wheel bolts FIAT PANDA 2007 169 / 2.G Owners Manual
[x] Cancel search | Manufacturer: FIAT, Model Year: 2007, Model line: PANDA, Model: FIAT PANDA 2007 169 / 2.GPages: 206, PDF Size: 3.49 MB
Page 127 of 206
BUMP STARTING
Never bump start the engine (by pushing,
towing or coasting downhill).
This could cause fuel to flow into the cat-
alytic converter and damage it beyond re-
pair.
IMPORTANT Remember that the servo-
brake and electrical power steering sys-
tem (where provided) are not operating
until the engine is started, a greater effort
will therefore be required to press the
brake pedal or turn the steering wheel.
126
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
The space-saver spare wheel
(where provided) is specific
to your car, do not use it on other
models, or use the spare wheel of oth-
er models on your car. The space-
saver spare wheel shall only be used
in an emergency. It shall only be used
for the distance necessary to reach a
service point and the car speed shall
not exceed 80 km/h. The spare wheel
has an orange sticker that summaris-
es the main cautions for use and lim-
itations. The sticker should never be
removed or covered. Never fit a wheel
cap on a space-saver spare wheel.
The sticker gives the following infor-
mation in four languages: Caution!
For temporary use only! 80 km/h max!
Replace by normal wheel as soon as
possible. Do not cover this label in
use.
If you change the type of wheel (al-
loy rims instead of steel rims) you will
have to change the entire set of fas-
tening bolts with another set of suit-
ably sized bolts.
WARNINGIF A TYRE
IS PUNCTURED
GENERAL INSTRUCTIONS
The car can be delivered (upon re-
quest/where provided) with standard
spare wheel or space saver spare wheel;
see changing instructions on the following
paragraphs.
Wheel changing and correct use of the
jack and space-saver spare wheel call for
some precautions as listed below.
123-154 Panda New GB 21-06-2007 13:51 Pagina 126
Page 128 of 206
127
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
Alert other drivers that the
car is stationary in compli-
ance with local regulations: hazard
warning lights, warning triangle, etc.
Any passengers on board should leave
the car, especially if it is heavily laden.
Passengers should stay away from on-
coming traffic while the wheel is be-
ing changed. If parked on a slope or
rough surface, chock the wheels with
wedges or other suitable devices.
WARNING
When driving with a space-
saver spare wheel fitted, the
driving performance of the car
changes. Avoid accelerating or brak-
ing sharply, abrupt turns of fast cor-
nerings. The life of a spare wheel is
approx. 3000 km, after this distance
it should be replaced with another of
the same type. Never attempt to fit
a conventional tyre on a rim designed
for use as a space-saver spare wheel.
Have the punctured wheel repaired
and refitted as soon as possible. Two
or more space-saver spare wheels
should never be used together. Do not
grease the threads of bolts before in-
stalling them: they might slip out.
WARNING
The jack shall only be used
for changing wheels on the
car with which it is provided or on
cars of the same model. It must not
be used for other purposes such as for
instance raising cars of other models.
In no case should it be used for repairs
under the car. Incorrect positioning
of the jack may cause the jacked car
to fall. Do not use the jack for high-
er capacities than stated on its label.
Snow chains cannot be fitted to the
space-saver spare wheel. So, if a front
(drive) wheel is punctured and chains
are needed, a rear wheel should be
fitted to the front of the car and the
spare wheel should be fitted to the
rear. This way with two normal dri-
ve wheels, snow chains can be fitted
to them to solve an emergency.
WARNING
Fasten the wheel cap cor-
rectly to prevent the wheel
from coming free in motion. Never
tamper with the inflation valve. Nev-
er place tools between the rim and
tyre. Check and restore, if required,
the pressure of tyres and spare wheel
to the values given in section “Tech-
nical specifications”.
WARNING
Please note:
❒ the jack weight is 1,76 kg;
❒the jack requires no adjustment;
❒the jack cannot be repaired and in the
event of a fault it must be replaced by
another original one;
❒no tool other than its cranking device
may be fitted on the jack.
123-154 Panda New GB 21-06-2007 13:51 Pagina 127
Page 129 of 206
❒loosen the bolts on the wheel to be re-
placed with the tool E-fig. 4provided;
❒turn handle to partially open the jack;
❒loosen the clamping device B-
fig. 3;
❒take out the tool container Cand take
it near the wheel to be changed;
❒take the space saver spare wheel D;
❒to remove the wheel cap secured by
spring, use the screwdriver provided
levering on the three notches present
on the outer circumference;
fig. 4F0G0695m
128
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCYfig. 3F0G0078m
To change a wheel proceed as follows:
❒Stop the car in a position that is not
dangerous for oncoming traffic where
you can change the wheel safely. The
ground should be flat and adequately
firm;
❒ turn the engine off and pull up the hand-
brake;
❒ engage first gear or reverse;
❒lift the luggage compartment mat A-
fig. 2;
fig. 2F0G0171m
123-154 Panda New GB 21-06-2007 13:51 Pagina 128
Page 130 of 206
❒fit the handle Hto operate the jack de-
vice Iand raise the car until the wheel
is a few centimetres from the ground.
When turning the jack handle make
sure that it can be used easily and take
care not to scrape your hand against
the ground. The moving parts of the
jack (screw and joints) may also cause
injury if touched. Clean off any grease;
❒remove the wheel cap (where provid-
ed) after loosening the three fastening
bolts then, loosen the fourth bolt L-
fig. 6and remove the wheel;
❒make sure the contact surfaces be-
tween spare wheel and hub are clean
so that the fastening bolts will not come
loose;
fig. 6F0G0233m
129
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
❒position the jack near the wheel to be
repaired at the reference point
Oon
the side member;
❒
extend the jack until groove F-fig. 5on
the jack fits correctly into ridge Gun-
derneath the side member;
❒alert other passengers that the car is
about to be raised; all persons should
be kept away from the car until it has
been lowered;
fig. 5F0G0173m
123-154 Panda New GB 21-06-2007 13:51 Pagina 129
Page 131 of 206
❒fasten bolts completely, working in a
criss-cross fashion as shown in fig. 8.
REFITTING THE STANDARD
WHEEL
❒Following the above procedure, raise
the car and remove the space saver
wheel;
❒make sure the contact surfaces be-
tween wheel and hub are clean so that
the fastening bolts will not come loose;
❒fit the standard wheel by inserting the
first bolt L-fig. 9in the hole next to the
inflation valve;
❒fit the wheel cap making the symbol Ccoincide with the inflation valve and the
bolt previously fastened to the hole M-
fig. 9/a
;
❒fit the spare wheel making pin N-fig.
7coincide with one of the wheel holes
O;
❒fasten the four fastening bolts;
❒turn the jack handle to lower the car
and remove the jack;
fig. 7F0G0204mfig. 8F0G0206m
fig. 9/aF0G0603m
130
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
fig. 9F0G0233m
123-154 Panda New GB 21-06-2007 13:51 Pagina 130
Page 132 of 206
IMPORTANT Do not use inner tubes
with tubeless tyres. Check the inflation
pressure of the tyres and the spare wheel
regularly.
IMPORTANT You will need to change the
set of bolts if you want to change the type
of wheels fitted (alloy rims instead of steel
rims, and vice versa). You will have to
change the entire set of fastening bolts
with another set of suitably sized bolts and
adopt a specific spare wheel having differ-
ent building characteristics.
You should keep the bolts and spare
wheel in case you decide to use the orig-
inal type of wheel later on. ❒fasten the three other bolts with the
wrench provided;
❒lower the car and remove the jack;
❒fasten bolts completely, working in a
criss-cross fashion as shown in fig. 10.
fig. 10F0G0696m
131
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
When you have finished
❒arrange the space-saver spare wheel D-
fig. 3in the specific compartment in the
boot;
❒insert the partially open jack into the
container Cand force it slightly into its
seat so that it does not vibrate when
the car is moving;
❒ put the tools back into their places in
the container;
❒stow the container complete with tools
on the spare wheel and secure every-
thing with the clamping device B;
❒correctly reposition the boot stiff cov-
er.
123-154 Panda New GB 21-06-2007 13:51 Pagina 131