
and avoid also to drive for long dis-
tances on roads not covered with snow
to prevent damaging the car and the
roadbed.
Refer to the above mentioned
table for information on the
wheels where snow chains can
be fitted. Follow the prescrip-
tions.
111-122 idea GB 1 ed 10-07-2008 8:29 Pagina 121

140
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
IF A TYRE IS
PUNCTURED
GENERAL INSTRUCTIONS
Wheel changing and correct use of the
jack and space-saver spare wheel call for
some precautions as listed below.
WARNING If the car is equipped with
“Kit for tyre quick repair Fix & Go”, see
the instructions contained in the follow-
ing chapter.
The space-saver spare wheel
is specific to the vehicle: do
not use it on other models and do not
use spare wheels designed for other
models on your car. The space-saver
spare wheel must only be used in the
event of an emergency, and then on-
ly for as little as possible and at no
more than 80 km/h. The space-saver
spare wheel is fitted with an orange
sticker giving the main instructions for
its use and limitations. The sticker
must never be removed or covered.
Do not fit the hub cap to the spare
wheel. The sticker gives the following
information in four languages: C
AU-TION! FOR TEMPORARY USE ONLY! 80KM/H MAX! REPLACE BY NORMAL WHEEL
AS SOON AS POSSIBLE. DO NOT COVER THIS
LABEL IN USE.
WARNING
When driving with a space-
saver spare wheel fitted, the
driving performance of your car may
change. Avoid accelerating or brak-
ing suddenly, steering abruptly or fast
cornering. The lifespan of a space-
saver spare wheel is approximately
3000 km, after which it will need to
be replaced with another spare wheel
of the same type. Never fit a standard
tyre on the space-saver spare wheel
rim. Have the wheel replaced and re-
fitted as soon as possible. Never use
two or more spare wheels at the same
time. Do not lubricate the bolt
threads before fitting them back: they
could come loose.
WARNING
133-160 idea GB 1 ed 10-07-2008 8:30 Pagina 140

141
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
The jack should only be used
to change a wheel on the car
for which it was designed. It should
not be put to other uses or employed
to raise other models of cars. Under
no circumstances should it be used
when carrying out repairs under the
car. An incorrectly positioned jack
may cause the car to fall. Do not use
the jack to lift loads exceeding that
indicated on the label attached to the
jack itself. Do not fit snow chains on
a space-saver spare wheel. If a front
wheel (drive wheel) is punctured and
you require snow chains to proceed,
take a standard wheel from the rear
axle and fit the space-saver spare
wheel in its place. Having fitted two
standard wheels on the front drive
axle you can use snow chains, thus
solving the emergency situation.
WARNING
Fasten the wheel cap cor-
rectly to prevent the wheel
from coming free in motion. Never
tamper with the inflation valve. Nev-
er place tools between the rim and
tyre. Check the tyre and space-saver
spare wheel pressure regularly. The
tyre inflation pressure is shown in the
“Technical specifications” chapter.
WARNINGPlease note:
❒the jack cannot be repaired. If it breaks
it must be replaced with a new jack;
❒no tool other than its cranking device
may be fitted on the jack.
To change a wheel proceed as follows:
❒Stop the car in a position that is not
dangerous for oncoming traffic where
you can change the wheel safely. The
ground should be flat and adequately
firm;
❒Turn the engine off and pull up the
handbrake;
❒Engage first gear or reverse;
❒Lift the luggage compartment panel
mat;
❒Loosen the fastener A-fig. 11;
❒Take the tool bag Band go to the
wheel to be replaced;
❒Take the space-saver spare wheel C;
❒If the car is fitted with alloy rims, re-
move the wheel hub with the screw-
driver provided levering in the groove
E-fig. 12, as shown in the figure;
133-160 idea GB 1 ed 10-07-2008 8:30 Pagina 141

142
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
❒Loosen the bolts on the wheel to be
replaced by about one turn with the
wrench provided E-fig. 12; if the car
is fitted with alloy rims, shake the car
to facilitate removing this rim from the
wheel hub;
❒Operate the device F-fig. 12and ex-
tend the jack until groove Gon the
jack fits correctly into ridge Hon the
body near sign I(at about 60 cm from
the front wheel centre or 80 cm from
the rear wheel centre);
fig. 12F0H0750m
❒Warn anybody nearby that the car is
about to be lifted. They must stay clear
and not touch the vehicle until it is
back on the ground;
❒Fit the handle L-fig. 14to operate the
jack and lift the car until the wheel to
be changed is several centimetres off
the ground;
❒For versions with wheel cap, remove
the wheel cap after unloosing the
three fastening bolts and finally un-
loose the fourth bolt and extract the
wheel.
❒Make sure the contact surfaces be-
tween spare wheel and hub are clean
so that the fastening bolts will not
come loose;
fig. 13F0H0751m
❒Fit the spare wheel making the holes
M-fig. 15coincide with the respective
centring pins N;
❒Using the wrench provided, fully tight-
en the four fastening bolts;
❒Turn the jack handle L-fig. 14to low-
er the car and remove the jack;
❒Use the wrench provided to fasten the
bolts completely in a criss-cross fash-
ion as shown in the figure.fig. 11F0H0161m
133-160 idea GB 1 ed 10-07-2008 8:30 Pagina 142

143
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
fig. 14F0H0164m
fig. 15F0H0165m
fig. 16F0H0166m
REFITTING THE STANDARD
WHEEL
Following the procedure described previ-
ously, raise the car and remove the spare
wheel.
For versions with steel rim
Proceed as follows:
❒Make sure the contact surfaces be-
tween standard wheel and hub are
clean so that the fastening bolts will
not come loose;
❒Fit the standard wheel by inserting the
first bolt in the hole closest to the in-
flation valve;
❒Fit the wheel cap making the groove
(on the wheel cap) coincide with the
inflation valve and fit the other three
bolts;
❒Using the wrench provided, tighten
the fastening bolts;
❒Lower the car and remove the jack;
❒Using the wrench provided, fully
tighten the bolts in the sequence
shown previously for the spare
wheel;IMPORTANT Incorrect fitting may cause
the wheel cap to come off when the car is
travelling.
133-160 idea GB 1 ed 10-07-2008 8:30 Pagina 143

144
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
WHEN NEEDING TO
CHANGE A BULB
GENERAL INSTRUCTIONS
❒When a light is not working, check
that it has not fused before changing
the bulb. For the location of the fuses,
refer to “If a fuse blows” in this chap-
ter;
❒Before replacing a bulb that does not
work, check that the contacts are not
oxidised;
❒Burnt bulbs must be replaced by oth-
ers of the same type and power;
❒Always check the height of the head-
light beam after changing a bulb. For versions with alloy rims
❒Make sure that hub contact surfaces
are clean;
❒Refit the standard wheel fitting it on
the pins, refit the fastening bolts and
tighten them using the wrench pro-
vided;
❒Lower the car and remove the jack;
❒Using the wrench provided, tighten
the bolts in the sequence shown pre-
viously for the space-saver spare
wheel fig. 16;
❒Refit the snap-fitted wheel hub cap.
When you have finished
❒Stow the spare wheel C-fig. 11in the
space provided in the boot;
❒Insert the jack partially open in its con-
tainer B-fig. 11forcing it lightly to
prevent it from vibrating when trav-
elling;
❒Put the tools back into their places in
the container;
❒Stow the container complete with
tools on the spare wheel and secure
everything with the clamping device
A-fig. 11;
❒Correctly re-position the stiff cover.
Modifications or repairs to
the electrical system carried
out incorrectly and without bearing
the features of the system in mind can
cause malfunctions with the risk of
fire.
WARNING
Halogen bulbs contain pres-
surised gas which, if broken,
may cause small fragments of glass to
be projected outwards.
WARNING
Only touch the metal part
when handling halogen bulbs.
If the transparent bulb is
touched it reduces the intesi-
ty of the light emitted and can also re-
duce the life of the bulb. If you touch
the bulb accidentally, rub it with a
cloth moistened with alcohol and leave
it to dry.
IMPORTANT The headlight inner surface
may be lightly misted over: this is not a
fault but a natural fact due to low tem-
perature and the level of air humidity. It
will disappear as soon the headlights are
turned on. The presence of drops inside
the headlights means water infiltration,
therefore contact Fiat Dealership.
133-160 idea GB 1 ed 10-07-2008 8:30 Pagina 144

159
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
TOWING THE CAR
The car is delivered with two tow rings:
the short tow ring shall be fitted at the
front and the long one at the back.
Side figures show how rear (long) ring was
arranged, within spare wheel fig. 44 and
in the container of kit Fix & Go automat-
ic, respectively fig. 45.
HOW TO REMOVE TOW HITCH
CAPS
To avoid damaging the cap A-fig. 46, pro-
ceed as follows:
❒take the screwdriver provided in the
tool kit;
fig. 46F0H0250m
fig. 47F0H0251m
❒insert the screwdriver in the cap slot
B;
❒put the hand thumb on the cap to pre-
vent damaging it fig. 47;
fig. 44F0H0342m
fig. 45F0H0361m
❒remove the cap (without turning it)
making a movement perpendicular to
the supporting surface fig. 47.
133-160 idea GB 1 ed 10-07-2008 8:30 Pagina 159

165
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
ANNUAL INSPECTION
SCHEDULE
For cars with an annual mileage of below
20,000 km (for example about 15,000 km)
the following yearly inspection programme
is provided:
❒check tyre conditions/wear and adjust
pressure if required (including the
spare wheel);
❒check lighting system operation (head-
lights, direction indicators, hazard
lights, boot lights, passenger compart-
ment lights, warning lights, etc.);
❒check windscreen/washer (nozzles/
and blade position regulation)
❒check front disk brake pad conditions
and wear;
❒sight inspect the conditions of: engine,
gearbox, transmission, pipes and hoses
(exhaust - fuel - brakes), rubber parts
(boots, sleeves, bushes, etc;
❒check for bonnet and boot lock clean-
ness, lever cleanness and lubrication;
❒check battery charge;
❒visual check on various drive belt con-
ditions;
❒top up fluid levels (engine coolant,
brakes, windscreen washer, battery,
etc.);
❒change engine oil;
❒change engine oil filter;
❒replace pollen filter (where provided).
ADDITIONAL CHECKS
Every 1,000 km or before long journeys,
check and top up if required:
❒engine coolant fluid level;
❒brake fluid level;
❒windscreen washer fluid level;
❒tyre pressure and conditions.
Every 3,000 km check and top up if re-
quired: engine oil level.
You are recommended to use FL Selenia
products, designed and produced specifi-
cally for Fiat cars (see table “Capacities”
in section “Technical specifications”).
161-180 idea GB 1 ed 10-07-2008 8:30 Pagina 165

175
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
WHEELS AND TYRES
Check the pressure of each tyre, includ-
ing the spare, every two weeks and before
long journeys. The pressure should be
checked with the tyre rested and cold.
For the correct tyre inflation pressure, see
“Wheels” in “Technical specifications”
section.
Incorrect pressure causes abnormal tyre
wear fig. 13:
A: normal pressure: tread evenly worn.
B: low pressure: tread particularly worn
at the edges.
C: high pressure: tread particularly worn
in the centre.
Tyres must be replaced when the tread
wears down to 1.6 mm. In any case, com-
ply with the laws in the country where the
car is being driven.
IMPORTANT NOTES
❒As far as possible, avoid sharp brak-
ing and screech starts, etc. Be careful
not to hit the kerb, potholes or oth-
er obstacles hard. Driving for long
stretches over bumpy roads can dam-
age the tyres.
❒Periodically check that the tyres have
no cuts in the side wall, abnormal
swelling or irregular tyre wear. If any
of these occur, have the car seen to at
a Fiat Dealership.
❒Avoid overloading the vehicle when
travelling: this may cause serious dam-
age to the wheels and tyres.
❒If a tyre is punctured, stop immediately
and change it to avoid damage to the
tyre, the rim, suspensions and steer-
ing system.
❒Tyres age even if they are not used
much. Cracks in the tread rubber are
a sign of ageing. In any case, if the tyres
have been on the car for over 6 years,
they should be checked by specialised
personnel, to see if they can still be
used. Also remember to check the
spare wheel.
fig. 13F0H0216m
Remember that road holding
depends also on the correct
tyre inflating pressure.
If the pressure is too low the tyre
overheats and this can cause it seri-
ous damage.
WARNING
Do not cross switch the
tyres, moving them from the
right of the car to the left and vice
versa.
Never submit alloy rims to repainting
treatments requiring to use tempera-
tures exceeding 150°C since the me-
chanical properties of the wheels
could be impaired.
WARNING
❒In the case of replacement, always fit
new tyres, avoiding those of dubious
origin;
❒If a tyre is changed, also change the in-
flation valve;
❒To allow even wear between the front
and rear tyres, it is advisable to change
them over every 10-15 thousand kilo-
metres, keeping them on the same
side of the car so as to not reverse the
direction of rotation.
161-180 idea GB 1 ed 10-07-2008 8:30 Pagina 175

189
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
fig. 5F0H0229m
WHEELS
RIMS AND TYRES
Pressed steel or alloy rims. Tubeless tyres
with radial carcass. The homologated tyres
are listed in the Log book.
IMPORTANT In the event of discrepan-
cies between the information provided on
this “Owner handbook” and the “Log
book”, consider the specifications shown
in the log book only.
Attaining to the prescribed size, to ensure
safety of the car in movement, it must be
fitted with tyres of the same make and
type on all wheels.
IMPORTANT Do not use inner tubes
with Tubeless tyres.UNDERSTANDING TYRE
MARKING
Example: 185/65 R 14 86 T
185 = Nominal width (S, distance
between sidewalls in mm).
65 = Percentage height/width ratio
(H/ S).
R = Radial tyre.
14 = Rim diameter in inches (Ø).
86 = Load rating.
T = Maximum speed rating. SPACE-SAVER SPARE WHEEL
Pressed steel rim. Tubeless tyre.
WHEEL GEOMETRY
Front wheel toe-in measured from rim to
rim: 0 ±1 mm.
The values refer to the car in running or-
der.
181-199 idea GB 1 ed 10-07-2008 8:31 Pagina 189