brake FIAT MULTIPLA 2006 1.G Owner's Manual

170
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
Please note:
❒the jack weight is 3.5 kg
❒the jack requires no adjustment
❒the jack cannot be repaired and in the event of a fault it must be
replaced by another original one
❒no tool other than its cranking device may be fitted on the jack.
To change a wheel proceed as follows:
❒Stop the car is a position that is not dangerous for oncoming traffic
where you can change the wheel safely. The ground should be flat and
adequately firm. At night choose a lit area;
❒Turn the engine off and pull up the handbrake;
❒Engage first gear or reverse;
❒Take out tools, jack and space-saver spare wheel;
❒Tools are located in a compartment on the left side of the boot. To
have access, turn the clasp (A) anticlockwise and take off cover (B);
they are secured by a strap (C) that has to be released to remove
them;
❒Label (D) on the internal side of the cover shows how to remove and
refit tools in the compartment;
❒The space-saver spare wheel is located under the body at the back of
the car;
F0E0618m
F0E0122m

180
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
INFLATING PROCEDURE
FOE0712m
FOE0713m
FOE0715mFOE0714m
WARNINGPut on the protection gloves provided
together with quick tyre repair kit.
❒Pull up the handbrake. Loosen tyre inflation valve cap, take the filler
hose (A) out and screw the ring nut (B) on the tyre valve;
❒make sure the compressor switch (D) is set at 0 (off), then start the
engine and fit plug (E) into the nearest outlet and turn on the
compressor by setting switch (D) to I (on). Inflate the tyre to the
pressure value specified in paragraph “Inflation pressure” in section
“Technical Specifications”. Check tyre pressure on gauge (F) with
compressor off to obtain precise reading;
❒if after 5 minutes it is still impossible to reach at least 1.5 bar,
disengage compressor from valve and outlet, then move the car forth
for approx. ten metres in order to distribute the sealing fluid inside the
tyre evenly, then repeat the inflation operation;

181
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
❒if also in this case, after 5 minutes from turning the
compressor on it is still impossible to reach at least
1.8 bar, do not start driving since the tyre is
excessively damaged and the quick tyre repair kit
cannot guarantee suitable sealing, contact Fiat
Dealership;
❒if the proper tyre pressure has been reached (see
paragraph “Inflation pressure” in section “Technical
Specifications”, start driving immediately;❒after driving for about 10 minutes stop and check
again the tyre pressure; pull up the handbrake;
WARNING
WARNING
WARNING
Apply the sticker in a visible position
for the driver to indicate that the tyre
has been treated with the quick tyre
repair kit. Drive carefully especially
when cornering. Do not exceed 80
km/h. Avoid heavy braking and
accelerating.
It is of vital importance to
communicate that the tyre has been
repaired using the quick tyre repair kit.
Hand the instruction brochure to the
personnel charged with treating the
tyre repaired with the kit. If the pressure falls below 1.8 bars, do
not drive any further: the quick tyre
repair kit Fix & Go automatic cannot
guarantee proper hold
because the tyre
is too much damaged.
Contact Fiat
Dealership.
❒if pressure read is at least 1.8 bar, restore proper
pressure (with engine running and handbrake on)
and restart;
❒drive with the utmost care to the nearest Fiat
Dealership.

185
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
12V-5W
12V-55W
12V-55W
12V-21W
12V-5W
12V-55W
12V-21/5W
12V-21W
12V-21/5W
12V-21W
12V-2,3W
12V-5W
12V-10W
12V-10W (*)
12V-1W
12V-5W W5W
H7
H1
P21W
WY5W
H1
R5W
P21W
P21W
P21W
–
W5W
C10W
C5W
–
W5W A
D
E
B
A
E
B
B
B
B
A
A
C
C
C
A
Bulbs Ref. figure Type Power
Front side lights
Dipped beams
Main beams
Front direction indicators
Side direction indicators
Front fog lights
(where provided)
Rear light cluster
- side/taillights
- reversing light
- fog light
- direction indicators
Third brake light
Number plate light
Front ceiling light
Rear ceiling light
Vanity mirror light
Boot light
(*) 12V-5W in versions with sunroof.

190
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
REAR LIGHT CLUSTER
To change the bulb, proceed as follows:
❒from inside the boot release and remove cover (A) by turning the
retaining knob (B), then remove pin (C) to reach the third nut;
❒loosen the two visible nuts (D) and the third one that can be reached
through hole (E); remove the light unit;
❒remove connectors, loosen the three screws (F) and open the light
holder unit;
❒remove the burnt out bulb, by pressing it slightly and turning it
counterclockwise.
The same operations stand valid for the left light unit.
Bulbs are the following:
G - 12V-5/21W, two-light, for taillights and brake lights
H - 12V-21W for reversing light
I - 12V-21W for direction indicators
L - 12V-21W for rear fog lights
After replacing, refit the headlight by reversing the above operations.
F0E0673m
F0E0674m
F0E0675m

191
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
THIRD BRAKE LIGHTS
To replace 12V-3W bulbs:
❒with the tailgate open, undo the four fastening screws under the caps
(shown by the arrows) and remove the panel;
❒take out connection (A);
❒undo the four screws securing the light unit and remove the cover
(B);
❒remove the bulbs (C) to be replaced from their seats.
After replacing the bulb, refit the two halves of the light unit then secure
the latter to the covering panel after reconnecting the electric
connection; refit the panel to the tailgate.
NUMBER PLATE LIGHTS
To replace the 12V-5W bulb:
❒using a screwdriver in the direction of the arrow, compress catch (F)
and take out the number plate light unit;
❒remove bulb holder and lens (D);
❒take out the bulb holder turning it slightly and replace the bulb (E).
F0E0254m
F0E0146m
F0E0676m

197
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
1
2
2
3
3
3
4
5
6
6
6
6
6
6
6
7
7
7
7
8
8
8
8
9
9
10 10
10
10
20
20
20
10
30
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
15
15
20
Fuses inside the car Ampere Fuse no.
Right-hand main beam
Left-hand main beam
Main beam warning light
Rear fog lights
Rear fog lights warning light
Side/taillight power
Left-hand dipped beam
Car interior fan
Right-hand number plate light
Right-hand front sidelight
Cigar lighter light
Ashtray light
Side/taillight warning light
Sound system light
Left-hand taillight
Left-hand number plate light
Left-hand front sidelight
Right-hand taillight
Heating system lighting
Right-hand dipped beam
Brake fluid warning light
Headlight beam adjuster
Headlight washer relay coil
Cigar lighter
Conditioner compressor
Headlight washer

198
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
10
10
11
12
12
12
12
12
12
12
12
12
12
12
13
13
13
13
13
13
13
13
13
13
13 20
20
20
10
10
10
10
10
10
10
10
10
10
10
15
15
15
15
15
15
15
15
15
15
15Windscreen wiper
Rear window wiper
Horn
+ 30 instrument panel
+ 30 front ceiling light
+ 30 EOBD Fiat tester
+ 30 rear ceiling light
+ 30 sound system
+ 30 connect-nav
+ 30 navigator
+ 30 clock
+ 30 sunroof
+ 30 webasto (additional heater)
+ 30 anti-theft control unit
Reversing light
Front direction indicators
Brake light
Third brake light
Rear direction indicators
Direction indicator warning light
Side direction indicators
Hazard light warning light
+ 15 cellular phone
+ 15 sound system
+ 15 connect-nav
Fuses inside the car Ampere Fuse no.

204
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
WARNINGDo not start the engine when towing the vehicle.
Before starting to tow, turn the ignition key to MAR and then to STOP. Do not
remove the key. If the key is removed, the steering lock engages automatically
resulting in the impossibility to steer the wheels. WARNING
WARNINGWhen towing, remember that without the help of the servobrake and power
steering, a greater effort is required on the pedal and steering wheel. Do not use
flexible cables for towing and avoid jerks. During towing operations make sure that
fastening the joint to the car does not damage the components in contact with it.
When towing the car, you must comply with the specific traffic regulations
regarding the tow ring and how to tow on the road.

207
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
CAR
MAINTENANCE
SERVICE SCHEDULE
20 40 60 80 100 120 140 160 180
●●●●● ●●●●
●●●●● ●●●●
●●●●● ●●●●
●●●●● ●●●●
●●●●● ●●●●
●●●
●●●
●●●●● ●●●●
●●
●● ●
●●
●● ● ●
●●●●● ●●●●
Thousands of km
Check tyre conditions/wear and adjust pressure if required
Check lighting system operation (headlights, direction indicators,
hazard lights, boot lights, passenger compartment lights,
glovebox lights, warning lights, etc.)
Check windscreen wiper/washer operation, adjust nozzles
Check windscreen/rear window blade position/wear
Check front disk brake pad conditions and wear
and wear indicator operation
Check rear drum brake linings conditions and wear
(where provided)
Check rear disk brake pad conditions and wear
Sight inspect the conditions of: bodywork, underbody
protection, pipes and hoses (exhaust - fuel - brakes), rubber
parts (boots, sleeves, bushes, etc.) fuel and brake system hoses
Check tension and adjust accessory drive belts (excluding
engines with automatic belt tighteners)
Sight inspect accessory drive belt conditions (petrol versions)
Sight inspect accessory drive belt conditions (diesel versions)
Check clutch pedal height or stroke and adjust if necessary
Check cleanness of locks, bonnet and boot and lever cleanness
and lubrication