fully FIAT PUNTO EVO 2010 1.G Owner's Guide

228
F0U0289mfig. 211
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Remember that the car’s road holding de-
pends on correct tyre pressures
WARNING
If the pressure is too low, the tyre will over-
heat and could be seriously damaged.
WARNING
Avoid switching the tyres from the right
side of the vehicle to the left side and vice
versa.
Do not re-spray alloy wheel rims at temperatures
higher than 150°C. The mechanical characteris-
tics of the wheels may be compromised.
WARNING
❒check the tyres regularly for cuts on the sides, swelling
or irregular tread wear. Go to a Fiat Dealership if re-
quired;
❒avoid overloading the car when travelling: this may cause
serious damage to the wheels and tyres;
❒if a tyre is punctured, stop the vehicle immediately and
change it to avoid damage to the tyre, the rim, and the
suspension and steering systems;
❒a tyre will age even if it is not used much. Cracks in
the tread and on the sidewalls are a sign of ageing. In
any event, have the tyres checked by specialised per-
sonnel if they have been fitted for longer than 6 years.
Remember to check the spare wheel very carefully;
❒in case of replacement, always fit new tyres, avoiding
those with an unknown origin;
❒if a tyre is replaced, you should also change the inflation
valve;
❒to allow even wear between the front and rear tyres,
it is advisable to switch them every 10-15 thousand kilo-
metres, keeping them on the same side of the car so
as not to reverse the direction of rotation.
211-234 PUNTO FL EN 4ed 18-01-2010 12:28 Pagina 228

F0U0291mfig. 213
SPRAY NOZZLES
Windscreen washer fig. 214
If the jet is not coming out, firstly check that there is flu-
id in the reservoir (see “Checking levels” in this section).
Then check that the nozzle holes are not clogged; use
a needle to unblock them if necessary.
230
F0U0290mfig. 212
Replacing the windscreen wiper blades fig. 212
How to remove the blade:
❒lift the arm A off the windscreen;
❒turn blade B 90° around pin C, located at the end of the
wiper arm;
❒ remove the blade from the pin C.
How to insert the blade:
❒fit pin C into the hole located in the middle of the
blade B;
❒refit the arm with the blade on the windscreen.
Changing the rear window wiper blade fig. 213
Proceed as follows:
❒raise the cover A and remove the arm from the car,
slackening the nut B that fastens it to the pivot pin;
❒fit the new arm, positioning it correctly, and fully tight-
en the nut;
❒ lower the cover.
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
211-234 PUNTO FL EN 4ed 18-01-2010 12:28 Pagina 230

232
VEHICLE BODY AND UNDERBODY
WARRANTY
Your car is covered by warranty against perforation, due
to rust, of any original element of the structure or body-
work.
For the general terms of this warranty, refer to your War-
ranty Booklet.
ADVICE FOR PRESERVING THE BODYWORK
Paint
Paintwork does not only serve an aesthetic purpose, but
also protects the underlying sheet metal.
Touch up abrasions and scratches immediately to prevent
the formation of rust. Use only original paint products
for touch-ups (see “Bodywork paint identification plate”
in the “Technical specifications” section).
Normal care for paintwork consists of washing the car;
how often depends on the conditions and environment
where the car is used. For example, it is advisable to wash
the car more often in areas with high atmospheric pollu-
tion or if you are travelling on gritted roads.
To wash the car properly, proceed as follows:
❒if taking your car through an automatic car wash, re-
move the aerial from the roof;
❒wash the body using a low-pressure jet of water;
❒use a sponge to wipe a slightly soapy solution over the
bodywork, frequently rinsing the sponge;
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
❒rinse with plenty of water and dry with a jet of air or
a chamois leather.
Dry the less visible parts particularly carefully, such as the
door frames, bonnet and the headlight frames, where wa-
ter may stagnate more easily. It is a good idea to leave
the car in the open for a while after washing it to give time
for the water to evaporate.
Do not wash the car after it has been left in the sun or
with the bonnet hot: this may alter the shine of the paint-
work.
Exterior plastic parts must be cleaned in the same way as
the rest of the car.
Where possible, do not park under trees; the resinous
substances that fall off many species give the paint a dull
appearance and increase the possibility of triggering rust
processes.
IMPORTANT Bird droppings should be washed off im-
mediately and thoroughly as the acid they contain is par-
ticularly aggressive.
211-234 PUNTO FL EN 4ed 18-01-2010 12:28 Pagina 232

F0U0294mfig. 216
H Maximum authorised weight on rear axle.
I Engine type.
L Bodywork version code.
M Number for spare parts.
N Correct value of smoke coefficient (for diesel engines).
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
235
TECHNICAL SPECIFICATIONS
IDENTIFICATION DATA
We recommend taking note of the identification codes.
The following identification codes are printed and
shown on the plates:
❒Vehicle identification number (VIN) plate.
❒Chassis marking.
❒ Bodywork paint identification plate.
❒Engine marking.
VIN PLATE fig. 216
The plate can be found on the left side of the boot floor
and it bears the following identification data:
B Type-approval number.
C Vehicle type identification code.
D Chassis manufacturing serial number.
E Maximum authorised weight of vehicle fully laden.
F Maximum authorised weight of vehicle fully laden plus
trailer.
G Maximum authorised weight on front axle.
235-258 PUNTO FL EN 4ed 18-01-2010 12:28 Pagina 235

KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
255
ARRANGEMENTS FOR DEALING WITH THE VEHICLE AT THE END OF ITS LIFE
Fiat has been committed for many years to safeguarding the environment through the constant improvement of its production
processes and manufacturing products that are increasingly “eco-compatible”.
To give customers the best possible service in terms of respecting environmental laws and in response to European Directive
2000/53/EC governing vehicles at the end of their life, Fiat is offering its customers the opportunity of handing over their
vehicle* at the end of its life without incurring any additional costs.
The European Directive sets out that when the vehicle is handed over the last keeper or owner should not incur any expenses
as a result of it having a zero or negative market value.
In all European Union countries, until 1st January 2007, only vehicles registered after 1st July 2002 were collected free of
charge, while since 2007 collection has been free of charge irrespective of the year of registration as long as the vehicle
contains its basic components (in particular, the engine and bodywork) and has no additional waste.
To hand your vehicle over at the end of its life without extra cost, go to one of our Dealerships or Fiat-authorised collection
and scrapping centres.
These centres have been carefully chosen to offer high quality service for the collection, treatment and recycling of unused
vehicles with respect to the environment.
You can find further information on these collection and scrapping centres either from a Fiat or Fiat Commercial Vehicle
Dealership or by calling the freephone number 00800 3428 0000 or by going on the Fiat website.
235-258 PUNTO FL EN 4ed 18-01-2010 12:28 Pagina 255

The engine of your car is factory filled with Selenia.
Oil change? The experts recommend Selenia
This is an engine oil range which satisfies the most advanced
international specifications. Its superior technical characteristics
allowSelenia to guarantee the highest performance
and protection of your engine.
The Selenia range includes a number of technologically advanced products:
SELENIA K PURE ENERGY
Synthetic lubricant designed for latest generation, low
emission, petrol engines. Its specific formulation warrants
the utmost protection also for high performance
turbocharged engines with high thermal stress.
Its low ash content helps to maintain the total cleanliness
of modern catalysts.
SELENIA WR PURE ENERGY
Fully synthetic lubricant that can meet the requirements of
the latest diesel engines. Low ash content to protect the
particulate filter from the residual products of combustion.
High Fuel Economy System that allows
considerable fuel saving.
It reduces the danger of dirtying the turbine to ensure the
protection of increasingly high performance diesel
enginesSELENIA MULTIPOWER
Particularly ideal for the protection of new generation petrol
engines, very effective even in the most severe weather
conditions. It guarantees a reduction in fuel consumption
(Energy conserving) and it is also ideal for alternative
engines.
SELENIA SPORT
Fully synthetic lubricant capable of meeting the needs of
high performance engines.
Studied to protect the engine also in high thermal stress
conditions, it prevents deposits on the turbine to achieve
the utmost performance in total safety.
The range also includes Selenia StAR Pure Energy, Selenia
Racing, Selenia K, Selenia WR, Selenia 20K, Selenia 20K AR.
For further information on Selenia products visit the web site
www.flselenia.com.
235-258 PUNTO FL EN 4ed 18-01-2010 12:29 Pagina 257