warning light FIAT STRADA 2014 Owner handbook (in English)
[x] Cancel search | Manufacturer: FIAT, Model Year: 2014, Model line: STRADA, Model: FIAT STRADA 2014Pages: 187, PDF Size: 8.06 MB
Page 30 of 187

28
IMPORTANT If the needle moves to
the beginning of the scale
(low temperature) with the
overheating warning light A on, this
indicates a fault in the system. If this
is the case, contact a Fiat Dealership
to have the system checked.
The needle may also approach the
red section when travelling too
slowly in a very hot climate. In this
case, it is best to stop for a while
and stop the engine.
Then restart and accelerate lightly.
fig. 38
F0X0302m
ENGINE COOLANT
TEMPERATURE GAUGE
fig. 37-38
If warning light A switches on in the
instrument panel, this indicates
overheating of the engine coolant.
In normal operating conditions, the
needle may move to various
positions within the scale according
to the vehicle usage conditions and
the management of the engine
cooling system performed
automatically by the system itself.
However, it should not move to the
red danger zone.
fig. 37
F0X0301m
IMPORTANT If the indicator shows
that the tank is empty and the
reserve warning light A-fig. 35-36
flashes, this indicates a fault in the
system. On some versions, the same
fault indication is provided by scale
C, which flashes on the display. If
this is the case, contact a Fiat
Dealership to have the system
checked.
007-044 STRADA LUM GB 1ed 9-01-2012 14:49 Pagina 28
Page 37 of 187

35
Initial checks
When the key is turned to MAR-
ON, the display begins a process of
diagnosis for the vehicle’s on-board
systems. This may last for a few
seconds. If, with the engine running,
the system does not detect any
faults, the system displays OK.
If the display indicates a fault, see
WARNING LIGHTS AND
MESSAGES in this section.
Speed limit exceeded
(Spd. Lim.)
This function allows the vehicle
speed limit to be set (km/h). When
this is exceeded, the driver is
notified through a dedicated
indication on the display, an acoustic
signal and a warning light (triangle
logo).
This indications are interrupted
immediately when the MODE
button is pressed. To set the speed limit, proceed as
follows:
– press the MODE button briefly to
enter the menu;
– press the ▼button; Spd. Lim. will
appear on the display;
– press the MODE button briefly,
then ▼or ▲to select ON or
OFF;
– to activate the function, press the
MODE button briefly when ON
flashes;
– press the ▼button: a speed value
will appear on the display;
– press the MODE button briefly:
the value will flash;
– set the new values as desired,
corresponding to the new speed
limit, by pressing the ▼and/or ▲
buttons.
– press the MODE button briefly to
confirm;
– hold down the MODE button to
return to the standard display.The speed limit can only be set to a
value of 30 km/h (or 20 mph) or
above. Every time the ▼or ▲
buttons are pressed, the value is
decreased/increased by 5 units
respectively When the buttons are
held down, the value decreases or
increases rapidly, as appropriate. It is
advisable to release the button as
you approach the desired value, then
complete the adjustment with single
presses.
The indication on the display is
interrupted automatically if the
vehicle speed falls below the set
value by at least 5 km/h (or 5 mph).
007-044 STRADA LUM GB 1ed 9-01-2012 14:49 Pagina 35
Page 43 of 187

41
Exit menu
This is the last option concluding the
menu function cycle.
– Press the MODE button briefly:
the display returns to the standard
screen.
– Pressing the ▼button returns to
the first menu option: Spd. Lim.Doors open warning
On some versions, the display
indicates which door has
inadvertently been left open.
On others, the “doors open”
warning light on the instrument
panel switches on in the same
circumstances. On some versions,
the system informs the driver that a
speed of 4 km/h has been exceeded
through an acoustic signal.
Exterior lighting check
The
Wwarning light switches on to
indicate a failure in one of the
external lights. On some versions,
the display can indicate the electrical
circuit where the fault is present.Interior lighting adjustment
(dimmer)
This function permits a decrease
and/or increase in light intensity for
the instrument panel, car radio
display and control button
serigraphy.
To adjust to the desired level, simply
press the ▼or ▲buttons; after a
few seconds, the display returns to
the previous screen automatically.
007-044 STRADA LUM GB 1ed 9-01-2012 14:49 Pagina 41
Page 47 of 187

BRAKE FLUID LOW
(red) / HANDBRAKE
ENGAGED (red)
When the key is turned to
MAR, the warning light switches on
but should switch off after a few
seconds.
Brake fluid low
The warning light switches on when
the level of the brake fluid in the
reservoir falls below the minimum
level, possibly due to a leak in the
circuit.
On some versions, the display shows
a dedicated message.
WARNING LIGHTS
AND MESSAGES
The warning light switches on
together with (where the instrument
panel permits) a specific message
and/or acoustic signal. These
indications are precautionary and as
such must not be considered as
exhaustive and/or alternative to the
information contained in the Owner
Handbook, which you are advised to
read carefully in all cases. Always
refer to the information in this
section in the event of a failure
indication.
IMPORTANT The failure indications
displayed are divided into two
categories: very serious and less
serious faults.
Very serious faults prompt a
prolonged cycle of signals.
Less serious faults prompt a shorter
cycle of signals.Warning lights (or the symbol on
the display) on the instrument panel
will stay on until the cause of the
failure is eliminated.
If the
xwarning light
switches on when
travelling (together with the
message on the display on
certain versions), stop the
vehicle immediately and
contact a Fiat Dealership.
WARNING
x
Handbrake engaged
The warning light switches on when
the handbrake is engaged.
On certain versions, if the vehicle is
in motion, the warning light switches
on together with an acoustic signal.
IMPORTANT If the warning light
switches on when travelling, check
that the handbrake is not engaged.
45
045-094 STRADA LUM GB 1ed 23-01-2012 9:10 Pagina 45
Page 48 of 187

PASSENGER AIRBAG
DEACTIVATED
(amber)
(for versions/markets,
where provided)
The Fwarning light switches on
when the front passenger side airbag
is deactivated.
With the front passenger airbag
enabled, when the ignition key is
turned to MAR, the Fwarning light
switches on constantly for about 4
seconds, flashes for another 4
seconds and then should switch off.
F
Failure of the F
warning light is
indicated by the
¬warning
light switching on.
In addition, the airbag system
automatically disables the
airbags on the passenger’s
side. Before proceeding,
contact a Fiat Dealership
immediately to have the
system checked.
WARNING
AIRBAG FAILURE
(red)
(for versions/markets,
where provided)
When the key is turned to MAR, the
warning light switches on but should
switch off after a few seconds. The
warning light switches on constantly
if there is a fault in the airbag system.
On some versions, the display shows
a dedicated message.
¬
If the ¬warning light
does not switch on when
the key is turned to MAR or
stays on when driving, there may
be a fault with the restraint
systems. In this case, the airbags
or the pretensioners may not be
activated in the case of an
accident or (in a lesser number
of cases) they may be activated
incorrectly. Contact a Fiat
Dealership immediately to have
the system checked.
WARNING
The failure of the ¬
warning light is
indicated by the flashing, for
more than the normal 4
seconds, of the front passenger
airbag deactivated warning
light
F. In addition, the
airbag system automatically
disables the airbags on the
passenger’s side (front airbag
and side bags for
versions/markets, where
provided). In this case, the
¬warning light may not indicate
faults in the restraint systems.
Before proceeding, contact a
Fiat Dealership immediately to
have the system checked.
WARNING
46
045-094 STRADA LUM GB 1ed 23-01-2012 9:10 Pagina 46
Page 49 of 187

EXCESSIVE ENGINE
COOLANT
TEMPERATURE (red)
When the key is turned to
MAR, the warning light switches on
but should switch off after a few
seconds.
The warning light turns on when the
engine is overheated.
If the warning light switches on,
proceed as follows:
– In the case of normal driving: stop
the vehicle, stop the engine and
check that the level of coolant in
the reservoir is not below the
MIN reference. In these
circumstances, wait a few minutes
to let the engine cool, then open
the reservoir cap slowly and
cautiously.
Top up with coolant, making sure
that the level of fluid is between
the MIN and MAX references on
the reservoir. Also check visually
for leaks. If, when restarting, the
warning light should come on
again, contact a Fiat Dealership.
ç
– If the vehicle is used under
demanding conditions (e.g. towing
trailers uphill or fully loaded): slow
down and, if the light stays on,
stop the vehicle.
Wait for 2 or 3 minutes with the
engine running and slightly
accelerated to further favour the
coolant circulation. Then stop the
engine. Check correct fluid level in
the reservoir as described above.IMPORTANT Over demanding
routes, it is advisable to keep the
engine on and slightly accelerated for
a few minutes before switching it off.
On some versions, the display shows
a dedicated message.
47
045-094 STRADA LUM GB 1ed 23-01-2012 9:10 Pagina 47
Page 50 of 187

ABS SYSTEM
FAILURE (amber)
When the key is turned to MAR, the
warning light switches on but should
switch off after a few seconds.
The warning light will switch on
when the system is either not
working or not available. In this case
the braking system maintains its own
efficiency unaltered, but without the
advantage of the ABS system.
Drive carefully and contact a Fiat
Dealership as soon as possible.
On some versions, the display shows
a dedicated message. BATTERY CHARGE
LOW (red)
The warning light switches
on when the ignition key is turned
to MAR, but it should switch off as
soon as the engine has started (with
the engine idling a brief delay before
switching off is acceptable).
If the warning light stays on, contact
a Fiat Dealership immediately.
On some versions, the display shows
a dedicated message.
w>x>
EBD FAILURE
(red - amber)
(for versions/
markets, where
provided)
If the
xand >warning lights
switch on simultaneously with the
engine running, this indicates that
there is a fault in the EBD system or
that the system in unavailable.
In this case, the rear wheels may
suddenly lock and the vehicle may
swerve when braking sharply. Drive
very carefully to a Fiat Dealership to
have the system inspected
immediately.
On some versions, the display shows
a dedicated message.
48
045-094 STRADA LUM GB 1ed 23-01-2012 9:10 Pagina 48
Page 51 of 187

Constant: LOW
ENGINE OIL
PRESSURE (red)
Flashing: ENGINE OIL
DETERIORATED
(red)
When the key is turned to MAR, the
warning light switches on, but should
switch off as soon as the engine is
started.
Low engine oil pressure
The warning light switches on
constantly, together with a message
(for versions/markets, where
provided) on the display, when the
system detects that engine oil
pressure is too low.
vIf the vwarning
light switches on when
the vehicle is travelling (on
certain versions together with a
message on the display) stop
the engine immediately and
contact a Fiat Dealership.
WARNING
Engine oil deteriorated
The
vwarning light starts to
flash together with a message on the
display (for versions/markets, where
provided) when the system detects
that the engine oil has deteriorated.
If the warning light flashes, this does
not mean that the vehicle is faulty,
but simply informs the driver that it
is now necessary to change the
engine oil as a result of regular
vehicle use.If the oil is not changed, when a
second deterioration threshold is
reached, the
Uwarning light also
switches on in the instrument panel
and engine operation is limited to
3000 rpm.
If the oil is still not changed, when a
third deterioration threshold is
reached, the engine is limited to
1500 rpm to avoid damage.
To avoid damaging the
engine you are advised
to change the engine oil
when the warning light
v
flashes. Contact a Fiat
Dealership.
49
045-094 STRADA LUM GB 1ed 23-01-2012 9:10 Pagina 49
Page 52 of 187

Contact a Fiat
Dealership as soon as
possible if the
U
warning light does not switch on
when the ignition key is turned
to MAR or if it switches on
when driving (together with a
message on the display on some
versions). The operation of the
Uwarning light may be
checked by the traffic control
authorities using specific
devices. Always comply with the
traffic regulations in force in the
country where you are driving.
INJECTION SYSTEM
FAILURE (amber)
In normal conditions, when the
ignition key is turned to MAR, the
warning light switches on, but should
switch off when the engine starts.
If the warning light stays on or
comes on when travelling, it means
there is a fault in the injection
system which could cause loss of
performance, poor handling and high
fuel consumption levels.
On some versions, the display shows
a dedicated message.
Under these conditions, the vehicle
can continue travelling at moderate
speed without demanding excessive
effort from the engine. In any case,
you should contact a Fiat Dealership
as soon as possible. DOORS NOT
CLOSED
CORRECTLY (red)
On certain versions, the warning
light switches on when one or more
doors are not closed correctly. On
some versions, the display shows a
dedicated message. On some
versions, an acoustic signal is emitted
when the vehicle is in motion.SEAT BELTS NOT
FASTENED (red)
(for versions/markets,
where provided)
When the ignition key is turned to
MAR-ON, the warning light flashes
10 times in 10 seconds, regardless of
whether or not the seat belt is
fastened.
<
´
U
50
FIAT CODE VEHICLE
PROTECTION
SYSTEM FAULT
(amber) (for versions/
markets where provided)
The warning light may come on
(and a message on the multifunction
display may appear on certain
versions) to indicate that there is a
fault in the Fiat Code system or, if
applicable, the alarm system; in this
case, contact a Fiat Dealership as
soon as possible.
Y
045-094 STRADA LUM GB 1ed 23-01-2012 9:10 Pagina 50
Page 53 of 187

FUEL RESERVE
(amber)
When the key is turned to MAR, the
warning light switches on but should
switch off after a few seconds.
The warning light switches on when
5.5 to 7.5 litres of fuel are left in the
tank.
On some versions, the
Kwarning
light flashes on the display.
ç
51
PLUG
PREHEATING/PLUG
PREHEATING
FAILURE (amber)
Plug preheating
This warning light switches on when
the key is turned to MAR. It will
switch off when the plugs have
reached a preset temperature.
Start the engine as soon as the
warning light switches off.
IMPORTANT At high ambient
temperatures, the warning light may
stay on for an extremely short time.
Plug preheating failure
The warning light flashes if there is a
fault in the plug preheating system.
Contact a Fiat Dealership as soon as
possible.
On some versions, the display shows
a dedicated message.
m
BRAKE PAD WEAR
(amber)
(for versions/markets,
where provided)
The warning light switches on if the
front brake pads are worn. In this
case replace them as soon as
possible.
On certain versions a dedicated
message is displayed.
d
045-094 STRADA LUM GB 1ed 23-01-2012 9:10 Pagina 51