clutch FIAT PUNTO EVO 2010 1.G Owners Manual
[x] Cancel search | Manufacturer: FIAT, Model Year: 2010, Model line: PUNTO EVO, Model: FIAT PUNTO EVO 2010 1.GPages: 270, PDF Size: 8.34 MB
Page 3 of 270
REFUELLING
Petrol engines: only refuel the car with unleaded
petrol with an octane rating (RON) of no less than 95
conforming to the European specification EN 228.
The use of petrol that does not conform to the above-
mentioned specification may cause the EOBD warning light
to switch on and the irregular operation of the engine.
Diesel engines: only refuel the car using diesel fuel that
conforms to European specification EN590.
STARTING THE ENGINE
Make sure that the handbrake is properly applied; place the
gear lever in neutral; fully depress the clutch pedal, with-
out pressing the accelerator, then turn the ignition key to
the MAR position and wait for the
Yand mwarning
lights to switch off (diesel versions); turn the ignition key to
the AVV position and release it as soon as the engine starts.
PARKING ON FLAMMABLE MATERIAL
The catalytic converter reaches high temperatures dur-
ing operation. Do not park the on grass, dry leaves, pine
needles or other flammable material: fire hazard.
RESPECTING THE ENVIRONMENT
The car is fitted with a system that carries out a con-
tinuous diagnosis of the emission-related components
in order to help protect the environment.ELECTRICAL ACCESSORIES
If, after buying the car, you decide to add electrical ac-
cessories (with the risk of gradually draining the bat-
tery), visit a Fiat Dealership. They can calculate the over-
all electrical requirement and check that the car’s elec-
trical system can support the required load.
CODE card
Keep this in a safe place, not in the car. You should have
the electronic code from the CODE card with you at
all times.
SCHEDULED SERVICING
Correct maintenance of the car is essential for ensuring it
stays in tip-top condition and safeguards its safety features,
its environmental friendliness and low running costs for
a long time to come.
THE OWNER’S HANDBOOK CONTAINS…
... information, tips and important warnings on the cor-
rect use and maintenance of your car over time as
well as safe driving tips. Pay special attention to the sym-
bols
"(personal safety) #(environmental protection)
!(the car’s wellbeing).
READ THIS CAREFULLY!
K
001-036 PUNTO FL EN 4ed 18-01-2010 12:21 Pagina 2
Page 67 of 270
❒move the stalk upwards (+) for at least one second, then
release it. The car speed is now memorised and you can
therefore come off the accelerator pedal.
If needed (when overtaking for instance), you can accel-
erate simply by pressing the accelerator pedal; when you
come off the pedal, the car will return to the speed mem-
orised previously.
RESTORING THE MEMORISED SPEED
If the device has been switched off, for example by press-
ing the brake or clutch pedal, the memorised speed can
be restored as follows:
❒accelerate gradually until reaching a speed approaching
the memorised speed;
❒engage the gear that was selected when you memorised
the speed;
❒press button RES B-fig. 52.
66
CRUISE CONTROL
(for versions/markets where provided)
This is an electronically controlled device which allows the
vehicle to be driven at a chosen speed above 30 km/h on
long stretches of dry, straight roads with few variations (e.g.
motorways), without having to press the accelerator ped-
al. It is therefore not recommended to use this device on
country roads with traffic. Do not use it in town.
ENGAGING THE DEVICE
Turn twist switch A-fig. 52 to ON.
The cruise control cannot be engaged in 1st or reverse
gear. It is advisable to engage it in 4th gear or higher.
When travelling downhill with the device engaged, the car
speed may slightly exceed the preset one.
When the device is activated, light
Ücomes on together
with the relevant message on the instrument panel (where
provided).
SETTING VEHICLE SPEED
Proceed as follows:
❒turn twist switch A-fig. 52 to ON and press the accel-
erator pedal until you reach the required speed;
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0047mfig. 52
037-081 PUNTO FL EN 4ed 18-01-2010 12:23 Pagina 66
Page 68 of 270
67
INCREASING THE MEMORISED SPEED
This can be done in two ways:
❒by pressing the accelerator and then memorising the
new speed reached;
or
❒moving the stalk upwards (+).
Each movement of the stalk will correspond to an increase
in speed of about 1 km/h, while keeping the stalk held up-
wards will continuously increase the speed.
REDUCING THE MEMORISED SPEED
This can be done in two ways:
❒by turning the device off and then storing a new speed;
or
❒by moving the stalk downwards (–) until reaching the
new speed which will be memorised automatically.
Each movement of the stalk will correspond to a reduc-
tion in speed of about 1 km/h, while keeping the stalk held
downwards will continuously reduce the speed.
DISENGAGING THE DEVICE
The device can be switched off by the driver in the fol-
lowing ways:
❒turning twist switch A to OFF;
❒switching off the engine;
❒pressing the brake pedal;
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
❒pressing the clutch pedal;
❒pressing the accelerator pedal; in this case, the system
is not really switched off but the request for accelera-
tion takes priority. The cruise control is, however, ac-
tive and you do not need to press button RES B-fig. 52
to restore the previous conditions when you have fin-
ished accelerating.
The device is automatically switched off in the following
cases:
❒if the ABS or ESP systems cut in;
❒if the car speed drops below the preset limit;
❒if there is a system failure.
While travelling with the device engaged, do not
put the gear lever into neutral.
WARNING
In case of malfunctioning or if the device fails,
turn twist switch A to OFF and contact a Fiat
Dealership.
WARNING
037-081 PUNTO FL EN 4ed 18-01-2010 12:23 Pagina 67
Page 116 of 270
115
F0U0200mfig. 118F0U0201mfig. 119
With Dualogic gearbox
(for versions/markets where provided)
The engine cuts out if the car stops with the brake pedal
pressed.
This condition can be maintained even if the brake pedal
is not pressed, if the gear lever is in position N.
NB: The engine can be stopped automatically only after
a speed of about 10 Km/h is reached, to prevent the en-
gine from being repeatedly stopped when driving at walk-
ing pace.
The engine being stopped is signalled by the warning light
fig. 118 on the instrument panel, depending on the con-
figuration.
Engine restarting mode
With normal transmission
Press the clutch pedal to allow the engine to be restarted.
START&STOP SYSTEM
(for versions/markets where provided)
FOREWORD
The Start&Stop device automatically stops the engine each
time the vehicle is stationary and starts it again when the
driver wants to move off.
This improves the efficiency of the vehicle by reducing fu-
el consumption, the emission of harmful gases and noise
pollution. The system is activated each time the car is
started.
OPERATING MODES
Engine cut-out mode
With manual transmission
With the vehicle stationary, the engine cuts out with the
gearbox in neutral and the clutch pedal released.
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
082-128 PUNTO FL EN 4ed 20-01-2010 15:06 Pagina 115
Page 118 of 270
117
F0U0203mfig. 121
SAFETY FUNCTIONS
In engine cut-out conditions through the Start&Stop sys-
tem, if the driver unfastens his/her seat belt and opens the
driver’s door or the passenger door, the engine can be
restarted only by using the key.
The driver is notified of this condition both by a buzzer
and through an information message on the display and
(for versions/markets where provided) by the warning light
fig. 121 on the instrument panel flashing.
ENERGY SAVING FUNCTION
(For versions/markets where provided)
If, after the engine has been automatically restarted, the
driver does not take any action for a period of about 3
minutes, the Start&Stop system will definitively stop the
engine to avoid fuel consumption. In these cases, the en-
gine can be restarted only by using the key.
NB: In any case, it is possible to keep the engine running
by deactivating the Start&Stop system. RESTARTING CONDITIONS
For reasons of comfort, limiting harmful emissions and safe-
ty purposes, the power unit can restart automatically with-
out any action on behalf of the driver if certain conditions
are met, including:
❒ battery not sufficiently charged;
❒ windscreen wipers working at maximum speed;
❒extreme braking system pressure, e.g. following the
brake pedal being pressed repeatedly;
❒ car moving around, for example when driving on hilly
roads;
❒stopping the engine through the Start&Stop system for
more than about three minutes.
❒automatic climate control system for establishing a com-
fortable temperature or enabling the MAX – DEF func-
tion.
With a gear engaged, the engine can be automatically
restarted only by fully depressing the clutch pedal. The dri-
ver is asked to perform this operation through a message
on the instrument panel and, where provided, by the warn-
ing light fig. 121 on the instrument panel flashing
NB: If the clutch is not pressed, when the three minutes
have elapsed since the engine was stopped, the engine can
be restarted only by using the key.
NB: In cases when the engine stops and this is not desired,
due for example to the clutch pedal being released sharply
with a gear engaged, if the Start&Stop system is activat-
ed, the engine can be restarted by fully depressing the
clutch pedal or by putting the gear lever into neutral.KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
082-128 PUNTO FL EN 4ed 20-01-2010 15:06 Pagina 117
Page 150 of 270
149
STARTING PROCEDURE FOR PETROL
VERSIONS
Proceed as follows:
❒ensure that the handbrake is on;
❒put the gear lever into neutral;
❒fully depress the clutch pedal without touching the ac-
celerator;
❒turn the ignition key to AVV and let it go the moment
the engine starts.
If the engine does not start at the first attempt, return
the ignition key to STOP before repeating the procedure.
STARTING THE ENGINE
The car is fitted with an electronic engine lock device: if
the engine fails to start, see the paragraph on “The Fiat
CODE system” in the “Dashboard and controls” section.
The engine may be noisier during the first few seconds of
operation, particularly after a long period of inactivity. This
is a feature of hydraulic tappets, the timing system cho-
sen to reduce the number of servicing interventions, and
effects neither functionality nor reliability.
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
STARTING AND DRIVING
It is dangerous to let the engine run in en-
closed spaces. The engine consumes oxy-
gen and produces carbon dioxide, carbon monox-
ide and other toxic gases.
WARNING
In the first period of use, we recommend
that you do not demand maximum perfor-
mance from the car (e.g. excessive accel-
eration, extended travel at maximum revs, heavy
braking etc.).
With the engine off, do not leave the
key in the ignition to prevent draining the
battery.
Remember that the brake booster and
power steering are not operational until
the engine has been started, therefore you need
to apply much more force than usual to the brake
pedal and steering wheel.
WARNING
149-160 PUNTO FL EN 4ed 20-01-2010 14:37 Pagina 149
Page 151 of 270
150
If, when the ignition key is at MAR, the instrument panel
warning light
Yremains on together with warning light
U, turn the key to STOP and then back to MAR; if the
warning light remains on, try with the other keys provid-
ed with the car.
IMPORTANT If the instrument panel warning light
Ystays on permanently, contact a Fiat Dealership immedi-
ately.
IMPORTANT Never leave the ignition key at MAR when
the engine is off.
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTSSTARTING PROCEDURE FOR DIESEL
VERSIONS
Proceed as follows:
❒ensure that the handbrake is on;
❒put the gear lever into neutral;
❒turn the ignition key to MAR: the warning lights mand
Yon the instrument panel will turn on;
❒wait for the warning lights Yand m to turn off. The
hotter the engine is, the quicker this will happen;
❒fully depress the clutch pedal without touching the ac-
celerator;
❒turn the ignition key to AVV as soon as warning light
m goes out. If you wait too long, you will lose the ben-
efit of the heating work done by the glow plugs. Release
the key as soon as the engine starts.If the engine does not start at the first attempt, return
the ignition key to STOP before repeating the procedure.
If, when the ignition key is at MAR, the instrument panel
warning light
Yremains on together with warning light
m, turn the key to STOP and then back to MAR; if the
warning lights remain on, try with the other keys provid-
ed with the car.
IMPORTANT If the instrument panel warning light
Ystays on permanently, contact a Fiat Dealership immedi-
ately.
IMPORTANT Never leave the ignition key at MAR when
the engine is off.
Warning light mwill blink for 60 seconds
after starting or during prolonged crank-
ing to indicate a fault with the glow plug
system. Use the car as normal if the engine starts,
but go to a Fiat Dealership as soon as possible.
149-160 PUNTO FL EN 4ed 20-01-2010 14:37 Pagina 150
Page 154 of 270
153
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0130mfig. 148
USING THE MANUAL GEARBOX
To engage the gears, depress the clutch pedal fully and shift
the gear lever into the required positions (the diagram is
shown on the gear knob fig. 148).
To engage 6
thgear (for versions/markets where provided),
push firmly to the right when operating the lever in or-
der to avoid selecting 4
thgear by mistake. The same ap-
plies to the shift from 6thto 5thgear.
IMPORTANT Reverse may be engaged only when the car
is at a standstill. With the engine running, wait for at least
2 seconds with the clutch pedal fully depressed before en-
gaging reverse to prevent damage to the gears and grating.
To engage reverse R from neutral with a six-speed gearbox,
proceed as follows: lift ring A under the knob and at the
same time move the gear lever to the left and then forwards
fig. 148
Depress the clutch pedal fully to change
gear correctly. Therefore, the floor area
under the pedals should be clear: ensure that any
rubber mats are flat and do not interfere with the
pedals.
WARNING
Do not drive with your hand resting on the
gear lever, because this pressure, even if
light, can wear out the inner components
of the gearbox over time.
IMPORTANT The clutch pedal should be used only for
changing gear. Do not drive with your foot resting on the
clutch pedal, however slightly. For versions/markets where
provided, the electronic clutch control can intervene if it
interprets the incorrect driving style as a fault.
149-160 PUNTO FL EN 4ed 20-01-2010 14:37 Pagina 153
Page 155 of 270
154
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
SAVING FUEL
Here are some suggestions which may help you to save fu-
el and reduce the amount of toxic emissions released in-
to the atmosphere.
GENERAL CONSIDERATIONS
Car maintenance
Have checks and adjustments carried out in accordance
with the “Scheduled Servicing Plan”.
Tyres
Check the tyre pressures at least once every 4 weeks: if
the pressure is too low, consumption levels increase as re-
sistance to rolling is higher.
Unnecessary loads
Do not travel with an overloaded boot. The weight of
the car (especially when driving in town) and its arrange-
ment greatly affect fuel consumption and stability.
Roof rack/ski rack
Remove the roof rack or ski rack from the roof after use.
These accessories decrease aerodynamic penetration and
have a negative effect on fuel consumption. It is better to
use a trailer to transport particularly bulky objects.Electrical devices
Use electrical devices only for the amount of time need-
ed. The heated rear window, auxiliary headlights, wind-
screen wipers and fan heater use up a considerable amount
of current, causing increased fuel consumption (up to
+25% in the urban cycle).
Air conditioning
Air conditioning leads to higher fuel consumption (on av-
erage up to +20%). If the temperature outside is not too
extreme, try and use the air vents.
Spoilers
The use of non-certified spoilers may adversely affect aero-
dynamics and fuel consumption.
DRIVING STYLE
Starting
Do not warm up the engine at low or high revs when the
vehicle is stationary; this causes the engine to warm up more
slowly, thereby increasing fuel consumption and emissions.
It is advisable to set off immediately and slowly, avoiding high
revs: this allows the engine to warm up more quickly.
Unnecessary actions
Avoid revving up when stationary at traffic lights or before
stopping the engine. The latter action, like double de-
clutching, is entirely unnecessary and causes increased fu-
el consumption and pollution.
149-160 PUNTO FL EN 4ed 20-01-2010 14:37 Pagina 154
Page 204 of 270
203
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
7.5
7.5
5
5
10
5
20
20
20
20
5
5
7.5 1
8
13
2
5
11
4
6
14
7
12
3
10
FUSE TABLE
Dashboard fuse box fig. 190
DEVICESFUSE AMPS
Right dipped beam headlight
Lift dipped beam headlight, headlamp alignment corrector
INT/A supply for switch coils on engine fuse box
and switch coils on body computer control unit
Front ceiling light, rear ceiling light, visor lights,
door marker lights, boot light, glove box light
Supply and battery for EOBD diagnostic plug, automatic climate
control system control unit, alarm, sound system, convergence control unit
INT supply for instrument panel, switch on brake pedal
(N.O. contact), third brake light
Door locking/unlocking motors, dead lock activation motors, boot
unlocking motor
Windscreen/rear window washer pump
Electric window motor on driver-side front door
Electric window motor on passenger-side front door
INT supply for dashboard control lights, parking control unit,
tyre pressure measurement control unit, electric wing mirror movement,
rain sensor, sunroof control unit, My Port infotelematic system socket,
electric rear view mirror
Instrument panel
INT supply for brake pedal switch (NC contact), clutch pedal switch,
interior heating unit, convergence control unit, sound system capabilities,
voltage stabiliser control unit, reverse light on rear bumper,
water sensor on diesel filter, glow plug heating control unit, airflow meter,
brake booster sensor, switch coils on engine compartment fuse box
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 203