pressure FIAT PANDA 2007 169 / 2.G User Guide

IMPORTANT Do not use inner tubes
with tubeless tyres. Check the inflation
pressure of the tyres and the spare wheel
regularly.
IMPORTANT You will need to change the
set of bolts if you want to change the type
of wheels fitted (alloy rims instead of steel
rims, and vice versa). You will have to
change the entire set of fastening bolts
with another set of suitably sized bolts and
adopt a specific spare wheel having differ-
ent building characteristics.
You should keep the bolts and spare
wheel in case you decide to use the orig-
inal type of wheel later on. ❒fasten the three other bolts with the
wrench provided;
❒lower the car and remove the jack;
❒fasten bolts completely, working in a
criss-cross fashion as shown in fig. 10.
fig. 10F0G0696m
131
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
When you have finished
❒arrange the space-saver spare wheel D-
fig. 3in the specific compartment in the
boot;
❒insert the partially open jack into the
container Cand force it slightly into its
seat so that it does not vibrate when
the car is moving;
❒ put the tools back into their places in
the container;
❒stow the container complete with tools
on the spare wheel and secure every-
thing with the clamping device B;
❒correctly reposition the boot stiff cov-
er.
123-154 Panda New GB 21-06-2007 13:51 Pagina 131

134
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
fig. 4F0G0672mfig. 6F0G0698m
fig. 5F0G0673m
❒check that the compressor switch D-
fig. 4is set at 0 (off), start the engine,
fit plug E-fig. 5into the 12V outlet lo-
cated on the central console and then
turn the compressor on setting the
switch D-fig. 4in position I(on). Inflate
the tyre at the pressure value specified
in paragraph “Inflation pressure” in sec-
tion “Technical Specifications” Check tyre pressure on gauge F-
fig. 4with compressor off to obtain
precise reading;
❒if after 5 minutes it is still impossible
to reach at least 1.5 bar, disengage com-
pressor from valve and current outlet,
then move the car forth for approx. ten
metres in order to distribute the seal-
ing fluid inside the tyre evenly, then re-
peat the inflation operation;
❒If after this operation it is still impossi-
ble after 5 minutes to reach at least 1.8
bar, do not start driving since the tyre
is excessively damaged and the quick
tyre repair kit cannot guarantee suit-
able sealing, contact Fiat Dealership;
❒if reaching the tyre pressure specified
in paragraph “Inflation pressure” in sec-
tion “Technical Specifications”, start
driving immediately;
❒after driving for about 10 minutes stop
and check again the tyre pressure; pull
up the handbrake;
Apply the sticker in a visible
position for the driver to in-
dicate that the tyre has been treat-
ed with the quick tyre repair kit. Dri-
ve carefully especially when corner-
ing. Do not exceed 80 km/h. Avoid
heavy braking and accelerating.
WARNING
If the pressure falls below 1.8
bars, do not drive any fur-
ther: the quick tyre repair kit Fix & Go
automatic cannot guarantee proper
hold because the tyre is too much
damaged. Contact Fiat Dealership.
WARNING
123-154 Panda New GB 21-06-2007 13:51 Pagina 134

135
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
❒if at least 1.8 bar pressure is read, re-
store proper pressure (with engine
running and handbrake on) and restart;
❒drive with the utmost care to the near-
est Fiat Dealership.
It is of vital importance to
communicate that the tyre
has been repaired using the quick tyre
repair kit. Hand the instruction
brochure to the personnel charged
with treating the tyre repaired with
the kit.
WARNINGfig. 7F0G0699mfig. 8F0G0676m
FOR CHECKING AND
RESTORING PRESSURE ONLY
The compressor can be also used just for
restoring pressure. Release cylinder con-
nection A-fig. 8and connect it directly to
the tyre valve fig. 7; in this way the cylin-
der is not connected to compressor and
the sealing fluid will not flow into the tyre. CYLINDER REPLACEMENT
PROCEDURE
To replace the cylinder proceed as fol-
lows:
❒disconnect connection A-fig. 8;
❒turn counter-clockwise the cylinder to
replace and raise it;
❒fit the new cylinder and turn it clock-
wise;
❒connect connection Ato the cylinder
and fit the transparent tube Binto the
proper space.
123-154 Panda New GB 21-06-2007 13:51 Pagina 135

139
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
To change the direction indicator bulb,
proceed as follows:
❒release clip A-fig. 21and remove cap
B;
❒turn the bulb-holder D-fig. 22and re-
move it (it is pressure-fitted);
IF AN EXTERIOR LIGHT
BURNS OUT
For the type of bulb and power rating, see
“When needing to change a bulb”.
fig. 21F0G0089mfig. 22F0G0090m
fig. 23F0G0091m
FRONT LIGHT UNITS
To change the bulb, proceed as follows:
❒release clip A-fig. 21 and remove cap
B;
❒turn the bulb-holder C-fig. 22and re-
move it (it is pressure-fitted);
❒remove the burnt bulb E-fig. 23 and fit
the new bulb;
❒refit by reversing the above mentioned
operations.
123-154 Panda New GB 21-06-2007 13:51 Pagina 139

SIDE DIRECTION INDICATORS
To change the bulb, proceed as follows:
❒push the transparent cover A-fig. 27
towards car running direction (it is
pressure-fitted);
❒remove connector G-fig. 25;
❒release the bulb holder catch H;
❒remove the burnt bulb I-fig. 26and fit
the new bulb;
❒refit by reversing the above mentioned
operations.
fig. 25F0G0093mfig. 27F0G0095m
fig. 26F0G0094m
140
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
❒remove the burnt bulb F-fig. 24and fit
the new bulb;
❒refit by reversing the above mentioned
operations.
To replace the main/dipped beam light
bulb, proceed as follows:
❒release clip A-fig. 21and remove cap
B;
fig. 24F0G0092m
123-154 Panda New GB 21-06-2007 13:51 Pagina 140

141
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
❒remove the transparent cover A-fig.
28from bulb holder (it is pressure-fit-
ted);
❒remove the bulb Band replace it;
❒ refit the lens.
❒loosen cover C-fig. 30and remove the
connector D;
❒release clip E-fig. 31and remove the
bulb F;
❒refit by reversing the above mentioned
operations. FRONT FOG LIGHTS
(where provided)
To change the halogen bulb, proceed as
follows:
❒slacken the two fog light fastening
screws A-fig. 29on the bumper;
❒slacken the two fog light fastening
screws Bunder the bumper;
❒remove the protection including the fog
light and remove the connector;
fig. 29F0G0227mfig. 28F0G0604mfig. 30
TOPOFFON
F0G0228m
fig. 31F0G0229m
123-154 Panda New GB 21-06-2007 13:51 Pagina 141

143
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
Number plate light
To change the bulb, proceed as follows:
❒use a screwdriver to remove the re-
taining spring as shown in fig. 35;
fig. 35F0G0099mfig. 36F0G0100m
THIRD STOP LIGHT
To change the bulb, proceed as follows:
❒slacken the two screws A-fig. 37and
remove the whole cover;
❒disconnect connector B-fig. 38and re-
move the light unit;
fig. 37F0G0101m
fig. 38F0G0210m
❒remove the transparent A-fig. 36and
the bulb Bfrom the bulb holder;
❒change the 12V-5W bulb pressure-fit-
ted in the bulb holder;
❒ refit the lens.
123-154 Panda New GB 21-06-2007 13:51 Pagina 143

144
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
❒release clip C-fig. 39and remove the
light unit from the lens unit;❒replace the pressure-fitted burnt out
bulb D;
❒refit by reversing the above mentioned
operations.
fig. 39F0G0211m
IF AN INTERIOR LIGHT
BURNS OUT
For the type of bulb and power rating, see
“When needing to change a bulb”.
CEILING LIGHT
To change the bulb, proceed as follows:
❒insert the screwdriver supplied with the
car in the point shown by the arrow
and remove the ceiling light A-fig. 40;
123-154 Panda New GB 21-06-2007 13:51 Pagina 144

146
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
IF A FUSE BLOWS
GENERAL fig. 45
The fuse is a protective device for the
electric system: it comes into action (i.e.
it cuts off) mainly due to a fault or im-
proper action on the system.
When a device does not work, check the
efficiency of its fuse: the conductor ele-
ment Amust be intact. If not, replace the
fuse with one of the same amp rating
(same colour).
Bundamaged fuse.
Cfuse with damaged filament.
To facilitate fuse replacement, use the pli-
ers Dhooked to the fusebox on the in-
strument panel left-hand side.
Refer to the tables on the following pages
to identify the protection fuse.
❒open the bulb cover B-fig. 44and re-
place the pressure-fitted bulb C;
❒refit the cover Bon the transparent;
❒refit correctly the light pressing one
side and then the other until the lock-
ing click is heard.
fig. 44F0G0103mfig. 45F0G0087m
Never replace a fuse with
metal wires or anything else.
Never replace a fuse with
another with a higher amp
rating; DANGER OF FIRE.
WARNING
If a general fuse (MEGA-
FUSE, MIDI-FUSE, MAXI-
FUSE) cuts in, do not attempt any re-
pair and contact a Fiat Dealership.
WARNING
If a fuse blows again, contact
a Fiat Dealership.
WARNING
Before replacing a fuse,
make sure the ignition key
has been removed and that all the
other services are switched off and/or
disengaged.
WARNING
123-154 Panda New GB 21-06-2007 13:51 Pagina 146

149
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
5
7.5
7.5
10
7.5
15
15
7.5
7.5
7.5
7.5
5
5
15
–
–
7.5
7.5
7.5
20
10
10
10
10 F31
F35
F35
F37
F41
F45
F46
F49
F49
F49
F50
F51
F51
F54
FA
FB
F12
F13
F13
F38
F39
F39
F39
F39
FUSE SUMMARY TABLE
Passenger’s compartment fusebox - fig. 47FUSE AMPERE
Reversing light
+15 radio
Central dashboard
+15 stop light
Door mirrors defroster
Heated seats (pre-arrangements)
Electric sunroof
Automatic climate control system
Tyre pressure
Sensor for water presence in the gas oil filter
+15 air bag control unit
+15 Body-computer control unit
+15 instrument panel
Subwoofer
Free
Free
Right dipped beam headlight
Left dipped beam headlight
To adjust the headlight slant
+ 30 door locking device
EOBD diagnosis socket
Radio
Automatic climate control system
Tyre pressure
123-154 Panda New GB 21-06-2007 13:51 Pagina 149