ECU FIAT QUBO 2009 1.G User Guide

127
SAFETY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARDAND CONTROLS
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
IMPORTANT INFORMATION:
The sealing fluid of the fast tyre repair kit
is effective with external temperatures be-
tween –20 °C and +50 °C.
INFLATION PROCEDURE
Do not operate the com-
pressor for longer than 20
consecutive minutes. Risk of over-
heating. The fast repair kit is not suit-
able for permanent repairs. The tyres
may only be repaired temporarily.
WARNING
Put on the safety gloves pro-
vided together with the fast
tyre repair kit.
WARNING
The cylinder contains ethyl-
ene glycol. Contains latex:
may cause an allergic reaction.
Harmful if swallowed. Irritates the
eyes. May cause sensitization by in-
halation or contact. Avoid contact
with your eyes, skin and clothes. In
the event of contact, wash immedi-
ately with plenty of water. Do not in-
duce vomiting if swallowed. Rinse
your mouth and drink plenty of wa-
ter. Call a doctor immediately. Keep
away from children. The product
must not be used by asthmatics. Do
not breath in the vapours during in-
sertion and suction. Call a doctor im-
mediately if allergic reactions are not-
ed. Store the cylinder in the specific
compartment, away from sources of
heat. The sealing fluid will expire. Re-
place the cylinder containing the
sealant after the expiration date.
WARNING
Do not dispose of the cylinder
and contained sealant in the
environment. Dispose of them
according to the national and
local laws in force.
fig. 15F0T0190m
❒Ensure that the handbrake is up.
Remove the tyre valve cap, extract the
flexible filler tube A-fig. 15and fasten
the ring Bonto the tyre valve;
119-150 QUBO GB 1ed:123-154 Fiorino GB 1ed 3-12-2009 16:00 Pagina 127

138
SAFETY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARDAND CONTROLS
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
IF THE INTERIOR
LIGHT BURNS OUT
For the type of bulb and power rating, see
“When needing to change a bulb”.
FRONT CEILING LIGHT
Front ceiling light with
movable lens
To replace the bulbs proceed as follows:
❒remove the ceiling light A-fig. 35lev-
ering in the points shown by the ar-
rows;
❒open the lid B-fig. 36as indicated;❒replace bulb C-fig. 37releasing it from
the side contacts. Then, insert the new
bulb making sure it is correctly clamped
between the contacts;
❒close the lid and secure the ceiling light
in its housing locking it properly.
fig. 35F0T0106mfig. 36F0T0023m
fig. 37F0T0024m
119-150 QUBO GB 1ed:123-154 Fiorino GB 1ed 3-12-2009 16:00 Pagina 138

139
SAFETY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARDAND CONTROLS
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
Ceiling light with spot lights
(for versions/markets, where provided)
To replace the bulbs proceed as follows:
❒work in the points shown by the ar-
rows and remove light A-fig. 38;
❒open the protection door B-fig. 39;
❒replace bulbs Cafter releasing them
from the side contacts; make sure that
new bulbs are correctly clamped be-
tween contacts;
❒close the door B-fig. 39and secure the
ceiling light A-fig. 38in its housing lock-
ing it properly.REAR CEILING LIGHT
To change the bulb, proceed as follows:
❒remove the ceiling light A-fig. 40lev-
ering in the points shown by the ar-
rows;
❒open the lid B-fig. 41as indicated;
❒replace bulb C-fig. 42releasing it from
the side contacts. Then, insert the new
bulb making sure it is correctly clamped
between the contacts;
❒close the lid B-fig. 41and secure the
ceiling light in its housing locking it
properly.
fig. 38F0T0143mfig. 39F0T0144mfig. 40F0T0107m
fig. 41F0T0023m
fig. 42F0T0024m
119-150 QUBO GB 1ed:123-154 Fiorino GB 1ed 3-12-2009 16:00 Pagina 139

152
SAFETY
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARDAND CONTROLS
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
SCHEDULED SERVICING
Correct servicing is essential for ensur-
ing long vehicle life under the best condi-
tions.
This is why Fiat has planned a series of
checks and maintenance operations every
30,000 km.
Scheduled servicing will not however ful-
ly cover all of the needs of your vehicle.
Even before carrying out the 30,000 km
service coupon, and later between one
consecutive coupons, ordinary vehicle
care is still required such as for example
routine checks to top up the fluid levels,
if necessary, tyre pressure checks, etc.IMPORTANT Scheduled service coupons
are required by the manufacturer. Non-
performance of service coupons may
cause the warranty to become null and
void.
Scheduled Servicing is performed by all Fi-
at Dealerships at pre-established times.
If during scheduled servicing, the need aris-
es for further replacements or repairs,
these may be carried out exclusively af-
ter obtaining the explicit agreement from
the Customer.IMPORTANT You are advised to contact
the Fiat Dealership in the event of any mi-
nor operating faults, without waiting for
the next service coupon.
If your vehicle is used frequently for tow-
ing, the interval between service coupons
must be reduced.
151-172 QUBO GB 1ed:- 3-12-2009 12:01 Pagina 152

167
SAFETY
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARDAND CONTROLS
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
WINDSCREEN/
REAR WINDOW WIPER
(for versions/markets, where provided)
BLADES
Periodically clean the rubber part using
special products; TUTELA PROFES-
SIONAL SC 35is recommended.
Replace the blades if the rubber edge is de-
formed or worn. In all cases, it is advis-
able to replace them approximately once
a year.
Driving with worn wiper
blades is a serious hazard,
because visibility is reduced in bad
weather.
WARNING
Replacing the
windscreen wiper blades
Proceed as follows:
❒lift the windscreen wiper arm and posi-
tion the blade so that it forms an angle
of 90° with the arm itself;
❒exert pressure on the straps A-fig. 10
and remove the blade arm;
❒install the new blade by inserting the
straps into the supplied housings of the
arm. Make sure that the new blade is
secured in position.
fig. 10
A
A
F0T0087m
A few simple precautions can reduce the
possibility of damage to the blades:
❒make sure that the rubber part is not
stuck to the windscreen at sub-zero
temperatures. Use an antifreeze prod-
uct to release it if required.
❒remove the snow from the window:
this will avoid overstressing the elec-
trical motor in addition to protecting
the blades;
❒do not operate the windscreen and the
rear screen wipers on dry glass.
151-172 QUBO GB 1ed:- 3-12-2009 12:01 Pagina 167

168
SAFETY
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARDAND CONTROLS
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
Replacing the rear window wiper
blade
(for versions/markets, where provided)
Proceed as follows:
❒lift the cover A-fig. 11and disassemble
the arm from the vehicle by turning the
nut Bsecuring it to the rotation pin;
❒fit the new arm, positioning it correct-
ly, and fully tighten the nut;
❒lower the cover.SPRAY NOZZLES
If the jet of fluid is inadequate, firstly check
that there is fluid in the vessel of the wind-
screen/rear window wiper (for ver-
sions/markets, where provided) (see
“Checking fluid levels” in this section).
Then, make sure that the outlet holes are
not clogged. Unclog them using a needle,
if required.
Front window (window washer)
Front window washer jets are fixed. The
nozzle holders are positioned under the
bonnet (see fig. 12).Rear window
(rear window washer)
Rear window washer jets are fixed. The
nozzle holder is on the rear window (see
fig. 13).
fig. 11F0T0213mfig. 12F0T0090mfig. 13F0T0214m
151-172 QUBO GB 1ed:- 3-12-2009 12:01 Pagina 168